Post on 04-Feb-2022
TEKA ILLUMINATION, INC 40429 Brickyard Drive Madera, California 93636 (559) 438-5800 Fax (559) 438-5900 www.tekaillumination.com
TEKAI L L U M I N A T I O N
© Copyright TEKA 2004
Materials and ConstructionA. Cast bronze cap B. Stainless steel or copper on stainless steel Ring baffles C. Machined, solid brass spacers D. Heavy wall, .125 thk. solid copper post, 3.5" O.D. E. Etched glass cylinder F. Cast bronze housing G. Cast bronze base H. Solid copper, heavy wall shade I. Stainless steel and cast bronze anchor plate J. Provided with all stainless steel fasteners K. 120V electronic PLT ballast with -15°F starting temperature is standard on PLC models
DescriptionExterior bollard luminaire.
T-57 Beacon Shaded Bollard
Product Number Lamp Rings Finish OptionBSB-2546 / Natural 60W A-19 St. Stl. Brown PatinaBSB-2516/ Natural 60W A-19 Copper Brown PatinaBSB-2542 / Natural 26W PLT St. Stl. Brown PatinaBSB-2512/ Natural 26W PLT Copper Brown Patina
MountingTEKA mounting kit #34 provided. Allows for (2) 3⁄4" maximum trade conduits.
Options available at additional cost1. Add suffix BP for brown patina 2. Add suffix # 277 to PLT models for integral 277V electronic ballast 3. For higher or lower heights available, consult factory
HE
12"
C
D
G
6"31⁄8"
5"
8"
AB
F
40"
Note ETL Listed to ANSI/UL Standard 1598 and Certified to CAN/CSA Standard C22.2 No. 250
All dimensions are inches (centimeters) unless otherwise indicated.*Weight as configured in example below.
OUTDOOR WSTM-CF
Catalog Number
Notes
Type
ORDERING INFORMATION For shortest lead times, configure product using standard options (shown in bold). Example: WSTM 32TRT MD MVOLT DNAT LPI
WSTM MD
Series Wattage Distribution Voltage Ballast Mounting Options Finish5 Lamp7
WSTM 26DTT26TRT32TRT42TRT
MD Medium throw
120277347MVOLT1
(blank) Electronic 0° F (blank) Surface mount
Shipped separately2
UT5 Uptilt 5 degrees
Shipped installed in fixtureGMF Internal slow-blow fusing3
PE Photoelectric cellbutton type3,4
DFL Diffusing lensCSA CSA certifiedNOM NOM certifiedShipped separately4
WG Wireguard
(blank) Dark bronze, textured DSST Sandstone, texturedDNAT Natural aluminum,
texturedDWHG White, texturedDBLB Black, texturedCR Corrosion-resistanceCRT Non-stick protective
coating6
StripingSDDB Dark bronzeSDWH WhiteSDBL BlackSDNA Natural aluminumSDTG Tennis greenSDBR Bright redSDBUA Dark blueSDGYM GraySDYLB Yellow
LPI Lamp included
L/LP Less lamp
12-1/2(31.8)
5-3/4(14.6)
7-1/2(19.1)
Specifications
Length: 12-1/2 (31.8)
Depth: 7-1/2 (19.1)
Height: 5-3/4 (14.6)
Weight: 14.0 lbs (6.35 kg)
FEATURES & SPECIFICATIONSINTENDED USE — For building- and wall-mounted applications.
CONSTRUCTION — Rugged, die-cast, single-piece aluminum housing. Die-cast doorframe has a 1/8” thick tempered glass lens. Doorframe is fully gasketed with one-piece solid silicone.
Finish: Standard finish is textured dark bronze (DDBT) corrosion-resistant polyester powder finish, with other architectural colors available. Striping is also available.
OPTICS — Hydroformed reflector for superior uniformity and control. Medium throw (MD) full cutoff distribution only.
ELECTRICAL — Compact fluorescent utilizes an electronic, high frequency ballast. Compact fluorescent socket is four-pin positive latching thermoplastic. UL Listed. Quick-disconnect plug easily disconnects reflector from ballast and fixture from supply wires.
INSTALLATION — Easily installed using provided mounting strap. Mount to any non-combustible verti-cal surface over a 4” round or square recessed outlet box (by others). Back access through slotted gasket.
