Post on 02-Apr-2018
7/27/2019 Table Mil Std 105e
1/19
KUMPULAN TABEL MIL-STD-105E
Ir. Budi Nurtama, M.Agr.
2008
Program Studi Supervisor Jaminan Mutu PanganPROGRAM DIPLOMA
Institut Pertanian Bogor
7/27/2019 Table Mil Std 105e
2/19
i
Tables for MIL-STD-105E*)
Page
Table I. Sample-Size Code Letters. 1
Table II-A. Single Sampling Plans for Normal Inspection (Master Table). 2
Table II-B. Single Sampling Plans for Tightened Inspection (Master Table). 3
Table II-C. Single Sampling Plans for Reduced Inspection (Master Table). 4
Table III-A. Double Sampling Plans for Normal Inspection (Master Table). 5
Table III-B. Double Sampling Plans for Tightened Inspection (Master Table). 6
Table III-C. Double Sampling Plans for Reduced Inspection (Master Table). 7
Table IV-A. Multiple Sampling Plans for Normal Inspection (Master Table). 8
Table IV-A.(continued) 9
Table IV-B. Multiple Sampling Plans for Tightened Inspection (Master Table). 10
Table IV-B.(continued). 11
Table IV-C. Multiple Sampling Plans for Reduced Inspection (Master Table). 12
Table IV-C.(continued). 13
Table V-A. Average Outgoing Quality Limit Factors for Normal Inspection (Single Sampling). 14
Table V-A. Average Outgoing Quality Limit Factors for Tightened Inspection (Single Sampling). 15
Table VIII. Limit Numbers for Reduced Inspection. 16
*)Farnum, Nicholas R. 1994. Modern Statistical Quality Control and Improvement. Wadsworth, Inc., California.
7/27/2019 Table Mil Std 105e
3/19
ii
Tahapan Implementasi MIL-STD-105E
1. TentukanAQL (Acceptable Quality Level)berdasarkan perjanjian produsen dan pelanggan.
2. Tetapkan modus dan tingkat inspeksi (jika tidak, gunakanNormal Inspection,Level II).
3. Tentukan ukuran lot (lot size).
4. Gunakan tabel Sample Size Code Letters untuk memilih huruf kode yang sesuai.
5. Tetapkan tipe prosedur pengambilan sampel : single, double, atau multiple sampling.
6. Gunakan tabel yang berkaitan dengan prosedur pengambilan sampel terpilih (tahap 5) dan modus/tingkat inspeksi (tahap 2) untuk mendapatkan ukuran sampel
dan angka penerimaan (Ac) serta angka penolakan (Re). Dalam kasus dimana suatu rancangan tidak ada untuk ukuran lot dan AQL-nya, hati-hati mengikuti
tanda panah dalam tabel ke rancangan terdekat yang ada.
7. Mulailah gunakan rancangan tersebut dan catat penerimaan dan penolakan sehingga switching rule dapat diterapkan. Jika switching dilakukan, tentukan modus
dan tingkat dan ulangi tahap 4-6 untuk mendapatkan rancangan pengambilan sampel yang baru.
SWITCHING RULE for MIL-STD-105E
DariNormal ke Tightened Inspection : setelah 2 lot ditolak dari 2, 3, 4, atau 5 lot berurutan
Dari Tightened keNormal Inspection : setelah 5 lot berurutan diterima
DariNormal keReduced Inspection : jika (i) 10 lot berurutan diterima, dan (ii) jumlah total nonconforming items dalam 10 lot tersebut tidak melebihi batas
pada Table VIII. Limit Numbers for Reduced Inspection., dan (iii) produksi stabil/mantap, dan (iv) disetujui oleh otoritas
yang bertanggungjawab.
DariReduced keNormal Inspection : jika (i) suatu lot tunggal ditolak, atau (ii) suatu lot hanya sebagian dapat diterima (dhi. jumlah nonconforming items
diantara angka diterima dan ditolak), atau (iii) produksi menjadi tidak stabil, atau (iv) kondisi-kondisi lain yang
menjamin bahwa inspeksi Normal dapat dilakukan.
7/27/2019 Table Mil Std 105e
4/19
1
Table I. Sample-Size Code Letters.
Lot or batch size
Special Inspection Levels General Inspection Levels
S-1 S-2 S-3 S-4 I II III
2 to 8
9 to 15
16 to 25
A
A
A
A
A
A
A
A
B
A
A
B
A
A
B
A
B
C
B
C
D
26 to 50
51 to 90
91 to 150
A
B
B
B
B
B
B
C
C
C
C
D
C
C
D
D
E
F
E
F
G
151 to 280
281 to 500
501 to 1,200
B
B
C
C
C
C
D
D
E
E
E
F
E
F
G
G
H
J
H
J
K
1,201 to 3,200
3,201 to 10,000
10,001 to 35,000
C
C
C
D
D
D
E
F
F
G
G
H
H
J
K
K
L
M
L
M
N
35,001 to 150,000
150,001 to 500,000
500,001 and over
D
D
D
E
E
E
G
G
H
J
J
K
L
M
N
N
P
Q
P
Q
R
7/27/2019 Table Mil Std 105e
5/19
2
Table II - A. Single Sampling Plans for Normal Inspection (Master Table).
