Post on 23-Apr-2020
@IJMTER-2016, All rights Reserved 128
Potential and development of solar drying technology: A Review
R.T. Ramteke1, C.N. Gangde
2 and S.R. Kalbande
2
1PhD Scholar Department. of Unconventional Sources of Energy and Electrical Engineering, CAET,
Dr.P.D.K.V., Akola, Maharashtra, India. 2Department. of Unconventional Sources of Energy and Electrical Engineering, CAET, Dr.P.D.K.V.,
Akola, Maharashtra, India.
Abstract- Solar energy is one of the promising heat sources for meeting energy demand without
putting adverse impact of environment. Hence it plays key role for sustainable development. This
paper presents developments and potentials of solar drying technology for drying of agriculture
produce. Detail description and fundamentals of different types of solar air heating systems like
natural convection direct dryer, forced circulation type dryer, green house type air heaters, solar
dryers with and without heat storage medium have been carried out and presented in present review
paper. It is found that natural circulation type solar tunnel dryer, wind ventilated type solar dryers
with heat storage units and green house dryers are more suitable for rural applications. The use of
solar collector’s performance enhancement technique accelerates drying rate and promotes overall
efficiency of drying system. Solar collectors works by absorbing the direct solar radiation and
converting it in to thermal energy which can be stored in the form of sensible heat or latent heat or a
combination of sensible and latent heat. During the investigation rock bed storages have been found
to be low type thermal heat storage, while phase change materials have been found to be higher heat
thermal storage. For better thermal performance of solar air heater with high latent heat and with
large surface areas for heat transfer required. The researcher’s designs going to the integration
between solar energy collection and thermal storage to reduce the loss, volume and system cost.
Key Words - Solar drying, phase change medium, latent heat storage, sensible heat storage
I. INTRODUCTION
Solar drying is promising and most preferred method for drying agricultural products. Drying
crops by solar energy is of great economic importance the world over. Solar energy being simple to
use, free, renewable, clean, non polluting and inexhaustible has received wide spread attention in
recent times. It provides well abundant energy source if utilized efficiently. But this energy is time
dependent energy source with an intermittent character. Most of the crops and grain harvests are lost
to fungal and microbial attacks these wastages could be easily prevented by proper drying, which
enhances storage of crops and grains over long periods of time. However, solar drying systems must
be properly designed to match particular drying requirements of specific crops, which can increase
the efficiency of a system.
The drying of agricultural produce under the sun is a common practice most especially in
developing countries like India where more than 3300 to 3700 hours of bright sunshine per year
available in North-West and West coastal regions of the country and 2900 hour over central part of
India except Kerala, Kashmir and Assam. In brief, there are nearly 250-300 days per year available
to get useful sunshine [1]. This method is characterized by a number of constraints like; lack of
process control, non-uniformity in the drying rate, soaking by rain, theft and vandalism,
contamination by dust, rodents, and other domestic animals . Also prolong open sun drying often
caused deterioration of vital ingredients like vitamins, minerals and sensory characters of dried
product and thus less market value Solar drying is alternative for drying varieties of agricultural
produce at superior drying rate compared to open sun drying method with improved quality of dried
product at a relative low cost.
Various types of solar air-heaters are being used for different applications; among them flat-
International Journal of Modern Trends in Engineering and Research (IJMTER) Volume 03, Issue 06, [June– 2016] ISSN (Online):2349–9745; ISSN (Print):2393-8161
@IJMTER-2016, All rights Reserved 129
plate collectors are extensively used in low-temperature solar energy, because they are relatively
simple, easy to operate and have low capital costs. Solar air heaters have many attractive advantages
over liquid heaters regarding the problems of corrosion, boiling, freezing and leaks. Solar air heater
without thermal storage is extensively used for drying agriculture products. Basically most of the
agriculture products are getting dried at low temperature (50–60 0C) and this can be easily achieved
in flat-plate type solar air heater.
There are many types and designs of solar dryers available for drying of agricultural
commodity. They mainly include natural convection cabinet dryer and forced circulation solar dryer
based on array of flat plate air heaters. The main drawbacks of forced circulation solar dryer are
requirement of more ground space under air heating array, high power requirement to circulate the air
and the high initial cost. The mechanical (fuel) operated dryer are more efficient than open sun
drying, provide uniform high quality dried produce, with many more advantages. The limitation of
this drier is that it cannot be used in the areas where electricity is not available. The major drawbacks
of natural convection dryer are higher drying time, uneven drying and comparatively low capacity.
Indirect dryers are suitable for colour sensitive produce, as the produce is not exposed directly to the
sun. These types of dryer are suitable for drying various industrial products, fruits, vegetables and
spices like turmeric, ginger etc.
This paper presents the potentials of direct solar dryers, indirect solar dryers, solar dryers
with heat storage media, solar dryers without heat storage media, solar tunnel dryers for solar drying
of fruits, vegetables, spices, cereals, grain, legumes, medicinal plants, fish etc, with a view to
providing some of the benefits to farmers.
1.1 Classification of Solar Dryers
The dryer can be classified into two major groups, namely:
a) Passive solar-energy drying systems (conventionally termed natural-circulation solar drying
systems) and,
b) Active solar-energy drying systems (most types of which are often termed hybrid solar dryers).
