By Michael A. Jensen

Sabroe Factory NetTraining COMP1 and sales tools

SABROE FACTORY

Johnson Controls PowerPoint Guidelines | February 8, 2008 2

Sabroe Factory NetTraining

COMP1 Select and templates

COMP1 & Sales tools Nettraining, MAJ/BBP | 3 September 2013 3

COMP1 - basics

Introduction to COMP1 Select and templates

How to use it

(recip and ChillPAC used for presentation)

Computation example

(COMP1 computation)

COMP1 & Sales tools Nettraining, MAJ/BBP | 3 September 2013 4 4

Introduction

COMP1 is a technical computation program for Sabroe refrigeration equipment that enables the user to

make thermal and mechanical sizing of Sabroe compressors, chillers, CAFPs, heat exchangers etc.

combine compressors with heat exchangers

make part load evaluations for compressors and heat exchangers

price Sabroe compressors and chillers.

COMP1 & Sales tools Nettraining, MAJ/BBP | 3 September 2013 5 5

COMP1 Layout

Data in (Input view)

Data out (Output view)

COMP1 & Sales tools Nettraining, MAJ/BBP | 3 September 2013 6

COMP1 Select

The ‘Select‘ function is a means to get an overview of available products that meet the cooling demand for your project.

COMP1 & Sales tools Nettraining, MAJ/BBP | 3 September 2013 7 7

COMP1 Compressor selection

Data in (Input view)

Compressor Select is an easy and simple way to find a compressor that matches your demand. Step 1: Go to COMP1 front page. Step 2: Press the ’Compr. Select’ button.

COMP1 & Sales tools Nettraining, MAJ/BBP | 3 September 2013 8 8

COMP1 Compressor selection

Step 3: Select refrigerant. Step 4: Mark the compressor types that you want to choose from. Step 5: Decide if the capacity is to be shown for mass flow or cooling capacity. Step 6: Select grid frequency. Step 7: Select drive type (belt is for recips only). Step 8: Select high or low-stage compressor operation. Step 9: Select oil cooling for screw compressor, if screw compressor box is ticked off. Step 10: Specify operating Conditions. Step 11: Press ’Select’.

COMP1 & Sales tools Nettraining, MAJ/BBP | 3 September 2013 9 9

COMP1 Compressor selection

Finally import the project selection to COMP1 calculation. Step 12: Highlight the preferred selection. Step 13: Press the ’COMP1’ button.

COMP1 & Sales tools Nettraining, MAJ/BBP | 3 September 2013 10 10

COMP1 Chiller selection

Data in (Input view)

Chiller Select is an easy and simple way to find a chiller that matches the demand. Step 1: Go to COMP1 front page. Step 2: Press the ’Chiller Select’ button.

COMP1 & Sales tools Nettraining, MAJ/BBP | 3 September 2013 11 11

COMP1 Chiller selection

Step 3: Select refrigerant. Step 4: Mark the chiller types and numbers that you want to choose from. Step 5: Specify grid frequency. Step 6: Specify evaporator conditions. Step 7: Specify condenser conditions. Step 8: Press ’Select’.

COMP1 & Sales tools Nettraining, MAJ/BBP | 3 September 2013 12 12

COMP1 Chiller selection

Finally import the project selection to COMP1 calculation. Step 9: Highlight the preferred selection. Step 10: Press the ’COMP1’ button.

COMP1 & Sales tools Nettraining, MAJ/BBP | 3 September 2013 13

COMP1 - Template

The ‘Template‘ function is a means to optimise computations when you already know which product you want to use for your project.

COMP1 & Sales tools Nettraining, MAJ/BBP | 3 September 2013 14 14

COMP1 Template-based computation

Template-based computation is an easy and quick way to start computations to review different operating conditions and find the best compressor match. Step 1: Open COMP1 front page. Step 2: Press the ’Template’ button – and the ’Input template’ window will open. Step 3: Highlight the type of packaged unit and the type of compressor to review. In this case we look at a reciprocating compressor unit.

COMP1 & Sales tools Nettraining, MAJ/BBP | 3 September 2013 15 15

COMP1 Print settings

Printer settings can be user- customised. Step 1: Open COMP1 front page. Step 2: Open ’Configure’ in the menu. Step 3: Open ’Print Options’ in the COMP1 configuration window. Step 4: Select your print options. Step 5: Press the ’Save’ button. Step 6: Press the ’Save’ button.

COMP1 & Sales tools Nettraining, MAJ/BBP | 3 September 2013 16 16

COMP1 End of presentation

... and we will now go to COMP1 computations.