Post on 08-Aug-2018
8/22/2019 Oce Connectivity Manual_v1
1/274
Oc TDS-TCS
Connectivity Manual
8/22/2019 Oce Connectivity Manual_v1
2/274
Copyright
Oc-Technologies B.V. Venlo, The Netherlands 2002
All rights reserved. No part of this work may be reproduced, copied, adapted,
or transmitted in any form or by any means without written permission fromOc.
Oc-Technologies B.V. makes no representation or warranties with respect to
the contents hereof and specifically disclaims any implied warranties of
merchantability or fitness for any particular purpose.
Further, Oc-Technologies B.V. reserves the right to revise this publication and
to make changes from time to time in the content hereof without obligation to
notify any person of such revision or changes.
Edition 2.0 October 2002
Oc-Technologies B.V.
GB
This manual contains a description of how the Oc TDS-TCS is connected to
the network using variuous connection types and how to connect workstationto the Oc TDS-TCS Digital Multifuctional System.
8/22/2019 Oce Connectivity Manual_v1
3/274
Contents 3
Contents
Chapter 1
Introduction
Supported transport and printing protocols 8
Physical connections 9
Preferred printing solutions 10
Peer-to-Peer configuration 10
Client/Server configuration 11
Oc Recommended Connections and Setup versus Protocols 12
Chapter 2Novell Environment
Introduction 14
Illustration conventions 14
References 14
PSERVER Setup 15
Queue Based Printing 15
Controller Setup 16
Novell Server Setup 22
Client Workstation Setup 43
Client Workstation Setup (WRD2 driver) 44
Client Workstation Setup (PS3 driver) 52
Client Workstation setup (Autocad 14 ADI driver) 68
Client Workstation setup (Autocad 2000/HDI1 & Autocad 2000i/HDI2) 71
Client Workstation setup (WPD driver) 75
Queue Based Printing Troubleshooting 86
NDPS Setup 89
Novell Distributed Print Services (NDPS) 89
Controller Setup 90
Novell Server Setup 91Client WorkStation Setup 109
NDPS Troubleshooting 115
8/22/2019 Oce Connectivity Manual_v1
4/274
4 Oc TDS Connectivity Manual
Chapter 3
TCP/IP protocol
Introduction 118
Illustration conventions 118
Prerequisites 119
Microsoft TCP/IP Printing Service (for all Operating Systems) 119LPR Protocol (for Windows 2000/XP only) 120
General TDS-TCS setup 122
Server setup 127
Print server configuration (Windows Raster Driver 2) 128
Print server configuration (Windows Printer Driver) 133
Print server configuration (PostScript 3 driver) 139
Client setup 144
Peer to Peer configuration 145
Print via FTP 145Print via Windows Raster Driver 2 147
Print via Windows Printer Driver 150
Print via PostScript3 driver 154
Print via Autocad ADI driver 160
Print via Autocad HDI driver 160
Client/Server configuration 161
Client/Server (Windows Raster Driver 2) 161
Client/Server (Windows Printer Driver) 165
Client/Server (PostScript 3 driver) 169
Client/Server (Autocad ADI) 173
Client/Server (Autocad HDI) 176
8/22/2019 Oce Connectivity Manual_v1
5/274
5
Chapter 4
SMB protocol
Introduction 182
Illustration conventions 182
Prerequisites 183
Windows 9x/Me 183Windows NT/2000/XP 185
General TDS/TCS setup 186
Server setup 189
Print Server configuration (Windows Raster Driver 2) 190
Print Server configuration (Windows Printer Driver) 201
Print Server configuration (PostScript 3) 205
Client Setup 217
Direct connection (Windows Raster Driver 2) 217
Direct connection (Windows Printer Driver) 224Direct connection (Postscript 3 Driver) 227
Direct connection (Autocad ADI) 232
Direct connection (Autocad HDI) 235
Print Server Configuration (Windows Raster Driver 2) 239
Print Server Configuration (Windows Printer Driver) 248
Print Server Configuration (PostScript 3) 251
Print Server Configuration (Autocad ADI) 257
Print Server Configuration (Autocad HDI) 261
Appendix A
General 266
Switch the Oc Setting Editor in SA Mode 267
Set up the SMB parameters on the Oc TDS controller 269
Set up the TCP/IP parameters on the Oc TDSx00/TCS400 Controllers 270
Set up the parameters on the Oc TDSx00/TCS400 Controllers/Novell Servers for
Novell Queue Based printing services 271
Reboot the controller 272
Scan To File: How to retrieve scanned files? 273
8/22/2019 Oce Connectivity Manual_v1
6/274
6 Oc TDS Connectivity Manual
8/22/2019 Oce Connectivity Manual_v1
7/274
7
Oc TDS-TCS
Connectivity Manual
Chapter 1Introduction
This chapter gives an introduction to the protocols,
connections and printing solutions for the
TDSx00/TCS400.
8/22/2019 Oce Connectivity Manual_v1
8/274
8 Oc TDS-TCS Connectivity Manual
Supported transport and printing protocols
Note: To simplify installation, the Oc TDSXXX has been designed to be plug
and play.
The Oc TDSx00/TCS400 supports the following transport protocols:
s TCP/IP
s IPX/SPX
s NetBeui
The Oc TDSx00/TCS400 supports the following printing protocols:
s LPD, FTP
s Pserver (Bindery and NDS)
s SMB printing (also known as LAN Manager or Windows networking) on top
of Netbios over NetBeui, TCP/IP or IPX/SPX
8/22/2019 Oce Connectivity Manual_v1
9/274
Introduction 9
Physical connections
With the Oc TDSx00/TCS400 the following networking boards are available:
s Standard motherboard: Ethernet (UTP) 10/100 Mbit with RJ45connector
s Optional Ethernet board with 3 connectors:
- RJ45 (10 Mbit only)
- AUI
- BNC
s Optional Token-Ring board with 2 connectors:
- RJ45
- 9 pin DB9
8/22/2019 Oce Connectivity Manual_v1
10/274
10 Oc TDS-TCS Connectivity Manual
Preferred printing solutions
Depending on your network architecture, multiple printing solutions are
available for each supported operating system. Basically there are two mainconfiguration types:
Where:
s TDS/TCS is the Oc TDSx00/TCS400 Controller
s PS is the Print Server workstation (as defined by the customer)
s WS is any Client workstation
s P2P means Peer to Peer connection
s C/S means Client/Server connection
Peer-to-Peer configuration
In this Configuration, the Client WorkStation is directly connected to the
controller.
The main advantage of the Peer to Peer is in the throughput: only one data
transfer from the Client workstation to the controller.
The main drawback is the lack of centralized resource administration and
setup: each Client workstation has to be setup individually. Also the maximum
number of simultaneous connection is limited to 10.
SMB (NetBeui) and TCP/IP Protocols allow this type of configuration.
8/22/2019 Oce Connectivity Manual_v1
11/274
Introduction 11
Client/Server configuration
In this Configuration, the printing resources administration are centralized and
controlled by a System Administrator. The Client workstation is no more
directly connected to the controller, but to a Print Server workstation.
The main advantages are the central administration of the printing resources,
the number of simultaneous connection and the possibility of application and
driver updates.
The main drawback is in the network traffic: printing data are sent twice on the
LAN.
The IPX/SPX Protocol can only work with this configuration.
The SMB (NetBeui) and TCP/IP Protocols also allow this type ofconfiguration.
8/22/2019 Oce Connectivity Manual_v1
12/274
12 Oc TDS-TCS Connectivity Manual
Oc Recommended Connections andSetup versus Protocols
Regarding connections, the 3 different protocols (Novell, TCP/IP, SMB) are
detailed in the three following chapters.
Our recommendation for having the easiest Client WorkStation Setup and a
better Printer Remote Administration is to use a Client-Server architecture
whatever the protocol is.
For the Print server, prefer a workstation running a recent operating system
(Win XP or 2000 rather than Win NT4); it offers a wider range of sharing
possibilities.
On this print server, install the Oc driver you need (Windows Raster Driver 2,
Windows Printer Driver, PostScript 3) and share it.
We mainly recommend that the Oc TSDx00/TCS400 controller be connected
via TCP/IP LPR Protocol to this Print Server.
All Client workstations (Windows 95/98, Windows NT 4.0, Windows 2000 or
Windows XP) have access to this shared printer by using the SMB Point and
Print facility.
8/22/2019 Oce Connectivity Manual_v1
13/274
13
Oc TDS/TCS
Connectivity Manual
Chapter 2Novell Environment
This chapter describes how to setup the Oc controller to
make it work in a Novell environment.
8/22/2019 Oce Connectivity Manual_v1
14/274
14 Oc TDS/TCS Connectivity Manual
Introduction
There are 2 methods to print on TDSx00/TCS400 in a Novell environment:
s using Novell Queue Based Network Printing (traditional or legacy
implementation of print services provided through NetWare.)
Note: This method is available on Netware 3.X, 4.X, 5.X.
s using Novell Distributed Print Services (NDPS), the default print system
in NetWare 5.
This chapter describes how to setup the customer environment to print on an
Oc TDSx00/TCS400 with one of these methods.
Illustration conventions
Here are the conventions used in the illustrations of this manual:
s [Oce_Printer]: WorkGroup / Domain Name (default value: Oce_Printer)
s [Oce_System]: Machine Name (default value: OceTDSx00)
s [Printer] & [PrinterPS]: Printer Names (default values: OceTDSx00
OceTDSx00PS)s The SMB standard UNC used are the following:
\\[Oce_system]\[Printer] which stands for \\OceTDSx00\OceTDSx00
\\[Oce_system]\[PrinterPS] which stands for \\OceTDSx00\OceTDSx00PS
s The Oc Novell Print Server Name used is [OcePserver]
s The NDS Domain used is [NDSDomain]
ReferencesFor more details, please refer to the Novell administration guides:
s For Queue Based Printing:
http://www.novell.com/documentation/lg/nw51/pdfdoc/10412291.pdf
s For NDPS:
http://www.novell.com/documentation/lg/nw51/pdfdoc/10412271.pdf
8/22/2019 Oce Connectivity Manual_v1
15/274
Novell Environment 15
PSERVER Setup
Queue Based PrintingA Print Server running on the TDSx00/TCS400 controller connects to a Novell
Server. A client sends jobs to a queue on the Novell Server. The Oc
TDSx00/TCS400 controller Print Server which regularly requests jobs to the
Novell Server (polling mode) retrieves those jobs and prints them.