Three distinct sub-classes of either the active or passive solar drying systems can be
identified namely:
• Direct-type solar dryers;
• Indirect-type solar dryers; and
• Hybrid solar dryers.
Solar energy dryers can broadly be classified into direct, indirect and hybrid solar dryers.
The working principle of these dryers mainly depends upon the method of solar- energy collection
and its conversion to useful thermal energy for drying.
1.1.1 Direct Solar Drying (DSD)
Here the moisture is taken away by the air entering into the cabinet from below and escaping
through at the top exit as shown in Figure 1.1 Sharma [2]
“Figure 1. Working principle of direct solar drying”
International Journal of Modern Trends in Engineering and Research (IJMTER) Volume 03, Issue 06, [June– 2016] ISSN (Online):2349–9745; ISSN (Print):2393-8161
@IJMTER-2016, All rights Reserved 130
1.1.2 Indirect Solar Drying (ISD)
The crops in these indirect solar dryers are located in trays or shelves inside an opaque
drying cabinet and a separate unit termed as solar collector is used for heating of the entering air into
the cabinet. Shown in Fig. 1.2 Sharma [2]
“Figure 2. Working principle of indirect solar drying system”
1.1.3 Hybrid Solar Drying (HBD)
The hybrid solar dryers combine the features of the direct and indirect type solar- energy
dryers. Here the combined action of incident direct solar radiation on the product to be dried and air
pre-heated in a solar collector heater produces the necessary heat required for the drying process.
II. NATURAL CONVECTION SOLAR DRYER
In the natural convection solar dryers the airflow is established by buoyancy induced airflow
while in forced convection solar dryers the airflow is provided by using a fan either operated by
electricity/solar module or fossil fuel. Natural convection solar drying has advantages over forced
convection solar drying, one of which is that it requires a lower investment. Due to low cost and
simple operation and maintenance, natural convection solar dryer appears to be the obvious option
and popular choice for drying of agricultural products. In such a dryer, the crop is contained within a
cabinet in a relatively thin bed, air flows as a result of the buoyancy forces resulting from the
temperature differences up through the crop bed. The drying rates achieved to date with these dryers
have not, generally, been very satisfactory .
The simplest of solar cabinet dryer was reported by Fudholi et al. [3], it was very simple,
and consists essentially of a small wooden hot box. Dimensions of this dryer was 2 m × 1 m where
the sides and bottom were constructed from wood and metal sheets. A transparent polyethylene sheet
was used as cover at the upper surface. Air holes were located on the sides of the dryer for
circulation.
Singh et al. [4] investigated a small size domestic natural convection solar dryer. It is mainly
consists of a hot box, base frame, trays and shading plates. A transparent window glass (4 mm thick)
was fixed as glazing. It was fixed to the hot box with an aluminum angle. In order to provide air
circulation in the dryer, 40 holes with total area of 0.002 m2 were drilled in the top and sides of the
dryer. A flat sheet of 5 cm thick of thermocole was used as insulator. Mursalim et al. [5] evaluated a
modified cabinet dryer with natural convection system. The dryer had a single transparent plastic
cover and the sawdust was used as an insulating material. The drying chambers walls were build of
plywood painted black with dimensions 120 cm × 80 cm × 40 cm (long, width, and height). For air
flow, 12 holes were provided at the bottom.
Ezekoye and Enebe [6] evaluated a domestic direct mode solar dryer with
constructed components mounted on a skeleton and screwed such that the various components are
detectable and dismantled for easy movement. Optimum temperature of 67.0°C is achieved with
the dryer at no-load test and could dry pepper and groundnuts for a maximum of five and eight days
respectively.
International Journal of Modern Trends in Engineering and Research (IJMTER) Volume 03, Issue 06, [June– 2016] ISSN (Online):2349–9745; ISSN (Print):2393-8161
@IJMTER-2016, All rights Reserved 131
2.1.1 Natural circulation greenhouse dryers
These are also called as tent dryers and are basically modified greenhouses. They are
designed with vents of appropriate size and position to have a controlled air flow. They are
characterized by extensive glazing by the transparent cover of polyethylene sheet. Fig.3 shows the
earliest form of passive solar greenhouse dryer by the Brace Research Institute, with slanted glass
roof, allowing direct solar radiation over the product. The length-wise north-south alignment of the
dryer had black coated internals for improved absorption of solar radiation with the ridge-cap over
the roof for exit vent. Doe et al. [7] later designed the widely reported poly-ethylene tent dryer,
illustrated in Fig.4 consisting of a ridged bamboo framework clad with a clear polythene sheet over
it. A black poly-ethylene sheet was also spread on the floor inside the tent to enhance the absorption
of solar radiation. The air flow into the tent was controlled by rolling/ unrolling of the cladding at the
bottom edge of front side and the vents at the top served as the exit for the moist exhaust air.
Sachithananthan et al. [8] reported a horticultural greenhouse of clear plastic sheet cladding over a
semi-cylindrical metal frame (Fig.5). The modification were with a black galvanized iron sheet
absorber at floor, inlet vents along the full length of both sides of base and exit with plastic nets at
the top to protect from insects and dust.
Fleming et al. [9] reported a typical greenhouse type solar dryer with a transparent semicylindrical
chamber with a cylindrical solar chimney posted vertically at one end and a door for air inlet and
access to the chamber at other end as shown in Fig.6.
