Post on 19-Jan-2016
description
6-Channel Electronic Volume Controller IC Preliminary PT2258
Princeton Technology Corp.Tel : 886-2-29162151Fax: 886-2-29174598
URL: http://www.princeton.com.tw
PT2258 pre1.0 1 Updated July 2000
DESCRIPTION
PT2258 is a 6-Channel Electronic Volume Controller IC utilizing CMOS Technology specially designedfor the new generation of AV Multi-Channel Audio System. PT2258 provides an I2C Control Interface,an attenuation range of 0 to -79 dB at 1 dB/step, low noise, high channel separation. Housed in 20-pin,DIP or SO Package, PT2258’s pin assignments and application circuit are optimized for easy PCBLayout and cost saving advantages.
FEATURES
• CMOS Technology• Low Power Consumption• Least External Components• Attenuation Range: 0 to -79 dB at 1dB/step• Operating Voltage: 5 to 9 V• Low Noise, S/N Ratio>100dB (A-weighting)• High Channel Separation• I2C Bus Control Interface• Selectable Address• 6-Channel Outputs• Available in 20-pin, DIP or SO Package
APPLICATIONS
• AV Surround Audio Equipment• Car Audio• Mini Compo• Computer Multi-Media Speaker• Other Audio Equipments
6-Channel Electronic Volume Controller IC Preliminary PT2258
Princeton Technology Corp.Tel : 886-2-29162151Fax: 886-2-29174598
URL: http://www.princeton.com.tw
PT2258 pre1.0 2 Updated July 2000
BLOCK DIAGRAM
1 d B /s te p
1 d B /s te p
1 d B /s te p
1 d B /s te p
1 d B /s te p
1 d B /s te p
6-Channel Electronic Volume Controller IC Preliminary PT2258
Princeton Technology Corp.Tel : 886-2-29162151Fax: 886-2-29174598
URL: http://www.princeton.com.tw
PT2258 pre1.0 3 Updated July 2000
PIN CONFIGURATION
IN 1
IN 2IN 3
O U T 1
O U T 4
O U T 2
O U T 5
O U T 3
O U T 6
S C L R E F
S D A
C O D E 2 C O D E 1
G N D
D G N D V C C
1 2 0
2 1 9
3 1 8
4 1 7
8 1 3
1 0 11
7 1 4
9 1 2
6 1 5
5 1 6
P T 22 5 8
IN 4
IN 5
IN 6
6-Channel Electronic Volume Controller IC Preliminary PT2258
Princeton Technology Corp.Tel : 886-2-29162151Fax: 886-2-29174598
URL: http://www.princeton.com.tw
PT2258 pre1.0 4 Updated July 2000
PIN DESCRIPTION
Pin Name I/O Description Pin No.IN1 I Channel Input No. 1. 1
Connect a Capacitor to Audio SourceIN2 I Channel Input No. 2 2
Connect a Capacitor to Audio SourceIN3 I Channel Input No. 3 3
Connect a Capacitor to Audio SourceCODE2 - Refer to Address Code Section 4DGND - Digital Ground 5SCL I I2C Clock Input 6SDA I I2C Data Input 7IN4 I Channel Input No. 4 8
Connect a Capacitor to Audio SourceIN5 I Channel Input No. 5 9
Connect a Capacitor to Audio SourceIN6 I Channel Input No. 6 10
Connect a Capacitor to Audio SourceOUT6 O Channel Output No. 6 11
Connect a Capacitor to the Next StageOUT5 O Channel Output No. 5 12
Connect a Capacitor to the Next StageOUT4 O Channel Output No. 4 13
Connect a Capacitor to the Next StageGND - Ground 14REF - Reference Voltage= 1/2 Vcc 15
Connect a Capacitor to the GroundVCC - Power Supply Input 16
CODE1 - Refer to the Address Code Section 17OUT3 O Channel Output No. 3 18
Connect a Capacitor to the Next StageOUT2 O Channel Output No. 2 19
Connect a Capacitor to the Next StageOUT1 O Channel Output No. 1 20
Connect a Capacitor to the Next Stage
6-Channel Electronic Volume Controller IC Preliminary PT2258
Princeton Technology Corp.Tel : 886-2-29162151Fax: 886-2-29174598
URL: http://www.princeton.com.tw
PT2258 pre1.0 5 Updated July 2000
FUNCTIONAL DESCRIPTION
Bus Interface
Data are transmitted to and from the microprocessor to the PT2258 via the SDA and SCL. The SDAand SCL make up the BUS Interface. It should be noted that the pull-up resistors must be connected tothe positive supply voltage.
