Post on 11-Nov-2014
concreteinspection
equipment
www.elcometer.com
2
© Elcometer Instruments Limited, 2005 Elcometer, Protovale and Covermaster are registered trademarks of Elcometer Instruments Limited
All other Trademarks are acknowledged. All rights reserved. No part of this document may be reproduced, transmitted, stored (in a retrieval
system or otherwise), or translated into any language, in any form, or by any means, without the prior written permission of Elcometer. Due to our policy of continuous improvement, Elcometer reserve the right to change specifications without notice.
Version 2.0
www.elcometer.com
3
Table of Contents
Product Group Page
Introduction 4
Rebar Locators 8
Rebar, Wall Tie & Stud Locators 10
Concrete Covermeters 11
Concrete Test Hammers 17
Concrete Compression Testing (cubic moulds) 19
Adhesion & Bond Strength 20
Salt Contamination 24
Surface Roughness 27
Temperature & Climatic Condition Testing 29
Moisture Measurement 33
Crack Width Measurement 39
Magnifiers, Torches & Flashlights 41
International Standard Reference Numbers 43
Product Model Number Index 44
Index 45
Contact Information Back Cover
www.elcometer.com
4
Welcome to Elcometer For over 50 years Elcometer has been a world leader, not only in the manufacture and supply of quality inspection equipment, but also in the design and development of new products that meet or exceed customer requirements. Elcometer consolidated their world leading position with the acquisition of Protovale (Oxford) Limited - one of Europe’s premier concrete inspection equipment manufacturers. Since then Elcometer have been updating and expanding their products in order to provide you with a wide range of concrete inspection equipment to meet your requirements. The consolidation of Protovale into Elcometer’s Concrete and Civil Engineering Division has also allowed scale and scope for increased manufacturing and distribution efficiencies. With seven offices positioned in key markets around the world, Elcometer not only continues their tradition of quality and value, but also enhances their high level of technical support, customer service and product availability when and where you need it the most. Elcometer and the web For additional information, including latest product releases, free software, technical information, which exhibitions we will be attending, or to register for our free technical magazine, please visit our website; www.elcometer.com About Elcometer Elcometer’s extensive product range now includes:
• Concrete Inspection Equipment • Coating Inspection Equipment • Industrial Metal Detectors • Multiplexers and SPC
With such a wide range of products available, this catalogue has been designed to meet the requirements of the Concrete and Civil Engineering Industry. If you would like further information on our complete range of inspection equipment, please contact your nearest Elcometer Sales Office, as listed on the back of the catalogue.
www.elcometer.com
5
Why choose Elcometer? The philosophy of Elcometer since its inception in 1947 has always been to provide you with ‘best in class’ product design, product quality and service at a competitive price. By concentrating on these core values Elcometer has grown into a worldwide organisation with dedicated offices in seven countries and distribution outlets in more than 150 locations around the world
Technical Capability – engrained in our history
For more than 50 years Elcometer has been at the forefront of the Coating Inspection Industry. This involvement has also included presence on Standards Committees in many areas around the world. During this time many class-leading products have been designed and manufactured by Elcometer. With the introduction of the new range of Concrete and Civil Engineering Inspection Equipment, Elcometer has taken a further step in meeting the total needs of the inspection marketplace.
Research and Development
Elcometer commits major resources to Research and Development, with departments in both the UK and Belgian facilities. Elcometer are able to explore and exploit new and exciting areas of product development. This culminates in the capability to offer products which exceed customer expectations.
Innovation
Elcometer has had an enviable reputation for innovation since1947 when the world’s first mechanical coating thickness gauge was developed. This still holds true today and with recently released products such as the Elcometer Protovale 331 models B, S & T Covermeters - and a wide range of salt & chloride test equipment; the reputation of Elcometer grows from strength to strength.
Quality – a culture, not just about the products
Elcometer’s commitment to quality is reflected in our ISO 9001 Quality and ISO 14001 Environmental certifications.
However systems are only as good as the people who work with them and at Elcometer quality is a culture. The Company philosophy is to design quality into the product at the concept and development stage. This includes an environmental assessment of everything that Elcometer does – right down to this catalogue. This culture ensures that the product reaching the customer maintains the reputation that Elcometer has worked for so long to achieve. With facilities working to Kanban and Just in Time (JIT) methodology Elcometer’s manufacturing can also justifiably claim to be best in class.
abcde abcde
www.elcometer.com
6
Service - not just ‘after sales’ support! Elcometer’s Service concept includes: Product Sales: Elcometer never tries to ‘oversell’ a product that is not fit for purpose. The
philosophy is to cultivate and maintain customer relationships on a long-term basis. This ensures the continuity of the company.
Elcometer Sales Personnel are carefully trained in the application of the entire product range. This ensures that you, the customer, will be offered the product best suited for your purpose.
Application Support: With products being designed within the organisation, Elcometer can offer a
bespoke Application Advice and Support Service. This includes bespoke Product Sample Reports, advice on instrument application and problem solving available from our Technical Support help lines.
Customer Product Training: Even with carefully written Instruction Manuals there is an important need for
Elcometer to offer after sales product training. Such training can be carried out either at an Elcometer office or at your chosen location. With highly trained Technical Sales Personnel Elcometer prides itself in offering this service to our customers.
Elcometer have technical help desks operating in the UK, Belgium, France, Germany, Singapore and USA. There is therefore almost always an Elcometer office open somewhere in the world to handle your technical enquiry.
Product Service and Repair: From time to time even the best-engineered and manufactured products
require service or repair. The Elcometer worldwide network supports you with repair centres in the UK, Belgium, Singapore, USA and at many of our distributors facilities.
Elcometer also offers a comprehensive instrument calibration and certification service applicable to almost all of the products within the range. This service ensures that your instruments continue to meet the relevant National and International Standards.
Value for Money In the present competitive environment none of the above would matter unless Elcometer were price competitive. By constantly striving for optimised product design, lower costs, more efficient manufacturing and economical distribution, Elcometer’s strategy is to remain the industry benchmark.
www.elcometer.com
7
Worldwide Presence – a Global Organisation In order to satisfy the demands of the global market it is Elcometer’s strategy to be represented in all major markets worldwide. To achieve this Elcometer has a number of offices around the world which are dedicated to providing you, our customer, with a solution to your inspection needs. These offices, together with an international network of more than 150 distributors, ensure that Elcometer are available locally to both you and your customers whatever your industry or application. Manufacturing in two countries also provides us with the flexibility to tailor our output to meet world demand, further optimising our service to you.
www.elcometer.com
8
Rebar Locators
Rebar Locators Designed specifically to identify the location and orientation of reinforcement bars and other below surface metal objects. Locating steel reinforcement bars and metal pipes is essential in the construction and maintenance of structures. Damage caused when a drill or a fastener makes contact with a pipe is costly. A drill making contact with rebar, however, not only destroys the drill bit but also can seriously weaken the rebar, leading to serious structural damage. Before carrying out any maintenance work, it is vital to identify the location, orientation and depth of sub-surface metalwork.
The Elcometer Protovale 100 is a robust and economical gauge designed to identify the location and orientation of metal reinforcement bars, gas and water pipes.
Mild steel and stainless steel galvanised wall ties can also be found with the addition of an optional Search Coil (or probe).
Simple to use, the Elcometer Protovale 100 is supplied in an ABS plastic carry case, together with a 100mm (4”) search coil and batteries.
• Fast and accurate - gives a loud audible signal when the exact location of the rebar has been found.
• Directional Search field - distinguishes between horizontal and vertical bars – see diagram.
• No need to re-zero - Unaffected by moisture, temperature changes and electrical interference.
DETECTION RANGES FOR SINGLE REINFORCEMENT BARS
Rebar Diameter Detection Depth
mm inches mm inches
8 0.32 90 3.5
16 0.63 100 3.9
32 1.25 110 4.3
Model Description Part Number
Elcometer Protovale 100 Elcometer Protovale 100 Rebar Locator W100157A9D
100mm (4") Directional Search Coil for Rebar TW999198F
200mm (8") Hi-Depth Locator Search Coil - Short-handled (250mm) TW999198G
Accessories
200mm (8") Hi-Depth Locator Search Coil - Long-handled (650mm) TW999198H
Elcometer Protovale 100 Rebar Locator
At a glance • Low cost gauge used to accurately
identify the location & orientation of rebar & pipes.
• Optional Mild steel & stainless steel search head can be used to detect wall ties.
www.elcometer.com
9
Rebar Locators
The Elcometer Protovale 120 Rebar Locator, is perhaps the easiest and fastest way of detecting reinforcing bars in concrete.
Widely used before coring or drilling holes to find “safe spots”, the Elcometer Protovale 120 will not only indicate the rebar’s location and direction but also will give an indication of the depth of concrete cover.
Available in both metric and imperial versions, the Elcometer Protovale 120 is supplied together with a 100mm (4”) search coil, leather case and batteries.
• Fast, accurate and stable - A loud audio tone and a clear analogue meter for quick accurate scanning.
• Focussed search field - The Elcometer Protovale 120 is accurate even when working at close rebar centres, or near metal objects such as scaffolding or metal window frames.
• Highly directional detection field - The Elcometer Protovale 120 rebar locator can distinguish between horizontal and vertical bars.
• Headphone socket – Clearly detect the rebar in noisy environments.
Identification and Orientation of the bar
The Elcometer Protovale 120 can distinguish between horizontal and vertical bars.
After locating the steel reinforcement bars in the concrete, rotate the rebar locator’s search coil (probe) until the maximum and minimum signals are found.
The maximum signal indicates the bar is running parallel to the search coil’s handle, the minimum signal indicates that the bar is running at 90° to the search coil’s handle – see diagram.
DETECTION RANGES FOR SINGLE REINFORCEMENT BARS
Rebar Diameter Detection Depth Resolution of Parallel Bars
mm inches mm inches mm inches
8 0.32 120 4.72 60mm pitch at up to 35mm 2.36” pitch at up to 1.37”
16 0.63 140 5.50 75mm pitch at up to 50mm 2.95” pitch at up to 1.97”
32 1.25 160 6.30 150mm pitch at up to 85mm 5.90” pitch at up to 3.35”
Model Description Part Number
Elcometer Protovale 120/1 Elcometer Protovale 120 Rebar Locator - Metric W120155I
Elcometer Protovale 120/2 Elcometer Protovale 120 Rebar Locator - Imperial W120155J
Probe Lead for Elcometer Protovale 120 TW999165G
100mm (4") Directional Search Coil for Elcometer Protovale 120 TW999198F
Accessories
150mm (6") Extra-Depth Directional Search Coil for Elcometer Protovale 120 TW999198E
Elcometer Protovale 120 Rebar Locator
At a glance • Low cost gauge used to
determine location & orientation of reinforcement bars.
• Provides an approximate indication of the concrete cover above the located rebar.
www.elcometer.com
10
Rebar, Wall Tie & Stud Locators Rebar, Wall Tie & Stud Locators Any contractor engaged in maintenance work will be familiar with the problem of accurately locating the exact position of rebar, wall ties, studs and other metal fasteners. These low cost, simple to use gauges can meet your everyday requirements.
These fast, rugged instruments are designed to detect mild steel and/or stainless steel and non-ferrous metals. Each gauge is supplied with the appropriate number of search heads which determines the measurement capabilities of the gauge.
The Elcometer Protovale 130 Model D comes with a standard 100mm (4”) diameter head for the detection of mild steel.
The Elcometer Protovale 130 Model E is supplied with an additional 150mm (6”) diameter head extending the product’s capabilities to measure stainless steel, phosphor-bronze, copper and many other non-ferrous metals.
The Elcometer Protovale 150 Model E is supplied with three search heads. In addition to the two supplied with the Elcometer Protovale 130 Model E, it is supplied with a 100mm (4”) diameter directional search head which allows the user to determine the orientation of reinforcement bar and other metal objects such as bed joint reinforcement and hoop iron. It can even locate wiring in walls.