Rathore et al. [10] has conducted various experimental studies on a modified design of
hemicylindrical solar tunnel dryer for drying of grapes also few researchers have used a
polycarbonate cover for its construction. Afriyie et al. [11] has reported the study of simulation
and optimization of a chimney ventilated solar crop dryer.
Kalbande et al. [12] designed and fabricated a solar-biomass hybrid dryer. A biomass
combustor retrofitted to natural convection solar tunnel dryer used solar energy for drying during day
time and Prosopis juliflora as fuel in biomass combustor cum hot air generator during off sunshine
hours and thus extends the working time of the dryer. Experiments have been conducted to test the
performance of the dryer, turmeric had been dried. The results indicate that the drying is faster. The
quantitative analysis showed that the traditional drying i.e. open sun drying took 4 to 15 days to dry
the rhizomes while solar biomass drier took only 1.5 to 4 days for the samples having different
treatments and produced better quality produce. The maximum efficiency of biomass combustor and
solar-biomass hybrid dryer was found to be 79.79 and 14.00 respectively.
“Figure 3. Natural-circulation glass-roof “Figure 4. Natural-circulation polythene tent
dryer solar-energy dryer”
International Journal of Modern Trends in Engineering and Research (IJMTER) Volume 03, Issue 06, [June– 2016] ISSN (Online):2349–9745; ISSN (Print):2393-8161
@IJMTER-2016, All rights Reserved 132
“Figure 5. Natural-circulation solar “Figure 6. A greenhouse type natural circulation
dome dryer” solar–energy dryer”
2.2 Forced convection solar dryers
Adding a small fan powered by a photovoltaic system to provide the required air flow will
give drying rates much higher than those achieved by an indirect natural convection solar
dryer. Various design of indirect solar dryer had been developed and tested. These designs had been
recommended for commercial purposes. The indirect type solar dryers include the chamber-type
dryers (tray and rack type dryer, bin type, and tunnel type), chimney-type dryers and wind-ventilated
dryers. Solar dryer which have demonstrated their potentialities for small-scale agro-industrial
applications are discussed below.
Bolaji [13] investigated an indirect solar dryer using a box type absorber collector. The
dryer consists of an air heater, an opaque crop bin, and a chimney. The box-type absorber collector,
made of a glass cover and black absorber plate, was inclined at angle of 200 to the horizontal to allow
the heated air to rise up the unit with little resistance. He reported that the maximum efficiency
obtained in the box-type absorber system was 60.5%. He found also that the maximum average
temperatures inside the collector and drying chamber were 64 and 57 ◦C, respectively; while, the
maximum observed ambient temperature was 33.50C.
Al-Juamily et al. [14] constructed and tested an indirect-mode forced convection dryer for
drying fruits and vegetables in Iraq. The solar dryer consists of a solar collector, a blower, and a
solar drying cabinet. Two identical air solar collectors having V-groove absorption plates of two air
passes and a single glass cover were used. The total area of the collectors was 2.4 m2. Two types of
fruits and one type of vegetables were dried using this dryer. These were grapes, apricots, and beans.
The moisture content of apricot had been reduced from 80% to 13% within one day and a half of
drying. Moreover, the moisture content of grapes had been reduced from 80% to 18% in two and a
half days of drying. Finally, the beans moisture content had been reduced from 65% to 18% in 1 day
only. They concluded that the air temperature is the most effective factor on drying rate. The effect of
variation of the speed of air inside the drying cabinet was small and may be neglected.
Karim and Hawlader [15] studied the V-groove, fins and flat-plate collectors for crop drying
applications. The results showed that the V-groove collector had 7–12% higher efficiency than flat-
plate collector. The double pass operation of the collector improved the efficiency of all three
collectors. The efficiency of all the air collectors is a strong function of airflow rate. The flow rate
0.035 (kg/m2
s) was considered optimal for solar drying of agricultural product.
International Journal of Modern Trends in Engineering and Research (IJMTER) Volume 03, Issue 06, [June– 2016] ISSN (Online):2349–9745; ISSN (Print):2393-8161
@IJMTER-2016, All rights Reserved 133
“Figure 7. Schematic description of the solar air heater (a) cross-section view perpendicular to the flow direction; (b)
cross-section view along the flow direction; and (c) schematic description of the cross-corrugated absorbing plate and
bottom plate [53]”.
Sarsilmaz et al. [16] conducted experiments on drying of apricots in a newly developed rotary
column cylindrical dryer (RCCD) equipped with a specially designed air solar collector to find the
optimum drying air rate and rotation speed of dryer, to maintain uniform and hygienic drying
conditions and to reduce drying times. The systems were constituted of three parts: air blow region
(fan), air heater region (solar collector) and drying region (rotary chamber).
Ehiem et al. [17] designed and developed an industrial fruit and vegetable dryer consisting
of a drying chamber, blower and heat exchanger unit for reducing vegetable wastage and improving
their storage conditions. Using tomatoes of small, medium and large sizes; mean drying capacity of
258.64 kg for tomatoes per batch at an average drying chamber temperature of 50°C and varying air
flow rates (18.3 m/s, 18.8 m/s and 19.5 m/s); drying time and drying rate of 0-14 hr and 40 g/hr were
achieved respectively with thermal efficiency of 84 %.