LISTINGS — Listed and labeled to UL standards. Listed and labeled to CSA standards (see Options). NOM Certified (see Options). IP65 rated. Wet location listed.
Note: Specifications subject to change without notice.
Decorative Wall-Mounted Lighting
WSTM COMPACT FLUORESCENT:
26DTT26-42TRT
Notes1 Multi-volt electronic ballast (compact fluorescent lamps) capable of
operating any line voltage between 120V and 277V.
2 May be ordered as an accessory with prefix “WS”. Must specify finish.
3 Must specify voltage. Not available with MVOLT.
4 Must be ordered with fixture; can not be field installed.
5 See www.lithonia.com/archcolors for additional color options.
6 Black finish only.
7 Must be specified (35K lamp with LPI).
WSTM-CF
OUTDOOR: One Lithonia Way Conyers, GA 30012 Phone: 770.922.9000 Fax: 770-918-1209 www.lithonia.com ©2006-2011 Acuity Brands Lighting, Inc. All rights reserved. Rev. 01/31/11
WSTM Compact Fluorescent Wall Mounted
DIS
TAN
CE
IN U
NIT
S O
F M
OU
NTI
NG
HEI
GH
T
ISOILLUMINANCE PLOT (Footcandle)
42W lamp, horizontal lamp orientation Footcandle values based on 12'mounting height, 3200 rated lumens.
-2
-1
0
1
2
3
4
50 1 2 3 4 5 6
2.51.510.5
0.25
TEST NO: LTL15247WSTM 42TRT MD
Luminaire Efficiency: 55.2%
OUTDOOR KAD-M-S
Catalog Number
Notes
Type
All dimensions are inches (centimeters) unless otherwise specified.*Weight as configured in example below.
KAD
Series Wattage Distribution Voltage Ballast Mounting12
KAD Metal halide70M1,2 250M5
100M1 320M4
150M 350M3,4
175M3 400M5,6
200M4
High pressure sodium1
70S100S150S250S400S
Ceramic metal halide70MHC1,2
100MHC1
150MHC
Standard reflectorsR2 IES type II
asymmetric7
R3 IES type III asymmetric7
R4 IES type IV forward throw7
R5S IES type V square
High performance reflectors8
SR2 IES type II asymmetric7
SR3 IES type III asymmetric7
SR4SC IES type IV forward throw
1202089
2409
2773474809
TB10
23050HZ11
(blank) Magnetic ballast
CWI Contant wattage isolated11
SCWA Super CWA pulse-start ballast
NOTE: For shipments to U.S. territories, SCWA must be specified to comply with EISA.
Ships in fixture cartonSPD__ Square poleRPD__ Round poleWBD__ Wall bracketWWD__ Wood or pole wallShips separately13,14
DAD12P Degree arm (pole)DAD12WB Degree arm (wall)WBA Decorative wall bracket15
KMA Mast arm external fitterKTMB Twin mounting bar
Arm length04 4" arm06 6" arm09 9" arm12 12" arm
ORDERING INFORMATION For shortest lead times, configure product using bolded options. Example: KAD 400M R3 TB SCWA SPD04 LPI
Options Finish20 Lamp21
Shipped installed in fixtureSF Single fuse (120, 277, 347V)16
DF Double fuse (208, 240, 480V)16
PD Power tray17
PER NEMA twist-lock receptacle only (no photocontrol)
QRS Quartz restrike system18
QRSTD QRS time delay18
WTB Terminal wiring block17
CSA CSA CertifiedINTL Available MH for probe start
shipping outside the U.S.REGC1 California Title 20, effective
1/1/2010Shipped separately13
HS House side shieldPE1 NEMA twist-lock PE (120,
208, 240V)
PE3 NEMA twist-lock PE (347V)PE4 NEMA twist-lock PE (480V)PE7 NEMA twist-lock PE (277V)SC Shorting cap for PER
optionVG Vandal guard19
WG Wire guard19
(blank) Dark bronzeDWH WhiteDBL BlackDMB Medium bronzeDNA Natural aluminumSuper Durable FinishesDDBXD Dark bronzeDBLXD Black
DNAXD Natural aluminumDWHXD WhiteDDBTXD Textured dark bronzeDBLBXD Textured blackDNATXD Textured natural
aluminumDWHGXD Textured white
LPI Lamp included
L/LP Less lamp
Soft Square Lighting
KAD METAL HALIDE: 70-400W HIGH PRESSURE SODIUM: 70-400W
20’ TO 35’ MOUNTING
Specifications
EPA: 1.2 ft.2
*Weight: 35.9 lbs (16.28 kg)
Length: 17-1/2 (44.5)
Width: 17-1/2” (44.5)