These small, battery operated gauges have:
• High-impact ABS control unit in a tough leather case.
• Built-in loudspeaker for clear audio signal; Standard 3.5mm (0.14”) stereo jack socket for headphones if required.
• Single control for both on/off and sensitivity/backoff control. Key Features
• Fast and accurate - The strongest signal is in the middle of the search head making it easy to pin point metal objects. A clear audio tone assists in the quick and precise location without the need to keep looking at the meter.
• Designed with the needs of the operator in mind – Easy to use, built to last, supplied with leather case and shoulder strap.
• Single handed operation – For safety and convenience when working on scaffold or ladders.
Model Description Part Number
Elcometer Protovale 130/D Elcometer Protovale 130 Wall-Tie Locator – Mild Steel. Complete with 100mm (4”) Locator Search Coil, Leather Case and Plastic Carry Case
W130157B9D
Elcometer Protovale 130/E Elcometer Protovale 130 Wall-Tie Locator – Mild & Stainless Steel. Complete with 100mm (4”) Locator Search Coil, 150mm (6”) Stainless Steel Search Coil, Leather Case and Plastic Carry Case
W130157C9E
Elcometer Protovale 150/E Elcometer Protovale 150 Rebar Locator, Mild & Stainless Steel Wall-Tie Locator. Complete with 100mm (4”) Locator Search Coil, 100mm (4”) Directional Search Coil, 150mm (6”) Stainless Steel Search Coil, Leather Case and Plastic Carry Case
W150157E9E
100mm (4”) Locator Search Coil TW999198D
100mm (4”) Directional Search Coil – Model E versions only. TW999198F
Accessories
150mm (6") Stainless Steel Search Coil – Model E versions only. TW999198E
Elcometer Protovale 130 & 150 Wall Tie & Stud Locators
At a glance
• Simple, highly accurate gauge for determining the precise location of mild or stainless steel wall ties, rebar, metal studs and fasteners.
www.elcometer.com
11
Concrete Covermeters
At a glance • Accurately identifies the location &
orientation of rebars in concrete. • Accurately measures the depth of
cover over the rebar. • Can be used close to other metal
objects without interference due to its targeted search head design.
Can be used in accordance with:
ACI 318 BS 1881:204
CP 110 DIN 1045
EC 2 SIA 162
Concrete Covermeters Locating steel reinforcement bars and metal pipes is essential in the construction and maintenance of structures. Damage caused when a drill or a fastener makes contact with a pipe is costly. A drill making contact with rebar or tendon ducts, however, not only destroys the drill bit but also can lead to serious structural damage. Before carrying out any maintenance work, it is vital to identify the location, orientation and depth of sub-surface metalwork. Elcometer has three covermeters in their range, these are listed below.
This simple to use gauge quickly and accurately locates, orientates and measures the depth of cover over reinforcement bars. Designed to meet IP65 this rugged waterproof gauge, supplied with a backlight as standard, can be used in the harshest of environments. Measuring concrete cover thickness with unparalleled accuracy the Elcometer Protovale 331 Model B is an entry level gauge for users who simply want to identify and measure the depth of the rebar.
• Accurately measure concrete cover thickness – the large graphics display clearly indicates the depth of cover; a signal strength indicator bar and variable tone speaker also identify when you are nearing rebar.
• Precise, rapid and easy location of bar direction - Simply rotate the detection probe to quickly and precisely find the direction of the reinforcement bar. The Elcometer Protovale 331 Model B can even locate and measure welded mesh fabrications.
• Easy to use – a fully menu driven gauge, in many languages, helps the user quickly navigate around the functions of the instrument.
• Single handed operation - The unique 4 key search heads from Elcometer allow almost all functions to be accessed whilst measuring.
• International bar sizes – the user can quickly select either Metric, Japanese and ASTM/Canadian bar sizes, or standard bar numbers for the USA.
• Continuous inspection 24 hours a day – each gauge is supplied with a quick release battery pack and charger. When the low-battery warning is displayed, simply replace the battery pack. Battery packs can be charged both inside or outside the gauge – allowing maximum usage of the instrument whilst on site.
Following the Elcometer philosophy of flexibility, the Elcometer Protovale 331 Covermeters have a wide range of optional accessories to meet many specialist needs:
• Identify subsequent layers of rebars & tendon ducts – connected to our Borehole Probe the Elcometer Protovale 331 Model B is able to detect rebars or tendon ducts behind layer after layer of rebar up to 100cm (40”) deep. See page 16 for further information.
• Measure in a wide range of congested situations – using the optional Narrow Pitch Search Head, the Elcometer Protovale 331 Model B can measure close to corners, castellated concrete surfaces, and pre-cast concrete units. Reinforced cages in concrete pipes can also be investigated.
• Extended Measurement Range – using the Deep Cover Search Head, the Elcometer Protovale 331 Model B’s measurement range can be extended to 180 mm (7”) of concrete cover.
For specifications, accessories and part numbers see pages 14 – 16
Elcometer Protovale 331 Model B Covermeter
www.elcometer.com
12
Concrete Covermeters
At a glance • Precisely identify the depth, location
& orientation of rebars. • Automatic bar sizing modes for
immediate bar diameter estimation. • Maxpip™ and Under Cover Modes
for additional surveying functionality • 1,000 reading memory – with
statistics
Can be used in accordance with:
ACI 318 BS 1881:204
CP 110 DIN 1045
EC 2 SIA 162
At a glance • Precisely identify the depth, location
& orientation of rebars. • Automatic bar sizing modes for
immediate bar diameter estimation • User definable grid pitch scales • Linear and grid data logging with
over 65,000 reading memory
Can be used in accordance with:
ACI 318 BS 1881:204
CP 110 DIN 1045
EC 2 SIA 162
The Elcometer Protovale 331 Model S Covermeter includes all of the features, flexibility and ease of use of the Model B, and has additional functionality making it the gauge of choice for structural and civil engineers and surveyors alike. Measuring concrete cover thickness with a very high level of accuracy, the Elcometer Protovale 331 Model S is an intermediate level gauge for users who want greater accuracy in measuring the depth of rebar together with a simple data storage capability for recording and downloading data at a later date.
• Automatic Rebar Sizing - the Elcometer Protovale 331 Model S has two modes of rebar estimation: Autosize - a quick estimation of the bar size, displayed in the main measurement mode; and Orthogonal – a more accurate method to determine the size of unknown bars.
• Under Cover Mode - the gauge’s buzzer only sounds when a minimum cover has been detected.
• Maxpip™ Mode - the buzzer only sounds when the search head has passed the centre of the rebar, ideal for fast identification of the layout of the rebar.
• Min / Max Cover Limits - program in minimum and/or maximum cover thickness values to monitor whether depth of cover is within specification.
• Data Logging and Statistics - 1,000 individual cover readings, and measurement statistics can be stored in the gauge’s memory and either printed on a directly connected printer or uploaded into your PC using Elcometer’s EDTS+ Excel Link or CoverMaster® software, supplied as standard with each instrument, for further evaluation and report generation - see page 13 for further information.
For specifications, accessories and part numbers see pages 14-16
Incorporating all the features and functionality of the Model B and Model S Covermeters, the Model T comes with the additional ability to store in excess of 65,000 readings in either individual batches or multiple spreadsheet (grid) style batch surveys. The ease of use of the Model T is not compromised by this additional functionality. The Elcometer Protovale 331 Covermeter range is controlled using a simple menu structure which helps the user get the most from the gauge, quickly and efficiently. With the inclusion of CoverMaster® software with each Elcometer Protovale 331 Model T, individual batches can be set up using the CoverMaster® PC Wizard and uploaded into the gauge for immediate surveying.
• Linear and Grid data logging - the Elcometer Protovale 331 Model T has two data logging methods, Linear – where data is simply stored in a batch, one reading after another; and Grid – where data is stored in a spreadsheet format each cell relating to a survey square marked out on the concrete.
• User definable ‘pitch scales’ – unlike other covermeters, the size of each survey square can be defined by the user.
• Wide range of batch headers - each batch has a wide range of identification fields for easy data management, these include: Site Name, Site Location, Measurement Location, Engineer’s Name, Customer’s Name, together with max & min cover limits and batch name. There is an additional field to add a survey note or instruction.
Elcometer Protovale 331 Model S Covermeter
Elcometer Protovale 331 Model T Covermeter
www.elcometer.com
13
Concrete Covermeters
Setup surveys on the PC using CoverMaster® software – Supplied free with each Elcometer Protovale 331 Model S and T, Elcometer’s CoverMaster® Software is designed to further simplify the setting up of your covermeter. This easy to use, powerful software package also enables you to utilise your site data – allowing you to not only generate accurate, clear and precise survey reports, but also to reliably save your individual readings and site surveys in this user friendly storage management system.
Data Management System: Store Inspection reports, site surveys & photographs together with all your other inspection information in one place – CoverMaster®
A typical data review screen on the model T version of the Elcometer Protovale 331
CoverMaster® Software: Data is quickly transferred to & from the covermeters. Accurate, professional reports can be created simply within the software.
Reports From the PC or the Gauge Simple reports can be printed out directly from the gauge – or Professionally created using CoverMaster® and submitted online or in written format.
A typical screen view of the Elcometer Protovale 331, displaying the preselected bar diameter & cover thickness values.
unit of measurement
selected cell
column id navigation softkeys; (left, shift, delete, right)
row id
reading below gauge range
reading below limit
reading above limit
no reading
reading above gauge range
A view of the full information that can be displayed on the model T version of the Elcometer Protovale 331
signal strengthindicator
batch name
data location
preselected bardiameter
auto sizingdiameter
menu softkeys
statistics battery indicator sensitivity / volume cover value (mm or inches) auto sizing cover value search head type
www.elcometer.com
14
Concrete Covermeters
Model B Model S Model T Rebar Location, Orientation & Depth of Cover Large Cover Thickness Reading in mm & inches Large Graphics Display with Backlight Multiple Language Menu Structure Signal Strength Bar Interchangeable Heads with LED & keypad User Selectable Bar Range Sizes & Numbers Measurement Sound Modes:
Locate (tone increases as head approaches rebar) Under Cover (tone only sounds for low cover) Maxpip™ (tone only as head passes rebar centre)
Autosize Mode Bar Diameter Determination
Orthogonal Mode Bar Diameter Determination RS232 Output - Direct to Printer or PC EDTS+ Excel Link Software CoverMaster® Software
Data Logging – with Alpha Numeric Batch Identification 1,000 readings in
a linear batch 65,000 readings in linear
or grid type batches Statistics Minimum & Maximum Cover Limits Date and Time Rugged Waterproof Case (IP65) Adjustable Beep Volume & Earphone Socket Upgradeable models
Bar Diameter Ranges Metric: USA Bar Numbers: ASTM/Canadian: Japanese:
5 - 50mm bar diameters in 21 values #2 - #18 bar diameters in 16 values 10 - 55M bar diameters in 8 values 6 - 57mm bar diameters in 17 values
Rechargeable Power Supply 7.4V lithium ion battery pack provides up to 32 hrs of continuous use (20 hrs if backlight switched on). Rechargeable in 4hrs either inside or outside the gauge, using an external charger.
Maximum Operating Temperature 50°C (122°F) Unit Dimensions (including standard head & lead) Size: 230 x 130 x 125mm (9 x 5.1 x 4.9”) Weight: 1.54kg (3.4lb)
Packing List Plastic ABS case complete with covermeter, standard head, rechargeable battery pack & charger, PC / printer cable, shoulder harness, instruction book and software - for Model S & T: EDTS+ Excel Link & CoverMaster® Software.