[1] Overview of Queue based Printing
Configuration
You need to configure not only the Client Workstation and the Oc
TDSx00/TCS400 but also the Novell Server in order to establish the
connection between the Oc Print Server (on Oc TDSx00/TCS400 printer
controller) and the Novell server.
Note: The Peer-to-Peer connection does not exist on IPX/SPX protocol.
wSet up the environment
1 Setup the Oc TDSx00/TCS400 Controller, and DO NOT reboot it.
2 Setup the end user environment (Novell Server).
3 Reboot the Oc TDSx00/TCS400 Controller.
4 Check Oc TDSx00/TCS400 Print Server status on Novell Server.
5 Setup the client workstation (driver installation).
6 Print a test page to check the setup is correct.
Note: These steps are described in the following sections.
8/22/2019 Oce Connectivity Manual_v1
16/274
16 Oc TDS/TCS Connectivity Manual
Controller Setup
In order to run into an IPX/SPX Environment, some parameters have to be
setup:
s enable Novell protocols setup Pserver Name & Password
s setup Bindery Access Mode or NDS Access Mode
s setup the preferred file servers
w Enable the IPX/SPX Novell protocol.
Note: You MUST be logged as a System Administrator.
1 Switch the Oc Setting Editor in SA Mode (see Switch the Oc Setting
Editor in SA Mode on page 267).2 Expand the Connectivity Folder.
3 Expand the Novell folder.
4 Select Enable Novell document.
5 Select Enable on the right window (Enable Novell).
6 ClickApply.
7 Setup the other parameters.
8 Once all setups are done, configure Novell server BEFORE rebooting the
controller (see Reboot the controller on page 272).
8/22/2019 Oce Connectivity Manual_v1
17/274
Novell Environment 17
w Setup the Print Server Name (PSERVER)
Note: You MUST be logged as a System Administrator.
1 Switch the Oc Setting Editor in SA Mode (see Switch the Oc Setting
Editor in SA Mode on page 267).
2 Expand the Connectivity Folder.3 Expand the Novell folder.
4 Select Pserver name document.
5 Type in the Print Server name (for instance, PSTDSX00) into the input field in
the right window (Pserver name):
6 ClickApply.
7 Setup the other parameters.
8 Once all setups are done, configure Novell server BEFORE rebooting the
controller (see Reboot the controller on page 272).
8/22/2019 Oce Connectivity Manual_v1
18/274
18 Oc TDS/TCS Connectivity Manual
w Setup the controller to work in Bindery Access Mode
Note: You MUST be logged as a System Administrator.
1 Switch the Oc Setting Editor in SA Mode (see Switch the Oc Setting
Editor in SA Mode on page 267).
2 Expand the Connectivity Folder.
3 Expand the Novell folder.
4 Select Access Mode document.
5 Select Bindery on the right window (Access Mode):
6 ClickApply.
7 Setup the other parameters.
8 Once all setups are done, configure Novell server BEFORE rebooting the
controller (see Reboot the controller on page 272).
8/22/2019 Oce Connectivity Manual_v1
19/274
Novell Environment 19
w Setup the controller to work in NDS Access Mode
Note: You MUST be logged as a System Administrator.
1 Switch the Oc Setting Editor in SA Mode (see Switch the Oc Setting
Editor in SA Mode on page 267).
2 Expand the Connectivity Folder.
3 Expand the Novell folder.
4 Select Access Mode document.
5 Select NDS on the right window (Access Mode):
6 In the Novell folder, select NDS Context document.
7 Type in the context where the TDSx00/TCS400 will be installed (Ex:
SNSESC) into the input field in the right window (NDS Context).
8/22/2019 Oce Connectivity Manual_v1
20/274
20 Oc TDS/TCS Connectivity Manual
Here are different NDS context examples you can set in this field:
NDS context: SNSESC
NDS context: SNS.OCE
NDS context: OU=SNS.O=OCE
NDS context: OU=SNS.O=OCE.C=FR
(see Queue Based Printing Troubleshooting on page 86).
8 ClickApply.
9Setup the other parameters.
10 Once all setups are done, configure Novell server BEFORE rebooting the
controller (seeReboot the controller on page 272).
8/22/2019 Oce Connectivity Manual_v1
21/274
Novell Environment 21
w Setup the Novell File servers which the printer connects to.
Note: You MUST be logged as a System Administrator.
1 Switch the Oc Setting Editor in SA Mode (seeSwitch the Oc Setting
Editor in SA Mode on page 267).
2 Expand the Connectivity Folder.
3 Expand the Novell folder.
4 Select File server names document.
5 Type in the names of the Novell File Server(s) to which this printer will be
connected using the ; as separator whether more than one Server is specified
(Ex: SNSNW5 or SPSNW4;SNSNW5) into the input field in the right
window (File server names).
6 ClickApply.
7 Setup the other parameters.
8 Once all setups are done, configure Novell server BEFORE rebooting the
controller (seeReboot the controller on page 272).
8/22/2019 Oce Connectivity Manual_v1
22/274
22 Oc TDS/TCS Connectivity Manual
Novell Server Setup
This section is aimed at the Local Network Administrator. It describes:
s how to setup the End User Site Environment for sharing the Oc
TDSx00/TCS400 printer resource on his LAN by using the IPX/SPXprotocol.
s how to setup, in a Client/Server Environment, a Novell File Server (by using
the Print Server embedded in the Oc TDSx00/TCS400 Printer Controller).
To allow a Novell Client to access the Oc TDSx00/TCS400 Print Resource,
you have to setup the Novell File Server in order to establish the connection
between this Novell File Server and the Oc Print Server you previously
setup on the Oc TDSx00/TCS400 Printer Controller.
The following procedures describe how to setup on:
s Novell 3.x File Server / Bindery Mode
s Novell 4.x File Server / NDS Mode
s Novell 5.x File Server / NDS Mode
Note: Only the Bindery Mode is available on Novell 3.x File Servers.
Note:The Bindery mode is also available on Novell 4.x and Novell 5.x, but werecommend to use NDS mode on such File Servers.
Note: You MUST be logged in as Novell System Administrator on any
Windows WorkStation running Novell Client 32 over any MS Windows
Operating System.
8/22/2019 Oce Connectivity Manual_v1
23/274
Novell Environment 23
Setup on Novell 3.x File Server
Note the following parameters used in our example, some of them must be set
up on the Oc TDSx00/TCS400 Controller:
s Novell File server: SNSNW3 (To be setup on the controller)
s Oc TDSx00 Print Server Name: OCTDSx00(To be setup on the controller & the Novell File Server)
s Access Mode: Bindery (To be setup on the controller)
s Oc TDSx00 Printer Name: TDSx00 (To be setup on the Novell File Server)
s Oc TDSx00 Printer Queue Name: QTDSx00 (To be setup on the Novell File
Server)
w Launch the Administration task
1 Logon as System Administrator, using the proper Context, Tree and Server.
2 Launch the Novell Administration Task (Pconsole.exe) located into the
Public\ directory, generally mapped on Z:\.
3 Open My Computer, locate and expand the [Server]\Public Directory:
4 Double-clickPconsole.exe to launch the PCONSOLE Administration
Task.
8/22/2019 Oce Connectivity Manual_v1
24/274
24 Oc TDS/TCS Connectivity Manual
w Create the Printer Queue.
1 Select Print Queue Information:
2 Press the INSERT key to create the New Printer Queue:
3 Enter the new Print Queue Name (ex: QTDSx00) and press RETURN:
8/22/2019 Oce Connectivity Manual_v1
25/274
Novell Environment 25
w Create the Print Server on the Novell File Server
1 Press ESC to display the PCONSOLE Main Menu.
2 Select Print Server Information and press the RETURN key.
3 Press the INSERT key to create the New Print Server:
4 Enter the New Print Server Name (ex: OCTDSx00) and press RETURN:
8/22/2019 Oce Connectivity Manual_v1
26/274
26 Oc TDS/TCS Connectivity Manual
w Set up the printers handled by this new Print Server
Note: For our purpose, there is only one printer to be defined and its name
can be any name. We recommend to use a meaningful one (ex: TDSx00).
1 Select Printer Configuration and press the RETURN key:
2 Select the first Not Installed Printer and press the RETURN key:
The Printer x Configuration window is then displayed:
3 Setup the Printer x by entering the new Printer Name (for instance: TDSx00).
8/22/2019 Oce Connectivity Manual_v1
27/274
Novell Environment 27
4 Select the Remote Other/Unknown type:
5 Press the ESC key to validate and save your settings:
8/22/2019 Oce Connectivity Manual_v1
28/274
28 Oc TDS/TCS Connectivity Manual
w Set the Printer Queue(s) which are serviced by this new Print Server.
