Post on 25-Dec-2015
RFI Mitigation Techniques for RadioAstronomy
Michael Kesteven
Australia Telescope National Facility
Groningen, 28 March 2010
RFI mitigation. Groningen, 2010
• Introduction• The issues• RFI-free environments• Blanking• RFI cancellation• The low RFI levels problem• The large dataset problem• Prospects
RFI mitigation. Groningen, 2010
Introduction
In the past decade a number of RFI mitigation techniques have been trialled and shown to work.
Yet few observatories have on-line RFI mitigation installed.
Has its time now arrived, perhaps?
RFI mitigation. Groningen, 2010
There is no universal solution
• Different sources of RFI• TV/Communications
• Satellites
• Observatory-based
• Different types of Telescopes• Single dish
• arrays
• Different observing regimes• Low frequency; high frequency
• VLBI
• Pulsars
• Spectral line
• Continuum
RFI mitigation. Groningen, 2010
The ITU RA-769 argument
A.R.Thompson provided a useful framework to describe the impact of RFI. Of interest here is the link between the observation mode and the RFI levels.
Recognise that RFI entering the main beam of a telescope (LOFAR apart) is generally a lost cause. Pitch the debate at RFI in the far sidelobes - at the level corresponding to a 0 dBi gain.
RFI mitigation. Groningen, 2010
Single Dish Operation
Natural defences are few
antenna sidelobes (0 dBi gain)
Mitigation techniques work well
adaptive filters
blanking
Datasets are modest (relatively speaking)
detailed probes over the entire dataset are realistic
Vulnerable to low level interference
RFI mitigation. Groningen, 2010
Arrays
Natural defences are better:
antenna sidelobes
phase tracking decorrelation
delay decorrelation (continuum observations)
spatial resolution
Mitigation techniques less well developed
Datasets could become huge
Some advanced techniques may not be realistic in the near term
RFI mitigation. Groningen, 2010
Current response to RFI
- Flag/blank post-detection data.
- Retune the receiver to an adjacent frequency
- Tolerate it
- Reschedule the observations
RFI mitigation. Groningen, 2010
The Challenge
We need machinery to reduce the impact of RFI which is damaging the astronomer’s data.
- It should be automatic, reliable and robust.
- It should not introduce artefacts which mimic real results.
- The cost of applying the machinery should be predictable.
- The cost should be less than the cost of doing nothing.
(cost : $, science, time)
RFI mitigation. Groningen, 2010
Mitigation Options
Pro-active mitigation : AvoidanceRemove the RFI at source.
Re-active mitigation : Remove the RFI from the dataBlank those parts of the astronomical data space which
contain RFI ---- excision.
Identify and remove the RFI while leaving the astronomy untouched --- cancellation.
RFI mitigation. Groningen, 2010
Avoidance no RFI to mitigate
- Remote Locations
- Regulation- Spectrum Management
- Radio quiet zones
- Good observatory practice- Discipline
- Good design
- Maintenance
- Constant monitoring
RFI mitigation. Groningen, 2010
RFI mitigation. Groningen, 2010
Blanking, Flagging
This is the current mitigation strategy of choice.
It is attractive to observers because it is simple and its consequences are predictable:
• The loss in sensitivity is related to the amount of data discarded.
• The effect on the image quality can be estimated.
• It is straightforward in its implementation, and can easily be automated.
RFI mitigation. Groningen, 2010
Excision
Radiometer integration period (~msec)Time
Pulsed interferer (~sec)
Requirements:
- The RFI events occupy a small fraction of the data space.- Each RFI event has to be detectable – needs INR > 1 in small number of samples.
RFI mitigation. Groningen, 2010
Excision – Real Time blanking
- Given the mean and rms of good data, define RFI to be those samples above a threshold (= *rms)
- Need to buffer some small number of data samples in order to be able to distinguish good from bad.
- The buffer allows you to apply some intelligence: determine the local mean and rms in order to identify the outliers.
- The buffer allows further options – one could blank a known pulse shape, for example.
RFI mitigation. Groningen, 2010
Implementations
A number of observatories have built hardware, on-line blanking devices.
- Arecibo, for example, addresses the serious RFI from neighbouring radar. The known timing details of the pulsing assists the blanking trigger.
- WSRT have demonstrated an impressive unit built around digital processing boards which, amongst in many capabilities, can provide on-line blanking.
RFI mitigation. Groningen, 2010
Excision Post-correlation Blanking.
Flag the data – instruct the downstream imaging/processing machinery to ignore the corrupt samples.
This is the RFI-mitigation strategy of last resort.
Tedious when done manually; automated scripts now available.
When this is applied to the correlator output data, the minimum quantum of rejected data is the size of the correlator dump cycle.