Part Number Description
UK 240V EUR 220V US 110V Elcometer Protovale 331 Model B W331B---1 W331B---2 W331B---3 Elcometer Protovale 331 Model S W331S---1 W331S---2 W331S---3 Elcometer Protovale 331 Model T W331T---1 W331T---2 W331T---3 Elcometer Dot Matrix Mini Printer X4569964B X4569964C X4569964D CoverMaster® Software (model S & T only) TW33119221 Calibration Certificate TWCAL-331 Spare / Additional Battery Pack TW33119038 Straight Cable - 1.8m (5.9ft) TW33119201 USB Interface Cable T99916716
Elcometer Protovale 331 Range Features & Specifications
www.elcometer.com
15
Concrete Covermeters
STANDARD SEARCH HEAD Overall 155 x 88 face x 42mm 6.10 x 3.5 face x 1.65”
Dimensions Sensing Area 120 x 60mm 4.72 x 2.36” 40mm (1.6”) bar 15mm to 95mm (0.6” to 3.75")
Range 8mm (0.3”) bar 8mm to 70mm (0.3” to 2.75") Up to 65mm (2.6”) depth ±2mm (±0.1”)
Accuracy Over 70mm (2.8”) depth ±3%
Pitch Resolution 16mm (#5) diameter bar at 50mm (2”) depth of cover, pitch ≥75mm (3”)
Supplied with all gauges this search head is
designed to meet almost all your measurement
requirements. Part Number TW33119124-1
NARROW PITCH SEARCH HEAD - OPTIONAL Overall 155 x 88 face x 42mm 6.10 x 3.5 face x 1.65”
Dimensions Sensing Area 120 x 60mm 4.72 x 2.36” 40mm (1.6”) bar 8mm to 80mm (0.3” to 3.1")
Range 8mm (0.3”) bar 5mm to 60mm (0.2” to 2.4") Up to 65mm (2.6”) depth ±2mm (±0.1”)
Accuracy Over 70mm (2.8”) depth ±3mm (±0.15”)
Pitch Resolution 10mm (#3) diameter bar at 30mm (1.2”) depth of cover, pitch ≥50mm (2”)
This search head is designed to accurately
measure cover thickness when the gaps between
each rebar (the pitch) are very small. Part Number TW33119124-2
DEEP COVER SEARCH HEAD - OPTIONAL Overall 170 x 94 x 54mm 6.7 x 3.7 x 2.1”
Dimensions Sensing Area 160 x 80mm 6.30 x 3.15” 40mm (1.6”) bar 35mm to 180mm (1.4” to 7")
Range 8mm (0.3”) bar 25mm to 160mm (1” to 6.3") Up to 65mm (2.6”) depth ±2mm (±0.1”)
Accuracy Over 70mm (2.8”) depth ±3%
Pitch Resolution 16mm (#5) diameter bar at 50mm (2”) depth of cover, pitch ≥75mm (3”)
When you need to search for rebars that are deep within the structure this search head is ideal.
See also the Borehole Probe on page 16. Part Number TW33119171
EXTENSION ARM KIT - OPTIONAL This allows the operator simple access to areas normally requiring ladders or scaffolding. Reduces the need to kneel down and allows the User to scan bridge decks and floor areas from a standing position. It can be connected to either the Standard or Narrow Pitch Search Head.
Part Number TW33119222
ELCOMETER PROTOVALE CALIBRATION TEST BLOCK – OPTIONAL This simple test block allows the user to confirm the measurement accuracy of their gauge using the four different cover thickness values identified on the test block.
Part Number TW33119218
Elcometer Protovale 331 Range Search Heads & Accessories
www.elcometer.com
16
Concrete Covermeters
ELCOMETER PROTOVALE BOREHOLE PROBE
The range of Protovale by Elcometer Concrete Covermeters are unequalled at finding the precise location and orientation of the first layers of reinforcing bars (rebars) with the transverse bar tied to it.
No covermeter will find subsequent layers of steel reinforcement deep within the concrete. Nor can they locate pre-stressing or post tensioning tendons underneath the top reinforcement. When the Elcometer Borehole Probe is connected to the Elcometer Protovale 331 the user can now locate rebar and tendon ducts at greater depths than any other covermeter on the market today.
• Reduce unnecessary boreholes - Significantly reduces abortive drilling that not only costs both time and money but also weakens structural integrity.
• Protect drills and reinforcement - The Probe warns you before you hit metal, reducing damage to drills, tendons and rebars.
• Drill holes faster and more safely - Drill with confidence knowing that you’re safe from hitting metal in the concrete over a measured distance
• Install anodes accurately - Use the Probe to install anodes at the correct distance from steel reinforcement.
• Directional location field - Rocker switch on probe head allows fast, easy change between forwards or sideways detection
• Measures depth of hole - The probe shaft is calibrated to measure depth drilled.
The 'easy' solution for finding tendon ducts and 'hidden' layers of rebar using a simple and reliable detection method.
Using the Elcometer Protovale 331 Covermeter, identify an area between the first layers of rebar - allowing you to drill a hole with a large enough diameter to fit the shaft of the Elcometer Borehole Probe.
The Elcometer Borehole Probe is then carefully pushed into the hole and information about the 'hidden' reinforcement, either (a) to the side of, or (b) in front of, the end of the probe, can be determined - see diagram. By rotating the probe and selecting the forwards or sideways sensing mode, reinforcement lying below the first layer of rebar can be quickly located.
By increasing the depth of the hole (if possible), and re-inserting the probe as necessary, the operator can quickly find steel rebars or tendon ducts deep within the concrete.
APPROXIMATE DETECTION RANGES TO THE SIDE AND IN FRONT OF THE BOREHOLE PROBE
Steel Object Probe Orientation (see diagram above) Tendon Duct - 70mm (2.75”) Dia. side of the probe (a): 60mm (2.36”) in front of probe (b): 90mm (3.54”) Reinforcement Bar side of the probe (a): 45mm (1.77”) in front of probe (b): 60mm (2.36”)
.
Measurement Length Metric Imperial Shaft Marking every 1cm or 0.5” Short Probe 0 – 40cm 0 – 16” Shaft Diameter 16mm (0.62”) Long Probe 0 – 100cm 0 – 40” Optimum Hole Dia. 20mm (0.78”)
Part Number Model Description Metric Imperial
Borehole Probe (Short) Elcometer Borehole Probe: Short Version TW33119223-1 TW33119223-3 Borehole Probe (Long) Elcometer Borehole Probe: Long Version TW33119223-2 TW33119223-4
covermeter borehole search head probe
reinforcement bars detection field
tendon duct
(a) (b)
www.elcometer.com
17
Concrete Test Hammers
Concrete Test Hammers
Test hammers are used to determine the surface hardness of concrete and are one of the most widely used instruments in the field of non destructive testing (NDT) of concrete compressive strength. It is the quickest, simplest and least expensive method to obtain an estimate of the quality and strength of the concrete.
Both mechanical and digital test hammers are available. This simple to use gauge consists of a spring loaded plunger which, when released, strikes the surface with fixed and constant impact energy. During the rebound stroke, the mass moves a pointer that indicates the maximum point of return and at the same time indicates a reference value called Rebound Number. This number, converted by the correlations available on the hammer, gives the compression resistance value in respect of the impact angle.
• Impact Energy 2.207 Nm • Supplied with abrasive stone to prepare test surface • Aluminium body • Rebound value indicated on test hammer • Rebound value chart on body, for quick calculation of compressive strength • Curve selection on chart dependant on testing angle
The concrete hammer is supplied with plastic carrying case, grinding stone and instructions.
Impact Energy 2.207 Nm Accuracy Better than +/- 2 Rebound Number (When tested on Calibration Anvil at 80) Resolution 2 Rebound Number(s) Range 10 to 100 Rebound Number Dimensions Hammer: 280mm (11.02”) length x 55mm (2.17”) diameter
In Case: 350mm (13.78”) length x 80mm (3.15”) diameter Weight 1.5kg (3.3lbs) with case Shipping List Hammer, abrasive stone and case
Model Description Part Number Elcometer 181/1 Elcometer 181 Mechanical Concrete Test Hammer – MPa Scale W181----1 Elcometer 181/2 Elcometer 181 Mechanical Concrete Test Hammer – PSI Scale W181----2
Calibration Certificate TWCAL-181 Accessories Calibration Anvil TW99919226
Elcometer 181 Mechanical Concrete Test Hammer
At a glance • Low cost method to estimate
the strength and quality of concrete
• Simple to use, immediate results
Can be used in accordance with:
ASTM C805 EN 12504-2
BS 1881:202 DIN 1048
ISO 8045 NFP18-417
UNI 9189
www.elcometer.com
18
Concrete Test Hammers
The digital and more advanced version, is equipped with an electronic transducer which converts the rebound values into a reading on the digital display. It displays a range of statistics and there is a facility to download to a PC. The software and digital display are integrated into the design of the hammer.
• Light and easy to use • High resolution and accuracy • Possibility to store, display and download data to PC • Setting of test parameters and factors (age, shape, correction factors) • Rapid and simple calibration procedure • Selection of testing angle • Selection of unit (N/mm2, MPa, PSI, kgf/cm2) • Automatic conversion of rebound index to equivalent compression strength • Selection between 7 different correlation curves between rebound index and
compressive strength, 2 pre-set and 5 user definable • Statistical evaluation of test results (mean value, standard deviation,
concrete strength estimation) • Supplied with abrasive stone to prepare test surface • Storage of up to 5000 results • RS 232 output to PC • Rechargeable internal battery
Impact Energy 2.207 Nm Accuracy Better than ± 2 Rebound Number(s) (When tested on Calibration Anvil at 80) Range 10 to 70 MPa Resolution 0.1 Rebound Number Memory 5,000 tests Unit Selection N/mm2; MPa; kg/cm2; PSI Autonomy (Continuous Use) >5 Hours Dimensions Hammer: 280mm (11.02”) length x 55mm (2.17”) diameter
In Case: 190 x 100 x 350mm (7.48” x 3.94” x 13.78”) Weight 2kg (4.4lbs) with case Shipping List Hammer, battery charger, serial cable for PC, abrasive stone, instruction manual, calibration
certificate and carry case
Part Number Model Description
UK 240V EUR 220V US 110V
Elcometer 182 Elcometer 182 Digital Concrete Test Hammer W182---1A W182---1B W182---1C Accessories Calibration Anvil TW99919226
Elcometer 182 Digital Concrete Test Hammer
At a glance • The gauge for the non
destructive testing of concrete hardness and compressive strength.
• Simple to use, immediate results displayed on the digital display
• Internal memory for up to 5,000 readings.
Can be used in accordance with:
ASTM C805 EN 12504-2
BS 1881:202 DIN 1048
ISO 8045 NFP18-417
UNI 9189
www.elcometer.com
19
Concrete Compression Testing
Concrete Compression Testing
The strength of the concrete is key in the construction process. The compressive strength of concretes and cements used in a structure are specified and carefully monitored. In order to control the quality of the mix, cubic or cylindrical concrete test samples are made and their compressive strength is tested by applying load. The Elcometer 190 Quick Beton® is an innovative, low cost, accurate cube mould for use in concrete compression and quality testing. Until now, in order to meet the stringent requirements of UNI EN 12390-1:2002, moulds have usually been solid metal castings – making test sample removal very difficult. This lightweight (800g, 1.76lb) mould is designed to allow samples to be removed with minimal effort. Two modular, identical half-shells are brought together and two side-clips are fixed into place in order to prevent them accidentally separating when the cement mix is poured in. The Elcometer 190 standardised cube mould is manufactured out of rigid plastic and generates precise cubic test samples of 150mm (5.9”) dimensions.
• Easy to assemble and breakdown - you do not need any tools for mounting the mould, no compressed air or chemical products to extract the sample – simply slide the side-clips away and remove the concrete cube.