Samplesizecodeletter
Samplesize
Acceptable Quality Levels (normal inspection)
0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0 1.5 2.5 4.0 6.5 10 15 25 40 65 100 150 250 400 650 1000
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
A
B
C
2
3
5 0 1
0 1
0 1
1 2
1 2
2 3
1 2
2 3
3 4
2 3
3 4
5 6
3 4
5 6
7 8
5 6
7 8
10 11
7 8
10 11
14 15
10 11
14 15
21 22
14 15
21 22
30 31
21 22
30 31
44 45
30 31
44 45
D
E
F
8
13
20 0 1
0 1
0 1
1 2
1 2
2 3
1 2
2 3
3 4
2 3
3 4
5 6
3 4
5 6
7 8
5 6
7 8
10 11
7 8
10 11
14 15
10 11
14 15
21 22
14 15
21 22
21 22
30 31
30 31
44 45
44 45
G
H
J
32
50
80 0 1
0 1
0 1
1 2
1 2
2 3
1 2
2 3
3 4
2 3
3 4
5 6
3 4
5 6
7 8
5 6
7 8
10 11
7 8
10 11
14 15
10 11
14 15
21 22
14 15
21 22
21 22
K
L
M
125
200
315 0 1
0 1
0 1
1 2
1 2
2 3
1 2
2 3
3 4
2 3
3 4
5 6
3 4
5 6
7 8
5 6
7 8
10 11
7 8
10 11
14 15
10 11
14 15
21 22
14 15
21 22
21 22
N
P
Q
500
800
1250 0 1
0 1
0 1
1 2
1 2
2 3
1 2
2 3
3 4
2 3
3 4
5 6
3 4
5 6
7 8
5 6
7 8
10 11
7 8
10 11
14 15
10 11
14 15
21 22
14 15
21 22
21 22
R 2000 1 2 2 3 3 4 5 6 7 8 10 11 14 15 21 22
= Use first sampling plan below arrow. If sample size equals or exceeds lot or batch size, do 100 percent inspection. Ac = Acceptance number.
= Use first sampling plan above arrow. Re = Rejection number.
7/27/2019 Table Mil Std 105e
6/19
3
Table II - B. Single Sampling Plans for Tightened Inspection (Master Table).
Samplesizecodeletter
Samplesize
Acceptable Quality Levels (tightened inspection)
0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0 1.5 2.5 4.0 6.5 10 15 25 40 65 100 150 250 400 650 1000
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
A
B
C
2
3
5 0 1
0 1
1 2
1 2
2 3
1 2
2 3
3 4
2 3
3 4
5 6
3 4
5 6
8 9
5 6
8 9
12 13
8 9
12 13
18 19
12 13
18 19
27 28
18 19
27 28
41 42
27 28
41 42
D
E
F
8
13
20 0 1
0 1
0 1
1 2
1 2
2 3
1 2
2 3
3 4
2 3
3 4
5 6
3 4
5 6
8 9
5 6
8 9
12 13
8 9
12 13
18 19
12 13
18 19
18 19
27 28
27 28
41 42
41 42
G
H
J
32
50
80 0 1
0 1
0 1
1 2
1 2
2 3
1 2
2 3
3 4
2 3
3 4
5 6
3 4
5 6
8 9
5 6
8 9
12 13
8 9
12 13
18 19
12 13
18 19
18 19
K
L
M
125
200
315 0 1
0 1
0 1
1 2
1 2
2 3
1 2
2 3
3 4
2 3
3 4
5 6
3 4
5 6
8 9
5 6
8 9
12 13
8 9
12 13
18 19
12 13
18 19
18 19
N
P
Q
500
800
1250 0 1
0 1
0 1
1 2
1 2
2 3
1 2
2 3
3 4
2 3
3 4
5 6
3 4
5 6
8 9
5 6
8 9
12 13
8 9
12 13
18 19
12 13
18 19
18 19
R
S
2000
3150
0 1
1 2
1 2 2 3 3 4 5 6 8 9 12 13 18 19
= Use first sampling plan below arrow. If sample size equals or exceeds lot or batch size, do 100 percent inspection. Ac = Acceptance number.= Use first sampling plan above arrow. Re = Rejection number.
7/27/2019 Table Mil Std 105e
7/19
Table II - C. Single Sampling Plans for Reduced Inspection (Master Table).
Samplesizecodeletter
Samplesize
Acceptable Quality Levels (reduced inspection)
0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0 1.5 2.5 4.0 6.5 10 15 25 40 65 100 150 250 400 650 1000
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
A
B
C
2
2
2 0 1
0 1
0 1
0 2
0 2
1 3
1 2
1 3
1 4
2 3
2 4
2 5
3 4
3 5
3 6
5 6
5 6
5 8
7 8
7 8
7 10
10 11
10 11
10 13
14 15
14 15
14 17
21 22
21 22
21 24
30 31
30 31
D
E
F
3
5
8 0 1
0 1
0 1
0 2
0 2
1 3
0 2
1 3
1 4
1 3
1 4
2 5
1 4
2 5
3 6
2 5
3 6
5 8
3 6
5 8
7 10
5 8
7 10
10 13
7 10
10 13
10 13
14 17
14 17
21 24
21 24
G
H
J
13
20
32 0 1
0 1
0 1
0 2
0 2
1 3
0 2
1 3
1 4
1 3
1 4
2 5
1 4
2 5
3 6
2 5
3 6
5 8
3 6
5 8
7 10
5 8
7 10
10 13
7 10
10 13
10 13
K
L
M
50
80
125 0 1
0 1
0 1
0 2
0 2
1 3
0 2
1 3
1 4
1 3
1 4
2 5
1 4
2 5
3 6
2 5
3 6
5 8
3 6
5 8
7 10
5 8
7 10
10 13
7 10
10 13
10 13
N
P
Q
200
315
500 0 1
0 1
0 1
0 2
0 2
1 3
0 2
1 3
1 4
1 3
1 4
2 5
1 4
2 5
3 6
2 5
3 6
5 8
3 6
5 8
7 10
5 8
7 10
10 13
7 10
10 13
10 13
R 800 0 2 1 3 1 4 2 5 3 6 5 8 7 10 10 13
= Use first sampling plan below arrow. If sample size equals or exceeds lot or batch size, do 100 percent inspection. Ac = Acceptance number.