RFI mitigation. Groningen, 2010
ATCA – Middleberg Automated flagging
RFI mitigation. Groningen, 2010
Frequency Blanking
Discarding data in frequency space is a variant of this approach: modern high speed processing allows fine on-line spectral analysis, so that corrupted channels can be identified and excised.
This is an option if the discarded fraction of frequency space is modest compared to the overall bandwidth.
LOFAR includes this in its armoury.
RFI mitigation. Groningen, 2010
Excision Issues
The technique relies on the ability to detect RFI from a small number of samples (or from a priori information). It generally requires good INR. Long integrations with low INR will be compromised
INR > 10 is a rough guide. There may be little to be gained by integration if the RFI is pulsed, as the INR is essentially based on a relatively small number of samples. (Periodic RFI is a separate case).
Downstream processing should not be compromised. Care needed in defining the replacement sample.
Discarding data in synthesis arrays will affect the (u,v) plane population and may therefore compromise the imaging quality.
RFI mitigation. Groningen, 2010
Excision – Bottom line
It can be a viable technique if the cost to science is modest.
It depends on some prior definition of “badness”, and it depends on a low duty cycle.
RFI mitigation. Groningen, 2010
Cancellation
This is the more ambitious approach – identify and characterise the RFI; then remove just the RFI.
This is a two-step process:
1. Characterise the RFI.
2. Subtract the RFI from the data – to give the astronomer an RFI-free dataset.
RFI mitigation. Groningen, 2010
Cancellation -- How is the RFI identified?
- Extract the RFI details from the data itself.
- Point a reference antenna towards the RFI -- use adaptive filter.
- Predict the RFI from published data (eg, GLONASS) – use software adaptive filter.
RFI mitigation. Groningen, 2010
Questions:
Mitigate on the data on-the-fly ? (each correlator dump)
Or
Mitigate on the entire observation.
SNR is the issue with the first; Data volume the problem with the second.
RFI mitigation. Groningen, 2010
Filter Variants
• Image plane filtering
• Spatial filtering
• Null Steering
• Cyclo-stationary filters
• Adaptive filters
RFI mitigation. Groningen, 2010
Clean/self-calibration filter (Cornwell-NRAO)
Identify the RFI in the imaging stage. Apply self-calibration to the RFI. Remove the RFI.
Stationary RFI will map to the pole.
The self-calibration operates simultaneously in two areas :
- The astronomical target;
- The RFI which is stationary with respect to the observatory. The self-calibration accounts for the phasing and amplitude variations.
It requires the data to be sampled much faster than the astronomical target would require.
RFI mitigation. Groningen, 2010
Cornwell – 327 MHz.
No Filtering Filter active
RFI mitigation. Groningen, 2010
Spatial Filtering
• Each object within the field of view of the array will add a specific signature to the full set of correlation products between the antennas.
• An eigenvalue decomposition of the product matrix will isolate the strongest sources.
• A projection operation can then remove the RFI sources.
• This scheme has long history, most recently successfully demonstrated in the LOFAR trials.
RFI mitigation. Groningen, 2010
The LOFAR snapshot variant
1. Within each widefield (whole sky) snapshot identify and remove the RFI point sources (as found by spatial filtering).
This cleans the snapshot down to sky noise.
2. Stacking the sky-aligned snapshots builds the SNR on the astronomical objects while dissolving the remaining RFI.
RFI mitigation. Groningen, 2010
This scheme is best suited to low frequency arrays (LOFAR)
There are problems at higher frequencies, where very short correlator cycle times are required.
The computing load for a detailed spatial filtering operation may be a limiting factor.
RFI mitigation. Groningen, 2010
Cyclostationary Filters
• The concept here is to identify the RFI by its temporal signature, cyclostationarity. This attribute is specific to RFI.
• The classical spatial filtering matrix is replaced by a variant which is matched to a cyclic frequency.
• The projection operation then proceeds as before, to remove the RFI.
• This scheme has had some initial (promising) trials on LOFAR.
RFI mitigation. Groningen, 2010
Null Steering
The ATA is an array of 42 antennas that includes a beamformer mode of operation, each beam directed to a potential target. This opens the possibility of adjusting the beamformer weights to position nulls in the direction of known RFI sources – fixed or mobile.
Wide-band nulls may be required (and have been demonstrated).
The process works well, but has serious implications for the bandwidth of the phase tracking machinery.
RFI mitigation. Groningen, 2010
Adaptive Filters
These have been applied to :
• Single Dish• Arrays
The starting point is to obtain a copy of the RFI.
We manipulate this copy to match the RFI in the data – the function of the adaptive filter.
We then subtract the modified copy from the data.