Bolaji et al.[18] utilized the benefits of using a rotary wind ventilator for forced convection
solar dryer in remote area where electricity and other power sources are non- existent. The dryer is
made of solar air-heater of black absorber plate insulated with foam material to minimize heat losses.
An absorber mesh screen is place midway between the glass cover and the black absorber plate for
effective air heating as solar radiation that passes through the transparent cover is absorbed by both
the mesh and black-plate. The drying chamber holds drying trays in layers, a rotary wind ventilator
located at the top circulates the heated air in the drying chamber. The performance of the dryer with
and without the wind ventilator led to considerable reduction in drying time and increased system
efficiency in comparison to open sun drying method.
Bala et al [19] dried pineapple using solar tunnel drier at Bangladesh Agricultural University,
Mymensingh, Bangladesh. The drier consists of a transparent plastic covered flat plate collector and
a drying tunnel connected in a series to supply hot air directly into the drying tunnel using two d.c
fans operated by a solar module. With a loading capacity of 120-150kg and 8 experimental tests, the
use of the solar tunnel drier leads to considerable reduction in drying time in comparison to open sun
method and dried products were completely protected from contamination. Also, the proximate
analysis indicates that dried products were of good quality compared to open sun dried products.
2.3 Solar dryers without heat storage system
A widespread literature reviewed various types of solar air heater without thermal storage and
presented in this section.
International Journal of Modern Trends in Engineering and Research (IJMTER) Volume 03, Issue 06, [June– 2016] ISSN (Online):2349–9745; ISSN (Print):2393-8161
@IJMTER-2016, All rights Reserved 134
Chandrakumar and Jiwanlal [20] developed and evaluated the performance of a forced
convection mixed-mode solar dryer using smooth and rough plate solar collectors. The study was
conducted to compare the performance of the smooth and the roughed plate collectors in conducting
drying. The thermal performance of the smooth solar collector was found to be poorer because
of low convective heat transfer from the absorber plate to air. Artificial rib roughness on the
underside of the absorber plate has been found to considerably enhance the heat transfer coefficient.
Under no-load conditions the roughed absorber plate of the dryer attained a temperature of
69.2°C when it was studied. The maximum air temperature in the dryer under this condition was
64.1°C. The dryer could dry 3 kg of grapes having an initial moisture content of 81.4% to final
desired moisture content of 18.6% within 4 days while it was 8 days for open sun drying. Sahu and Bhagoria [21] reported effect of broken transverse ribs on absorber plate of a solar
air heater. Integral rib roughened absorber plates were prepared by fixing wires of 1.5 mm diameter
over one side of absorber plate. Roughness geometry was having pitch (P) ranging from 10 to 30
mm, height of rib (e) was 1.5 mm and duct aspect ratio was 8. Investigated range of Reynolds
number was 3000–12,000. Heat transfer coefficient enhancement over smooth duct was reported to
be 1.25–1.4 times and maximum thermal efficiency of the order of 83.5% was obtained.
Saravanakumar and Mayilsamy [22] have presented the thermal performance of flat plate solar
air heater (FP-SAH) with and without thermal storages. A forced convection solar collector
integrated with the different SHS material was developed and tested for its performance. The system
consists of a FP-SAH with heat storage unit and a centrifugal blower to increase collector and 𝜂
(10–20%). Gravel with iron scraps gives better efficiency than other storage materials. Forced
convection solar collector was more suitable for drying high quality dried product even in a cloudy
climate.
Chabane et al. [23] investigated thermal performance of a single pass solar air heater with fins
attached. Longitudinal fins were used inferior to the absorber plate to increase the heat exchange and
render the flow fluid in the channel uniform. The effects of mass flow rate of air on the outlet
temperature, the heat transfer in the thickness of the solar collector and thermal efficiency were
studied. Experiments were performed for an air mass flow rate of 0.012 kg/s. Maximum efficiency
was obtained by using five longitudinal fins and without using fins. The maximum efficiency levels
obtained for the 0.012 kg/s with and without fins were 40.02% and 34.92% respectively. A
comparison of the results of the solar collector with and without fins shows a substantial
enhancement in thermal efficiency.
Several research works have been explored for dryers having thermal energy storage
materials either under the collector absorber plate or integrated to the drying chamber for accelerated
drying process. The various forms in which thermal energy can be stored are sensible heat, latent
heat, thermo chemical or combinations of these. The following sections discuss each of these forms
in detail.
2.4 Solar dryers with heat storage system
Gutti et al [24] designed and constructed a natural/forced convection solar vegetable dryer
using locally available materials and incorporated with a heat storage unit for ensuring drying
during night hours. The solar collector absorber plate was made of corrugated aluminium,
painted black to improve its absorption and insulated with thick plywood to prevent heat loss. The
drying cabinet structural frame was built from a well- seasoned gmelina wood and plywood sheet
and outlet vent (chimney) provided towards the upper end at the back of the cabinet to facilitate and
control the convection flow of air through the dryer. Forced convection drying system gave higher
drying capabilities compared to the natural convection system and the stored useful heat used
for about six hours in drying during the night.
