Post on 31-Dec-2015
description
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Physics I95.141
LECTURE 1711/8/10
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Outline/Administrative Notes
• Outline– Ballistic Pendulums– 2D, 3D Collisions– Center of Mass and
translational motion
• Notes– HW Review Session
on 11/17 shifted to 11/18.
– Last day to withdraw with a “W” is 11/12 (Friday)
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Ballistic Pendulum
• A device used to measure the speed of a projectile.
vo v1
hmM M+m
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Ballistic Pendulum
vo v1
mM M+m
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Ballistic Pendulum
v1
hM+m
M+m
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Exam Prep Problem• You construct a ballistic “pendulum” out of a rubber block (M=5kg)
attached to a horizontal spring (k=300N/m). You wish to determine the muzzle velocity of a gun shooting a mass (m=30g). After the bullet is shot into the block, the spring is observed to have a maximum compression of 12cm. Assume the spring slides on a frictionless surface.
• A) (10pts) What is the velocity of the block + bullet immediately after the bullet is embedded in the block?
• B) (10pts) What is the velocity of the bullet right before it collides with the block?
• C) (5pts) If you shoot a 15g mass with the same gun (same velocity), how far do you expect the spring to compress?
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Exam Prep Problem
• k=300N/m, m=30g, M=5kg, Δxmax=12cm
• A) (10pts) What is the velocity of the block + bullet immediately after the bullet is embedded in the block?
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Exam Prep Problem
• k=300N/m, m=30g, M=5kg, Δxmax=12cm
• B) (10pts) What is the velocity of the bullet right before it collides with the block?
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Exam Prep Problem
• k=300N/m, m=30g, M=5kg, Δxmax=12cm
• C) (5pts) If you shoot a 15g mass with the same gun (same velocity), how far do you expect the spring to compress?
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Collisions• In the previous lecture we discussed collisions in 1D, and the
role of Energy in collisions.– Momentum always conserved!
– If Kinetic Energy is conserved in a collision, then we call this an elastic collision, and we can write:
– Which simplifies to:
– If Kinetic Energy is not conserved, the collision is referred to as an inelastic collision.
– If the two objects travel together after a collision, this is known as a perfectly inelastic collision.
systemsystem pp
BBAABBAA vmvmvmvm 2222
2
1
2
1
2
1
2
1BBABBA vmvmvmvm
AA
ABBA vvvv
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Collision Review• Imagine I shoot a 10g projectile at 450m/s towards a
10kg target at rest. – If the target is stainless steel, and the collision is elastic, what
are the final speeds of the projectile and target?
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Collision Review• Imagine I shoot a 10g projectile at 450m/s towards a
10kg target at rest. – If the target is wood, and projectile embeds itself in the target,
what are the final speeds of the projectile and target?
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Additional Dimensions
• Up until this point, we have only considered collisions in one dimension.
• In the real world, objects tend to exist (and move) in more than one dimension!
• Conservation of momentum holds for collisions in 1, 2 and 3 dimensions!
Department of Physics and Applied Physics95.141, F2010, Lecture 17
2D Momentum Conservation
BA ,
• Imagine a projectile (mA) incident, along the x-axis, upon a target (mB) at rest. After the collision, the two objects go off at different angles
• Momentum is a vector, in order for momentum to be conserved, all components (x,y,z) must be conserved.
Department of Physics and Applied Physics95.141, F2010, Lecture 17
2D Momentum Conservation
• Imagine a projectile (mA) incident, along the x-axis, upon a target (mB) at rest. After the collision, the two objects go off at different angles BA ,
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Conservation of Momentum (2D)
• Solving for conservation of momentum gives us 2 equations (one for x-momentum, one for y-momentum).
• We can solve these if we have two unknowns• If the collision is elastic, then we can add a third
equation (conservation of kinetic energy), and solve for 3 unknowns.
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Example problem• A cue ball travelling at 4m/s strikes a billiard ball at rest (of equal
mass). After the collision the cue ball travels forward at an angle of +45º, and the billiard ball forward at -45º. What are the final speeds of the two balls?
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Example Problem II• Now imagine a collision between two masses (mA=1kg and mB=2kg)
travelling at vA=2m/s and vB= -2m/s along the x-axis. If mA bounces back at an angle of -30º, what are the final velocities of each ball?