RFI mitigation. Groningen, 2010
Cancellation Real-time adaptive filter
RFI mitigation. Groningen, 2010
Cancellation. Issues with the real-time filter
It requires modest INR. Averaging at the correlation step helps.
It can cope with multi-pathing, but not with multiple transmitters on the same frequency channel.
With no RFI there is no added noise. Gain drops to zero.
It adapts automatically to changes in the relative transmission path details.
RFI mitigation. Groningen, 2010
Filter OFF Filter ON
RFI mitigation. Groningen, 2010
Real-time adaptive filter
Best suited to continuum single dish observations.
Works well for pulsar and VLBI observations.
It may not be suitable for spectral line observations, as the cancellation is not complete, and the residuals will mimic the original RFI spectrum.
It could be difficult to implement in an array.
RFI mitigation. Groningen, 2010
Post-Correlation adaptive filter
• We combine three cross-products to get a good estimate of the interference in the astronomical channel.
• No total power products in the cross-products, thus no bias.
• Noise*RFI products are also removed.
• The signal/noise is set by the ratio of Correlated RFI to noise products -
cBINR~ SNR
RFI mitigation. Groningen, 2010
Reference antenna
Parkes 64m
Single Dish – post-correlation
RFI mitigation. Groningen, 2010
Adaptive filters
• Both real-time and post-correlation filters use the INR as a control factor – the filter switches off when INR <~ 1
This makes the filter robust.
• Both filters subtract the correction term from the raw astronomy signal – they do not modify the astronomy.
• The real-time filter provides attenuation, leaving some residual RFI power;
• The post-correlation provides cancellation, with some added
residual zero-mean noise.
RFI mitigation. Groningen, 2010
Postcorrelation filter applied to an array
• The Post-correlation adaptive filter has been successfully applied to an array.
• A reference antenna provided the RFI copy.
• This copy followed the same conversion chain and correlation path as all the antennas of the array.
• Each baseline was corrected for RFI after computing a baseline-specific correction term.
RFI mitigation. Groningen, 2010
Synthesis Array Filtering(ATCA, 1503 MHZ, 4 MHZ BW)
RFI mitigation. Groningen, 2010
Before and after images
RFI mitigation. Groningen, 2010
Post-correlation Adaptive filter - Issues
- Still effective with low INR (to ~ 0.1)
- Will require additional correlator capacity
- Works well with single dish.
- Works well with an array, but may require short correlator dump times
RFI mitigation. Groningen, 2010
The Low INR problem
The mitigation schemes generally work on short sections of data,
but the astronomer works with the entire dataset.
Low level RFI which may only show up in the final product is of concern.
Future arrays may have too much data to allow RFI mitigation predicated on the entire dataset. The ASKAP, for example, needs to complete the processing on-the-fly, when in high-resolution spectral mode.
RFI mitigation. Groningen, 2010
Conclusions
The prospects look good at the low-frequency (LOFAR) end of the spectrum.
The issue is less clear at SKA frequencies and above.
A number of niche areas, such as VLBI and pulsars, look tractable.
Contact UsPhone: 1300 363 400 or +61 3 9545 2176
Email: enquiries@csiro.au Web: www.csiro.au
Thank you
Australia Telescope National FacilityMichael Kesteven
Phone: 61 2 9372 4544Email: michael.kesteven@csiro.auWeb: www.csiro.au/group
RFI mitigation. Groningen, 2010
Array Adaptive Filter
termcorrection the- - - R2R1
R2BR1A
RFI astronomy the--- BA
We introduce two additional “antennas” into the correlator system, R1 and R2, from the reference antenna.
RFI mitigation. Groningen, 2010
Real-time & Post-Correlation Filters
(f)C - (f)C (f)C :filter n correlatio-Post
(t)V - (t)V (t)V :filter adaptive time-Real
corrinout
corrinout
RFI mitigation. Groningen, 2010
Preliminaries types of RFI
- Continuous (TV)
likely to be an issue for long integrations, single dish.
handled well by adaptive filters.
- Impulsive (radar)
amenable to blanking if strong.
diluted and not important if low level
(minor increase in Tsys)
- Short term, strong (satellites)
predictable, so precautionary measures possible.
RFI mitigation. Groningen, 2010
Adaptive Filter Performance (1)
Adopting the RA-769 criteria we can estimate the limitations of the adaptive filter.
1. The ratio of the RFI powers in the main and reference antennas is :
r = (Area of 0 dBi antenna) / (Area of the reference antenna)
r = (R)2 [= 0.0016 at 600 MHz, 4m ref antenna]
2. The residual power (due to the RFI) in the filtered output :
resid = r * Tsys * INR / (1 + INR)
RFI mitigation. Groningen, 2010
3. resid tends to r*Tsys for large INR.