= Use first sampling plan above arrow. Re = Rejection number.
= If the acceptance number has been exceeded, but the rejection number has not been reached; accept the lot, but reinstate normal inspection.
7/27/2019 Table Mil Std 105e
8/19
Table III - A. Double Sampling Plans for Normal Inspection (Master Table).
Samplesizecodeletter
SampleSample
size
Cumulative
samplesize
Acceptable Quality Levels (normal inspection)
0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0 1.5 2.5 4.0 6.5 10 15 25 40 65 100 150 250 400 650 10
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac
A
B First
Second
2
2
2
4
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
8 9
5 9
12 13
7 11
18 19
11 16
26 27
17 22
37 38
25
56C First
Second
3
3
3
6
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
8 9
5 9
12 13
7 11
18 19
11 16
26 27
17 22
37 38
25 31
56 57
D First
Second
5
5
5
10
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
8 9
5 9
12 13
7 11
18 19
11 16
26 27
17 22
37 38
25 31
56 57
E First
Second
8
8
8
16
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
8 9
5 9
12 13
7 11
18 19
11 16
26 27
17 22
37 38
25 31
56 57
F First
Second
13
13
13
26
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
8 9
5 9
12 13
7 11
18 19
11 16
26 27
G First
Second
20
20
20
40
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
8 9
5 9
12 13
7 11
18 19
11 16
26 27
H First
Second
32
32
32
64
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
8 9
5 9
12 13
7 11
18 19
11 16
26 27
J FirstSecond
5050
50100
0 21 2
0 33 4
1 44 5
2 56 7
3 78 9
5 912 13
7 1118 19
11 1626 27
K First
Second
80
80
80
160
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
8 9
5 9
12 13
7 11
18 19
11 16
26 27
L First
Second
125
125
125
250
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
8 9
5 9
12 13
7 11
18 19
11 16
26 27
M First
Second
200
200
200
400
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
8 9
5 9
12 13
7 11
18 19
11 16
26 27
N First
Second
315
315
315
630
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
8 9
5 9
12 13
7 11
18 19
11 16
26 27
P First
Second
500
500
500
1000
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
8 9
5 9
12 13
7 11
18 19
11 16
26 27
Q First
Second
800
800
800
1600
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
8 9
5 9
12 13
7 11
18 19
11 16
26 27R First
Second
1250
1250
1250
2500
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
8 9
5 9
12 13
7 11
18 19
11 16
26 27
= Use first sampling plan below arrow. If sample size equals or exceeds lot or batch size, do 100 percent inspection. Ac = Acceptance number.
= Use first sampling plan above arrow. Re = Rejection number.
= Use corresponding single sampling plan (or alternatively, use double sampling plan below, where available).
7/27/2019 Table Mil Std 105e
9/19
Table III - B. Double Sampling Plans for Tightened Inspection (Master Table).
Samplesizecodeletter
SampleSample
size
Cumulative
samplesize
Acceptable Quality Levels (normal inspection)
0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0 1.5 2.5 4.0 6.5 10 15 25 40 65 100 150 250 400 650 10
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac
A
B First
Second
2
2
2
4
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
11 12
6 10
15 16
9 14
23 24
15 20
34 35
23
52
C First
Second
3
3
3
6
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
11 12
6 10
15 16
9 14
23 24
15 20
34 35
23 29
52 53
D First
Second
5
5
5
10
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
11 12
6 10
15 16
9 14
23 24
15 20
34 35
23 29
52 53
E First
Second
8
8
8
16
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
11 12
6 10
15 16
9 14
23 24
15 20
34 35
23 29
52 53
F First
Second
13
13
13
26
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
11 12
6 10
15 16
9 14
23 24
G First
Second
20
20
20
40
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
11 12
6 10
15 16
9 14
23 24
H First
Second
32
32
32
64
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
11 12
6 10
15 16
9 14
23 24
J First
Second
50
50
50
100
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
11 12
6 10
15 16
9 14
23 24
K First
Second
80
80
80
160
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
11 12
6 10
15 16
9 14
23 24
L First
Second
125
125
125
250
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
11 12
6 10
15 16
9 14
23 24
M First
Second
200
200
200
400
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
11 12
6 10
15 16
9 14
23 24
N First
Second
315
315
315
630
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
11 12
6 10
15 16
9 14
23 24
P First
Second
500
500
500
1000
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
11 12
6 10
15 16
9 14
23 24
Q First
Second
800
800
800
1600
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
11 12
6 10
15 16
9 14
23 24
R First
Second
1250
1250
1250
2500
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
11 12
6 10
15 16
9 14
23 24
S First
Second
2000
2000
2000
4000
0 2
1 2
= Use first sampling plan below arrow. If sample size equals or exceeds lot or batch size, do 100 percent inspection. Ac = Acceptance number.
= Use first sampling plan above arrow. Re = Rejection number. = Use corresponding single sampling plan (or alternatively, use double sampling plan below, where available).
7/27/2019 Table Mil Std 105e
10/19
Table III - C. Double Sampling Plans for Reduced Inspection (Master Table).