Data Validity
A data on the SDA Line is considered valid and stable only when the SCL Signal is in HIGH State.The HIGH and LOW States of the SDA Line can only change when the SCL signal is LOW. Pleaserefer to the figure below.
SDA
SCL
Start and Stop Conditions
A Start Condition is activated when 1) the SCL is set to HIGH and 2) SDA shifts from HIGH to LOWState. The Stop Condition is activated when 1) SCL is set to HIGH and 2) SDA shifts from LOW toHIGH State. Please refer to the timing diagram below.
SCL
SDA
6-Channel Electronic Volume Controller IC Preliminary PT2258
Princeton Technology Corp.Tel : 886-2-29162151Fax: 886-2-29174598
URL: http://www.princeton.com.tw
PT2258 pre1.0 6 Updated July 2000
Byte Format
Every byte transmitted to the SDA Line consists of 8 bits. Each byte must be followed by an Acknowl-edge Bit. The MSB is transmitted first.
Acknowledge
During the Acknowledge Clock Pulse, the master (µP) puts a resistive HIGH level on the SDA Line.The peripheral (audio processor) that acknowledges has to pull-down (LOW) the SDA line during theAcknowledge Clock Pulse so that the SDA Line is in a Stable Low State during this Clock Pulse. Pleaserefer to the diagram below.
The audio processor that has been addressed has to generate an Acknowledge after receiving each byte,otherwise, the SDA Line will remain at the High Level during the ninth (9th) Clock Pulse. In this case,the master transmitter can generate the STOP Information in order to abort the transfer.
Transmission without Acknowledge
If you want to avoid the acknowledge detection of the audio processor, a simpler µP transmission maybe used. Wait one clock and do not check the slave acknowledge of this same clock then send the newdata. If you use this approach, there are greater chances of faulty operation as well as decrease in noiseimmunity.
6-Channel Electronic Volume Controller IC Preliminary PT2258
Princeton Technology Corp.Tel : 886-2-29162151Fax: 886-2-29174598
URL: http://www.princeton.com.tw
PT2258 pre1.0 7 Updated July 2000
Interface Protocol
The interface protocol consists of the following:· A Start Condition· A Chip Address Byte including the PT2258 address. The 8th Bit of the Byte must be “0”. PT2258
must always acknowledge the end of each transmitted byte.· A Data Sequence (N-Bytes + Acknowledge)· A Stop Condition
Please refer to the diagram below:
Software Specification
PT2258 ADDRESS CODE
PT2258 Address Code depends on the state of CODE1 (Pin No. 17) and CODE2 (Pin No.4). If CODE1or CODE2 is connected to Vcc, then CODE1 or CODE2 is set to “1”. If CODE1 or CODE2 is con-nected to the Ground, it is set to “0”. Please refer to the information below:
Condition 1: When CODE1=”1” and CODE2=”1”:
PT2258 Address
CODE1 CODE2
1 1
Then, the PT2258 Address Code is (8CH):
1 0 0 0 1 1 0 0
MSB LSB
6-Channel Electronic Volume Controller IC Preliminary PT2258
Princeton Technology Corp.Tel : 886-2-29162151Fax: 886-2-29174598
URL: http://www.princeton.com.tw
PT2258 pre1.0 8 Updated July 2000
CODE1 CODE2
1 0
Then, the PT2258 Address Code is (88H):
Condition 2: When CODE1=”1” and CODE2=”0”:
CODE1 CODE2
0 1
Then, the PT2258 Address Code is (84H):
Condition 3: When CODE1=”0” and CODE2=”1”:
CODE1 CODE2
0 0
Then, the PT2258 Address Code is (80H):
Condition 4: When CODE1=”0” and CODE2=”0”:
1 0 0 0 1 0 0 0
MSB LSB
1 0 0 0 0 1 0 0
MSB LSB
1 0 0 0 0 0 0 0
MSB LSB
6-Channel Electronic Volume Controller IC Preliminary PT2258
Princeton Technology Corp.Tel : 886-2-29162151Fax: 886-2-29174598
URL: http://www.princeton.com.tw
PT2258 pre1.0 9 Updated July 2000
Data Bytes Description
FUNCTION BITS
MSB LSB FUNCTION