4. The filter starts to fade out at INR ~ 1, with resid ~ r*Tsys/2
5. Thereafter resid falls gracefully to 0 as the INR decreases.
RFI mitigation. Groningen, 2010
General Issues
What does the RFI look like in the final data product?
- RA769 assumed white noise (Tsys argument)
- But fringe decorrelation has poor cancellation on small baselines, and for v=0 baselines. Leads to (1/f) –type rubbish.
RFI mitigation. Groningen, 2010
General issues
When does the RFI mitigation machinery detect the RFI ?
- On a sample-by-sample basis?- In modest sample packets?- In the entire dataset?
Dilemma: low INR RFI may only be visible after a long integration.
- Need to boost the INR in the short sample mitigation strategy.
antenna with gain >
RFI mitigation. Groningen, 2010
Post-Correlation adaptive Filter in an ARRAY
RFI mitigation. Groningen, 2010
ATCA - 1503 MHz; 4 MHz BW
Mean amp
filter OFF filter ON
Mean phase
freqfreq
RFI mitigation. Groningen, 2010
MRO Protection
• Observatory grounds (120 km2)• Full/self-control
• Boolardy Pastoral Station (3467 km2/856,835 acres)• CSIRO held and operated
• Mineral Management Area (80 km radius) - State• Controls for non-licensed radiators
• Section 19 - State• Embargo on new mines in the region
• ACMA RALI September 2007 - Commonwealth• (Aus Communication & Media Authority Radiocommunications
Assignment and Licensing Instruction)
• “FCC RQZ” protection (various radii)
• Additional State/Commonwealth Legislation being pursued
RFI mitigation. Groningen, 2010
MRO Protection
RFI mitigation. Groningen, 2010
Excision – The COST
Data is lost.
samplesofNumberSNR __
In time-frequency blanking, some frequency channels may be abandoned.
RFI mitigation. Groningen, 2010
Boolardy, 2008 median
RFI mitigation. Groningen, 2010
Scaling the RFI copy – adaptive filter
• Use an adaptive filter (real-time, or post-correlation).
- Note the importance of the ref antenna receiver noise – ensures the distinction between zero correlation (= filter optimally adjusted) and zero correlation (no RFI).
- Optimally adjusted filter -> the (reference antenna – main antenna pair) now has a null positioned on the RFI.
RFI mitigation. Groningen, 2010
MRO Protection
• Observatory grounds (120 km2)• Full/self-control
• EMC control region (30 km radius)• No inhabitants
• Control, but negotiation with pastoral activities
• Mineral Management Area (80 km)• Controls for non-licensed radiators
• Section 19• Large region limiting mining activity (no new mines in the region)
within blue
RFI mitigation. Groningen, 2010
RALI
RFI mitigation. Groningen, 2010
MRO RQZ Protection
Frequency Range
(MHz)
Restricted Zone Radius (km)
Coordination Zone Radius (km)
Threshold (dBm/Hz)
100-230 150 260 -214
230-400 100 180 -222
400-520 100 165 -224
520-820 100 190 -224
820-1000 100 145 -228
1000-2300 100 140 -230
2300-6000 100 120 -232
6000-10000 100 - -232
10000-25250 100 - -236
RFI mitigation. Groningen, 2010
Cancelation
We have attenuation of the RFI:-2)1(
1
INRatt
We have additional receiver noise added to the output, sinceg is non-zero.
)1(
)(
INR
FastronomyIPP RFI
Added noise power : -
RFI mitigation. Groningen, 2010
Cancellation Broadband adaptive filter
RFI mitigation. Groningen, 2010
Excision – Identify the RFI
The challenge is to find a characteristic which distinguishes the RFI from the “RFI-free” condition.
In time : test for RFI in S(t); S above some threshold.
In time/frequency : test for RFI in S(f,t)
Prior information :
Abandon polluted frequency channels
Spatial blanking – Null steering if the location of RFI sources is known or can be determined.
RFI mitigation. Groningen, 2010
Post-Correlation adaptive filter
RFI mitigation. Groningen, 2010
Cancellation Real-time adaptive filter
RFI mitigation. Groningen, 2010
ATCA – Kesteven & Manchester real-time single IF adaptive filter
RFI mitigation. Groningen, 2010
Types of RFI (2)
- Observatory-generated
computers
high-speed digital electronics
faulty equipment
RFI mitigation. Groningen, 2010
The Copy of the RFI
Some options:
• Use a reference antenna pointed directly towards the source of the RFI.
• RFI is distributed over the focal plane, unlike the astronomical field. Could use a multiple feed package to extract the RFI.
• GLONASS – using the published data.