• Cost & time saving - as the concrete sample manufactured with the Elcometer 190 has all the geometrical and physical specifications required to comply with the dimensional tolerances specified by UNI EN 12390-1:2002, there is no need to grind the surface of the cubes to get the end faces flat and parallel.
• A fully recyclable product - can be re-used at least 15 times • Immediate mould marking - print your test reference information on the
cube (concrete manufacturer, project name, etc.) – as early as immediately after pouring.
Each Elcometer 190 is supplied in a kit which contains 6 moulds, 6 side-clip pairs and 2 tamping rods.
Model Description Part Number
Elcometer 190 Elcometer 190 Quick Beton® Concrete Cube Compression Test Mould – 6 moulds per pack W190----1
Elcometer 190 Quick Beton® Concrete Cube Compression Test Mould
Can be used in accordance with:
BS1881
UNI EN 12390-1:2002
UNI EN 12390-2:2002
1 2
3 4
At a glance • Low cost, simple and time
saving method for the manufacture of samples for concrete compression & quality control tests.
www.elcometer.com
20
Adhesion & Bond Strength
Adhesion & Bond Strength
Adhesion gauges are essentially used to determine the bond strength between two layers. In this way, these easy to use gauges are ideal for measuring a wide range of applications, which include concrete structural repairs as well as other types of coating adhesion on concrete - such as paint, cement, wall plaster, etc. The basic principle of all the Elcometer Adhesion Gauges is as follows: a test dolly is glued to the surface and, once cured, pulled off. The tensile force required to remove the test dolly together with the coating is measured by the gauge. The Elcometer 106 adhesion testers have been specifically designed to measure paint on concrete, but can also be used to measure the bond strength of structural repairs.
Once the dolly has been adhered to the surface, the Elcometer 106 gauge is simply positioned over the dolly and a load applied using the handle. As the handle is rotated, the force applied increases and the scale on the side of the gauge indicates the force applied. Each gauge is supplied in a carrying case together with either 20mm (0.78”) or 50mm (2”) dollies – dependant on model version.
Range Model Description
N/mm2 (MPa) PSI Part Number
Elcometer 106/5 Elcometer 106/5 Adhesion Tester for 20mm (0.78”) dollies (0)-0.2 (0)-30 F106----5 Elcometer 106/1 Elcometer 106/1 Adhesion Tester for 20mm (0.78”) dollies (0)-3.5 (0)-500 F106----1 Elcometer 106/2 Elcometer 106/2 Adhesion Tester for 20mm (0.78”) dollies (0)-7 (0)-1000 F106----2 Elcometer 106/3 Elcometer 106/3 Adhesion Tester for 20mm (0.78”) dollies (0)-15 (0)-2000 F106----3 Elcometer 106/4 Elcometer 106/4 Adhesion Tester for 20mm (0.78”) dollies (0) -22 (0)-3200 F106----4 Elcometer 106/6 Elcometer 106/6 Adhesion Tester for 50mm (2”) dollies (0) – 3.5 (0) – 500 F106----6
100 Spare Dollies 20mm (0.78”) T1062895-
Spare 50mm (2”) Dollies (Pack of 5) T10618570 Araldite Epoxy Adhesive T99912906
Accessories
Large Base Ring T1062915-
Elcometer 106 Concrete Adhesion Gauge
Can be used in accordance with:
ACI 503R ANSI N5.12
ASTM D 4541 BS 1881:207
BS EN 24624 ISO 4624
NF T 30-062
Elcometer 106 Scale 6 above & Elcometer 106 Scale 1 inset
At a glance • Low cost method of determining the adhesion or
bond strength of a coating. • Simple to use and fully portable. • Ideal for coatings on concrete, wood, metal,
plastic, or any other substrate.
www.elcometer.com
21
Adhesion & Bond Strength This automatic adhesion tester is designed for measuring the bond strength of all types of concrete coatings, including: paints, thin films, thermal sprayed coatings, etc., on any shaped substrate.
A dolly is adhered to the surface and once the test head is connected, a tensile force is applied. The rate of application can be adjusted by the User.
• Portable and simple to use • Produces comparable test results in the laboratory and on site • Precision gauge with both MPa and PSI readings • 110/230V mains power (battery power optional) • All Elcometer 1920 models can have a data logging module built in when
new or retro-fitted into an existing testing machine. • Supplied in solid aluminium case
The Elcometer 1920 PAT™ Adhesion Tester is available in four versions:
6.3kN (1416lbf), 20kN (4496lbf), 40kN (8992lbf) 80kN (17984lbf)
Elcometer 1920 PAT™ Models are supplied in an aluminium carrying case complete with:
Calibration Certificate, Automatic Hydraulic Pump Unit with Control Display PAT™ Testing Head Hydraulic Cable Adaptor for mains power.
Accuracy ±1% of full scale Hydraulic System Drive Two-step servo motor Power 110/230V AC Weight Complete in Case 8.2kg (18lb) Battery Optional Case Dimensions 430 x 325 x 145mm (17 x 13 x 6”)
Model Description Scale Range Part Number Elcometer 1920/1 Elcometer 1920/1 PAT™ Adhesion Tester 6.3kN, 1416lbf K0001920M001 Elcometer 1920/2 Elcometer 1920/2 PAT™ Adhesion Tester 20kN, 4496lbf K0001920M002 Elcometer 1920/3 Elcometer 1920/3 PAT™ Adhesion Tester 40kN, 8992lbf K0001920M003 Elcometer 1920/4 Elcometer 1920/4 PAT™ Adhesion Tester 80kN, 17984lbf K0001920M004 For a complete range of accessories and test elements, see page 23
Elcometer 1920 PAT™ Adhesion Tester
At a glance • Automatic adhesion tester for
repeatable results • Wide range of test dollies
available • User adjustable rate of force
application
Can be used in accordance with:
ASTM D 4541 ASTM C 633
EN 24624 ISO 4624
www.elcometer.com
22
Adhesion & Bond Strength
The most popular model in the Elcometer PAT™ Adhesion tester range. A manual hydraulic tensile adhesion tester for measuring the bond strength of all types of concrete, cements, paint, thermal sprayed coatings, thin films, ceramics, etc. The standard self-levelling head unit, supplied with each PAT™ adhesion gauge ensures that the dolly is always pulled off perpendicular to the surface, thereby ensuring greater repeatability.
• Portable, precision gauge with both MPa and PSI readings • Accurate and comparable test results both in the laboratory and on site. • Testing of coatings on any shaped substrates, e.g. inside and outside pipe
surfaces. The Elcometer 1941 is designed particularly for testing with 50mm (2”) diameter test elements and with the square 50 x 50mm (2 x 2”) test element for adhesion testing of tile adhesives and other cementitious materials.
Elcometer 1940 & 1941 PAT™ Adhesion Testers are each supplied in an aluminium carry case, complete with a Calibration Certificate, Hydraulic Pull-Force Pump, Testing Head - 6.3kN, 20kN or 40kN (depending on gauge).
The Elcometer 1940 gauges are also supplied with 5 Test Elements – 20mm (0.79”) Diameter, HSS Cutting Tool for 20mm (0.79”) Diameter Test Elements and Hydraulic Cable.
The Elcometer 1941 gauges are supplied with an adaptor for 50mm (2”), 70.7 (2.78”) and 50 x 50mm (2 x 2”) diameter elements, Quick Release Type Testing Head, Testing Support Platform and Hydraulic Cable.
Maximum Certified Pull Force Elcometer 1940: 6.3kN Elcometer 1941/1: 17kN Elcometer 1941/2: 34kN
Weight of Tester Elcometer 1940: 1.25kg (45oz) Elcometer 1941/1: 11kg (24.25lb) Elcometer 1941/2: 11kg (24.25lb)
Accuracy ±1% of full scale Case Dimensions 400 x 300 x 170mm (16 x 12 x 7”)
Model Description Scale Range Part Number Elcometer 1940 Elcometer 1940 PAT™ GM01/6.3kN Adhesion Tester 6.3kN, 1416lbf K0001940M001 Elcometer 1941/1 Elcometer 1941/1 PAT™ GM04/20kN Adhesion Tester 20kN, 4496lbf K0001941M001 Elcometer 1941/2 Elcometer 1941/2 PAT™ GM04/40kN Adhesion Tester 40kN, 8992lbf K0001941M002
Additional/Replacement 20kN Testing Head 20kN, 4496lbf KT001910P502 Additional/Replacement 40kN Testing Head 40kN, 8992lbf KT001910P503
Accessories
Additional 6.3kN Testing Head 6.3kN, 1416lbf KT001910P501 For a complete range of accessories and test elements, see page 23
Elcometer 1940 & 1941 PAT™ Adhesion Testers
At a glance • Automatic adhesion tester for
repeatable results • Wide range of test dollies
available • User adjustable rate of force
application
Can be used in accordance with:
ASTM D 4541 ASTM C 633
EN 1542 ISO 4624
www.elcometer.com
23
Adhesion & Bond Strength
Test Element Diameter
Adhesion Range Part Number
mm inches MPa PSI
Valid for Elcometer
Models Pack of 10 Test Elements
Pack of 100 Test Elements
Support Ring
Hand Cutting Tool
8.2 0.32 120 17400 1920/1* & 1940* KT001910P004 KT001910P204 KT001910P108 KT001910P11614.2 0.56 40 5800 1920/1 & 1940 KT001910P005 KT001910P205 KT001910P109 KT001910P11720 0.79 20 2900 1920/1 & 1940 KT001910P006 KT001910P206 KT001910P110 KT001910P11825 0.98 40 5800 1920/2 & 1941/1 KT001910P007 KT001910P207 - KT001910P119
28.2 1.11 10 1450 1920/1 & 1940 KT001910P010 KT001910P210 KT001910P111 KT001910P12040 1.57 5 725 1920/1 & 1940 KT001910P011 KT001910P211 KT001910P112 KT001910P12150 2.0 3.2 460 1920/1** & 1940** KT001910P012 KT001910P212 - KT001910P12270 2.76 5 725 1920/2 & 1941/1 KT001910P018 KT001910P218 - -
50 x 50 square
2.0 x 2.0 square 7.85 1140 1920/1***, 1920/2,
1940*** & 1941/1 KT001910P016 KT001910P216 - -
*Must be used with part number KT001910P401
**Must be used with part number KT001910P402
***Must be used with part number KT001910P403
Description Part Number 8.2mm Adaptor for use with 6.3kN Testing Head KT001910P401 Support Ring & Adaptor for 50mm Diameter Test Elements for use with 6.3kN Testing Head KT001910P402 Support Ring & Adaptor for 50 x 50mm Square Test Elements for use with 6.3kN Testing Head KT001910P403 Support Ring & Adaptor for use with 20kN Testing Head KT001910P404 Support Ring & Adaptor for use with 40 & 80kN Testing Head KT001910P405 E900S Single Part Epoxy Adhesive, 5ml KT001910P600 M2000G Adhesive, 20g Bottle T99911135
For use with the Elcometer PAT™, Elcometer 106, and Elcometer 108 Adhesion Testers, this Portable Field Calibration Verification Unit is ideal for confirming your adhesion gauge calibration. Connect the appropriate pull stub to the unit, pull your adhesion tester and compare the adhesion tester reading to the reading on the Portable Calibration Unit’s Display.
Calibration Range 0-17MPa (5.3kN) on 20mm (0.79”) diameter dolly Accuracy Within ±1% of full scale Instrument Weight 2.4kg (5.3lb)
Model Description Part Number Elcometer 1970 Elcometer 1970 PFCV Unit K0001970M001
Elcometer 106 Adapter KT001970P001 Accessories Elcometer 108 Adapter KT001970P002
Elcometer PAT™ Adhesion Gauge Test Elements
Elcometer PAT™ Adhesion Gauge Accessories
Elcometer 1970 PFCV – Portable Field Calibration Verification Unit
www.elcometer.com
24
Salt Contamination
At a glance • Fast field test for measuring the
concentration of chlorides in concrete.