Ayyappan and Mayilsamy [25] integrated a natural convection solar tunnel dryer with
sensible heat storage material (sand) for copra drying. Experiments were performed with and
without the heat storage material. The system reduced the moisture content of copra from
52% (w.b.) to 7.2% (w.b.) in 52 hrs and 78 hrs respectively with and without the heat storage
International Journal of Modern Trends in Engineering and Research (IJMTER) Volume 03, Issue 06, [June– 2016] ISSN (Online):2349–9745; ISSN (Print):2393-8161
@IJMTER-2016, All rights Reserved 135
material. It also produces copra of high quality and market value for the farmers than the sun dried.
In open sun method, moisture content was reduced from 52.3% (w.b.) to about 7.8% in 172 hrs. The
average solar tunnel drier thermal efficiency was estimated to be about 18% in both drying modes.
Jain [26] presented a transient analytical model to study solar crop dryer having reversed
absorber plate type collector and thermal storage with natural flow. The developed model was solved
to compute the air temperature and various functional components of the drying systems for the
climatic condition of Delhi, India. The parametric study involved the effect of width of airflow
channel and height of packed bed on the crop temperature. A reversed absorber plate of 1m length
with 0.15 m packed bed could dry 95 kg of onions from a moisture content of 6.14 to 0.27 kg
water/kg of dry matter in a 24 hrs drying period.
2.4.1 Sensible Heat Storage
Sensible heat is stored by raising the temperature of a solid or liquid media. Some of the solid
mediums used are metals, rock, concrete and liquid medium are oil-based liquids, water, and molten
salts.
Singh and Bansal [27] fabricated solar air heater from broken glass pieces and evaluated with
four typical cases (i) top surface blackened, (ii) all glass pieces blackened and (iii) bottom surface
blackened. From the study it was concluded that the efficiency of all three systems goes on
increasing with increasing mass flow-rate. Porous types of air heaters always give better performance
over the nonporous types, since the bottom absorbing type of air heater is better than the top
absorbing type of air heater. For the case of non-porous types of air heating collectors, the thin and
thick absorbing plates are better for bsorption at the top and bottom, respectively, while a porous type
air heater has an optimum plate thickness (i.e. 0.05 m).
Tiwari et al. [28] have experimentally evaluated a crop dryer cum water heater and crop dryer
rock bed storage. They reported energy balance equations for each component of the system have
been used to predict the analytical results. On the basis of the analytical results, it is observed that the
drying time is significantly reduced due to the increase in thermal energy on the collector by the
reflector. The system can be used to provide hot water in case the drying system is not in operation.
The water heater below the air heater systems will act as a storage material for drying the crop during
off-sunshine hour.
Chauhan et al. [29] studied the drying characteristics of coriander in a stationary 0.5
tone/batch capacity deep-bed dryer coupled to a solar air heater and a rock bed storage unit that is to
receive hot air during sunshine and off-sunshine hours, respectively. The theoretical investigation
was made by writing the energy and mass balance equations for different components of the dryer-
cum-air-heater-cum-storage and by adopting a finite difference approach for simulation. The results
revealed that for reducing the moisture content 28.2% (db) to 11.4% (db) the solar air heater takes 27
cumulative sunshine hours, i.e. about 3 sunshine days, whereas the solar air heater and the rock bed
storage combined take 31 cumulative hours, i.e. about 2 days and 2 nights at an air flow velocity of
250 kg/h m2, and recommended that the heat stored in the rock bed can be used effectively for
heating the inlet (ambient) air for off-sunshine drying of agricultural products.
Shanmugam and Natarajan [30] studied regenerative desiccant integrated solar dryer with and
without reflective mirror. An indirect forced convection with desiccant integrated solar dryer had
been built and tested. The main parts were: a flat plate solar air collector, a drying chamber, desiccant
bed and a centrifugal blower. The system was operated in two modes, sunshine hours and off
sunshine hours. During sun shine hours the hot air from the flat plate collector is forced to the drying
chamber for drying the product and simultaneously the desiccant bed receives solar radiation directly
and through the reflected mirror. In the off sunshine hours, the dryer was operated by circulating the
air inside the drying chamber through the desiccant bed by a reversible fan. The dryer was used to
dry 20 kg of green peas and pineapple slices.
Mohanraj and Chandrasekar [31] performed an indirect forced convection solar drier
integrated with heat storage material; it was designed, fabricated and investigated for copra drying.
One side of the collector was connected to the blower with the help of reducer and the other side was
International Journal of Modern Trends in Engineering and Research (IJMTER) Volume 03, Issue 06, [June– 2016] ISSN (Online):2349–9745; ISSN (Print):2393-8161
@IJMTER-2016, All rights Reserved 136
attached with drier cabin as shown in Fig.8. The 100-mm gap between the absorber and insulation
was filled with sand mixed with aluminum scraps to store the heat during sunshine hours and to
obtain hot air during off sunshine hours. The experiments with heat storage material were conducted
for 8 h during potential sunshine hours and 4 h during lean or off sunshine hours the chili was dried
from initial moisture content 72.8% to the final moisture content about 9.2% and 9.7% (wet basis) in
the bottom and top trays, respectively. Thermal efficiency of the solar drier was estimated to be about
21% with specific moisture extraction rate of about 0.87 kg/kWh.
“Figure 8. Schematic of solar air heater integrated with storage unit used for copra drying [41]”.