Samplesizecodeletter
SampleSample
size
Cumulative
samplesize
Acceptable Quality Levels (reduced inspection)
0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0 1.5 2.5 4.0 6.5 10 15 25 40 65 100 150 250 400 650 10
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac
A
B
C
D First
Second
2
2
2
4
0 2
0 2
0 3
0 4
0 4
1 5
0 4
3 6
1 5
4 7
2 7
6 9
3 8
8 12
5 10
12 16
7 12
18 22
11 17
26 30
E First
Second
3
3
3
6
0 2
0 2
0 3
0 4
0 4
1 5
0 4
3 6
1 5
4 7
2 7
6 9
3 8
8 12
5 10
12 16
7 12
18 22
11 17
26 30
F First
Second
5
5
5
10
0 2
0 2
0 3
0 4
0 4
1 5
0 4
3 6
1 5
4 7
2 7
6 9
3 8
8 12
5 10
12 16
G First
Second
8
8
8
16
0 2
0 2
0 3
0 4
0 4
1 5
0 4
3 6
1 5
4 7
2 7
6 9
3 8
8 12
5 10
12 16
H First
Second
13
13
13
26
0 2
0 2
0 3
0 4
0 4
1 5
0 4
3 6
1 5
4 7
2 7
6 9
3 8
8 12
5 10
12 16
J First
Second
20
20
20
40
0 2
0 2
0 3
0 4
0 4
1 5
0 4
3 6
1 5
4 7
2 7
6 9
3 8
8 12
5 10
12 16
K First
Second
32
32
32
64
0 2
0 2
0 3
0 4
0 4
1 5
0 4
3 6
1 5
4 7
2 7
6 9
3 8
8 12
5 10
12 16
L FirstSecond
5050
50100
0 20 2
0 30 4
0 41 5
0 43 6
1 54 7
2 76 9
3 88 12
5 1012 16
M First
Second
80
80
80
160
0 2
0 2
0 3
0 4
0 4
1 5
0 4
3 6
1 5
4 7
2 7
6 9
3 8
8 12
5 10
12 16
N First
Second
125
125
125
250
0 2
0 2
0 3
0 4
0 4
1 5
0 4
3 6
1 5
4 7
2 7
6 9
3 8
8 12
5 10
12 16
P First
Second
200
200
200
400
0 2
0 2
0 3
0 4
0 4
1 5
0 4
3 6
1 5
4 7
2 7
6 9
3 8
8 12
5 10
12 16
Q First
Second
315
315
315
630
0 2
0 2
0 3
0 4
0 4
1 5
0 4
3 6
1 5
4 7
2 7
6 9
3 8
8 12
5 10
12 16
R First
Second
500
500
500
1000
0 2
0 2
0 3
0 4
0 4
1 5
0 4
3 6
1 5
4 7
2 7
6 9
3 8
8 12
5 10
12 16
= Use first sampling plan below arrow. If sample size equals or exceeds lot or batch size, do 100 percent inspection.
= Use first sampling plan above arrow.
Ac = Acceptance number.
Re = Rejection number.
= Use corresponding single sampling plan (or alternatively, use double sampling plan below, where available).
= If, after the second sample, the acceptance number has been exceeded, but the rejection number has not been reached, accept the lot, but reinstate normal inspection.
7/27/2019 Table Mil Std 105e
11/19
Table IV- A. Multiple Sampling Plans for Normal Inspection (Master Table).
Samplesizecodeletter
SampleSample
size
Cumulative
samplesize
Acceptable Quality Levels (normal inspection)
0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0 1.5 2.5 4.0 6.5 10 15 25 40 65 100 150 250 400 650 10
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac
ABC
++++++
++++
++++
++++
++++
++++
++++
++++
++++
+
D FirstSecondThird
FourthFifthSixthSeventh
222
2222
246
8101214
# 2# 20 2
0 31 31 32 3
# 20 30 3
1 42 43 54 5
# 30 31 4
2 53 64 66 7
# 41 52 6
3 75 87 99 10
0 41 63 8
5 107 11
10 1213 14
0 53 86 10
8 1311 1514 1718 19
1 74 108 13
12 1717 2021 2325 26
2 97 14
13 19
19 2525 2931 3337 38
4 1211 1919 27
27 3436 4045 4753 54
6 1617 2729 39
40 4953 5865 6877 78
E FirstSecondThirdFourthFifthSixthSeventh
3333333
36912151821
# 2# 20 20 31 31 32 3
# 20 30 31 42 43 54 5
# 30 31 42 53 64 66 7
# 41 52 63 75 87 99 10
0 41 63 85 107 11
10 1213 14
0 53 86 108 13
11 1514 1718 19
1 74 108 13
12 1717 2021 2325 26
2 97 14
13 1919 2525 2931 3337 38
4 1211 1919 2727 3436 4045 4753 54
6 1617 2729 3940 4953 5865 6877 78
F FirstSecondThirdFourthFifthSixthSeventh
5555555
5101520253035
# 2# 20 20 31 31 32 3
# 20 30 31 42 43 54 5
# 30 31 42 53 64 66 7
# 41 52 63 75 87 99 10
0 41 63 85 107 11
10 1213 14
0 53 86 108 13
11 1514 1718 19
1 74 108 13
12 1717 2021 2325 26
2 97 14
13 1919 2525 2931 3337 38
G FirstSecondThirdFourthFifthSixthSeventh
8888888
8162432404856
# 2# 20 20 31 31 32 3
# 20 30 31 42 43 54 5
# 30 31 42 53 64 66 7
# 41 52 63 75 87 99 10
0 41 63 85 107 11
10 1213 14
0 53 86 108 13
11 1514 1718 19
1 74 108 13
12 1717 2021 2325 26
2 97 14
13 1919 2525 2931 3337 38
H FirstSecondThirdFourthFifthSixthSeventh
13131313131313
13263952657891
# 2# 20 20 31 31 32 3
# 20 30 31 42 43 54 5
# 30 31 42 53 64 66 7
# 41 52 63 75 87 99 10
0 41 63 85 107 11
10 1213 14
0 53 86 108 13
11 1514 1718 19
1 74 108 13
12 1717 2021 2325 26
2 97 14
13 1919 2525 2931 3337 38
J FirstSecondThird
FourthFifthSixthSeventh
202020
20202020
204060
80100120140
# 2# 20 2
0 31 31 32 3
# 20 30 3
1 42 43 54 5
# 30 31 4
2 53 64 66 7
# 41 52 6
3 75 87 99 10
0 41 63 8
5 107 1110 1213 14
0 53 86 10
8 1311 1514 1718 19
1 74 108 13
12 1717 2021 2325 26
2 97 14
13 19
19 2525 2931 3337 38
= Use first sampling plan below arrow (refer to continuation of table on following page, when necessary). If sample size equals or exceeds lot or batch size, do 100 percent inspection. = Use first sampling plan above ar
= Use corresponding single sampling plan (or alternatively, use double sampling plan below, where available). Ac = Acceptance number. Re = Rejection number.++ = Use corresponding double sampling plan (or alternatively, use multiple sampling plan below, where available). # = Acceptance not permitted at this sample size.