Depth: 7-1/8 (18.1)
FEATURES & SPECIFICATIONSINTENDED USE – Ideal for parking areas, street lighting, walkways and car lots.CONSTRUCTION – Rugged, die-cast, soft corner aluminum housing with 0.12” nominal wall thickness. Die-cast door frame has impact-resistant,tempered, glass lens that is fully gasketed with one-piece tubular silicone.Finish: Standard finish is dark bronze (DDB) polyester powder finish, with other architectural colors available.OPTICS – Anodized, aluminum reflectors: IES full cutoff distributions R2 (asymmetric), R3 (asymmetric), R4 (forward throw) and R5S (square) are interchangeable. High-performance anodized, segmented aluminum reflectors IES full cutoff distributions SR2 (asymmetric), SR3 (asymmetric) and SR4SC (forward throw, sharp cutoff). High-performance reflectors attach with tool-less fasteners and are rotatable and interchangeable.ELECTRICAL – Ballast: High pressure sodium: 70-150W is high reactance, high power factor. Constant wattage autotransformer for 200-400W. Metal halide: 70-150W is high reactance, high power factor and is standard with pulse-start ignitor technology. “SCWA” not required. Constant wattage autotransformer for 175-400W. Super CWA (pulse start ballast), 88% efficient and EISA legislation compliant, is required for metal halide 151-400W (SCWA option) for US shipments only. CSA, NOM or INTL required for probe start shipments outside of the US. Pulse-start ballast (SCWA) required for 200W, 320W, or 350W. Ballast is 100% factory-tested.Socket: Porcelain, horizontally oriented medium base socket for 70-150M. Mogul base socket for 175M and above, and 70-400S, with copper alloy, nickel-plated screw shell and center contact. UL listed 1500W, 600V.LISTINGS – UL Listed (standard). CSA Certified (see Options). UL listed for 25°C ambient and wet locations. IP65 rated in accordance with standard IEC 529.WARRANTY — 1-year limited warranty. Complete warranty terms located atwww.acuitybrands.com/CustomerResources/Terms_and_conditions.aspxNote: Specifications subject to change without notice.
Notes1 Not available with SCWA.2 Not available with 480V.3 These wattages do not comply with
California Title 20 regulations.4 Must be ordered with SCWA.5 These wattages require the REGC1
option to be chosen for shipments into California for Title 20 compliance. 250M REGC1 in not available in 347 or 480V.
6 Reduced jacket ED28 required for SR2, SR3 and SR4SC optics.
7 House-side shield available.
8 High performance reflectors not avail-able with QRSTD.
9 Must specify CWI for use in Canada.10 Optional multi-tap ballast (120, 208,
240, 277V; in Canada: 120, 277, 347V).11 Consult factory for available wattages.12 9" arm is required when two or more
luminaires are oriented on a 90° drilling pattern.
13 May be ordered as an accessory. 14 Must specify finish when ordered as an
accessory.
7-1/8(18.1)
4(10.2)
17-1/2(44.5)
®
Accessories: Tenon Mounting Slipfitter (RPxx required.)Order as seperate catalog number. Must be used with pole mounting.
Number of fixturesTenon O.D. One Two@180° Two@90° Three@120° Three@90° Four@90°
2-3/8" T20-190 T20-280 T20-29022 T20-32022 T20-39022 T20-49022
2-7/8" T25-190 T25-280 T25-29022 T25-320 T25-39022 T25-49022
4 T35-190 T35-280 T35-29022 T35-320 T35-39022 T35-49022
15 Available with SPD04 and SPD09.16 Must specicy voltage. N/A with TB.17 Only available with SR2, SR3 and
SR4SC optics.18 Max allowable wattage lamp included. 19 Prefix with KAD when ordered as an
accessory.20 See www.lithonia.com/archcolors for
additional color options.21 Must be specified. L/LP not available
with MHC. 22 Must use RPD09.