• Generate depth/concentration profiles of your concrete structure.
At a glance • Simple low cost test for field testing of Chloride Ions in Water. • No laboratory test required.
Salt Contamination
Structures located near the sea, or in countries where freezing conditions occur, are prone to chloride or salt contamination issues. Moist sea air, or salty water created from de-icing programs on road surfaces, can be absorbed by the porous concrete. Even when the moisture evaporates, the salt remains in the concrete – potentially increasing the risk of accelerated corrosion of the steel rebar.
Chlorides deposited on a concrete surface, either during gritting or salting of roads during freezing conditions or due to moist salty sea air, can be absorbed into the concrete.
As the water evaporates, the soluble salt is deposited and remains within the concrete structure. As more water is absorbed into the concrete structure, the level of salt contamination, together with the penetration depth, increases and may eventually reach the layers of rebar, increasing the rate of corrosion.
The Elcometer 134A is an easy to use, fast and accurate field test which allows you to determine the concentration of chloride ions of your structure and help you create a depth/concentration profile of the concrete. Simply drill a hole into the concrete and collect the required amount of waste material and pour in the test solution. Insert the titration tube and record the chloride concentration. By removing samples at known depths and recording the result, you can quickly generate a profile of the chloride concentration at different depths.
When mixing concrete it is important to monitor the level of chloride in the water. The Elcometer 134W Salt Detection Kit for Water is a simple to use, field test, which gives you an accurate value for the chloride content in the water. Simply pour a water sample into the box and test with the titration tube. The colour change indicates the chloride concentration.
Elcometer 134A Elcometer 134W Measuring Range 1 – 50ppm (µg/cm2) 10 – 2000ppm Scale Resolution 1ppm 10ppm Sampling Time 1.5 minutes 1.5 to 4 minutes Tests per Box 4 5 Colour Change Pink to White Pink to White Part Number E134----2 E134----1
Elcometer 134A Chloride Ion Test Kit for Concrete
Elcometer 134W Salt Detection Kit for Water
Can be used in accordance with:
BS EN ISO 11127-6 BS EN ISO 11127-7
BS 7079-F16 BS 7079-F17
www.elcometer.com
25
Salt Contamination
At a glance • Measure the surface salt
cleanliness of your structure with one field test kit.
• No additional laboratory work required
At a glance • On site go / no go fields test for
detecting the presence of Amine Blush or Amine Bloom on the coating surface.
• • Each test is fully disposable. • • No additional components
required.
Designed to accurately measure surface chloride, sulphate and nitrate ions in minutes. The Elcometer 134 ‘CSN Salts’ offers the user the ability of trouble-free testing in the field.
• All the components of the Elcometer CSN Test Kit are pre-measured and pre-dosed for complete accuracy.
• All results are recorded in parts per million (ppm) - no complicated calculations needed to transfer these to µg/cm2 as the tests of the Elcometer 134 CSN are designed to be on a ratio of 1:1
Supplied in an ABS plastic carry case for easy portability around the site, each field kit is supplied with full instructions attached to the inside lid, together with:
5 x Chloride Tests, 5 x Tests, together with 1 x Colorimeter, for Sulphate Testing, 5 x Nitrate Test Strips, 5 x Syringes (without needles)
All Elcometer 134CSN consumables can be replenished.
Model Description Part Number Elcometer 134 CSN Elcometer 134 Chloride, Sulphate, Nitrate Test Kit – 5 tests E134-CSN
1 set of 5 Chloride Tests T134---C Accessories Complete Refill Kit – fully refill your test kit with 5 tests for each ion T134-KIT
When using amine-cured epoxy resin coatings in a multi layer system, if the original coating cures in a low ambient temperature or in a high humidity environment, a surface oiliness or exudate may occur. “Amine Blush” or “Sweating” as it is commonly referred to, leads to inter-coat adhesion failure.
• •Easy to use o – Spray the ABC solution onto a test filter pad and apply to the
surface. o – Check for colour change if amine is present. o – After test, flush with clean, fresh water.
• Immediate result if amine blush is present. • Each kit is suitable for 75+ tests.
Each unit is supplied in a carrying case for easy transportaion to the site and comes complete with:
ABC Solution; Test Filter Pads; Protective Gloves and Sealable Sample Bags.
Model Description Part Number Elcometer 139 Elcometer 139 ABC Amine Blush Check E139----1
Elcometer 134 CSN – Chlorides, Sulphates & Nitrates
Can be used in accordance with:
ISO 8502-6 ISO 8502-9
Elcometer 139 ABC Amine Blush Check
www.elcometer.com
26
Salt Contamination
At a glance • A field based gauge for measuring
the level of soluble salts on a surface - with laboratory type accuracy.
Soluble salts on a surface are absorbed into a special filter paper soaked with distilled water. The Elcometer 130 measures the conductivity of wet paper, calculates the salt level and displays it in ug/cm2.
• Suitable for a wide range of shapes, orientations, surfaces and finishes • Quick and simple to use • Battery operated and portable • Confirms adequate cleaning of surfaces before coating, aiding the
prevention of premature coating failure • Shows salt build-up on vulnerable surfaces, which can be treated to
increase the lifetime of a coating • Test papers can be re-moistened and a similar test result can be achieved
- ideal for proof and ISO requirements • Accurate, repeatable, reproducible
Range 0.1 - 20µg/cm2 Resolution 0.1µg/cm2 Accuracy ±1% Operating Range 5 - 40ºC (41 to 104ºF) <80%
RH Weight 1.5kg (3.3lbs) Sampling Time 2 minutes Model Description Part Number Elcometer 130 Elcometer 130 Salt Contamination Meter E130----1
250ml Pure Water T13011344 100 High Purity Sample Papers T1304469-
Accessories
Medical Wipes (1 Pack) T1304472-
Elcometer 130 Salt Contamination Meter
www.elcometer.com
27
Surface Roughness
Surface Roughness Measuring the surface roughness of concrete is essential in many areas, in particular in areas where a non-slip coating is required.
If the concrete profile is too low, there is a higher risk of skidding, if the profile is too high, the customer may view it as a poor surface finish.
This is an easy to use gauge that measures the point-to-valley height of a concrete surface.
The average of a series of measurements provides an indication of the surface roughness and allows the surfaces to be compared as polishing and inspection proceeds.
• Simple and low cost • Metric and Imperial versions
Can be used in accordance with:
ASTM D 4417-B SABS 772
Model Metric Imperial
Range 0 - 1000mm 0 – 40 mils
Scale Resolution 2mm 0.1 mils
Dimensions (nominal) 105 x 55 x 25mm 4.1 x 2.2 x 1”
Weight 235g 8oz
Power Not Required
Part Numbers E123A--M- E123A--E-
The Elcometer 223 is a battery operated Digital Surface Profile Gauge which measures the roughness of a surface in a similar way to the Elcometer 123 analogue equivalent, but with the added benefit of direct RS232 output.
• RS232 output - for transfer of readings to a PC, printer, etc - providing a permanent record of your test results - no memory in gauge
• Metric and Imperial switchable • Increased resolution
Can be used in accordance with: ASTM D 4417-B SABS 772
Model Metric Imperial
Range 0 - 1000mm 0 – 40 mils
Scale Resolution 1mm 0.1 mils
Dimensions (nominal) 105 x 55 x 25mm 4.1 x 2.2 x 1”
Weight 365g 9oz
Power 3V Lithium CR2032 Battery
Part Numbers E223----2 (Elcometer 223 units are switchable)
Accessories Miniprinter including Printer Lead X2239964B
Elcometer 123 Surface Profile Gauge
Elcometer 223 Digital Surface Profile Gauge
www.elcometer.com
28
Surface Roughness
The Elcometer 225 Profile Putty Kit is an easy-to-use system which provides a permanent replica of the surface profile of concrete and other materials. A mould is used to force a two-part putty onto the concrete surface. When the putty has set, it is peeled of the concrete; the profile of the surface of the concrete is permanently recorded in the putty. The putty replica may then be visually compared to standards or analysed to provide quantative measurement of surface profile.
Model Description Part Number Elcometer 225 Elcometer 225 Profile Putty Kit E225----1
Can be used in accordance with: NACE No. 6 SSPC-SP 13 ICRI Visual Comparator Standards
Elcometer 225 Profile Putty Kit
www.elcometer.com
29
Temperature & Climate Condition Testing
At a glance • Available in °C and °F
versions. • Supplied complete with needle
or surface probe.
Temperature & Climatic Condition Testing During the application of concrete or asphalt, or in the laboratory, the monitoring of temperature and humidity is important. Elcometer provide a selection of hand held gauges for both on-site or laboratory use. Designed to cope with routine day to day use, the Elcometer 212 is the gauge to take fast, accurate measurements. Incorporating an auto-power on/off facility, by simply unfolding and folding the probe, the instrument switches on and off.
• Large easy to read display • Surface or Needle probe options available • Auto power on/off facility • °C or °F gauge versions available
°C Scale (with Needle or Surface Probe) °F Scale (with Needle or Surface Probe) Temperature Range -50 to 300°C -50 to 562°F Resolution 1°C 1°F Accuracy ±1% of the reading ±1°C ±1% of the reading ±2°F Ambient Temperature Range 0 to 50°C 0 to 122°F
Display 12.7mm Liquid Crystal Display 0.5“ Liquid Crystal Display Battery Type 12V MN21 Battery Battery Life Approximately 200 hours Auto Switch Off Time Approximately 5 minutes Case Dimensions 47 x 156 x 19mm 1.9 x 6.2 x 0.7” Probe Dimensions 110mm 4.3” Instrument Weight 100g 0.22lb
Model Description Part Number Elcometer 212/1 Digital Pocket Thermometer (°C) with Needle Probe G212----1 Elcometer 212/3 Digital Pocket Thermometer (°F) with Needle Probe G212----3 Elcometer 212/2 Digital Pocket Thermometer (°C) with Surface Probe G212----2 Elcometer 212/4 Digital Pocket Thermometer (°F) with Surface Probe G212----4
Elcometer 212 Digital Pocket Thermometer
www.elcometer.com
30
Temperature & Climate Condition Testing
At a glance • Hand-held instrument. • Non-contact temperature
measurements. • Spot ratio of 3:1
The Elcometer 213 Digital Thermometer allows quick and easy measurements for a wide range of applications using the K-type thermocouple:
• Elcometer 213/1: Measurement of surface and air temperatures • Elcometer 213/2: Measurement of liquid temperatures • Elcometer 213/3: Needle probe for soft material temperatures
Measures temperature in the range of -50°C to 850°C, (the maximum temperature is dependant on probe type), with high accuracy and resolution. Quick temperature response.
Accuracy ±1% of the reading ±1 digit Time Constant ~ 1 second Ambient Temperature 0 to 50°C Instrument Display Range -50 to 850°C Weight 200g (0.44lb) Power Supply 1 x 6F22 (9V) Battery
Elcometer 213/1 Elcometer 213/2 Elcometer 213/3 Operating Range Surface Probe: -50 to 600°C
Magnetic Probe: -50 to 150°C -50 to 1100°C
(850°C maximum for unit) -50 to 400°C
Part Number G213--M1B with Surface & Magnetic Probe
G213--M2B with Liquid Probe
G213--M3B with Needle Probe
Using non-contact infrared technology, the Elcometer 214 Digital quickly and accurately measures the surface temperature of non reflective materials.
With a spot ratio of 3:1. The closer you get to the object under inspection, the smaller the spot size and hence the more accurate the reading – see below.