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Example Problem II• Now imagine a collision between two masses (mA=1kg and mB=2kg)
travelling at vA=2m/s and vB= -2m/s on the x-axis. If mA bounces back at an angle of -30º, what are the final velocities of each ball, assuming the collision is elastic?
sm
Av 26.3 sm
Bv 82.0 8.63B
BBBAAABBAA vmvmvmvm coscosBBBAAA vmvm sinsin0
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Simplification of Elastic Collisions
• In 1D, we showed that the conservation of Kinetic Energy can be written as:
• This does not hold for more than one dimension!!
ABBA vvvv
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Problem Solving: Collisions
1. Choose your system. If complicated (ballistic pendulum, for example), divide into parts
2. Consider external forces. Choose a time interval where they are minimal!
3. Draw a diagram of pre- and post- collision situations
4. Choose a coordinate system
5. Apply momentum conservation (divide into component form).
6. Consider energy. If elastic, write conservation of energy equations.
7. Solve for unknowns.
8. Check solutions.
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Center of Mass• Conservation of momentum is powerful for collisions and
analyzing translational motion of an object.
• Up until this point in the course, we have chosen objects which can be approximated as a point particle of a certain mass undergoing translational motion.
• But we know that real objects don’t just move translationally, they can rotate or vibrate (general motion) not all points on the object follow the same path.
• Point masses don’t rotate or vibrate!
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Center of Mass
• We need to find an addition way to describe motion of non-point mass objects.
• It turns out that on every object, there is one point which moves in the same path a particle would move if subjected to the same net Force.
• This point is known as the center of mass (CM).• The net motion of an object can then be
described by the translational motion of the CM, plus the rotational, vibrational, and other types of motion around the CM.
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Example
F
F
F
F
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Center of Mass
• If you apply a force to an non-point object, its center of mass will move as if the Force was applied to a point mass at the center of mass!!
• This doesn’t tell us about the vibrational or rotation motion of the rest of the object.
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Center of Mass (2 particles, 1D)
• How do we find the center of mass?• First consider a system made up of two point masses,
both on the x-axis.
x-axisx=0 xA
mAxB
xB
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Center of Mass (n particles, 1D)
• If, instead of two, we have n particles on the x-axis, then we can apply a similar formula to find the xCM.
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Center of Mass (2D, 2 particles)
• For two particles lying in the x-y plane, we can find the center of mass (now a point in the xy plane) by individually solving for the xCM and yCM.
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Center of Mass (3D, n particles)• We can extend the previous CM calculations to n-
particles lying anywhere in 3 dimensions.
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Example• Suppose we have 3 point masses (mA=1kg, mB=3kg and
mC=2kg), at three different points: A=(0,0,0), B=(2,4,-6) and C=(3,-3,6).
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Solid Objects• We can easily find the CM for a collection of point
masses, but most everyday items aren’t made up of 2 or 3 point masses. What about solid objects?
• Imagine a solid object made out of an infinite number of point masses. The easiest trick we can use is that of symmetry!
Department of Physics and Applied Physics95.141, F2010, Lecture 17
CM and Translational Motion
• The translational motion of the CM of an object is directly related to the net Force acting on the object.
• The sum of all the Forces acting on the system is equal to the total mass of the system times the acceleration of its center of mass.
• The center of mass of a system of particles (or objects) with total mass M moves like a single particle of mass M acted upon by the same net external force.
extCM FaM
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Example• A 60kg person stands on the right most edge of a uniform board of
mass 30kg and length 6m, lying on a frictionless surface. She then walks to the other end of the board. How far does the board move?
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Solid Objects (General)• If symmetry doesn’t work, we can solve for CM
mathematically. – Divide mass into smaller sections dm.
rdm
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Solid Objects (General)
• If symmetry doesn’t work, we can solve for CM mathematically. – Divide mass into smaller sections dm.
xdmM
xCM1
ydmM
yCM1
zdmM
zCM1
i
iiCM dmxM
x1
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Example: Rod of varying density
• Imagine we have a circular rod (r=0.1m) with a mass density given by ρ=2x kg/m3.
L=2mx
Department of Physics and Applied Physics95.141, F2010, Lecture 17
Example: Rod of varying density
• Imagine we have a circular rod (r=0.1m) with a mass density given by ρ=2x kg/m3.
L=2mx