7/27/2019 Table Mil Std 105e
12/19
Table IV- A. (continued).Sample
sizecodeletter
SampleSample
size
Cumulative
samplesize
Acceptable Quality Levels (norm
0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0 1.5 2.5 4.0
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re A
K FirstSecond
ThirdFourthFifthSixthSeventh
3232
3232323232
3264
96128160192224
# 2# 2
0 20 31 31 32 3
# 20 3
0 31 42 43 54 5
# 30 3
1 42 53 64 66 7
# 41 5
2 63 75 87 99 10
0 41 6
3 85 107 11
10 1213 14
0 53 8
6 108 1311 1514 1718 19
1122
L FirstSecondThirdFourthFifthSixthSeventh
50505050505050
50100150200250300350
# 2# 20 20 31 31 32 3
# 20 30 31 42 43 54 5
# 30 31 42 53 64 66 7
# 41 52 63 75 87 99 10
0 41 63 85 107 11
10 1213 14
0 53 86 108 13
11 1514 1718 19
1 74 108 13
12 1717 2021 2325 26
11233
M FirstSecondThirdFourthFifthSixthSeventh
80808080808080
80160240320400480560
# 2# 20 20 31 31 32 3
# 20 30 31 42 43 54 5
# 30 31 42 53 64 66 7
# 41 52 63 75 87 99 10
0 41 63 85 107 11
10 1213 14
0 53 86 108 13
11 1514 1718 19
1 74 108 13
12 1717 2021 2325 26
2 97 14
13 1919 2525 2931 3337 38
N FirstSecondThirdFourth
FifthSixthSeventh
125125125125
125125125
125250375500
625750875
# 2# 20 20 3
1 31 32 3
# 20 30 31 4
2 43 54 5
# 30 31 42 5
3 64 66 7
# 41 52 63 7
5 87 99 10
0 41 63 85 10
7 1110 1213 14
0 53 86 108 13
11 1514 1718 19
1 74 108 13
12 17
17 2021 2325 26
2 97 14
13 1919 25
25 2931 3337 38
P FirstSecondThirdFourthFifthSixth
200200200200200200
20040060080010001200
# 2# 20 20 31 31 3
# 20 30 31 42 43 5
# 30 31 42 53 64 6
# 41 52 63 75 87 9
0 41 63 85 107 11
10 12
0 53 86 108 13
11 1514 17
1 74 108 13
12 1717 2021 23
2 97 14
13 1919 2525 2931 33
7/27/2019 Table Mil Std 105e
13/19
Table IV- B. Multiple Sampling Plans for Tightened Inspection (Master Table).
Samplesizecodeletter
SampleSample
size
Cumulative
samplesize
Acceptable Quality Levels (tightened inspection)
0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0 1.5 2.5 4.0 6.5 10 15 25 40 65 100 150 250 400 650 10
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac
ABC
++
++++
++++
++++
++++
++++
++++
++++
++++
+
D FirstSecondThirdFourthFifthSixthSeventh
2222222
2468101214
# 2# 20 20 31 31 32 3
# 20 30 31 42 43 54 5
# 30 31 42 53 64 66 7
# 41 52 63 75 87 99 10
0 42 74 96 119 12
12 1414 15
0 63 97 12
10 1514 1718 2021 22
1 86 12
11 1716 2222 2527 2932 33
3 1010 1717 2424 3132 3740 4348 49
6 1516 2526 3637 4649 5561 6472 73
E FirstSecondThirdFourthFifthSixthSeventh
3333333
36912151821
# 2# 20 20 31 31 32 3
# 20 30 31 42 43 54 5
# 30 31 42 53 64 66 7
# 41 52 63 75 87 99 10
0 42 74 96 119 12
12 1414 15
0 63 97 12
10 1514 1718 2021 22
1 86 12
11 1716 2222 2527 2932 33
3 1010 1717 2424 3132 3740 4348 49
6 1516 2526 3637 4649 5561 6472 73
F FirstSecondThirdFourthFifthSixthSeventh
5555555
5101520253035
# 2# 20 20 31 31 32 3
# 20 30 31 42 43 54 5
# 30 41 42 53 64 66 7
# 41 52 63 75 87 99 10
0 42 74 96 119 12
12 1414 15
0 63 97 12
10 1514 1718 2021 22
1 86 12
11 1716 2222 2527 2932 33
G FirstSecondThirdFourthFifthSixthSeventh
8888888
8162432404856
# 2# 20 20 31 31 32 3
# 20 30 31 42 43 54 5
# 30 41 42 53 64 66 7
# 41 52 63 75 87 99 10
0 42 74 96 119 12
12 1414 15
0 63 97 12
10 1514 1718 2021 22
1 86 12
11 1716 2222 2527 2932 33
H FirstSecondThirdFourthFifthSixthSeventh
13131313131313
13263952657891
# 2# 20 20 31 31 32 3
# 20 30 31 42 43 54 5
# 30 41 42 53 64 66 7
# 41 52 63 75 87 99 10
0 42 74 96 119 12
12 1414 15
0 63 97 12
10 1514 1718 2021 22
1 86 12
11 1716 2222 2527 2932 33
J FirstSecondThirdFourth
FifthSixthSeventh
20202020
202020
20406080
100120140
# 2# 20 20 3
1 31 32 3
# 20 30 31 4
2 43 54 5
# 30 41 42 5
3 64 66 7
# 41 52 63 7
5 87 99 10
0 42 74 96 11
9 1212 1414 15
0 63 97 12
10 15
14 1718 2021 22
1 86 12
11 1716 22
22 2527 2932 33
= Use first sampling plan below arrow (refer to continuation of table on following page, when necessary). If sample size equals or exceeds lot or batch size, do 100 percent inspection. = Use first sampling plan above ar
= Use corresponding single sampling plan (or alternatively, use double sampling plan below, where available). Ac = Acceptance number. Re = Rejection number.++ = Use corresponding double sampling plan (or alternatively, use multiple sampling plan below, where available). # = Acceptance not permittedat this sample size.