Temperature Range -18 to 315°C (0 to 600°F) Ambient Temperature Range 10 to 52°C (50 to 125°F) Resolution 1°C (1°F) Accuracy ±2% of reading or ±2°C (±3°F) Field of View 3:1 Optics Ratio with a 25mm
Minimum Target Repeatability ±0.5% of reading ±1 digit
Emissivity Fixed at 0.95 Response Time 1 second Battery Life Approximately 100 hours Dimensions 184 x 43 x 19mm
(7.3 x 1.7 x 0.75”) Part Number G214----1
Elcometer 213 Digital Pocket Thermometer
At a glance • Can be used to measure
surface / air, liquid or soft material temperatures.
• Simple and easy-to-use
Elcometer 214 Infrared Digital Thermometer
www.elcometer.com
31
Temperature & Climate Condition Testing
At a glance • Quick & easy to use. • Fast, accurate measurements.• Laser pointer to pinpoint
exact area of measurement • °C / °F switchable
The Elcometer 214L Infrared Thermometer is compact, lightweight and easy to use. Simply aim, pull the trigger and display the surface temperature of the object being measured. Release the trigger to hold the reading.
The Elcometer 214L incorporates a clear, easy to read display with laser pointer, backlight and low battery indicator. Battery life is preserved by the auto switch off facility and the User’s ability to switch the backlight on or off as required.
The laser assisted alignment feature is useful for pinpointing the exact area of measurement.
Features include:
• Laser – switchable • °C / °F – switchable • Auto switch off
• Backlight – switchable • Hold facility • 8:1 Optics ratio as shown below
Temperature Range -20 to 270°C (-4 to 518°F) Resolution 1°C or 1°F Accuracy ±2% of reading or ±2°C (±4°F) whichever is the greater Field of View 8:1 optics ratio (25mm min target) Emissivity Fixed at 0.95 Response Time Approximately one second Display Custom LCD Battery Type 9V MN1604/PP3 Battery Life 100 hours continuous use Case Dimensions 58 x 79 x 159mm (2.2 x 3.1 x 6.2”) Instrument Weight 180g (0.4 lb) Part Number G214L----2
Elcometer 214L Infrared Digital Thermometer (Laser)
www.elcometer.com
32
Temperature & Climate Condition Testing
The Elcometer 319 has been designed to incorporate all the needs required for climate condition monitoring, in a single gauge.
• Air Temperature • Relative Humidity • Surface Temperature • Dewpoint Temperature • ∆T- The difference between dewpoint and surface temperature
Accessories available for the Elcometer 319 include: • Infrared Printer for direct print-out of each dataset • Liquid Temperature Probe for measuring liquids up to 300°C/572°F • Interface Cable and EDTS+ Excel Link Software to download your stored
measurements for further PC analysis
Alarm Indicating when the climatic conditions are ‘unsafe’ to paint
Memory Each Elcometer 319 can store features up to 99 datasets* in the internal memory
Date and Time Each dataset is stored with date and time stamps. Date and time can also be displayed on the screen
IR Output Direct infrared output to IR Printer
Cable Data Output All gauges are supplied with data output via a cable for linking directly to a PC (Note: Interface Cable and Software supplied separately, Part number T31916504)
Backlight To Measure in low light and darkened areas, switch on the backlight
Dataset* Reading Review See all the readings stored in the memory on the screen
Enhanced Resolution Two scale ranges, which automatically change dependant upon the readings, provides greater reading resolution and accuracy below 60°C (140°F)
Improved Durability A specially designed resilient case provides greater protection
Increased Accuracy and Stability Made by Rotronic® of Switzerland, the humidity sensor is now perhaps the most stable and accurate available
Fast Surface Probe Users can take more readings in less time with the rapid contact sensor * A dataset is one set of each of the readings i.e. air temperature, surface temperature, relative humidity, dewpoint and ∆T.
Metric Imperial
Air Temperature Range -20 to 60°C -4 to 140°F
Air Temperature Accuracy ±0.3°C ±0.6°F
Resolution 0.1°C 0.1°F
Surface Temperature Range -15 to 115°C 5 to 239°F
Surface Temperature Range 1 -30 to 60°C -22 to 140°F
Surface Temperature Range 1 Accuracy (Resolution) ±0.5°C (0.1°C) ±1.0°F (0.1°F)
Surface Temperature Range 2 60 to 300°C 140 to 572°F
Surface Temperature Range 2 Accuracy (Resolution) ±1.5°C (1°C) ±3.0°F (1°F)
Relative Humidity Range 3 to 98% RH 3 to 98% RH
Relative Humidity Accuracy (Resolution) ±3% RH (0.1% RH) ±3% RH (0.1% RH)
Weight 260g 0.57lb
Battery Type 3 x AA MN1500 LR6 Batteries
Battery Life 500+ hours (without use of the backlight)
Model Description Part Number Elcometer 319 Elcometer 319 Dewmeter G319----1
Liquid Temperature Probe T31916465 Surface Temperature Probe T31916466 EDTS+ Excel Link® Software and Interface Cable T31916504
Accessories
IR Printer X99913877
Can be used in accordance with:
BS 7079-B4 ISO 8502-4
NACE PR propo 97
Elcometer 319 Dewmeter
www.elcometer.com
33
Moisture Measurement
At a glance • Pinless gauge - substrate remains intact.• Small, portable, lightweight instrument. • Digital display
Moisture Measurement
As concrete structures are porous they can absorb moisture. It is therefore often necessary to measure and monitor the moisture content within the concrete.
Other substrates, which may have a high moisture content, include timber, fibreboard, plasterboard, gypsum and brick. The meter is simply placed on the material to be tested, the moisture content can be read off immediately. No need to drive pins into the substrate.
• Handy, pinless moisture meter for fast measurements. • No separate measuring electrodes or cables required. • Fully automatic adjustment of the indicator. • Setting device for automatic correction of the readings
depending on the species of wood.
The measuring principle of the COMPACT “A” is based on the dielectric constant or high frequency method.
Measuring Range 5 to 45% moisture content, with digital LCD readout and wood species selector switch. Suitable for timber up to 40 mm thick.
Dimensions 170 x 35 x 35mm (6.7 x 1.38 x 1.38”) Weight 180g (6.35oz) Power supply 9 V dry cell or rechargeable battery Part Number K0007400M021
The indicator is equipped with a digital LCD readout and a universally applicable ball sensor for non-destructive location of moisture concentration in all kinds of building materials as well as for assessment of moisture distribution in walls, floors and ceilings. Electronic structural moisture indicator using a patented technique based on the dielectric constant / high frequency method.
Measuring Range 0 to 100 digits Dimensions 200 x 35 x 35 mm (7.87 x 1.38 x 1.38”) Weight 190g (6.7oz) Power supply 9 V dry cell or rechargeable battery Part Number K0007400M023
Elcometer 7400 Compact “A” Moisture Meter
Elcometer 7400 Compact “B” Moisture Meter
At a glance • Handy rapid-action moisture indicator for
fast measurements. • No separate measuring electrodes or cables
required. • Fully automatic adjustment of the indicator.
www.elcometer.com
34
Moisture Measurement
At a glance • Compact, easy to use gauge. • Can be used to measure moisture content
of sawn timber, chipboard & fibreboard.• Measure moisture content in substrates
up to 25mm thick.
At a glance • Digital Gauge. • No pins - substrate remains intact. • Can be used to evaluate the degree
of moisture in concrete, fibreglass and wood to a depth of 3cm (1.2”)
The hand closes naturally around the ergonomic form of the housing so that the pins on the end of the instrument can be pressed into the material to be measured. The thin pins make it easy to measure the moisture content of normal gypsum or mixed plaster as well as sawn timber, chipboard and fibreboard materials up to a maximum thickness of 25 mm.
• Handy, quick pocket-sized moisture meter for speedy single or series measurements.
• Measurement of plaster moisture content with a direct readout in percentage of dry weight.
• Two-group wood species correction. • Completely automatic instrument setting. • No separate electrodes or leads required.
Measuring Range 0.3 to 3.5% moisture content for plaster, with large 3-digit LCD readout. 5 to 20% moisture content for wood with two-group species correction
Dimensions 200mm x 35mm x 35mm (7.87” x 1.38” x 1.38”) Weight 130g (4.6oz) Part Number K0007400M018
A handy and easy to use instrument. The Elcometer 7420 does not use pins and does not damage the substrate under test.
The gauge is simply placed onto the material to be evaluated and quickly indicates the degree of moisture in concrete, fibreglass or wood down to a depth of 3cm (1.2”)
• High frequency method used. • Digital display with moisture/dry comparison scale. • No damage to the surface
Model Description Part Number Elcometer 7420 Elcometer 7420 Digital Moisture Meter K0007420M001
Elcometer 7420 Digital Moisture Meter
Elcometer 7400 Compact Moisture Meter
www.elcometer.com
35
Moisture Measurement
At a glance • Measure percentage moisture
content of a material. • Analogue display with colour
coding indicating high / low levels of moisture.
• ‘Five Scales’ - wood 1, wood 2, plaster, concrete and a linear reference.
Moisture is one of the most frequent causes of paint failure and construction defects. The Elcometer 118 Surface Moisture Meter is a general purpose gauge which measures the percentage moisture content of a material.
The probe is pressed firmly against the test surface and the result is immediately displayed on the relevant scale.
The Elcometer 118 scale incorporates red and green colour coding, indicating high and low levels of moisture respectively.
• Lightweight and portable • Go/No Go concept • Analogue display for easy understanding • Simple and quick to use • Interchangeable pin electrodes
The analogue meter includes five scales:
• Wood 1 • Wood 2 • Plaster • Concrete • A linear reference scale for comparison only.
Tables of wood groups are included in the operating instructions.
Range - Wood 1 14% - 30% (% Moisture Content) Range - Wood 2 15% - 30% (% Moisture Content) Range - Plaster 8% - 20% (% Moisture Content) Range - Concrete 5% - 14% (% Moisture Content)
Range – Linear Reference 0 - 10 Instrument Dimensions 43 x 91 x 146 mm
(1.7" x 3.5" x 5.7") Resolution 1% (Not Linear Scale) Accuracy (Using electrical resistance standards)
±2% of reading
Display Colour Coded Analogue Scale Power 1 x 9V MN1604 PP3 Battery Instrument Weight 230g (0.5lb) Carry Case Dimensions 60 x 155 x 165mm
(2.4" x 6.1" x 6.5")
Model Description Part Number Elcometer 118 Elcometer 118 Surface Moisture Meter G118A---1
Elcometer 118 Surface Moisture Meter
www.elcometer.com
36
Moisture Measurement
At a glance • Measures wood moisture,
structural moisture, air humidity and temperature.
• Sophisticated, fully electronic measuring system for fast, accurate measurements.
• Wide range of electrodes for various applications.
Electronic four-in-one meter designed for measurement of moisture content, structural moisture, air humidity and temperature, with digital LCD readout. Automatic temperature compensation for wood temperatures between -10 and 80°C and very precise correction facility for all species of wood.
The very best of its kind, the Elcometer 7400 RTU 600 is the culmination of over 45 years’ experience in moisture and temperature measurement.
It has been specially developed for architects, contractors, surveyors or anyone requiring reliable moisture measurement.
This instrument is also ideal for monitoring artificial or natural drying of timber. The Elcometer 7400 RTU 600 incorporates a highly sophisticated, fully electronic 4-circuit measuring system for fast, accurate measurements. The four integrated measuring ranges can perform tasks which previously required several different instruments.
• Handy moisture meter and thermometer for rapid measurements. • Direct reading digital LCD readout. Resolution 0.1 % or 0.1°C. • Fully automatic calibration – no manual adjustment necessary. • Fast measurement of moisture of solid building materials using the
resistance method. • Non-destructive structural moisture measurement using active electrodes
B50 and B60 • Highest accuracy of readings by selecting meter setting depending on
species of wood. • Automatic compensation of wood temperature in the range between -10 and 90°C. • Precise temperature measurement by use of quadruple conductor PT100 temperature probes.