1 1 1 0 A3 A2 A1 A0 6-Channel, -1dB/step
1 1 0 1 0 B2 B1 B0 6-Channel, -10dB/step
0 0 0 1 A3 A2 A1 A0 Channel No. 3, -1dB/step
0 0 0 0 0 B2 B1 B0 Channel No. 3, -10dB/step
0 0 1 1 A3 A2 A1 A0 Channel No. 4, -1dB/step
0 0 1 0 0 B2 B1 B0 Channel No. 4, -10dB/step
0 1 0 1 A3 A2 A1 A0 Channel No. 2, -1dB/step
0 1 0 0 0 B2 B1 B0 Channel No. 2, -10dB/step
0 1 1 1 A3 A2 A1 A0 Channel No. 5, -1dB/step
0 1 1 0 0 B2 B1 B0 Channel No. 5, -10dB/step
1 0 0 1 A3 A2 A1 A0 Channel No. 1, -1dB/step
1 0 0 0 0 B2 B1 B0 Channel No. 1, -10dB/step
1 0 1 1 A3 A2 A1 A0 Channel No. 6, -1dB/step
1 0 1 0 0 B2 B1 B0 Channel No. 6, -10dB/step
1 1 1 1 1 0 0 M 6-Channel, MUTE
When M=1, MUTE=ON
When M=0, MUTE=OFF
6-Channel Electronic Volume Controller IC Preliminary PT2258
Princeton Technology Corp.Tel : 886-2-29162151Fax: 886-2-29174598
URL: http://www.princeton.com.tw
PT2258 pre1.0 10 Updated July 2000
ATTENUATION UNIT BIT
where: Ax=-1dB/step, Bx=-10dB/step
A3/--- A2/B2 A1/B1 A0/B0 ATTENUATION VALUE (dB)
0 0 0 0 0/0
0 0 0 1 -1/-10
0 0 1 0 -2/-20
0 0 1 1 -3/-30
0 1 0 0 -4/-40
0 1 0 1 -5/-50
0 1 1 0 -6/-60
0 1 1 1 -7/-70
1 0 0 0 -8/---
1 0 0 1 -9/---
ABSOLUTE MAXIMUM RATING
Symbol Parameter Rating Unit
Vs Supply Voltage 12 V
Tamb Ambient Temperature -20 to +75 oC
Tstg Storage Temperature -40 to +125 oC
6-Channel Electronic Volume Controller IC Preliminary PT2258
Princeton Technology Corp.Tel : 886-2-29162151Fax: 886-2-29174598
URL: http://www.princeton.com.tw
PT2258 pre1.0 11 Updated July 2000
ELECTRICAL CHARACTERISTICS
Symbol Parameter Condition Min. Typ. Max. Unit
VDD Supply Voltage 5 9 10 V
Is Supply Current 8 mA
RIN Input Impedance FL,FR,CTR 27 30 35 KΩSUB,SL,SR
VCL Maximum Input Voltage Volume=0dB 2.8 3.0 Vrms
THD=1%
Sc Channel Separation 90 100 110 dB
CRANGE Volume Control 79 dB
Range
AVMAX Maximum Attenuation -79 dB
Astep Attenuation Step 1 dB
EA Attenuation Error Volume=0~-50dB -1.0 0 +1.0 dB
AMUTE Mute Attenuation A-weighting 90 95 98 dB
THD Total Harmonic Volume=0dB 0.003 0.005 0.01 %
Distortion Input,200mVrms
Noise Output Noise A-weighting 3 5 µV
S/N Signal-to-Noise Ratio 0dB=1Vrms 100 105 110 dB
A-weighting
Ro Output Impedance 600 900 ΩGo Output Gain -0.5 0 +0.5 dB
Vomax Maximum Output FL,FR,CENTER 2.3 2.6 2.9 Vrms
SUB,SL,SR
THD=1%
I2C BUS SECTION ELECTRICAL CHARACTERISTICS
Symbol Parameter Condition Min. Typ. Max. Unit
VIL Bus Low Input Level 2.4 2.5 V
VIH Bus High Input Level 2.8 3.0 V
TINIT Bus Initialization Cref=10µF 250 300 mS
6-Channel Electronic Volume Controller IC Preliminary PT2258
Princeton Technology Corp.Tel : 886-2-29162151Fax: 886-2-29174598
URL: http://www.princeton.com.tw
PT2258 pre1.0 12 Updated July 2000
APPLICATION CIRCUIT
I N 1
I N 4
O U T 1
O U T 4
O U T 2
O U T 5
O U T 3
O U T 6
I N 2
I N 5
I N 3
I N 6
S C L R E F
S D A
C O D E 2 C O D E 1
G N D
D G N D V C C
V C C
P T 2 2 5 8
1 2 0
2 1 9
3 1 8
4 1 7
8 1 3
1 0 11
7 1 4
9 1 2
6 1 5
5 1 6
++
+ +
+
+
++
+ +
++
+ +
1 0 u f1 0 u f
1 0 u f 1 0 u f
1 0 u f
1 0 u f
1 0 u f1 0 u f
1 0 u f 1 0 u f
1 0 u f1 0 u f
1 0 u f 1 0 u f
1 0 0 K1 0 0 K
1 0 0 K 1 0 0 K
1 0 0 K1 0 0 K
1 0 0 K 1 0 0 K
1 0 0 K1 0 0 K
1 0 0 K 1 0 0 K
M C UI C B u s2
A d d r e s s = 8 8 H e x D G N D A G N D
C r e f
O U T P U TI N P U T
ORDER INFORMATION
Valid Part Number Package Type
PT2258 20 Pins, DIP Package (300 mil)
PT2258-S 20 Pins, SO Package (300 mil)
6-Channel Electronic Volume Controller IC Preliminary PT2258
Princeton Technology Corp.Tel : 886-2-29162151Fax: 886-2-29174598
URL: http://www.princeton.com.tw
PT2258 pre1.0 13 Updated July 2000
PACKAGE INFORMATION
20-Pin, DIP Package (300 mil)
Symbols Dimensions in InchesMin. Nom. Max.