Kamble et al. [32] Studied drying of chilli using solar cabinet dryer coupled with gravel bed
heat storage system. The solar cabinet dryer coupled with gravel bed heat storage system was
evaluated for drying of green chilli. The loading capacity of the dryer was about 15 kg of fresh
produce per batch. An exhaust fan was provided in the drying chamber. The average temperature was
observed in the range of 25 to 55°C. Drying time for drying green chilli from initial moisture content
of 88.5% (w.b) to 7.3% (w.b) was estimated to be 56 h in solar dryer whereas 104 h was observed in
the open sun drying. Drying time due to introduction of heat storage system was extended by 4 h
after sunset. Drying efficiency of the solar cabinet dryer was found to be 34 %.
Saxena et al. [33] designed and carried out performance of a solar air heater with long term
heat storage system. ‘‘Granular carbon’’, has introduced as a long term heat absorbing media inside
solar heater. The thermal performance evaluation of solar heater has been carried out on four
different configurations by operating it on natural and forced convection. The thermal behavior of the
system has also been evaluated by operating it on auxiliary power by placing a halogen tube (300 W)
inside the inlet and outlet ducts. Because of using halogen lights the system is feasible to perform in
night or bad climatic conditions. The thermal performance of all new configurations was found better
in comparison of conventional solar air heater on both natural and forced convection.
2.4.2 Latent Heat Storage
Solar air heater with PCM (Phase change media) based thermal storage system is the solar
energy collection for it’s off sunshine hours use. A phase change material is a solid and melted
which stores energy. The melting temperature may be fixed or may vary over a small range. The
stored energy is recovered upon solidification of the liquid. In this system, solar energy stored in
thermal energy storage system (TESS), during sunny days and recovered later at night or during
cloudy days.
Farid et al. [34] constructed a latent heat storage module consisting of 45 cylindrical capsules
fixed vertically in 15 rows. The capsules made of copper tubes 0.335-m long and external diameters
International Journal of Modern Trends in Engineering and Research (IJMTER) Volume 03, Issue 06, [June– 2016] ISSN (Online):2349–9745; ISSN (Print):2393-8161
@IJMTER-2016, All rights Reserved 137
of 31.8 mm were fixed in an insulated rectangular duct. Three commercial waxes having melting
temperatures of 44 0C, 53
0C, and 64
0C were selected. Each of the three sets of 15 tubes was filled
with different wax. For comparison purposes, experiments were also done with a single commercial
wax, having a melting temperature of 53 0C, in all the tubes. During heat charge, hot air flowed
across the capsules such that the melting temperature of the waxes decreased in the flow direction.
Air flow direction was reversed during heat discharge. Experimental measurements showed some
improvement in the heat transfer rates during both heat charge and discharge when three types of
PCMs were used. There was no improvement in the heat transfer rate during the sensible heat storage
period, while a maximum increase of 15% was observed during the latent heat period.
Fatah [35] developed a simple solar air heater integrated with thermal energy storage system.
A set of copper tubes were filled with thermal energy storage material and placed as an absorber.
Different sensible heat and latent heat storage materials were studied. The results indicated that the
heater filled with PCMs with 51 and 43 0C melting temperatures gives the best performance;
otherwise the system daily average efficiency varies between 27% and 63%.
Fath [36] designed and analyzed thermal performance of a simple design solar air heater with
built-in thermal energy storage system. The heater absorber consists of a corrugated set of tubes filled
with a phase change material (paraffin wax) as a thermal energy storage material. In this study, the
absorber projected area was used 1.0 m2, the length being 150 cm and the width 67 cm. The depth of
the heater is taken to be equal to 7.5 cm. The system shows a 63.35% daily average efficiency an air
flow rate of 0.02 kg/s, and the hot air outlet temperature (50C above ambient temperature) extended
for about 16 h, as compared to 38.7% and 9 h, respectively, for the conventional flat plate air heater.
For an air flow rate of 0.01 kg/s, the hot air outlet temperature continues for 21 h of the 24 h/day.
Enibe [37] have been designed and evaluated the performance (on natural convection) of
a passive solar powered air heating system which had potential applications in crop drying and
poultry egg incubation that consist of single-glazed flat plate solar collector (FPSC) integrated with
paraffin type PCM heat storage system. The phase change material (PCM) was prepared in modules
equispaced across the absorber plate. The system was tested under daytime no-load conditions with a
ambient temperature range of 19 0C– 41
0C and a daily global irradiation range of 4.9–19.9 MJ m
-2.
The peak temperature rise of the heated air was about 15 0K, while the maximum airflow rate and
peak cumulative useful efficiency were about 0.058 kg s−1
and 22%, respectively.
Takakura and Nishina [38] tested polyethylene glycol and CaCl2 ·6H2 O as PCMs in
greenhouse heating for 7.2 m2 ground area. They compared conventional greenhouses with PCM
storage type greenhouses. The efficiency of the greenhouse with PCM stor- age integrated with
solar collector was 59% and able to maintain 8 0C inside the greenhouse at night, when the outside
temperature dropped to −0.6 0C. A microcomputer control system has been developed in order to
establish more accurate and more sophisticated control for solar greenhouse systems.