1 Select Queues Serviced by Printer and press RETURN:
The Printers serviced by the Print Server are displayed:
2 Select the appropriate Printer (ex: TDSx00) and press the RETURN key:
8/22/2019 Oce Connectivity Manual_v1
29/274
Novell Environment 29
3 Press INSERT and choose the proper Queue in the List (e.g: QTDSx00):
4 Press the RETURN key and setup the proper priority (keep the 1 value):
5 Press RETURN.
Note: The Printer (TDSx00) is now serviced by the Queue (QTDSx00), by
the Print Server (OCTDSx00) defined on the Novell 3.x File Server
(SNSNW3) :
6 Press ESC to display the Quit window.
7 Select Yes and press the RETURN key.
8/22/2019 Oce Connectivity Manual_v1
30/274
30 Oc TDS/TCS Connectivity Manual
w Check if the Oc TDSx00 Printer Resource is available for the Users
1 Reboot the TDSx00/TCS400 Printer Controller and start it.
2 Launch the PCONSOLE Administration Utility on a Client WorkStation.
3 Select Print Server Information and press the RETURN key:
4 Select Print Server Status/Control and press the RETURN key:
5 Select Printer Status and press the RETURN key:
8/22/2019 Oce Connectivity Manual_v1
31/274
Novell Environment 31
6 Select the appropriate Active Printer (eg:TDSx00) and press RETURN:
The Status MUST be Waiting for Jobs.:
7 Press ESC and clickYES in the Quit window to quit the PCONSOLEAdministration Tool.
8/22/2019 Oce Connectivity Manual_v1
32/274
32 Oc TDS/TCS Connectivity Manual
Novell 4.x File Server Setup
Note: It is recommended to use the NDS mode when using Novell 4.x.
Note the following parameters used in our example, some of them must be set
up on the Oc TDSx00/TCS400 Controller:
s Novell Context: SPSESC (to be set on the controller)
s Novell Tree: SPSESC
s Novell File server: SPSNW4 (to be set on the controller)
s OcTDSx00 Print Server Name: OCTDSx00
(to be set on the controller and the Novell File Server)
s OcTDSx00 Printer Name: TDSx00
(to be set on the Novell File Server)
s OcTDSx00 Printer Queue Name: QTDSx00
(to be set on the Novell File Server)
w Launch the Administration task
1 Logon as System Administrator, using the proper Context, Tree and Server.
2 Open My Computer, locate and expand the [Server]\Public Directory:
3 Double-click Nwadmin.exe to launch the Administration Task.
8/22/2019 Oce Connectivity Manual_v1
33/274
Novell Environment 33
w Setup the print resource on the Novell File Server
1 Browse and open the proper Context (SPSESC).
2 Select the proper Tree (SPSESC).
3 From the Tools menu, select Print Service Quick Setup:
The Print Service Quick Setup window is displayed.
8/22/2019 Oce Connectivity Manual_v1
34/274
34 Oc TDS/TCS Connectivity Manual
4 Fill in the following fields:
s Print Server Name (for instance, OCTDSx00)
s Printer Name (for instance, TDSx00)
s Printer Type (select Other/Unknown)
s Printer Banner Type (select PostScript)
s Print Queue Name (for instance, QTDSx00)
5 ClickCreate. In the Administration Main Windows, 3 new objects are
created: a Print Server named OCTDSx00, a Print Queue named QTDSx00
and a Printer named TDSx00:
6 Reboot the Oce TDSx00/TCS400 Printer Controller and start it.
8/22/2019 Oce Connectivity Manual_v1
35/274
Novell Environment 35
w Check if the setup (Oc TDSx00/TCS400 controller and Novell File Server) is
correct
1 Double-clickPrint Server Object (OCTDSx00). A Print Server window is
opened where you may see:
s a Network Address which MUST exist (IPX:)
s Status Running
Note: The Status may sometimes not be Running but Down instead. This
does not necessarily mean the Print Server is not working. This Novell
status is not reliable and cannot be used to check whether Print Server is
correctly running.
2 You can check if the Print Server embedded in Oc TDSx00/TCS400 is
correctly connected to the Novell Server by checking the Novell Server itself.
There is an active connection on print server (PSTDSx00) which must appear
in Netware 4 Console Monitor / Connection with the status: NORMAL.
8/22/2019 Oce Connectivity Manual_v1
36/274
36 Oc TDS/TCS Connectivity Manual
3 To check if Oc TDSx00 Printer Resource is available for users, browse the
Network and select the proper Context and Tree (SPSESC/SPSESC).
The new shared Printer TDSx00 is displayed:
4 Right-click on the printer and select Properties:
8/22/2019 Oce Connectivity Manual_v1
37/274
Novell Environment 37
Novell 5.x File Server Setup
Note: It is recommended to use the NDS mode when using Novell 5.x.
Three printing objects must be created on the Novell Server:
s A Print Server object (the name must be identical to the Pserver nameparameter setup in the Oc TDSx00/TCS400 Controller by means of the
Settings Editor, refer to the Controller setup section)
s A Queue object
s A Printer object
These 3 objects must be linked together and you have to check the Oc
TDSx00/TCS400 Print Server is connected to the Novell server.
Note the following parameters used in our example, some of them must be setup on the Oc TDSx00/TCS400 Controller:
s Novell Context: SNSESC (to be set on the controller)
s Novell Tree: SNSESC
s Novell File server: SNSNW5 (to be setup on the controller)
s Oc TDSx00 Print Server Name: PSTDSx00
(to be set on the controller and on the Novell File Server)
s Oc TDSx00 Printer Name: TDSx00
(to be set on the Novell File Server)s Oc TDSx00 Printer Queue Name: QTDSX00
(to be set on the Novell File Server)
8/22/2019 Oce Connectivity Manual_v1
38/274
38 Oc TDS/TCS Connectivity Manual
w Launch the Administration Task
1 Logon as System Administrator, using the proper Context, Tree and Server.
2 Open My Computer, locate and expand the [Server]\Public Directory:
3 Open the Win32 Sub-Directory and double-click on Nwadmn32.exe to
launch the Administration Task.
8/22/2019 Oce Connectivity Manual_v1
39/274
Novell Environment 39
w Setup the print resource on the Novell File server
1 Browse and open the proper Context (for instance, SNSESC).
Caution: This context must correspond to the NDS context entered on the
Oc TDSx00/TCS400 controller by means of the Settings Editor.
2 Select the proper Tree (for instance, SNSESC).3 From the Tools menu, select Print Service Quick Setup (Non-NDPS):
4 The Print Service Quick Setup (Non-NDPS) window is displayed.
Fill in the following fields:
s Print Server Name (for instance, PSTDSX00)
s Printer Name (for instance, TDSX00)
s Printer Type (select Other/Unknown- used for Network)
s Printer Banner Type (select PostScript)
s Print Queue Name (for instance, QTDSX00)
8/22/2019 Oce Connectivity Manual_v1
40/274
40 Oc TDS/TCS Connectivity Manual
5 ClickCreate. In the Administration main window, 3 new objects are created:
s a Print Server named PSTDSX00
s a Print Queue named QTDSX00
s a Printer named TDSX00
6 Reboot the Oc TDSx00/TCS400 Printer Controller.
8/22/2019 Oce Connectivity Manual_v1
41/274
Novell Environment 41
w Check the setup is correct.
1 Double-click on the Print Server Object (PSTDSX00) to check the 3
objects (Print Server, Print Queue and Printer).
2 Click the Print Layout (Non NDPS) tab:
Note: On this illustration, the exclamation mark does not necessarily mean
the Print Server is not working. This Novell status is not reliable and
cannot be used to check whether Print Server is correctly running.
3 Check if the Print Server embedded in Oc TDSx00/TCS400 is correctly
connected to the Novell Server by checking on the Novell Server itself. There
is an active connection on print server (PSTDSX00) which must appear in
Netware 5 Console Monitor / Connection with the status: NORMAL:
8/22/2019 Oce Connectivity Manual_v1
42/274
42 Oc TDS/TCS Connectivity Manual
4 To check if the Oc TDSx00/TCS400 Printer Resource is available for the
Users, browse the network using Network Neighborhood and selecting the
proper Context and Tree (SNSESC/SNSESC). The new shared Printer
TDSx00 is displayed:
5 Right-click on the printer and select Properties:
8/22/2019 Oce Connectivity Manual_v1
43/274
Novell Environment 43
Client Workstation Setup
This section is aimed at the local network administrator and/or end user. It
describes how to setup the client workstations, by using a Client/Server
connection, in order to use the Oc TDSx00/TCS400 Printer resource on a
LAN via the IPX/SPX protocol.
Note: The Peer-to-peer connection is not possible when using the IPX/SPX
protocol.
Note: The Client/Server connection allows a client workstation to be connected
to the OcTDSx00/TCS400 Printer via a Novell Print Server, defined on the
Novell File Server as Printer Queues.
8/22/2019 Oce Connectivity Manual_v1
44/274
44 Oc TDS/TCS Connectivity Manual
Client Workstation Setup (WRD2 driver)
w Setup Windows 9x/Me Client WorkStation for a TDSx00
1 From the Windows START menu, select SETTINGS / PRINTERS.
The Printers window is displayed:
2 Double-click the Add printer icon:
3 ClickNEXT.
8/22/2019 Oce Connectivity Manual_v1
45/274
Novell Environment 45
4 Select NETWORK PRINTER and clickNEXT:
5 ClickBROWSE:
6 Locate the TDSx00 on the network by selecting:
s the network (Netware network / Netware servers)
s the file server (for instance, SNSNW5)
s the printer queue (for instance, QTDSx00)
The following window is displayed:
8/22/2019 Oce Connectivity Manual_v1
46/274
46 Oc TDS/TCS Connectivity Manual
7 ClickOK. The Add printer wizard window is displayed, with the selected
printer in the Network path or queue name field (e.g: \\SNSNW5\QTDSx00).
8 ClickNEXT. The Building driver information database window is
displayed followed by the Add printer wizard window including a list of
manufacturers and printers:
9 ClickHAVE DISK. The Install from disk window is displayed:
10 ClickBROWSE. The Open window is displayed.
8/22/2019 Oce Connectivity Manual_v1
47/274
Novell Environment 47
11 Select the directory where the Oce WRD2 distribution is located (for instance:
Cd_Pack\products\wrd2\TDSx00\win9x\):
12 Select the TDSx00.inf file.
13 ClickOK. The Install from disk window is again displayed, with the
selected path appearing on the copy manufacturer's file from line.