Dimensions 180 x 115 x 53mm (7.09 x 4.53 x 2.09”) Weight 390g (13.8oz) Power supply 9 V dry battery IEC6 F22 or rechargeable battery
CAN BE USED WITH THE FOLLOWING RANGE OF MEASURING ELECTRODES Electrode Measuring Range Structural Moisture M6, M6-150/250, M6-Bi 200/300, M20, M 20-OF 15,
M20-Bi 200/300, M21-100/250, M25, MB 35, B50 0 to 80 digits, conversion into % of dry weight by graph. 0 to 199 digits, scanning range using probe B50 or B60 for determination of moisture concentration, classification by table, or 0.3 to 8% of dry weight by conversion table, using probe B50 or B60. 2 to 8% of dry weight on testing concrete surfaces by probe MB35.
Air Humidity RF-T 28, RF-T 31, RF-T 32, RF-T 36 7 to 98 % R.H. Temperature Measurement
OT100, OTW 90, ET10, TT30,TT40, LT20 Dependant on probe selected
Wood Moisture Measurement
M18, M20, M20-HW 200/300, MH34 4 to 100% moisture content. 40 to 200% moisture content
For electrode part numbers and descriptions, see pages 35-36
Model Description Part Number Elcometer 7400/22 Elcometer 7400 Moisture Meter RTU600 K0007400M022 Elcometer 7400/08 Elcometer 7400 Moisture Meter RTU600 complete with M20 and RF-T 28 Electrode K0007400M008
Elcometer 7400 RTU 600 Moisture Meter
www.elcometer.com
37
Moisture Measurement
ELECTRODES FOR MOISTURE MEASUREMENT IN BUILDING MATERIALS Stick-in Electrode M6
For measurement on hard, set building materials (mortar, concrete, etc.). With two each electrode pins 23mm (0.90”), 40mm (1.56”) and 60mm (2.36”) long (only to be used with contact paste).
KT007400P007
Stick-in Electrode Pins M6-150/250
Extra thin probes for measuring the moisture content in building and insulating materials over expansion joints or through non-insulated intersecting tile joints. For use with electrodes M6 and M20.
Length: 150 x 3mm (5.90 x 0.12”) KT007400P008 Length: 250 x 2mm (9.84 x 0.08”) KT007400P009
Flat Electrode Pair M6-Bi 200/300
For measuring concrete or insulation materials in corner or expansion joints (with insulated shank).
Dimensions: 10 x 0.8 x 200mm (0.39 x 0.03 x 7.87”) KT007400P085 Dimensions: 10 x 0.8 x 300mm (0.39 x 0.03 x 11.8”) KT007400P086
Ram-in Electrode M18
For measurement in depth of timber up to about 180mm (7.10”) thick. Supplied with ten spare pins 40mm (1.56”) and 60mm (2.36”) long. Teflon insulated electrode needles for point measurements at different depths are also available
KT007400P002Drive-in Electrode M20
For measurement of timber up to 50mm (2”) thick. Electrode body is made of impact resistant plastic. Included in the delivery are ten spare pins 16mm (0.63”) and 23mm (0.90”).
KT007400P003Stick-in Electrode Pins M20-Bi 200/300
For moisture measurement of materials hidden beneath another panel or covering. (Only to be used with electrode M20).
Length: 200mm (7.87”) KT007400P023 Length: 300mm (11.8”) KT007400P024
Surface Measuring Caps M20-OF 15
For moisture measurements on surfaces without damaging the material. Effective up to depth of approximately 3mm (0.12”). (Only to be used with electrode M20).
KT007400P042Deep Electrodes M21-100/250
For deep measurements of all kinds of solid building materials in conjunction with contact paste. Length: 100mm (3.94”) KT007400P008 Length: 250mm (9.84”) KT007400P009
Pair of Brush Electrodes M25
Stainless steel electrodes, for moisture measurements on hard and soft building materials without contact paste.
KT007400P089
Active Electrode MB35
With integrated measuring circuit, designed for surface measurement on concrete, in particular before coating, painting or colour marking. Measuring range: 2 to 8 % of dry weight
KT007400P032Active Electrode MH34
With integrated measuring circuit for measurement of high moisture contents in coniferous wood, specially in case of water-borne storage and for pre-sorting of freshly cut timber for kiln drying. Measuring range: 40 to 200% moisture content.
KT007400P033Active Electrode B50
Designed for non-destructive location of moisture concentration in building materials and moisture distribution in walls, ceilings & floors. The electrode uses a patented process to help generate a penetration depth up to 120mm (4.72”) depending on the density of the tested building material.
KT007400P031
www.elcometer.com
38
Moisture Measurement
ELECTRODES FOR MEASUREMENT OF RELATIVE HUMIDITY Special Electrode RF-T28
For high-speed testing of air relative humidity & air temperature, connection cable supplied. Measuring range: 7 to 98% R.H., -10 to 80°C
KT007400P013
Plug-In Sensor RF-T31
For measurement of atmospheric moisture, water activity value or equilibrium moisture in bulk materials and solid substances, e.g. brickwork and other building materials.
Measuring range: 7 to 98% R.H., -10 to 80°C. Diameter 10mm (0.39”), sintered filter tip 32mm (1.26”) long. Insertion Length: 250mm (9.84”) KT007400P054 Insertion Length: 500mm (19.7”) KT007400P055
Blade Sensor RF-T32
For measurement of atmospheric humidity, water activity value and equilibrium moisture in paper, leather, textile and tobacco stores etc. Range of Measurement 7 to 98% R.H. -10 to 80°C. Flat elliptical probe 10 x 4mm (0.39x0.16”) Insertion Length: 250mm (9.84”) KT007400P059 Insertion Length: 500mm (19.7”) KT007400P060
Special Electrode RF-T36
For measurement of air humidity & air temperature, water activity value or equilibrium moisture in rooms, warehouses or solid substances (concrete, subflooring, masonry,etc.). Measuring range: 5 to 98% R.H., -5 to 60°C.
KT007400P067
ELECTRODES FOR TEMPERATURE MEASUREMENT ET10
Robust stick-in temperature sensor for solid substances, bulk materials and fluids.
Length of probe 100mm (3.94”), diameter 3mm (0.12”). Measuring range -50 to 250°C
KT007400P006
TT40
Robust immersion and combustion gas temperature sensor.
Length of probe 480mm (18.9”), diameter 5mm (0.20”), measuring range -50 to 350°C
KT007400P016 LT20
Fast reacting air/gas temperature sensor with probe
Length 480mm (18.9”), diameter 5mm (0.20”). Measuring range -20 to 200°C
KT007400P018 TT30
Robust immersion and combustion gas temperature sensor.
Length of probe 230mm (9.05”), diameter 3mm (0.12”). Measuring range -50 to 350°C
KT007400P017 ET50
Fast reacting stick-in temperature sensor for soft solid substances, bulk materials and Fluids.
Length of probe 120mm (4.72”), diameter 3.0mm (0.12m”). Measuring range -50 to 300°C
KT007400P014 OTW90
Angled special surface temperature sensor for use at veneer presses etc.
Length of probe 100mm (3.94”), diameter 5mm (0.20”). Measuring range -50 to 250°C
KT007400P051 OT100
Spring loaded, low mass surface temperature sensor, for use on wall surfaces, etc.
Length of probe 110mm (4.33”), diameter 5mm (0.20”). Measuring range -50 to 250°C
KT007400P015
www.elcometer.com
39
Crack Width Measurement
Crack Width Measurement A simple range of gauges used for the measurement of crack widths in concrete and other structures. This simple gauge has been designed specifically to provide inspectors with a low cost alternative to a graduated microscope when determining the width of a crack in concrete or other building materials.
Similar in size to a standard credit card, this transparent gauge is marked with a range of graded line. Each line is a specified width.
To use, position the gauge over the crack and identify which line is a similar width to the crack. Read off the width value.
Range Model Description
mm inches Part Number
Elcometer 143 Elcometer 143 Crack Width Ruler 0.10 – 2.50 0.004 – 0.100 E143----1
This very simple graduated x50 microscope is an ideal gauge for measuring the size of cracks in concrete.
With its internal illumination the User can quickly determine the crack width by counting the number of graduations and calculating the value.
Model Description Part Number Elcometer 900/1 Elcometer 900 Concrete Crack Microscope Metric W90018568-M Elcometer 900/2 Elcometer 900 Concrete Crack Microscope Imperial W90018568-E
The Elcometer 7210 is pocket size making it an extremely practical microscope for site inspections.
Giving x30 magnification and a built-in light source, the Elcometer 7210 Pocket Microscope is the ideal choice for close up investigation of defects and surface cleanliness.
Model Description Part Number Elcometer 7210 Elcometer 7210 Pocket Microscope K0007210M001
Elcometer 143 Crack Width Ruler
Elcometer 900 Concrete Crack Microscope
Elcometer 7210 Pocket Microscope
www.elcometer.com
40
Crack Width Measurement
A small robust and handy microscope with battery operated removable lighting unit.
A wide range of magnifications are available with scales graduated in mm.
Ideal for surface inspection and crack width determination.
• x20; 0.1 mm graduations • x60; 0.02 mm graduations • x200; 0.002 mm graduations • x40; 0.05 mm graduations • x100; 0.01 mm graduations • x300; 0.001 mm graduations
Model Description Magnification Part Number Elcometer 7220/1 Microscope with Graduated Reticule x20 K0007220M001 Elcometer 7220/2 Microscope with Graduated Reticule x40 K0007220M002 Elcometer 7220/3 Microscope with Graduated Reticule x60 K0007220M003 Elcometer 7220/4 Microscope with Graduated Reticule x100 K0007220M004 Elcometer 7220/5 Microscope with Graduated Reticule x200 K0007220M005 Elcometer 7220/6 Microscope with Graduated Reticule x300 K0007220M006
Elcometer 7220 Microscope with Reticules
www.elcometer.com
41
Inspection Accessories
Magnifiers, Torches & Flashlights During inspection sometimes the substrate or coating requires closer investigation. In dark or shaded areas, further investigation may require additional light.
From time to time a closer inspection of a surface is required to ascertain the exact conditions of the material profile, cleanliness etc.
• Light, battery powered, portable magnifier • Ideal for comparison with surface comparators • x10 magnification for close surface inspection • Scaled lens for easy measurement of surface features
Model Description Part Number Elcometer 137 Elcometer 137 Illuminated Magnifier H137----1
Many environments have low light or dark areas; ballast tanks, oil and gas tanks, etc. It is imperative, not only for safety reasons but also to be able to inspect the coating adequately, to have sufficient light.
The Elcometer 132 Safety Torch / Flash Light is explosion proof and meets the ATEX directive as category 2 equipment. It is approved to the latest EN Standards for electrical apparatus for potential explosive atmospheres.
This allows for use in Group II applications zones 1 & 2, IIA & IIB gases, where T4 temperature class permits.
Model Description Part Number Elcometer 132 Elcometer 132 Safety Torch / Flash Light H132---1A
Inspection mirrors are ideal for inspecting difficult to access areas - inside pipes, behind corners, underneath inspection tanks, and other inaccessible or awkward areas.
Mirrors are therefore an essential part of the inspector's equipment. Combined with the full range of test equipment from Elcometer, these high quality, robust mirrors help to provide a detailed examination of the component or project under inspection.
Model Description Part Number Elcometer 131/1A Telescopic inspection mirror which extends from 350mm (14") to 1400mm (55").