Benli and Durmus [39] studied the thermal performance of solar air collectors heating system
with phase change material for space heating of a greenhouse. CaCl2·6H2O was used as PCM in
thermal energy storage with a melting temperature of 29 0C. In this system, the hot air delivered by
10 pieced solar air collectors was passed through the PCM to charge the storage unit. The stored heat
was utilized to heat ambient air before being admitted to a greenhouse. Through this study, they
concluded that the solar air collectors and PCM system created 6–9 0C temperature difference
between the inside and outside the greenhouse. The system worked more efficiently in day with high
solar radiation air temperatures. The proposed size of collectors integrated PCM provided about 18–
23% of total daily thermal energy requirements of the greenhouse for 3–4 h, in comparison with the
conventional heating device.
III. CONCLUSIONS
A review of potential and development of solar air heater for natural convection direct solar
dryer, forced circulation indirect type solar dryers, tunnel type solar dryers, solar dryers without heat
storage material, air heating system with sensible and latent heat storage material have been carried
International Journal of Modern Trends in Engineering and Research (IJMTER) Volume 03, Issue 06, [June– 2016] ISSN (Online):2349–9745; ISSN (Print):2393-8161
@IJMTER-2016, All rights Reserved 138
out and concluded that Cabinet type dryer may be useful for domestic applications for drying fruits
and vegetables. For preservation of nutrients of dried products, indirect type forced convection solar
dryers are preferred and therefore recommended for drying mostly perishables. These indirect type
forced convection solar dryers have superior drying rate but their power requirement renders them
inappropriate for rural and small scale operations.
Since solar air heater is the most important component of the indirect solar drying system,
improvement of the solar air heater would led to better performance of the drying system. Therefore;
more studies to investigate and improve the thermal performance of double pass flat, V- corrugated
and finned plate solar air heater is still of considerable interest. The integration of heat storage units
in drying systems accelerates drying during low intensity solar radiation periods and night hours.
The use of sensible heat storage materials is most preferred due to their availability, simplicity in
construction and low cost.
The natural-circulation type solar tunnel dryers, wind ventilated type solar dryers with heat
storage units and greenhouse dryers have the advantage of low cost and simplicity in both on-
the-site construction and operation and therefore recommended for rural applications. For a better
thermal performance of solar air heater a phase change material with high latent heat and with large
surface area for heat transfer is required. The researcher’s designs going to the integration between
solar energy collection and thermal storage to reduce the heat loss, volume and system cost.
REFERENCES
[1] A.Mani, New dimensions in renewable energy. Proceedings of NSES-92, IIT Delhi,;23-29, 1992.
[2] Sharma, A., Chen, C. R., Lan, N. V., Solar-energy drying systems: A Review: Renewable and Sustainable Energy
Reviews.13:1185-1210, 2009.
[3] Fudholi A, Sopian K, Ruslan M H, Alghoul MA, Sulaiman MY, Review of solar dryers for agricultural and marine
products. Renewable and Sustainable Energy Reviews. 14:1–30, 2010.
[4] Singh P P, Singh S, Dhaliwal S. S, Multi-shelf domestic solar dryer. Energy Conversion & Management. 47:1799–
815, 2006.
[5] Mursalim, Supratomo, Dewi Y S, Drying of cashew nut in shell using solar dryer. Science & Technology.3(2):25–
33, 2002.
[6] Ezekoye B. A. and Enebe O. M., Development and performance evaluation of modified integrated passive solar
grain dryer. The Pacific Journal of Science and Technology. 7:185-190, 2006.
[7] Doe, P. E., Ahmed, M., Muslemuddin, M., Sachithananthan, K. A , A polythene tent dryer for improved sun drying
of fish, Food Tech Aust. 29: 437-441, 1977.
[8] Sachithananthan, K., Trim D., Speirs C I ,A solar dome dryer for drying of fish, FAO Fisheries Paper, Rome, Italy.
RAB/81/002/INT/L8. 1983.
[9] Fleming, P. D., Norton. B., Ekechukwu, O. V., Onyegegbu, S. O., Probert, SD, A large-scale facility for
experimental studies of natural-ciruclation solar- energy tropical crop dryers. In: Proc Int Drying Symp (Drying '86).
Cambridge, Mass., U.S.A., Hemisphere Pub Coy Washington. 685-693,1986.
[10] Rathore, N.S.and Panwar, N L, Experimental studies on hemi cylindrical walk-in type solar tunnel dryer for grape
drying, Applied Energy. 87: 2764-2767,2010.
[11] Afriyie, J. K., Rajakaruna, H., Nazha, M. A. A., Forson, FK X Simulation and optimization of the ventilation in a
chimney-dependent solar crop dryer, Solar Energy, 85: 1560-1573,2010.
[12] Kalbande, S.R., C.N.Gangde and A.Dhondage, Techno-economic evaluation of solar-biomass hybrid drying system
for turmeric (Curcuma longa L.). FIRE Journal of Science and Technology. 2: 97-107, 2013.
[13] Bolaji B.O., Development and performance evaluation of box- type absorber solar air collector for crop
drying. Journal of Food Technology. 3(4):515– 600,2005.
[14] Al-Juamily KEJ, Khalifa AJN, Yassen T. A., Testing of performance of fruit and vegetable solar drying
system in Iraq.Desalination. 209:163–70, 2005.