14 ClickOK. The Add printer wizard window is displayed, including a list of
Oce printers:
15 Select the OceTDSx00 Raster model.
8/22/2019 Oce Connectivity Manual_v1
48/274
48 Oc TDS/TCS Connectivity Manual
16 ClickNEXT. The Add printer wizard window is displayed, including the
default printer name:
17 Change the printer name if required.
18 Select if you want the TDSx00 to be used as default printer.
19ClickFINISH. Files are copied to the PC hard disk, then the SoftwareProduct license window is displayed:
20 ClickYES. The Printers window is displayed with OceTDSx00 Raster:
A window prompts you to restart the computer to complete the installation.
21 ClickYES.
8/22/2019 Oce Connectivity Manual_v1
49/274
Novell Environment 49
w Setup Windows NT/2000/XP Client WorkStation for a TDSx00
1 Open the Windows Explorer.
2 Browse to locate the directory where the Oce Windows WRD2 driver
distribution is located (for instance: Cd_Pack\products\TDSx00\wrd2\nt4) :
3 Double-click on setup.exe. The Oce TDSx00 Printer driver installer is
launched and the End User License Agreement window is displayed:
4 ClickAccept. The Printer installation window is displayed:
8/22/2019 Oce Connectivity Manual_v1
50/274
50 Oc TDS/TCS Connectivity Manual
5 ClickAdd Network Port:
6 Browse the network to locate the TDSx00 printer by selecting:
s the network (Netware network / Netware servers)
s the file server (for instance, SNSNW3)
s the printer queue (for instance, QTDSx00)
7 Select the TDSx00 printer queue and clickOK.
The Printer installation window is displayed, with the selected printer queue
appearing in the port line (for instance, \\SNSNW3\QTDSx00):
8/22/2019 Oce Connectivity Manual_v1
51/274
Novell Environment 51
8 ClickNEXT.
9 ClickNEXT.
10 ClickFINISH. Files are copied to the PC hard disk and the Installation
successful window is displayed:
11 ClickRestart Windows now to reboot the workstation.
12 After the workstation restarted, check in the Printers window (Start menu
\settings\printers) if the new TDSx00 printer is in the available printers list:
8/22/2019 Oce Connectivity Manual_v1
52/274
52 Oc TDS/TCS Connectivity Manual
Client Workstation Setup (PS3 driver)
w Setp Windows 9x/Me/NT workstation
1 Open the Windows Explorer.
2 Browse to locate the directory where the Oce Windows Postscript 3 driverdistribution is located (for instance: Cd_Pack\products\TDSx00\ps3\):
3 Double-clicksetup.exe. The Adobe Postscript Driver Installer is launched:
4 ClickNEXT. The End user license agreement window is displayed.
8/22/2019 Oce Connectivity Manual_v1
53/274
Novell Environment 53
5 ClickAccept. The Printer connection type window is displayed:
6 Select It is connected to your network (Network Printer) and clickNEXT.
The Network path window is displayed:
7 ClickBROWSE. The Browse for printer window is displayed:
8/22/2019 Oce Connectivity Manual_v1
54/274
54 Oc TDS/TCS Connectivity Manual
8 Locate the TDSx00PS printer on the network by selecting:
s the network (Netware network / Netware servers)
s the file server (for instance, SNSNW5)
s the printer queue (for instance, QTDSx00PS)
The following window is displayed:
9 ClickOK. The Network path window is displayed, with the selected printer
(for instance, \\SNSNW5\QTDSx00PS):
10 ClickNEXT. The Select printer model window is displayed:
11 Select the TDSx00PS printer.
8/22/2019 Oce Connectivity Manual_v1
55/274
Novell Environment 55
12 ClickNEXT. The Printer information window is displayed:
13 Choose if you want to use the TDSx00PS as default printer and if you want to
print a test page.
14ClickNEXT. The Setup information window is displayed:
15 ClickInstall. Files are copied to the PC hard disk, then the Printer
configuration window is displayed:
16 Select if you want to configure the printer now or later.
8/22/2019 Oce Connectivity Manual_v1
56/274
56 Oc TDS/TCS Connectivity Manual
17 ClickNEXT.
s If you choose to perform the printer configuration now, the Properties
window is displayed and the printer setup can be done.
s If you choose to perform the printer configuration later, the Setup complete
window is displayed:
18 ClickFINISH.
19 Check in the Printers window (Start menu\settings\printers) if the new
TDSx00PS printer is in the list of available printers:
8/22/2019 Oce Connectivity Manual_v1
57/274
Novell Environment 57
w Set up Windows 2000 workstation
1 From the Windows START menu, select Settings / Printers:
The Printers window is displayed:
2 Double-ClickAdd printer icon:
3 ClickNEXT.
8/22/2019 Oce Connectivity Manual_v1
58/274
58 Oc TDS/TCS Connectivity Manual
4 ClickNetwork printer radio and clickNEXT.
5 ClickNEXT. The Browse for printer window is displayed:
6 Browse the network to locate the server to which the TDSx00PS is connected:
s the correct network (NetWare Network / NetWare Servers)
s the appropriate file server (ex: SNSNW5)
s the appropriate printer queue (ex: QTDSx00PS)
8/22/2019 Oce Connectivity Manual_v1
59/274
Novell Environment 59
7 ClickNEXT. The Add Printer Wizard window is displayed, including a list
of manufacturers and printers:
8 ClickHAVE DISK.
9 ClickBROWSE.
10 Browse to locate the directory where the Oce Postscript 3 driver distribution is
located (for instance, Cd_Pack\products\TDSx00\ps3\Adobe\win2000).
11 Select the oemsetup.inf file.
8/22/2019 Oce Connectivity Manual_v1
60/274
60 Oc TDS/TCS Connectivity Manual
12 ClickOPEN. The Install from disk window is again displayed, with the
selected path appearing on the copy files from line:
13 ClickOK. The Add printer wizard window is displayed:
14 Select the Oce TDSx00PS printer.
15 ClickOK.The Digital signature not found window is displayed:
8/22/2019 Oce Connectivity Manual_v1
61/274
Novell Environment 61
16 ClickYES. Files are copied to the PC's hard disk drive, then the Default
printer window is displayed:
17 Select if you want the TDSx00PS to be the default printer or not.
18 ClickNEXT:
19 ClickFINISH. The Printers window is displayed, with the newly-installed
TDSx00PS printer in the available printers list:
8/22/2019 Oce Connectivity Manual_v1
62/274
62 Oc TDS/TCS Connectivity Manual
w Setup Windows XP workstation
1 From the Windows XP taskbar, select START / Printers and faxes:
2 ClickAdd printer:
3 ClickNEXT:
8/22/2019 Oce Connectivity Manual_v1
63/274
Novell Environment 63
4 Select Network printer and clickNext:
5 ClickBrowse for a printer and Next:
6 Browse the network to locate the server to which the TDSx00/TCS400 is
connected:
s the correct network (NetWare Network / NetWare Servers)
s the appropriate file server (e.g.: SNSNW5)
s the appropriate printer queue (e.g.: QTDSX00)
7 Click . A warning message invites you to install the driver ::
8/22/2019 Oce Connectivity Manual_v1
64/274
64 Oc TDS/TCS Connectivity Manual
8 ClickOK. The Add Printer Wizard window is displayed, including a list of
manufacturers and printers:
9 ClickHave Disk.
10 ClickBrowse:
11 Browse to locate the directory where the Oce Windows XP Postscript 3 driverdistribution is located(e.g.: \OCE\DRIVERS\PS\OCEPS3\ADOBE\WINXP).
12 Select the oemsetup.inf file.
8/22/2019 Oce Connectivity Manual_v1
65/274
Novell Environment 65
13 ClickOpen. The Install from disk window is displayed, with the selected
path appearing on the copy manufacturers files from line:
14 ClickOK.
15 Select the Oce TDSx00PS/TCS400 printer for example here in our example :
Oce TDS400 PS.
16 ClickOK. The Hardware installation window is displayed warning you are
installing a driver which has not passed Windows Logo testing:
8/22/2019 Oce Connectivity Manual_v1
66/274
66 Oc TDS/TCS Connectivity Manual
17 ClickContinue anyway. Files are copied to the PC's hard disk drive.
18 Select if you want your printer to be the default printer or not and clickNext.
8/22/2019 Oce Connectivity Manual_v1
67/274
Novell Environment 67
19 ClickFinish. The Printers window is displayed, with the newly-installed
QTDSX00 printer appearing in the available printers list:
20 Right-click on the printer installed, select Properties and print a Test page .
8/22/2019 Oce Connectivity Manual_v1
68/274
68 Oc TDS/TCS Connectivity Manual
Client Workstation setup (Autocad 14 ADI driver)
Note: Autocad 14 must be installed on the client station.
w Setup Autocad 14 ADI driver1 In the Autocad menu, select FILE / PRINTER SETUP.
The Preferences window is displayed, with the Printer thumbnail opened:
2 ClickNEW. The Add a printer window is displayed:
3Double-clickOce ADI x.x driver_For Autodesk by Oce (where x.x is thedriver release number, for instance, 4.3).
8/22/2019 Oce Connectivity Manual_v1
69/274
Novell Environment 69
The Autocad Text Window is displayed:
4 In the Supported models list, find the number corresponding to the TDSx00.
Note: Press ENTER to display the second page of the list.