7/27/2019 Table Mil Std 105e
14/19
Table IV- B. (continued).
Samplesizecodeletter
SampleSample
size
Cumulative
samplesize
Acceptable Quality Levels (tightened inspection)
0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0 1.5 2.5 4.0 6.5 10 15 25 40 65 100 150 250 400 650 10
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac
K FirstSecondThirdFourthFifthSixthSeventh
32323232323232
326496128160192224
# 2# 20 20 31 31 32 3
# 20 30 31 42 43 54 5
# 30 41 42 53 64 66 7
# 41 52 63 75 87 99 10
0 42 74 96 119 12
12 1414 15
0 63 97 12
10 1514 1718 2021 22
1 86 12
11 1716 2222 2527 2932 33
L FirstSecondThirdFourthFifthSixthSeventh
50505050505050
50100150200250300350
# 2# 20 20 31 31 32 3
# 20 30 31 42 43 54 5
# 30 41 42 53 64 66 7
# 41 52 63 75 87 99 10
0 42 74 96 119 12
12 1414 15
0 63 97 12
10 1514 1718 2021 22
1 86 12
11 1716 2222 2527 2932 33
M FirstSecondThirdFourthFifthSixthSeventh
80808080808080
80160240320400480560
# 2# 20 20 31 31 32 3
# 20 30 31 42 43 54 5
# 30 41 42 53 64 66 7
# 41 52 63 75 87 99 10
0 42 74 96 119 12
12 1414 15
0 63 97 12
10 1514 1718 2021 22
1 86 12
11 1716 2222 2527 2932 33
N FirstSecondThirdFourthFifthSixthSeventh
125125125125125125125
125250375500625750875
# 2# 20 20 31 31 32 3
# 20 30 31 42 43 54 5
# 30 41 42 53 64 66 7
# 41 52 63 75 87 99 10
0 42 74 96 119 12
12 1414 15
0 63 97 12
10 1514 1718 2021 22
1 86 12
11 1716 2222 2527 2932 33
P FirstSecondThirdFourthFifthSixthSeventh
200200200200200200200
200400600800
100012001400
# 2# 20 20 31 31 32 3
# 20 30 31 42 43 54 5
# 30 41 42 53 64 66 7
# 41 52 63 75 87 99 10
0 42 74 96 119 12
12 1414 15
0 63 97 12
10 1514 1718 2021 22
1 86 12
11 1716 2222 2527 2932 33
Q FirstSecondThirdFourthFifthSixthSeventh
315315315315315315315
315630945
1260157518902205
# 2# 20 20 31 31 32 3
# 20 30 31 42 43 54 5
# 30 41 42 53 64 66 7
# 41 52 63 75 87 99 10
0 42 74 96 119 12
12 1414 15
0 63 97 12
10 1514 1718 2021 22
1 86 12
11 1716 2222 2527 2932 33
R FirstSecondThirdFourthFifth
SixthSeventh
500500500500500
500500
5001000150020002500
30003500
# 2# 20 20 31 3
1 32 3
# 20 30 31 42 4
3 54 5
# 30 41 42 53 6
4 66 7
# 41 52 63 75 8
7 99 10
0 42 74 96 119 12
12 1414 15
0 63 97 12
10 1514 17
18 2021 22
1 86 12
11 1716 2222 25
27 2932 33
S FirstSecondThirdFourthFifthSixthSeventh
800800800800800800800
800160024003200400048005600
# 2# 20 20 31 31 32 3
7/27/2019 Table Mil Std 105e
15/19
Table IV- C. Multiple Sampling Plans for Reduced Inspection (Master Table).