Mirror diameter is 63mm (2.5") H131---1A
Elcometer 131/2A An illuminated inspection mirror. Its flexible stem is useful when examining hidden areas. Mirror diameter is 63mm (2.5")
H131---2A
Elcometer 137 Illuminated Magnifier
Elcometer 132 Safety Torch / Flash Light
Elcometer 131 Inspection Mirrors
www.elcometer.com
42
Notes
NOTES
www.elcometer.com
43
Standards Index
International Standard Reference Numbers This non-exhaustive list of standards is provided for information purposes only. To check if our products complies to, or can be used in accordance with, a standard that is not listed below, please contact Elcometer.
Standard Reference Page Standard Reference Page
ACI ICRI
ACI 318 Concrete Covermeters 11 - 16 ICRI Visual Comparator Standards 28
ACI 503R Adhesion & Bond Strength 20
ISO
ANSI ISO 4624 Adhesion & Bond Strength 20 - 23
ANSI N5.12 Adhesion & Bond Strength 20 ISO 8045 Concrete Test Hammers 17 - 18
ISO 8502-4 Temperature & Climate ________Condition Testing
32
ASTM ISO 8502-6 Salt Contamination 25
ASTM C 805 Concrete Test Hammers 17 - 18 ISO 8502-9 Salt Contamination 25
ASTM C 633 Adhesion & Bond Strength 21 - 23
ASTM D 4417-B Surface Roughness 27 NACE
ASTM D 4541 Adhesion & Bond Strength 20 - 23 NACE PR propo 97 Temperature & Climate ________Condition Testing
32
NACE No. 6 Surface Profile 28
BS
BS 1881 Concrete Compression Test 19 NF
BS 1881:202 Concrete Test Hammers 17 - 18 NF P 18-417 Concrete Test Hammers 17 - 18
BS 1881:204 Concrete Covermeters 11 - 16 NF T 30-062 Adhesion & Bond Strength 20
BS 1881:207 Adhesion & Bond Strength 20
BS 7079-B4 Temperature & Climate ________Condition Testing
32 SABS
BS 7079-F16 Salt Contamination 24 SABS 772 Surface Roughness 27
BS 7079-F17 Salt Contamination 24
SIA
BS EN SIA 162 Concrete Covermeters 11 - 16
BS EN 24624 Adhesion & Bond Strength 20
SSPC
BS EN ISO SSPC-SP 13 Surface Profile 28
BS EN ISO 11127-6 Salt Contamination 24
BS EN ISO 11127-7 Salt Contamination 24 UNI
UNI 9189 Concrete Test Hammers 17 – 18
CP UNI EN 12390-1 Concrete Compression Test 19
CP 110 Concrete Covermeters 11 - 16 UNI EN 12390-2 Concrete Compression Test 19
DIN
DIN 1045 Concrete Covermeters 11 - 16
DIN 1048 Concrete Test Hammers 17 - 18
EC
EC 2 Concrete Covermeters 11 - 16
EN
EN 1542 Adhesion & Bond Strength 22
EN 12504-2 Concrete Test Hammers 17 - 18
EN 24624 Adhesion & Bond Strength 21 - 23
www.elcometer.com
44
Product Model Number Index
Product Model Number Index Below you will find a list of all the products listed in catalogue, in model number order. Elcometer also has a wide range of inspection equipment for coatings inspection, metal detection & live cable location, and products for gauge multiplexing and statistical process control. If you would like further information on this range of products, please contact Elcometer.
Model Description Page
100 Elcometer Protovale Rebar Locator 8
106 Elcometer Adhesion Gauge 20
118 Elcometer Surface Moisture Meter 35
120 Elcometer Protovale Rebar Locator 9
123 Elcometer Surface Profile Gauge 27
130 Elcometer Protovale Wall Tie & Stud Locator 10
130 Elcometer Salt Contamination Meter 26
131 Elcometer Inspection Mirrors 41
132 Elcometer Safety Torch / Flash Light 41
134 A Elcometer Chloride Ion Test Kit for Concrete 24
134 CSN Elcometer Chlorides, Sulphates & Nitrates Test Kit 25
134 W Elcometer Salt Detection Kit for Water 24
137 Elcometer Illuminated Magnifier 41
139 Elcometer Amine Blush Test Kit 25
143 Elcometer Crack Width Ruler 39
150 Elcometer Protovale Rebar, Wall Tie & Stud Locator 10
181 Elcometer Mechanical Concrete Test Hammer 17
182 Elcometer Digital Concrete Test Hammer 18
190 Elcometer Quick Beton® Concrete Cube Compression Test Mould 19
212 Elcometer Digital Pocket Thermometer 29
213 Elcometer Digital Pocket Thermometer 30
214 Elcometer Infrared Digital Thermometer 30
214 L Elcometer Infrared Digital Thermometer with Laser Pointer 31
223 Elcometer Digital Surface Profile Gauge 27
225 Elcometer Prolfie Putty Kit 28
319 Elcometer Dewmeter 32
331 Elcometer Protovale Concrete Covermeters 11 - 16
900 Elcometer Concrete Crack Microscope 39
1920 Elcometer PAT™ Adhesion Tester 21, 23
1940 Elcometer PAT™ Adhesion Tester 6.3kN 22 - 23
1941 Elcometer PAT™ Adhesion Testers 20 & 40kN 22 - 23
1970 Elcometer Portable Field Verification Unit 23
7210 Elcometer Pocket Microscope 39
7220 Elcometer Microscope with Reticules 40
7400 Elcometer Compact Moisture Meters 33 – 34
7400 RTU Elcometer RTU 600 Moisture Meter 36 – 38
7420 Elcometer Digital Moisture Meter 34
www.elcometer.com
45
Index A I S
About Elcometer 4 Illuminated Magnifier 41 Safety Flashlight 41
Accessories - Inspection 41 Industrial Metal Detectors 4 Safety Torch 41
Adhesion & Bond Strength 20 - 23 Infrared Thermometer 30 - 31 Salt Contamination 24 - 26
Adhesion Testers 20 - 23 Inspection Accessories 41 Salt Contamination Meter 26
Adhesive Compound 20, 23 Inspection Mirror 41 Salt Detection 24 - 26
Amine Bloom / Blush 25 Interchangeable Search Heads 14 - 16 Salt Detection - Water 24
Analogue Moisture Meter 33 International Bar Sizes 11 - 16 Search Coil 8 - 10
Application Support 6 IR Thermometer 30 - 31 Search Head 15 - 16
Automatic Rebar Sizing 12 ISO 14001 5 Search Head - Deep Cover 15
B ISO 9001 5 Search Head - Extension Arm 15
Bar Size Estimation 12 - 16 L Search Head - Narrow Pitch 15
Batch Headers 12 Laser - Thermometer 31 Search Head - Standard 15
Bond Strength 20 - 23 Linear Data Logging 12 Service & Repair 6
Borehole Probe 16, 11 - 16 Liquid Thermometer 29 - 31 Site Survey 13
C Locate Mode 11 - 16 SPC 4
Calibration Block - Covermeters 15 M Spreadsheet Data Logging 12 - 13
Cement Adhesion Tester 20 - 23 Magnifier - Illuminated 41 Stainless Steel Rebar Locator 10
Chloride Ion Test Kit 24 Maximum Cover Limit 12 Standards Index 43
Climate Condition Testing 29 - 32 Maxpip™ Mode 12 Stud Locator 10
Coating inspection Equipment 4 Mechanical Test Hammer 17 Sulphate Detection 25
Compressive Strength 17 - 18 Metal Fastener Locator 10 Surface Dampness 33 - 38
Concrete Compressive Strength 17 – 18, 19 Microscopes 39 - 40 Surface Moisture 33 - 38
Concrete Cover Thickness 11 - 16 Minimum Cover Limit 12 Surface Profile 27
Concrete Covermeter 11 - 16 Mirror 41 Surface Roughness 27
Concrete Covermeters 11 - 16 Moisture Measurement 33 - 38 Surface Strength (rebound method) 17 - 18
Concrete Crack Microscopes 39 - 40 Moisture Meters 33 - 38 Surface Thermometer 29–31, 35
Concrete Mould Cube 19 Mould – Concrete Compression Test 19 T
Concrete Test Hammers 17 - 18 Multiplexers 4 Temperature 29 - 32
Cover Thickness Measurement 11 - 16 N Tendon Duct Locator 16, 11 - 16
CoverMaster® Software 12 - 13 Narrow Pitch 11 - 16 Test Hammers - Concrete 17 - 18
Crack Width Microscope, Measurement 39 - 40 Nitrate Detection 25 Test Stubs 20, 23
CSN Test Kit 25 O Thermometers 29 - 31
Cube – Concrete Compression Test 19 Orientation of Rebar 8 - 16 Torch 41
D Orthogonal Mode 12 - 15 U
Data logging 12 P Under Cover Mode 12
Deep Cover 11 - 16 PAT™ Adhesion Testers 21 - 23 User Definable Pitch Scales 12
Dew Point 32 Plaster Adhesion Tester 20 - 23 V
Digital Moisture Meter 33 - 34 Product Model Index 44 Value for Money 6
Digital Test Hammer 18 Product Training - Customer 6 W
Directional Search Field 8 - 10 Professional Report Generation 13 Wall Tie Locator 10
Dollies 20, 23 Profile Putty 28 Welded Mesh Locator 11 - 16
E Pull-off Strength 20 - 23 Why Choose Elcometer? 5
EDTS+ Excel Link 12 Q Worldwide Presence 7
Electrodes - Moisture 37 - 38 Quality - a Culture 5
Extension Arm 15 R
F Rebar Locators 8 - 16
Flashlight 41 Rebar, Wall Tie & Stud Locators 10
G Rebound Number 17 - 18
Grid Data Logging 12 Reinforcement Bar Location 8 - 16
H Relative Humidity 32
Hydraulic Adhesion Tester 22 Repair 6
Research and Development 5
Reticules - Microscope 40
Thank you for considering Elcometer as your partner
www.elcometer.com
www.elcometer.com
47
coating inspection equipment metal detection equipment
To request our complete inspection equipment catalogue, please contact Elcometer or visit our website, www.elcometer.com
Fineness of GrindViscosity
DensityBalances
MixersFlash Point
Film Application & Test ChartsDrying Time
Washability, Brushability & AbrasionHardness
Elasticity & Resistance DeformationAppearance
Stackability & Internal StressCorrosion
Material ThicknessSurface Profile
Surface CleanlinessClimatic Condition Testing
Oven Temperature Data RecordersMoisture Measurement
Wet Film ThicknessPowder Thickness
Dry Film ThicknessInspection Management Software
AdhesionPinhole & Porosity Detection
Inspection KitsPublications
Inspection Accessories
Industrial Metal DetectorsLive Cable Locators
SPC EquipmentGauge Multiplexers
ENGLAND Tel: +44 (0) 161 371 6000 Fax: +44 (0) 161 371 6010 e-mail: sales@elcometer.com www.elcometer.com
USA Tel: +1 248 650 0500 Toll free: 800 521 0635 Fax: +1 248 650 0501 e-mail: inc@elcometer.com www.elcometer.com
CANADA Tel: +1 248 650 0500 Toll Free: 800 521 0635 Fax: +1 248 650 0501 e-mail: ca_info@elcometer.com www.elcometer.com
SINGAPORE Tel: +65 6462 2822 Fax: +65 6462 2860 e-mail: asia@elcometer.com www.elcometer.com
BELGIUM Tel: +32 (0)4 379 96 10 Fax: +32 (0)4 374 06 03 e-mail: be_info@elcometer.be www.elcometer.be
FRANCE Tel: +33 (0)2 38 86 33 44 Fax: +33 (0)2 38 91 37 66 e-mail: fr_info@elcometer.fr www.elcometer.fr
GERMANY Tel: +49 (0) 7366 91 92 83 Fax: +49 (0) 7366 91 92 86 e-mail: de_info@elcometer.de www.elcometer.de
For your local specialist, please contact