5 Enter the number corresponding to the TDSx00 printer.6 Perform the requested parameters settings:
s type of printer's unit
s number of rolls
s number of trays
s folder
s ...
s The last parameter is relative to the machine connection:
8/22/2019 Oce Connectivity Manual_v1
70/274
70 Oc TDS/TCS Connectivity Manual
7 Select N for Network port. The Browse for printer window is displayed:
8 Locate the TDSx00 on the network by selecting:
s the network (Netware network / Netware servers)
s the file server (for instance, SNSNW5)
s
the printer queue (for instance, QTDSx00)
9 ClickOK. A message is displayed: Do you want to change anything?.
10 ClickN and press RETURN to validate the settings. The TDSx00 is now
added to the available printers list, in the Printer thumbnail of the
Preferences window:
11 ClickOK to finish the procedure and display the Autocad main window.
8/22/2019 Oce Connectivity Manual_v1
71/274
Novell Environment 71
Client Workstation setup (Autocad 2000/HDI1 & Autocad
2000i/HDI2)
Note: Autocad 2000 or Autocad 2000i must be installed on the client station.
w Install the Autocad 2000/HDI1 or Autocad 2000i/HDI2 drivers
1 In the Autocad menu, select FILE / PLOTTER MANAGER.
2 Double-click the Add-a-plotter wizard icon.
3 ClickNEXT. The Add Plotter- Begin window is displayed:
8/22/2019 Oce Connectivity Manual_v1
72/274
72 Oc TDS/TCS Connectivity Manual
4 Select Network plotter server and clickNEXT:
5 ClickBROWSE:
6 Locate the TDSx00 on the network by selecting:s the network (Netware network / Netware servers)
s the file server (for instance, SNSNW5)
s the printer queue (for instance, QTDSx00)
8/22/2019 Oce Connectivity Manual_v1
73/274
Novell Environment 73
7 ClickOK.The selected printer name is displayed in the Add plotter- network
plotter window:
8 ClickNEXT:
9 Select Oce in the Manufacturers list and OceTDSx00 in the Models list.
10 ClickNEXT twice:
8/22/2019 Oce Connectivity Manual_v1
74/274
74 Oc TDS/TCS Connectivity Manual
11 Enter a new printer name, if required and clickNEXT.
12 ClickEdit plotter configuration.
13 ClickCustom properties.The Custom properties button will appear in the
Access custom dialogue part of the window.
14 ClickCUSTOM PROPERTIES.
15 Setup the printer parameters.
16 ClickOK.
The Plotter configuration Editor window is again displayed.
17 ClickOK.
18 ClickFINISH.
8/22/2019 Oce Connectivity Manual_v1
75/274
Novell Environment 75
Client Workstation setup (WPD driver)
This section is a System Administrator guideline to use the Oc
TDSx00/TCS400 Print Services on a Windows Client workstation with the
Windows Printer Driver (WPD), interconnected via the Novell IPX/SPX
protocol.
The client workstations have access to the Oc TDSx00/TCS400 Print
Services via Printer Queues defined on this dedicated Novell File Server.
There are two methods to install Windows Printer Driver (WPD):
s Setup.exe: recommended method due to the complete automatic uninstall
procedure.
s Add Printer method: the full uninstall procedure may have manual actions(refer to Oc Windows Printer Driver Getting Started for further details on
uninstallation). However this method can be chosen in case of troubles with
Novell Client capture problem (see page 79).
Note: Windows Printer Driver is not available for Windows 9x/Me.
w Install WPD using the setup.exe method
1 Open the Windows Explorer.
2 Browse to locate the directory where the Oce Windows Printer Driver(WPD) distribution is located (for instance, E:\OCE\DRIVERS\WPD)::
3 Double-clicksetup.exe.
8/22/2019 Oce Connectivity Manual_v1
76/274
76 Oc TDS/TCS Connectivity Manual
4 Choose the setup language. The Oce WPD installation installer is launched:
5 ClickNEXT:
6 ClickNEXT to accept the license:
7 Select the language and clickNext.
8/22/2019 Oce Connectivity Manual_v1
77/274
Novell Environment 77
8 Choose the Printer Model and the port. For the port, select an unused port (like
LPT3: in our example).
Note: In the next procedure, the port will be redirected to the appropriate
Novell queue .
9 Enter the Printer name, choose whether you want it to be the default printer
and whether you want to print a test page.
8/22/2019 Oce Connectivity Manual_v1
78/274
78 Oc TDS/TCS Connectivity Manual
10 ClickNext. Files are copied on the Hard Disk. Two different windows
may appear.
s If the following window is displayed, no reboot is required (for example:
when you install the driver for one printer for the first time) and you can
finish the installation:
s If the second window is displayed, a reboot is required (for example: you
already installed the driver for 1 printer, and you install a new printer model).
You can finish the installation (clickFINISH), but reboot will be necessary
before using the driver.
8/22/2019 Oce Connectivity Manual_v1
79/274
Novell Environment 79
w Redirect the local port to the appropriate Novell Queue.
Note: It is preferable to use the Novell capture procedure rather than the
net use command:
1 Right-click on the N red logo on the right Task bar to launch the Novell
capture tool:
2 Select the Novell capture menu :
3 Enter the port to capture (LPT3 in this example):
4 Browse the Novell Queue:
8/22/2019 Oce Connectivity Manual_v1
80/274
80 Oc TDS/TCS Connectivity Manual
5 Do not forget to enable the option Check to always capture this port when
you start Windows and validate the capture by clicking capture:
The following window acknowledges the successful capture operation:
6 ClickOK to finish the capture.
7 Close the capture window.
8/22/2019 Oce Connectivity Manual_v1
81/274
Novell Environment 81
w Check if the setup is correct
1 From the Windows Start menu, select Settings\Printers:
2 Right-click on the printer installed, select Properties, and print a Test page:
Caution: You may wait until the polling delay (TDSx00/TCS400 Settings
Editor /Connectivity/Novell/Queue Poll Interval) before test page is
printed.
8/22/2019 Oce Connectivity Manual_v1
82/274
82 Oc TDS/TCS Connectivity Manual
w Install WPD using the Add printer method
1 From the Windows Start menu, select Settings and Printers:
2 Double-clickAdd printer.
3 ClickNetwork printer server then NEXT.
4 Browse the network to locate the server to which the TDSX00 is connected:
s the correct network (NetWare Network / NetWare Servers)
s the appropriate file server (e.g.: SNSNW5)
s the appropriate printer queue (e.g.: QTDSX00)
8/22/2019 Oce Connectivity Manual_v1
83/274
Novell Environment 83
5 ClickOK. A warning message is displayed:
6 ClickOK. The Add Printer Wizard window is displayed, including a list ofmanufacturers and printers:
7 ClickHAVE DISK:
8 ClickBROWSE to locate the directory where the Oce Windows Printer
Driver distribution is:
9 Select the oemsetup.inf file.
10 ClickOPEN.
8/22/2019 Oce Connectivity Manual_v1
84/274
84 Oc TDS/TCS Connectivity Manual
The Install from disk window is again displayed, with the selected path
appearing on the copy Manufacturers files from line:
11 ClickOK:
12 Select the appropriate printer (here Oce TDS400 1.3 printer).
13 ClickOK. Files are copied to the PC's hard disk drive:
14 ClickFINISH.15 Check the new QTDSX00 printer appears in the available printers list:
8/22/2019 Oce Connectivity Manual_v1
85/274
Novell Environment 85
16 Right-click on the printer installed, select Properties, and print a Test page:
Caution: You may wait until the polling delay (TDSX00/TCS400 Settings
Editor /Connectivity/Novell/Queue Poll Interval) before test page is
printed.
8/22/2019 Oce Connectivity Manual_v1
86/274
86 Oc TDS/TCS Connectivity Manual
Queue Based Printing Troubleshooting
This section describes a list of troubleshooting items you can find during
Queue Based Printing setup. It is aimed at the Local Network Administrator
and/or End User.
No printing occur
If no printing occurs once all settings (Oc TDSx00/TCS400 + Novell Server
+ Client workstation) have been done:
s You can check the Print Server embedded in Oc TDSx00/TCS400 is
correctly connected to the Novell Server by checking on the Novell Server
itself: normally there is an active connection on print server (PSTDSX00)
which must appear in the Netware 5 Console Monitor / Connection availableoption with the status: NORMAL
s If the Print Server is not present in Netware 5 Console connection status,
reboot the Oce TDSx00/TCS400
s If the Print Server is present in Netware 5 Console connection status, but the
status is AUTHENTICATED: Delete the Print Server connection on NovellServer, then Reboot the Oce TDSx00/TCS400
Printing occurs after a while Normally, the controller polls for job every XX
seconds, XX is set in Oce TDSx00/TCS400 controller (Settings Editor) andthe
default value is 30 seconds, so printing may occur by default 30 seconds after
having submitted the job.
8/22/2019 Oce Connectivity Manual_v1
87/274
Novell Environment 87
Print Server Name problem It is not recommended to mix lower case and upper
case characters when naming Print server, printer Queue and Printer. More
generally, check you follow standard object naming conventions:
s ...Not all print server names will be valid...
Service Advertising Protocol (SAP) names. For example,
SAP names may not exceed 47 characters, they cannot containspaces, and they must be in all-caps. In addition,
many double-byte characters used on certain code pages are
not valid SAP characters.
Novell Capture not persistent with port LPTX: When using Novell capture to
redirect LPTX: port to Novell Queue, after rebooting Windows, the capture is
not active again albeit the check box Check to always capture this port when
you start Windows has been checked. In this case, rather put a capture
command line in the Novell login scripts (ask your Novell Administrator forthat purpose).
My job name is LPT3 in Oce TDSx00/TCS400 Queue Manager Cause is that the
driver port is LPT3, and LPT3 has been redirected to Novell Queue (capture).
To avoid this problem, you have to avoid the capture, see the other alternatives
for installing a driver in the relevant section.