Samplesizecodeletter
SampleSample
size
Cumulative
samplesize
Acceptable Quality Levels (reduced inspection)
0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0 1.5 2.5 4.0 6.5 10 15 25 40 65 100 150 250 400 650 10
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac
ABCDE
++
++++
++++
++++
++++
++++
++++
++++
++++
++++
++
F FirstSecondThirdFourthFifthSixthSeventh
2222222
2468101214
# 2# 20 20 30 30 31 3
# 2# 30 30 40 41 51 5
# 3# 30 40 51 61 62 7
# 30 40 51 62 73 74 8
# 40 51 62 73 84 96 10
# 41 62 83 105 117 129 14
0 51 73 95 127 13
10 1513 17
0 63 96 128 15
11 1714 2018 22
G FirstSecondThirdFourthFifthSixthSeventh
3333333
36912151821
# 2# 20 20 30 30 31 3
# 2# 30 30 40 41 51 5
# 3# 30 40 51 61 62 7
# 30 40 51 62 73 74 8
# 40 51 62 73 84 96 10
# 41 62 83 105 117 129 14
0 51 73 95 127 13
10 1513 17
0 63 96 128 15
11 1714 2018 22
H FirstSecondThirdFourthFifthSixthSeventh
5555555
5101520253035
# 2# 20 20 30 30 31 3
# 2# 30 30 40 41 51 5
# 3# 30 40 51 61 62 7
# 30 40 51 62 73 74 8
# 40 51 62 73 84 96 10
# 41 62 83 105 117 129 14
0 51 73 95 127 13
10 1513 17
0 63 96 128 15
11 1714 2018 22
J FirstSecondThirdFourthFifthSixthSeventh
8888888
8162432404856
# 2# 20 20 30 30 31 3
# 2# 30 30 40 41 51 5
# 3# 30 40 51 61 62 7
# 30 40 51 62 73 74 8
# 40 51 62 73 84 96 10
# 41 62 83 105 117 129 14
0 51 73 95 127 13
10 1513 17
0 63 96 128 15
11 1714 2018 22
K FirstSecondThirdFourthFifth
SixthSeventh
1313131313
1313
1326395265
7891
# 2# 20 20 30 3
0 31 3
# 2# 30 30 40 4
1 51 5
# 3# 30 40 51 6
1 62 7
# 30 40 51 62 7
3 74 8
# 40 51 62 73 8
4 96 10
# 41 62 83 105 11
7 129 14
0 51 73 95 127 13
10 1513 17
0 63 96 128 15
11 17
14 2018 22
= Use first sampling plan below arrow (refer to continuation of table on following page, when necessary). If sample size equals or exceeds lot or batch size, do 100 percent inspection. = Use first sampling plan above ar
= Use corresponding single sampling plan (or alternatively, use double sampling plan below, where available). Ac = Acceptance number. Re = Rejection number.++ = Use corresponding double sampling plan (or alternatively, use multiple sampling plan below, where available). # = Acceptance not permitted at this sample size. = If, after the final sample, the acceptance number has been exceeded but the rejection number has not been reached, accept the lot but reinstate normal inspection.
7/27/2019 Table Mil Std 105e
16/19
Table IV- C. (continued).
Samplesizecodeletter
SampleSample
size
Cumulative
samplesize
Acceptable Quality Levels (reduced inspection)
0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0 1.5 2.5 4.0 6.5 10 15 25 40 65 100 150 250 400 650 10
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac
L FirstSecondThirdFourthFifthSixthSeventh
20202020202020
20406080
100120140
# 2# 20 20 30 30 31 3
# 2# 30 30 40 41 51 5
# 3# 30 40 51 61 62 7
# 30 40 51 62 73 74 8
# 40 51 62 73 84 96 10
# 41 62 83 105 117 129 14
0 51 73 95 127 13
10 1513 17
0 63 96 128 15
11 1714 2018 22
M FirstSecondThirdFourthFifthSixthSeventh
32323232323232
326496
128160192224
# 2# 20 20 30 30 31 3
# 2# 30 30 40 41 51 5
# 3# 30 40 51 61 62 7
# 30 40 51 62 73 74 8
# 40 51 62 73 84 96 10
# 41 62 83 105 117 129 14
0 51 73 95 127 13
10 1513 17
0 63 96 128 15
11 1714 2018 22
N FirstSecondThirdFourthFifthSixthSeventh
50505050505050
50100150200250300350
# 2# 20 20 30 30 31 3
# 2# 30 30 40 41 51 5
# 3# 30 40 51 61 62 7
# 30 40 51 62 73 74 8
# 40 51 62 73 84 96 10
# 41 62 83 105 117 129 14
0 51 73 95 127 13
10 1513 17
0 63 96 128 15
11 1714 2018 22
P FirstSecond
ThirdFourthFifthSixthSeventh
8080
8080808080
80160
240320400480560
# 2# 2
0 20 30 30 31 3
# 2# 3
0 30 40 41 51 5
# 3# 3
0 40 51 61 62 7
# 30 4
0 51 62 73 74 8
# 40 5
1 62 73 84 96 10
# 41 6
2 83 105 117 129 14
0 51 7
3 95 127 13
10 1513 17
0 63 9
6 128 15
11 1714 2018 22
Q FirstSecondThirdFourthFifthSixthSeventh
125125125125125125125
125250375500625750875
# 2# 20 20 30 30 31 3
# 2# 30 30 40 41 51 5
# 3# 30 40 51 61 62 7
# 30 40 51 62 73 74 8
# 40 51 62 73 84 96 10
# 41 62 83 105 117 129 14
0 51 73 95 127 13
10 1513 17
0 63 96 128 15
11 1714 2018 22
R FirstSecondThirdFourthFifth
SixthSeventh
200200200200200
200200
200400600800
1000
12001400
# 2# 20 20 30 3
0 31 3
# 2# 30 30 40 4
1 51 5
# 3# 30 40 51 6
1 62 7
# 30 40 51 62 7
3 74 8
# 40 51 62 73 8
4 96 10
# 41 62 83 105 11
7 129 14
0 51 73 95 127 13
10 1513 17
0 63 96 128 15
11 17
14 2018 22
= Use first sampling plan below arrow (refer to continuation of table on following page, when necessary). If sample size equals or exceeds lot or batch size, do 100 percent inspection. = Use first sampling plan above ar
= Use corresponding single sampling plan (or alternatively, use double sampling plan below, where available). Ac = Acceptance number. Re = Rejection number.++ = Use corresponding double sampling plan (or alternatively, use multiple sampling plan below, where available). # = Acceptance not permitted at this sample size. = If, after the final sample, the acceptance number has been exceeded but the rejection number has not been reached, accept the lot but reinstate normal inspection.