KAD-M-S
OUTDOOR: One Lithonia Way Conyers, GA 30012 Phone: 770.922.9000 Fax: 770-918-1209 www.lithonia.com ©2007-2012 Acuity Brands Lighting, Inc. All rights reserved. Rev.12/04/12
KAD Metal Halide, Arm-mounted Soft Square Cutoff
Mounting Height Correction Factor(Multiply the fc level by the correction factor)25 ft. = 0.64 35 ft. = 0.32 40 ft. = 0.25
Coefficient of UtilizationInitial Footcandles
Notes
1 Photometric data for other distributions can be accessed at www.lithonia.com.
2 Tested to current IES and NEMA standards under stabilized laboratory conditions. Various operating factors can cause differences between laboratory data and actual field measurements. Dimensions and specifications on this sheet are based on the most current available data and are subject to change without notice.
3 For electrical characteristics, consult outdoor technical data specification sheets on www.lithonia.com.
Existing Mounting Height New Mounting Height
2
= Correction Factor
KAD 400M R2 Test no. 1193083101P KAD 400M R3 Test no. 1192040902P
KAD 400M R4HS Test no. 1192061101P KAD 400M R4 Test no. 1191110101P
DIS
TAN
CE
IN U
NIT
S O
F M
OU
NTI
NG
HE
IGH
T
ISOILLUMINANCE PLOT (Footcandle)
400W pulse start metal halide lamp, rated 38000 lumens. Footcandle values based on 20'mounting height.Classification: Type II, Short, Full Cutoff
-3
-2
-1
0
1
2
3
40 1 2 3 4 5 6
52.51.510.5
0.25
DIS
TAN
CE
IN U
NIT
S O
F M
OU
NTI
NG
HE
IGH
T
ISOILLUMINANCE PLOT (Footcandle)
400W pulse start metal halide lamp, rated 38,000 lumens. Footcandle values based on 20'mounting height.Classification: Type II, Short, Full Cutoff
-3
-2
-1
0
1
2
3
40 1 2 3 4 5 6
52.51.5
10.5
0.25
DIS
TAN
CE
IN U
NIT
S O
F M
OU
NTI
NG
HE
IGH
T
ISOILLUMINANCE PLOT (Footcandle)
400W pulse start metal halide lamp, rated 38,000 lumens. Footcandle values based on 20'mounting height.Classification: Unclassified (Type III, Very Short), Full Cutoff
-3
-2
-1
0
1
2
3
40 1 2 3 4 5 6
52.51.510.5
0.25
DIS
TAN
CE
IN U
NIT
S O
F M
OU
NTI
NG
HE
IGH
T
ISOILLUMINANCE PLOT (Footcandle)
400W pulse start metal halide lamp, rated 38,000 lumens. Footcandle values based on 20'mounting height.Classification: Unclassified (Type III, Very Short), Full Cutoff
-3
-2
-1
0
1
2
3
40 1 2 3 4 5 6
52.51.510.5
0.25
KAD 400M R5S Test no. 1194040801P
DIS
TAN
CE
IN U
NIT
S O
F M
OU
NTI
NG
HE
IGH
T
ISOILLUMINANCE PLOT (Footcandle)
400W pulse start metal halide lamp, rated 38000 lumens. Footcandle values based on 20'mounting height.Classification: Unclassified (Type NC, Very Short), Full Cutoff
-3
-2
-1
0
1
2
3
40 1 2 3 4 5 6
52.51.510.5
0.25
Catalog Number
Notes Type
FEATURES & SPECIFICATIONSINTENDED USEIdeal for a wide variety of low- to medium-height ceiling applications including commercial, retail and hospitality spaces where an open or damp location lensed fixture is required.CONSTRUCTIONHeavy gauge die formed galvanized steel mounting frame. Attached to frame are vertically adjustable mounting brackets for use with C channels, ½” steel conduit or 16 gauge flat bar hangers included, standard. Frames equipped with galvanized junction box UL Listed for through wire applications. Junction boxes equipped with (2) ¾” and (4) ½” conduit knockouts with pryout slots and removable access doors.Maximum 1-1/2” ceiling thickness.OPTICSAluminum full reflectors are optically designed to maximize lumen output and to provide superior glare control. Anodized finishes for open reflectors are semi-specular or diffuse in a variety of colors. Polyester powder coat finishes also are available in white.Lenses are available in clear flat glass, tempered prismatic glass or polycarbonate to provide optimal visual comfort and improved aesthetics. Lens is recessed 1-1/2 (3.8) from flange.ELECTRICAL Electronic ballast with end of lamp life protection standard. Class P thermally protected ballast protects against improper contact with insulation. Minimum starting temperature is 0°F/-18°C.Rated for #12 AWG conductor thru-branch wiring. Minimum 90° supply wire. Ground wire provided.Lamp Socket Base:DTT 4-pin lamps – 18W (G24Q-2); 26W (G24Q-3)TRT 4-pin lamps – 18W (GX24Q-2); 26W (GX24Q-3); 32W (GX24Q-3); 42W (GX24Q-4)LISTINGFixtures are UL Listed for thru-branch wiring, Non-IC recessed mounting, damp location, and to U.S. and Canadian Safety Standards.