I cannot see PSERVER on Novell server Monitor connection section Check you
have not exceeded the maximum number of authorized licenses (Use NLS forthat purpose: ask your Novell Administrator)
NDS CONTEXT name problem? On Oce TDSx00/TCS400 controller settings
(Novell section), you can either use the typeful or typeless convention when
entering the NDS context name:
s NDS context: SNS.OCE(typeless notation) OR
s NDS context: OU=SNS.O=OCE(typeful notation)
In the case of Country addition, it is highly recommended to use the typeful
convention:
s NDS context: OU=SNS.O=OCE.C=FR
(Do not use NDS context: SNS.OCE.FR)
8/22/2019 Oce Connectivity Manual_v1
88/274
88 Oc TDS/TCS Connectivity Manual
Windows cannot connect to the printer when adding a printer driver under Windows
XP If you encounter such a windows message when adding a Printer driver:
Check:
s If the Print Server is not present in Netware Console connection status,
reboot the Oce TDSX00/TCS400
s If the Print Server is present in Netware Console connection status, but the
status is AUTHENTICATED: Delete the Print Server connection on Novell
Server, then Reboot the Oce TDSX00/TCS400
Printer driver setup error under Windows XP
When installing a driver under windows XP with Add printer method, you
may have the following error window just after the driver files are copied to
the system folder:
Check whether the driver officially supports Windows XP. The problem can
occur with PS3 driver of which release is 1.5 (not Windows XP compatible).
Others
Always check:
s you have the last Novell Support pack for your Novell Server
s
you have the last Novell client for your Operating Systems you have the last patches for your Novell client
Note: Consult Novell site (www.novell.com).
8/22/2019 Oce Connectivity Manual_v1
89/274
Novell Environment 89
NDPS Setup
Novell Distributed Print Services (NDPS)
Note: The NovellDistributed Print ServicesTM(NDPSTM) is the default and
preferred print system in NetWare 5TM.
A Printer Agent (representing all the printer characteristics) is defined on
Novell Server. A client sends jobs to the printer on the Novell server. The
Novell server sends the job(s) to the Oc TDSx00/TCS400 through a Novell
Gateway by using lpr protocol. NDPS Manager manages the printer Agent.
The NDPS broker Resource Management Service (RMS) component allowsresources (printer drivers, printer definition files, banners, and fonts) to be
installed in a central location and then downloaded to clients, printers, or any
other entity on the network that needs them.
[2] Overview of NDPS
Configuration You need to configure the Client Workstation, the Oc
TDSx00/TCS400 controller and the NOVELL Server.
Note: The Peer-to-Peer connection does not exist on NDPS.
w Setup
1 Setup the Oc TDSx00/TCS400 Controller
2 Setup the Novell Server
3 Setup the client workstation (driver installation)
8/22/2019 Oce Connectivity Manual_v1
90/274
90 Oc TDS/TCS Connectivity Manual
Controller Setup
In NDPS environment, the Novell Server sends jobs to the TDSx00/TCS400
controller by means of the LPR protocol, so this protocol must be enabled on
Controller.
w Enable the LPR protocol.
Note: You MUST be logged as a System Administrator.
1 Switch the Oc Setting Editor in SA Mode (seeSwitch the Oc Setting Editor
in SA Mode on page 267).
2 Expand the Connectivity Folder.
3 Expand the LPD folder.
4 Select Enable LPD document.
5 Select Enabled on the right window (Enable LPD):.
6 ClickApply.
7 Reboot the controller (seeReboot the controller on page 272).
8/22/2019 Oce Connectivity Manual_v1
91/274
Novell Environment 91
Novell Server Setup
This section is aimed at the Local Network Administrator and describes how
to setup the Novell Server to prepare NDPS environment printing:
1 Create a NDPS Manager2 Create a Printer Agent
3 Configure the NDPS broker Resource Management Service (RMS)
FIrst, you have to check whether the NDPS component is installed on the
Novell Server; otherwise, install it (refer to Your Novell Netware installation
manual).
Create a NDPS Manager
The NDPS Manager is used to create and manage server-based Printer Agents
(similar to the way PSERVER is used on servers to manage printing resources
in legacy printing). You must create an NDPS Manager on each server you will
be controlling NDPS printers from.
Note: You MUST be logged in as Novell System Administrator on any Windows
WorkStation running Novell Client 32 over any MS Windows operating System.
w Launch the Administrator task
1 Logon as System Administrator, using the proper Context, Tree and Server.
2 Launch the Novell Administration Task (Nwadmn32.exe) located in.
\\Novell_Server\SYS\public\WIN32 (also generally mapped on Z:\Win32.)
8/22/2019 Oce Connectivity Manual_v1
92/274
92 Oc TDS/TCS Connectivity Manual
In the following steps, objects are created using Novell Administration
console. You just need to select the existing object where you want to add a
new one, then create a new object by either:
s Netware Administrator/Object/Create action
s Right click on the container where the new object is added
s or press the INS key
In our example, we create a Container (an Organisation Unit =
NDPS_PRINTERS) where we create all the objects for NDPS printers.
8/22/2019 Oce Connectivity Manual_v1
93/274
Novell Environment 93
w Create a NDPS Manager
1 Select NDPS_PRINTERS and create a new object:
2 Give the name, Server to run on, and volume location:
Attention: To autoload the NDPS Manager when you restart the Novell
server, add the following line to your servers autoexec.ncf file (otherwise,
the NDPS manager will not be loaded after rebooting the Novell Server):
load ndpsm NDPS Manager name and context
For instance, in this example, the following line must be added:
load ndpsm .OceNDPS_Manager.NDPS_PRINTERS.SNSESC
8/22/2019 Oce Connectivity Manual_v1
94/274
94 Oc TDS/TCS Connectivity Manual
NDPS Printer Agent
NDPS printers must be represented by a logical entity known as a Printer
Agent. No Printer Agent can represent more than one printer, and no printer
can be represented by more than one Printer Agent.
The Printer Agent lies at the heart of NDPS, combining the functionspreviously performed by a printer, print queue, print server, and spooler into
one intelligent and simplified entity.
Note: You MUST be logged in as Novell System Administrator on any Windows
WorkStation running Novell Client 32 over any MS Windows operating System.
w Launch the Administrator task
1 Logon as System Administrator, using the proper Context, Tree and Server
2 Launch the Novell Administration Task (Nwadmn32.exe) located in.\\Novell_Server\SYS\public\WIN32 (also generally mapped on Z:\Win32.)
In the following steps, objects are created using Novell Administration
console, you just have to select the existing object where you want to add a new
object, then create a new object by either:
s Netware Administrator/Object/Create action
s Right click on the container where the new object is added
s or press the INS key
3 Before creating the Printer Agent, check whether there is an object NDPS
broker already running. If not, you may have trouble to create a Printer Agent.
8/22/2019 Oce Connectivity Manual_v1
95/274
Novell Environment 95
To check whether an NDPS broker object is active, search for a 3 interlaced
triangles object with Netware Administrator console:
If not present, NO NDPS broker is installed, go to section NDPS broker setup
(see page 99).
If present, double-click on it, and check the status in the identification section:
sIf Status is NDPS broker state down, go to section NDPS broker setup
sIf Status is NDPS broker state active go to next step
For example, NDPS broker state active:
8/22/2019 Oce Connectivity Manual_v1
96/274
96 Oc TDS/TCS Connectivity Manual
w Create the Printer Agent
1 Select NDPS_PRINTERS.
2 Create an NDPS printer object:
3 Enter the printer name: :
4 Press Create then:
s Enter the Printer Agent name
s Enter the NDPS Manager (you previously created)
s Enter the Novell printer gateway
8/22/2019 Oce Connectivity Manual_v1
97/274
Novell Environment 97
5 The following window may appear if NDPS manager was not already loaded.
Confirm by pressing OK:
You should see the successful following window:
Note: This window does not appear if NDPS manager was already loaded.
6 Select Printer type: NONE.
7 Select Connection type to Remote (LPR on IP):
8/22/2019 Oce Connectivity Manual_v1
98/274
98 Oc TDS/TCS Connectivity Manual
8 Enter the IP address (preferred than hostname which requires DNS resolution
on Novell Server) and the Printer name:
9 ClickFINISH to trigger the Printer Agent creation and starting.
10 Select NONE on every Operating System tab, and click CONTINUE: :
11 ClickOK to finish.
8/22/2019 Oce Connectivity Manual_v1
99/274
Novell Environment 99
NDPS Broker setup
The Broker provides three network support services not previously available
in NetWare:
s Service Registry Service (SRS),
s Event Notification Service (ENS),s Resource Management Service (RMS): RMS is the one we use below.
The RMS service allows resources (printer drivers, ) to be installed in a
central location and then downloaded to clients, printers, or any other entity on
the network that needs that resource.
When NDPS is first installed in an NDS tree, a Broker object is created
automatically in the container where the Server object resides. A broker should
then exist and run on your Novell Server. If not, refer to Create a NDPS brokerobject on page 101.
Note: You MUST be logged in as Novell System Administrator on any Windows
WorkStation running Novell Client 32 over any Windows operating System.
w Launch the Administrator task
1 Logon as System Administrator, using the proper Context, Tree and Server
2 Launch the Novell Administration Task (Nwadmn32.exe) located in.
\\Novell_Server\SYS\public\WIN32 (also generally mapped on Z:\Win32.)
8/22/2019 Oce Connectivity Manual_v1
100/274
100 Oc TDS/TCS Connectivity Manual
In the following steps, objects are created using Novell Administration
console. You just have to select the existing object where you want to add a
new object, then create a new object by either:
s Netware Administrator/Object/Create action
s Right click on the container where the new object is added
s or press the INS key.
3 Check whether there is an object NDPS broker already running, if not the case
follow the below instructions; otherwise, go to next procedure.
To check whether an NDPS broker object exists, search for a 3 interlaced
triangles object with Netware Administrator console:
If not present, NO NDPS broker is installed, go to section NDPS Broker
setup on page 99.
If present, double click on it, and check the status in the identification section:
sIf Status is NDPS broker state down, go to section NDPS Broker setup
on page 99
sIf Status is NDPS broker state active go to NDPS Broker RMS setup on
page 103.