[15] Karim M A, Hawlader MNA, Development of solar air collectors for drying applications. Energy Conversion &
Management. 45:329– 344 ,2004.
[16] Sarsilmaz C, Yildiz C, Pehlivan D., Drying of apricots in a rotary column cylindrical dryer (RCCD) supported
with solar energy. Renewable Energy. 21:117– 127,2000.
[17] Ehiem J.C., Irtwange S.V and Obetta S.E., Design and Development of an Industrial Fruit and Vegetable Dryer.
Research Journal of Applied Sciences, Engineering and Technology. 1(2):44-53,2009.
[18] Bolaji B.O, Olayanjub T.M.A and Falade T.O., Performance Evaluation of a Solar Wind-Ventilated Cabinet
Dryer. Western Indian Journal of Engineering.33(1/2):12-18,2011.
[19] Bala B.K, Mondol M.R.A, Biswas B.K and Das Chowdury B. L., Solar drying of Pineapple using Solar
Tunnel Drier. 4th International Conference on Mechanical Engineering, December 26-28, Dhaka, Bangladesh:47-
International Journal of Modern Trends in Engineering and Research (IJMTER) Volume 03, Issue 06, [June– 2016] ISSN (Online):2349–9745; ISSN (Print):2393-8161
@IJMTER-2016, All rights Reserved 139
51,2001.
[20] Chandrakumar B Pardhi and Jiwanlal L Bhagoria, Development and performance evaluation of mixed-mode solar
dryer with forced convection.International Journal of Energy and Environmental Engineering.2 (23):1-8,2013.
[21] Sahu, M.M. and J.L. Bhagoria, Augmentation of heat transfer coefficient by using 90 broken transverse ribs on
absorber plate of solar air heater. Renewable Energy. 30:2057–63,2005.
[22] Saravanakumar, P.T. and K. Mayilsamy, Forced convection flat plate solar air heaters with and without thermal
storage. Journal of Scientific and Industrial Research. 69(12): 966–968,2010.
[23] Chabane Foued, Noureddine Moummi and Said Benramache, Experimental analysis on thermal performance of a
solar air collector with longitudinal fins in a region of Biskra, Algeria. Journal of Power Technologies. 93 (1):52–
58,2013.
[24] Gutti B, Kiman S and Mustafa B. G., Design and Construction of Forced/Natural Convection Solar Vegetable Dryer
with Heat Storage. Asian Research Publishing Network (ARPN). Journal of Engineering and Applied Sciences.7
(10):1213-1217,2012.
[25] Ayyappan S and Mayilsamy K., Solar tunnel drier with thermal storage for drying of Copra, Proceedings of
the 37th
National & 4th
International Conference on Fluid Mechanics and Fluid Power, IIT Madras, Chennai, India
,2010.
[26] Jain Dilip, Modeling the Performance of the Reversal Absorber with Packed Bed Thermal Storage Natural
Convection Solar Crop Dryer. Journal of Food Engineering.78:637-647,2006.
[27] Sing D, Bansal N.K., Analysis of a glass solar air heater. Energy Conversion and Management. 23(4):231-
6,1983.
[28] Tiwari, G.N., P.S. Bhatia, A.K. Singh and R.F., Sutar Design parameters of a shallow bed solar crop dryer with
reflector. Energy Conversion and Management. 35(6):542–635,1994.
[29] Chauhan, P.M., S.C. Choudhury and H.P. Garg, Comparative performance of coriander dryer coupled to solar air
heater and solar air-heater-cum-rock bed storage. Applied Thermal Eng.16:475–486,1996.
[30] Shanmugam, V. and E. Natarajan Experimental study of regenerative desiccant integrated solar dryer with and
without reflective mirror. Applied Thermal Engineering. 27(8-9): 1543–1551,2007.
[31] Mohanraj, M. and P.Chandrasekar, Drying of copra in forced convection solar drier. Biosystem Engineering.
99:604–607, 2008.
[32] Kamble, A. K., I. L. Pardeshi., P. L. Singh and G. S. Ade Drying of chilli using solar cabinet dryer coupled with
gravel bed heat storage system. Journal of Food Research and Technology. 1(2): 87-94,2013.
[33] Saxena, A., N. Agarwal and G. Srivastava, Design and performance of a solar air heater with long term heat storage.
International Journal of Heat and Mass Transfer.60:8–16,2013.
[34] Farid, M.M. and R.M. Husian, An electrical storage heater using the phase change method of heat storage. Energy
Conversion and Management 30(3): 219–230,1990.
[35] Fatah,HES, Thermal performance of a simple design solar air heater with built-in thermal energy storage system.
Energy Conversion and Management.36:989–999,1994.
[36] Fath,H.E., Thermal performance of simple design solar air heater with built- in thermal energy storage system.
Energy Conversion and Management. 36:989–97,1995.
[37] Enibe,S.O., Performance of a natural circulation solar air heating system with phase change material energy storage.
Renewable Energy. 27:69–86,2002.
[38] Takakura T, Nishina H., A solar greenhouse with phase change energy storage and a microcomputer control system.
Acta Hortic;115:583–90 (Energy in Protected Cultivation),1981.
[39] Benli,H. and A.Durmus, Performance analysis of a latent heat storage system with phase change material for new
designed solar collectors in greenhouse heating. Solar Energy. 83:2109–2119,2009.