Compact Fluorescent Downlighting
6” LF6NOPEN REFLECTOR
Horizontal 1-Lamp, Triple Tube (TRT)
All dimensions are inches (centimeters).
SpecificationsMax. height: 6-3/8 (16.2)Ceiling opening: 7 (17.8)Overlap trim: 7-1/2 (19.1)Length: 13 (33.0)Width: 11 (27.9)
Series
LF6N
LF6N
Wattage/lamp
1/18DTT1/26DTT1/18TRT
1/26-42TRT1
1/26TRT1/32TRT1/42TRT
Voltage
MVOLT2
1202773473
Options7
ADEZ Advance Mark 10™ electronic dimming ballast, 120V or 277V. Must be voltage specific. Mini-mum dimming level 5%
ECOS Lutron EcoSystem electronic dimming ballast, 120V - 277V. Must be wattage specific. Mini-mum dimming level 5%
EL Emergency PSDL3 DL battery pack with integral test switch. Lens removal re-quired before EL testing4
ELR Emergency PSDL3 DL battery pack with remote test switch4
ELHL Iota I-420-R High lumen output emergency battery pack. Internal test switch provided. Maximum average lumen output is 1300 (42W)5
ELRHL Iota I-420-EM-B High lumen output emergency battery pack. Remote test switch provided. Maximum average lumen output is 1300 (42W)5
GMF Single slow-blow fuse, must specify voltage BDP Ballast disconnect plug (meets codes that
require in-fixture disconnect)3
RIF1 Radio interference filter LBH Less barhangers WLP 35K lamp (shipped separately) NSD Sensor Switch nLight™ dimming relay6
TRW White flange
NOTES:1 Not available with ECOS or WLP.2 Electronic multi-volt ballast capable of operating any
line voltage from 120-277V, 50 or 60Hz.3 Not available with EL or ELR.4 Add 3” (7.6) to width and 4-1/2” (11.4) to length.5 Not recommended for field installation.6 One 5A relay with one 0-10 VDC dimming output,
shipped installed. Requires additional nLight bus power supply.
7 For additional options see lithonia.com.
Reflector/color
F6O1 White open F6O1A Clear diffuse
open F6O1AZ Clear semi-
specular open F6O1G Gold diffuse
open F6O1GZ Gold semi-spec-
ular open F6O1PR Pewter diffuse
open F6O1WTZ Wheat semi-
specular open
Downlighting and Track
Lens type
(blank) No lens CGL Clear glass lens T73 Tempered glass
prismatic lens PCL Clear polycar-
bonate lens
Sheet #: LF6N-OPEN-1-TRT
For shortest lead times, configure product using standard options (shown in bold).Example: LF6N 1/26-42TRT F6O1AZ MVOLT
ORDERING INFORMATION
AccessoriesOrder as separate catalog number
SCA6 Sloped ceiling adaptor. Degree of slope must be specified (10D, 15D, 20D, 25D, 30D) Ex: SCA6 10D.
CTE6 Ceiling thickness extender is used when ceiling thickness is greater than 1-1/2 (3.8). Maximum thickness 2 (5.1).