7/27/2019 Table Mil Std 105e
17/19
Table V-A. Average Outgoing Quality Limit Factors for Normal Inspection (Single Sampling) *
CodeLetter
Samplesize
Acceptable Quality Level
0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0 1.5 2.5 4.0 6.5 10 15 25 40 65 100 150 250 400 650 1
A
B
C
2
3
5 7.4
12
18
17
28
27
42
46
39
69
65
63
97
110
90
160
150
130
220
220
190
330
310
290
470
490
430
730
720
660
1
1
D
E
F
8
13
20 1.8
2.8
4.6
4.2
6.5
6.9
11
11
9.7
17
15
16
24
24
22
40
34
33
56
50
47
82
72
73
120
110
180
170
270
250
410
G
H
J
32
50
80 0.46
0.74
1.2
1.1
1.7
1.7
2.6
2.7
2.4
4.3
3.9
4.0
6.1
6.3
5.6
9.9
9.0
8.2
14
13
12
21
19
18
29
29
46
K
L
M
125
200
315 0.12
0.18
0.29
0.27
0.42
0.44
0.67
0.69
0.62
1.1
0.97
1.00
1.6
1.6
1.4
2.5
2.2
2.1
3.6
3.3
3.0
5.2
4.7
4.7
7.5
7.3
12
N
P
Q
500
800
1250 0.029
0.046
0.074
0.067
0.11
0.11
0.17
0.17
0.16
0.27
0.24
0.25
0.39
0.40
0.36
0.63
0.56
0.52
0.90
0.82
0.75
1.3
1.2
1.2
1.9
1.8
2.9
R 2000 0.042 0.069 0.097 0.16 0.22 0.33 0.47 0.73
* Note: For the exact AOQL, the above volume must be multiplied by
sizeBatchorLot
sizeSample1
7/27/2019 Table Mil Std 105e
18/19
Table V-B. Average Outgoing Quality Limit Factors for Tightened Inspection (Single Sampling) *
CodeLetter
Samplesize
Acceptable Quality Level
0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0 1.5 2.5 4.0 6.5 10 15 25 40 65 100 150 250 400 650 1
A
B
C
2
3
5 7.4
12
17
28
27
42
46
39
69
65
63
97
110
100
160
170
160
260
270
250
400
410
390
620
650
610
1
D
E
F
8
13
20 1.8
2.8
4.6
4.2
6.5
6.9
11
11
9.7
17
15
16
24
24
26
40
40
40
64
61
62
99
95
160
150
240
240
380
G
H
J
32
50
80 0.46
0.74
1.2
1.1
1.7
1.7
2.6
2.7
2.4
4.3
3.9
4.0
6.1
6.3
6.4
9.9
10
9.9
16
16
16
25
25
39
K
L
M
125
200
315 0.12
0.18
0.29
0.27
0.42
0.44
0.67
0.69
0.62
1.1
0.97
1.0
1.6
1.6
1.6
2.5
2.6
2.5
4.1
4.0
3.9
6.4
6.2
9.9
N
P
Q
500
800
1250 0.029
0.046
0.074
0.067
0.11
0.11
0.17
0.17
0.16
0.27
0.24
0.25
0.39
0.40
0.41
0.63
0.64
0.64
1.0
0.99
0.99
1.6
1.6
2.5
R
S
2000
3150
0.018
0.027
0.042 0.069 0.097 0.16 0.26 0.40 0.62
* Note: For the exact AOQL, the above volume must be multiplied by
sizeBatchorLot
sizeSample1
7/27/2019 Table Mil Std 105e
19/19
Table VIII. Limit Numbers for Reduced Inspection.
Number ofsample units
Acceptable Quality Level
from last 10lots or batches 0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0 1.5 2.5 4.0 6.5 10 15 25 40 65 100 150 250 400 650 1
20- 2930- 49
50- 79
0
0
0
00
2
01
3
23
7
47
14
813
25
1422
40
2236
63
4063
110
68105
181
115178
301
12
80- 129130 - 199200 - 319
0
00
002
024
248
4714
71322
142540
244268
4272115
68115181
105177277
181301471
297490
320- 499500- 799800 - 1249
0
00
002
024
137
4714
81424
142542
244068
3963105
68110181
113181
189
1250- 19992000- 31493150- 4999
0
00
001
024
248
4814
71424
132238
244067
4068111
69115186
110181
169
5000- 79998000- 1249912500- 19999
0
00
002
024
247
3713
71424
142440
254269
4068110
63105169
110181
181
20000- 3149931500- 4999950000 & over
002
013
247
4814
81425
142440
223863
4067110
68111181
115186301
181
Denotes that the number of sample units from the last ten lots or batches is not sufficient for reduced inspection for this AQL. In this instance more than ten lots or batches may be used for the calculation, provided that the lots
batches used are the most recent ones in sequence, that they have all been on normal inspection, and that none has been rejected while on original inspection.