A 0.210A1 0.015A2 0.115 0.130 0.195b 0.014 0.018 0.022b1 0.014 0.018 0.020b2 0.045 0.060 0.070b3 0.030 0.039 0.045c 0.008 0.010 0.014c1 0.008 0.010 0.011D 0.980 1.030 1.060D1 0.005E 0.300 0.310 0.325E1 0.240 0.250 0.280e 0.100 bsc
eA 0.300 bsc.eB 0.430eC 0.000 0.060L 0.115 0.130 0.150
6-Channel Electronic Volume Controller IC Preliminary PT2258
Princeton Technology Corp.Tel : 886-2-29162151Fax: 886-2-29174598
URL: http://www.princeton.com.tw
PT2258 pre1.0 14 Updated July 2000
Notes: 1. All dimensions are in INCHES.2. Dimensioning and tolerancing per ANSI Y14.5M-1982.3. Dimension “A”, ”A1” and “L” are measured with the package seated in JEDEC Seating
Plane Gauge GS-34. “D”, “D1” and “E1” dimensions do not include mold flash or protrusions. Mold flash or
protrusions shall not exceed 0.010 inch.5. “E” and “eA” measured with the leads constrained to be perpendicular to datum -c- .6. “eB” and “eC” are measured at the lead tips with the leads unconstrained.7. N is the number of terminal positions (N=20)8. Pointed or rounded lead tips are preferred to ease insertion.9. “b2” and “b3” maximum dimensions are not include dambar protrusions. Dambar protrusions
shall not exceed 0.010 inch (0.25mm).10. Distance between leads including Dambar protrusions to be 0.005 inch minimum.11. Datum plane -H- coincident with the bottom of lead, where lead exits body.12. Refer to JEDEC MS-001, Variation AD.
6-Channel Electronic Volume Controller IC Preliminary PT2258
Princeton Technology Corp.Tel : 886-2-29162151Fax: 886-2-29174598
URL: http://www.princeton.com.tw
PT2258 pre1.0 15 Updated July 2000
20-Pin, SO Package (300 mil)
Symbols Dimensions in MillimeterMin. Nom. Max.
A 2.35 2.65A1 0.10 0.30B 0.33 0.51C 0.23 0.32D 12.60 13.00E 7.40 7.60e 1.27 bsc.H 10.00 10.65h 0.25 0.75L 0.40 1.27α 0o 8o
Notes: 1. Dimensioning and tolerancing per ANSI Y14.5-1982.2. Dimension “D” does not include mold flash , protrusions or gate burrs. Mold Flash,
protrusion or gate burrs shall not exceed 0.15mm (0.006 in) per side.3. Dimension “E” does not include interlead flash or protrusions. Interlead flash or protrusions
shall not exceed 0.25 mm (0.010 in) per side.4. The chamfer on the body is optional. It is not present, a visual index feature must be located
within the crosshatched area.5. “L” is the length of the terminal for soldering to a substrate.6. “N” is the number of terminal positions. (N=20)7. The lead width “B” as measured 0.36 mm (0.014 in) or greater above the seating plane, shall
not exceed a maximum value of 0.61 mm (0.24 in).8. Controlling dimension: MILLIMETER.9. Refer to JEDEC MS-013 Variation AC