6-3/8(16.2)
6-1/4(15.9)7-1/2(19.1)
6-3/8(16.2)
7-1/2(19.1)
11(27.9)
13(33.0)
Lithonia LightingRecessed Downlighting and TrackOne Lithonia Way, Conyers, GA 30012Phone: 800-315-4935 Fax: 770-918-1209www.lithonia.com
Distribution Curve Distribution Data Output Data Coefficient of Utilization Illuminance Data at 30” Above Floor for a Single Luminaire
6” LF6N Horizontal 1-Lamp, Triple Tube (TRT), Open
© 2009-2011 Acuity Brands Lighting, Inc. All rights reserved. Rev. 3/7/11Sheet #: LF6N-OPEN-1-TRT
10˚ 30˚
50˚
70˚
90˚
100
200
300
400
500
pf 20%pc 80% 70% 50%pw 50% 30% 50% 30% 50% 30%
5651464137343128262422
5649433834302725222019
5450454137333028262422
5448433834302724222019
5248433936333027252321
5247423733302724222018
0123456789
10
Zone Lumens % Lamp0˚ - 30˚0˚ - 40˚0˚ - 60˚0˚ - 90˚90˚ - 180˚0˚ - 180˚
42768211061119
01119
17.828.446.146.60.046.6
Efficiency: 46.6%
0˚0˚5˚15˚25˚35˚45˚55˚65˚75˚85˚90˚
55153251341036533418910310
Task Height: 2.5ft.50% beam -
59.8˚10% beam- 104.6˚
MtgHt
Inital fcCenterBeam Diameter fc Diameterfc
810121416
18.29.86.14.23.0
69111316
95322
1419253035
21100
LF6N 1/32TRT F6O1AZ T73 MVOLT, (1) 32W TRT Lamp, 2400 rated lumens per lamp, 1.2 s/mh, Test No. LTL15103
LF6N 1/32TRT F6O1AZ CGL MVOLT, (1) 32W TRT Lamp, 2400 rated lumens per lamp, 1.1 s/mh, Test No. LTL15102
10˚ 30˚
50˚
70˚
90˚
100
200
300
400
500
pf 20%pc 80% 70% 50%pw 50% 30% 50% 30% 50% 30%
5045413733302826242220
5044383430272522211917
4944403633302825232220
4943383430272422201917
4743393532292725232120
4742373329272422201917
0123456789
10
Zone Lumens % Lamp0˚ - 30˚0˚ - 40˚0˚ - 60˚0˚ - 90˚90˚ - 180˚0˚ - 180˚
4366749261007
01007
18.128.138.641.90.041.9
Efficiency: 41.9%
0˚0˚5˚15˚25˚35˚45˚55˚65˚75˚85˚90˚
585570519460372204107573210
Task Height: 2.5ft.50% beam -
61.3˚10% beam
- 93.3˚
MtgHt
Inital fcCenterBeam Diameter fc Diameterfc
810121416
19.310.46.54.43.2
79111416
105322
1216202429
21100
NOTE: Energy (Calculated in accordance with NEMA Standard LE-5.)
LF6N 1/32TRT F6O1AZ MVOLT, (1) Philips PL-C 32W/27SH lamp, 1.2 s/mh, 2400 rated lumens, Test no. LTL12515
Zone Lumens % Lamp
0˚ - 30˚0˚ - 40˚0˚ - 60˚0˚ - 90˚
90˚ - 180˚0˚ - 180˚
483.7780.11245.01261.5
0.01261.5
20.232.551.952.60.0
*52.6*Total Eff iciency
10˚ 30˚
50˚
70˚
90˚
100
200
300
400
500
600
pf 20%pc 80% 70% 50%pw 50% 30% 50% 30% 50% 30%012345678910
6357524742383532292725
6355494338343128252321
6156514642383432292725
6154484338343128252321
5854494440373431282624
5853474237333027252321
Task Height: 2.5ft.50% beam - 62.9˚ 10% beam -
104.1˚
MountingHeight
Inital FCCenterBeam Diameter FC Diameter FC
8.010.012.014.016.0
19.810.66.64.53.3
6.79.2
11.614.116.5
9.95.33.32.31.6
14.119.224.329.534.6
2.01.10.70.50.3
cp Lumens
05152535455565758590
59861263953347144413711310
591782472963301351231