8/22/2019 Oce Connectivity Manual_v1
101/274
Novell Environment 101
w Create a NDPS broker object
1 Select NDPS_PRINTERS and create a new object.
2 Create an NDPS broker object:
3 Specify Broker name and RMS volume
4 ClickCreate.
5 Load NDPS broker.
8/22/2019 Oce Connectivity Manual_v1
102/274
102 Oc TDS/TCS Connectivity Manual
6 Once the object is created, double click on it
Check the status field:
7 To activate it, you have to load the broker module on Novell Server:
8 Check that NDPS broker state is now active.
Attention: To autoload the NDPS Broker when you restart the Novell server,
add the following line to your servers autoexec.ncf file (otherwise, the
NDPS broker will not be loaded):
load broker NDPS Broker name and context
For instance, in this example, the following line must be added:
load broker .NDPS_BROKER.NDPS_PRINTERS.SNSESC
8/22/2019 Oce Connectivity Manual_v1
103/274
Novell Environment 103
NDPS Broker RMS setup
This section describes how to setup the Novell Server NDPS Broker Resource
Manager Service for automatic driver upload, taking the example of the
Windows Printer Driver (WPD). The RMS service allows resources (printer
drivers, ) to be installed in a central location and then downloaded to clients,
printers, or any other entity on the network that needs that resource.
Note: You MUST be logged in as Novell System Administrator on any Windows
WorkStation running Novell Client 32 over any MS Windows operating System.
w Launch the Administrator Task
1 Logon as System Administrator, using the proper Context, Tree and Server
2 Launch the Novell Administration Task (Nwadmn32.exe) located in.
\\Novell_Server\SYS\public\WIN32(also generally mapped on Z:\Win32.)
In the following steps, objects are created using Novell Administration
console. You just have to select the existing objects where you want to add a
new object, then create a new object by either:
s Netware Administrator/Object/Create action
s Right click on the container where the new object is added
s or press the INS key
8/22/2019 Oce Connectivity Manual_v1
104/274
104 Oc TDS/TCS Connectivity Manual
3 Double-click on the NDPS broker to open it, and press the Resource
Management (RMS) tab:
4 ClickAdd resources, and select the Operating System you want to add
drivers resources for.
Caution: Windows Printer Driver (WPD) only supports Windows NT4
/20 00/XP operating systems.
8/22/2019 Oce Connectivity Manual_v1
105/274
Novell Environment 105
5 Select the Windows Platform (Windows 2000 in our example) and clickAdd,
then browse to select the Printer driver, and clickOK,
6 The following window appears, press OK to install the resources .
You can see the drivers installed on Novell Server:
8/22/2019 Oce Connectivity Manual_v1
106/274
106 Oc TDS/TCS Connectivity Manual
w Assign to the Printer Agent one resource (driver) among those available for
automatic download when configuring the client.
1 Double click on the Printer Object.
The following window is displayed:
8/22/2019 Oce Connectivity Manual_v1
107/274
Novell Environment 107
2 Click Configuration a
3 Select [Default Printer Configuration], and click Modify :
8/22/2019 Oce Connectivity Manual_v1
108/274
108 Oc TDS/TCS Connectivity Manual
4 ClickDrivers, select the Operating System (Windows 2000 in our example),
then select the driver to set as the default one (TDS400 1.3 in our example) .
5 ClickOK.
6 ClickOK again in the mother window to finish. Printer Object has for
Windows 2000 a default driver ready to be downloaded
Note: Whatever the supported drivers, you can repeat the operation for any
Operating system supported.
8/22/2019 Oce Connectivity Manual_v1
109/274
Novell Environment 109
Client WorkStation Setup
This section is aimed at the Local Network Administrator and/or End User. It
describes how to setup the Client workstation in order to use the Oc
TDSx00/TCS400 Printer resource available on the Novell server through the
NDPS method.
Note: The driver must be correctly downloaded on the Server Novell (see
NDPS Broker RMS setup on page 103). If not, you can nevertheless install
the driver locally, but you lose interest in NDPS printing facilities.
Attention: This section is NOT intended for Windows Raster Driver. The
method described here is for Windows 2000 for Windows Printer Driver
(WPD) due to driver resources on Novell Server not including Windows XPand due to the fact that Windows Printer Driver (WPD) is not yet supported
on Win 9X/Me platform.
Note: Other drivers and platforms will be described in the next release of this
manual.
w Set up the workstation under Windows 2000 with WPD driver
1 From the Windows START menu, select SETTINGS/PRINTERS and
double-clickAdd Printer:
8/22/2019 Oce Connectivity Manual_v1
110/274
110 Oc TDS/TCS Connectivity Manual
2 ClickNext and choose Network Printer::
3 ClickNext:
4 ClickNEXT to browse to search your NDPS PRINTER.
5 Click on it so that it appears in the Printer field like in the following figure:
8/22/2019 Oce Connectivity Manual_v1
111/274
Novell Environment 111
6 ClickNext. At this stage, the driver resources are automatically downloaded
from Novell Server to the local client workstation (Operating system is
automatically recognized):
7 If the resource is not available on Novell Server, a window prompts you to
install the driver:
8 Select the driver:
8/22/2019 Oce Connectivity Manual_v1
112/274
112 Oc TDS/TCS Connectivity Manual
9 Select the model of the printer:
8/22/2019 Oce Connectivity Manual_v1
113/274
Novell Environment 113
The driver resources are automatically downloaded from Novell Server to the
local client workstation:
10 The setup is complete. ClickFinish.
8/22/2019 Oce Connectivity Manual_v1
114/274
114 Oc TDS/TCS Connectivity Manual
11 From the Windows START menu, select SETTINGS/PRINTERS, right-click
on the printer and select PROPERTIES.
12 ClickPrint test page.
Note: Windows XP is not yet supported by NDPS procedures of Novell.
Nevertheless, you can use the same procedure as for Windows 2000.
8/22/2019 Oce Connectivity Manual_v1
115/274
Novell Environment 115
NDPS Troubleshooting
This section describes a list of troubleshooting items that can occur during
NDPS setup. It is aimed at the Local Network Administrator and/or End User.
Creating the Printer Agent fails because of the following error :
This is probably due to the fact a Resource Management Service is not active:
Search for a 3 interlaced triangles object with Netware Administrator console:
If not present, NO NDPS broker is installed, go to section NDPS Broker
setup on page 99.
If present, double click on it, and check the status in the identification section:
s If Status is NDPS broker state down, go to section NDPS Broker setup on
page 99
s If Status is NDPS broker state active go to NDPS Broker RMS setup on
page 103
Printing in NDPS is very slow with Novell gateway LPR printing
There is a known problem on Novell lpr client slow rate (~25 KB/s).
Ref. Novell 10057434: Printing to LPR-based printer using Novell Printer
Gateway in LPR mode results in slow delivery of print data and slow print job
processing times.
Download the Novell patch: NDPS-Post SP2/SP6 NDPS updates (Last
modified: 17OCT2001). It contains (between other) fix for lpr client.
8/22/2019 Oce Connectivity Manual_v1
116/274
116 Oc TDS/TCS Connectivity Manual
These updates are intended for any one of the following platforms:
s NetWare 5.1 with Support Pack 2 applied running NDPS 2.1.3.
s NetWare 5.0 with Support Pack 6 applied running NDPS 2.0.6.
NDPS broker setup: add resource problem: the browse button does not work
This problem was noticed on Windows 2000 Operating systemwhen browsingwhile adding a resource.
Note: This problem may also occur on other Operating System.
To solve this problem, you need to launch nwadmn32.exe with the following
option (require command line):
Z:\ win32\nwadmn32.exe /DisableTLSMGR
You cannot see the NDPS printer while browsing with Network Neighborhood
s This is a known issue for Win NT4/Win2000/Win XP platforms while it
works for Windows 9X platform, and this has an impact when trying to
create a Printer
s A workaround consists to create a Queue Object on Novell server and link it
to a NDPS printer so that Win NT4/Win2000/Win XP can browse Queue
objects. You can then create a printer on Queue Object destination, but this
method works fine on pure IP network while checksum errors may occur
whenever IPX and IP protocols are mixed. This is the reason why thismethod is not described in this manual.
Can we use NDPS with Netware 4
There is a NDPS package for Netware 4 which is obsolete so not advised.
Recommendation is to upgrade to Netware 5.X in order to use NDPS.
Others
Always check:
s you have the last Novell Support pack for your Novell Servers you have the last Novell client for your Operating System
s you have the last patches for your Novell client
s Consult Novell site (www.novell.com)
8/22/2019 Oce Connectivity Manual_v1
117/274
117
Oc TDS/TCS
Connectivity Manual
Chapter 3TCP/IP protocol
This chapter describes how to setup the Oc controller to
make it work in a TCP/IP environment.
8/22/2019 Oce Connectivity Manual_v1
118/274
118 Oc TDS/TCS Connectivity Manual
Introduction
The following sections describe:
s
How to setup the Oc TDSXXX (with XXX standing for 400, 600 or 800)controller or TCS400 controller to make it work in a TCP/IP environment.
s How to setup a dedicated workstation as a Print Server in order to work in a
Client/Server configuration.
s How to setup the client workstations for working by using:
A Peer to peer connection type
A Client/Server connection type
Illustration conventions
Here are the conventions used in the illustrations of this manual:
s [Oce_Printer]: WorkGroup / Domain Name (default value: Oce_Printer)
s [Oce_System]: Machine Name (default value: OceTDSx00)
s [Printer] & [PrinterPS]: Printer Names (default values: OceTDSx00
OceTDSx00PS)
s The SMB standard UNC used are the following:
\\[Oce_system]\[Printer] which stands for \\OceTDSx00\OceTDSx00
\\[Oce_system]\[PrinterPS] which stands for \\OceTDSx00\OceTDSx00PS
8/22/2019 Oce Connectivity Manual_v1
119/274
Chapter 3 TCP/IP protocol 119
Prerequisites
Microsoft TCP/IP Printing Service (for all Operating Systems)For all operating systems, the MicroSoft TCP/IP Printing Services must be
installed on Windows:
[3] Windows NT4 (left) and Windows 2000 (right)
[4] Windows XP
8/22/2019 Oce Connectivity Manual_v1
120/274
120 Oc TDS/TCS Connectivity Manual
LPR Protocol (for Windows 2000/XP only)
In Windows 2000/XP, for performance reasons, we strongly recommend to use
LPR port instead of TCP/IP port. Only Standard TCP/IP Port is installed and
not LPR port. First check if LPR protocol is installed; if not, see the following
procedures.
w Add LPR port under Windows 2000/XP
1 From the Start menu, select Settings and Control Panel.
2 Select Add/Remove Programs and Add/Remove Windows Components:
3 Select Other Network File and Print Services (do not check it, just highlight
it) and clickDetails.
4 Select Print services for Unix. ClickOK and Next.
5 You may be prompted for Windows 2000 installation CD.
6 ClickFinish. No reboot is required.
8/22/2019 Oce Connectivity Manual_v1
121/274
Chapter 3 TCP/IP protocol 121
w Set up LPR port under Windows 2000/XP
1 From the Start menu, select Settings/Printers then Add Printer.
2 ClickNext.
3 Select Local Printer, and uncheck the Automatic detect and install my Plug
and play printer.
4 Select Next, the window Select the Printer Port appears:
5 Select Create a new port and choose LPR port.
Note: If LPR port is not present, see Add LPR port under Windows
2000/XP on page 120.6 ClickNext and enter Print server name in the first field, then the Printer
(queue) name in the second field:
7 ClickOK. The window Add Printer Wizard allows you to install the driver.
Continue the setup to install your driver (see Server setup on page 127).
8/22/2019 Oce Connectivity Manual_v1
122/274
122 Oc TDS/TCS Connectivity Manual
General TDS-TCS setup
The following sections explain how to:
s Enable TCP/IP protocol
s Setup TCP/IP general Parameters (IP Addr, Mask, Gateway, etc.)
s Enable/Disable LPR protocol
s Enable/Disable FTP protocol
s Enable/Disable DHCP Server
s Enable/Disable DNS Server and relevant parameters
w Enable TCP/IP Protocol
Note: you MUST be logged in as system administrator.
1 Switch the Oc Setting Editor in SA Mode (see page 267).
2 Expand the Connectivity folder.
3 Expand the TCP/IP folder.
4 Expand the Adapter_x folder (x= the number of the adapter to configure). In
our example x=1 (Adapter1 is enabled).
5 Select Enable document.
6 Select Enabled on the right window (Enable).
7 ClickApply:
8 You are proposed to reboot the controller: either, clickOK and continue the
other parameters setup, or, once all the setups are done, reboot the controller
(see Reboot the controller on page 272).
8/22/2019 Oce Connectivity Manual_v1
123/274
Chapter 3 TCP/IP protocol 123
w Set up the TCP/IP parameters
Note: You MUST be logged as system administrator.
1 Switch the Oc Setting Editor in SA Mode (see page 267).
2 Expand the Connectivity folder.
3 Expand the TCP/IP folder.
4 Expand the Adapter_x folder (x= the number of the adapter to configure) x=1
in our example for adapter1.
5 Select IP address document and type in the IP address (e.g. 134.188.21.180)
into the input field in the right window.
6 Select the IP mask document and type in the IP mask (e.g. 255.255.255.0)
into the input field in the right window.
7 Select the Default gateway document and type in the Default Gateway (e.g.
134.188.21.1) into the input field in the right window.
8 If relevant, select PrimaryWins Server document and enter the Primary Wins
Server address in the right window.
9 If relevant, select Secondary Wins Server document and enter the Secondary
Wins Server address in the right window.
10 ClickApply.
11 You are then proposed to reboot the controller: either, click OK and go on with
the other parameters setup, or, once all the setups are done, reboot the
controller. See Reboot the controller on page 272.
8/22/2019 Oce Connectivity Manual_v1
124/274
124 Oc TDS/TCS Connectivity Manual
w Enable the LPR Protocol
Note: you MUST be logged as system administrator.
1 Switch the Oc Setting Editor in SA Mode (see page 267).
2 Expand the Connectivity Folder.
3 Expand the LPD folder and select the Enable LPD document.
4 Select Enabled on the right window (Enable LPD) and clickApply.
5 You are then proposed to reboot the controller: either, click OK and go on with
the other parameters setup, or, once all the setups are done, reboot the
controller. See Reboot the controller on page 272.
w Enable the FTP Protocol
Note: you MUST be logged in as system administrator.
1 Switch the Oc Setting Editor in SA Mode (see page 267).
2 Expand the Connectivity folder.
3 Expand the FTP folder and select the Enable FTP document.
4 Select Enabled on the right window (Enable FTP) and clickApply.
5 You are proposed to reboot the controller: either, click OK and go on with the
other parameters setup, or, once all the setups are done, reboot the controller.See Reboot the controller on page 272.
8/22/2019 Oce Connectivity Manual_v1
125/274
Chapter 3 TCP/IP protocol 125
w Enable the DHCP Server
Note: you MUST be logged as system administrator.
1 Switch the Oc Setting Editor in SA Mode (see page 267).
2 Expand the Connectivity folder.
3 Expand the TCP/IP folder.
4 Expand the Adapter_x folder (x= the number of the adapter to configure)
In our case x=1 for Adapter1.
5 Select the Enable DHCP document.
6 Select Enabled on the right window (Enable DHCP) and clickApply.
7 You are proposed to reboot the controller: either, clickOK and go on with the
other parameters setup, or, once all setups are done, reboot the controller. SeeReboot the controller on page 272.
8/22/2019 Oce Connectivity Manual_v1
126/274
126 Oc TDS/TCS Connectivity Manual
w Set up the DNS Server
Note: you MUST be logged as system administrator.
1 Switch the Oc Setting Editor in SA Mode (see page 267).
2 Expand the Connectivity folder.
3 Expand the TCP/IP folder and select the Domain document.
4 Enter the Domain server name in the right window.
5 Select the DNS document.
6 Enter the DNS address in the right window (e.g. 134.188.21.11).
7 ClickApply.
8 You are then proposed to reboot the controller: either, click OK and go on with
the other parameters setup, or, once all the setups are done, reboot the
controller. See Reboot the controller on page 272.
8/22/2019 Oce Connectivity Manual_v1
127/274
Chapter 3 TCP/IP protocol 127
Server setup
This section describes how to setup, in a Client/Server configuration, a local
workStation acting as an Oc TDS/TCS Print Server.
In this configuration, printer data are sent twice on the LAN:
s From the user workstation to the Print Server workstation.
s From the Print Server workstation to the Oc TDS/TCS printer controller
Updates You can update the drivers locally on the Print Server by getting the
updates from the Oc web site. You can also update any of the Client Driver
very simply (*).
Administration You can fully administrate on the Print Server the Oc
TDS/TCS Printer Resource (*).
Media Setup You can fully administrate on the Print Server the Oc TDS/TCS
Printer Media (*).
Document Setup You can fully administrate on the Print Server the Oc
TDS/TCS Printer Document Format (*).
Note: (*) When using a Windows NT, 2000 or XP Workstation as a Print Server.
Note: There is no peer to peer configuration because the client workstation is
connected directly to the TDS/TCS Controller. Thus no Print Server is defined.
8/22/2019 Oce Connectivity Manual_v1
128/274
128 Oc TDS/TCS Connectivity Manual
Print server configuration (Windows Raster Driver 2)
Note: Before you start, make sure the Microsoft TCP/IP Printing Service is
installed. See Microsoft TCP/IP Printing Service (for all Operating Systems)
on page 119.
Note: Under Windows 2000 and XP, make sure the LPR protocol is installed.
See LPR Protocol (for Windows 2000/XP only) on page 120.
w Install the driver for a TDSx00
1 Open the Windows Explorer.
2 Browse the directory where the Oce WRD2 driver distribution is located:
3 Double-clicksetup.exe. The Oce TDSx00 Printer driver installer is
launched and the End User License Agreement window opens:
8/22/2019 Oce Connectivity Manual_v1
129/274
Chapter 3 TCP/IP protocol 129
4 ClickAccept:
5 Select the LPR port corresponding to the Oc TDSx00 printer you want to use.
If the port is not already defined in the list, you need to create a new port.
6 ClickNext. The Printer installation window opens:
7 Enter a new printer name if required.
8 ClickNext.
9 ClickFinish. Appropriate files are copied to your system.
10 ClickRestart Windows now to reboot the workstation.
8/22/2019 Oce Connectivity Manual_v1
130/274
130 Oc TDS/TCS Connectivity Manual
11 From the Windows Start menu, select Settings and Printers to check if the
new TDSx00 printer is available in the printers list:
w Share the printer
1 Right-click on the printer icon in the Printers window and select sharing.
2 Clickshared and give a share name to your Printer.
8/22/2019 Oce Connectivity Manual_v1
131/274
Chapter 3 TCP/IP protocol 131
3 In Windows 2000 and XP, if you want to share the printer with workstations
running another operating system, clickAdditional Drivers.
4 Check the box corresponding to the required operating system (in our example
Win 9x/Me) and clickOK.
5 ClickOK.
6 ClickBrowse.
8/22/2019 Oce Connectivity Manual_v1
132/274
132 Oc TDS/TCS Connectivity Manual
7 Locate the oemsetup.inf file dedicated to Windows 9x and click
The Windows 95/Windows 98 Printer Drivers window opens again with the
desired path in the copy files from line:
8 ClickOK. Appropriate files are copied to your system then the Printer
Properties window opens again:
9 ClickClose.
10 In the Printers window, check that your printer is shared:
8/22/2019 Oce Connectivity Manual_v1
133/274
Chapter 3 TCP/IP protocol 133
Print server configuration (Windows Printer Driver)
Note: Before you start, make sure the Microsoft TCP/IP Printing Service is
installed. See Microsoft TCP/IP Printing Service (for all Operating Systems)
on page 119.
Note: Under Windows 2000 and XP, make sure the LPR protocol is installed.
See LPR Protocol (