Post on 04-Jun-2018
8/13/2019 National 900H (1)
1/12
National Crane Series HProduct Guide
Features, t USt rating m ft foursection boom
Multiposition Easy Reach control panel
Graphical LMI
8/13/2019 National 900H (1)
2/12
Features
Graphical LMITe Graphical Load Moment Indicator
(LMI) is standard on all Series 900Hmachines. Te LMI system displays allcrane load lifting values simultaneously
while providing real-time informationabout the crane and truck operatingsystem and includes work area definitionsystem (WADS) and operating limits.Te LMI is also weatherproof and visiblein full or low light.
"HO"style outriggerswo sets of HO- style outriggers with 6,09 m(20 ft) full span, 4,27 m (14 ft) mid span setting
with manual locks and fully retracted outriggerspread. Main outriggers are equipped withremovable ball and socket aluminum foot pads.
Options to get the job done An auger attachment is available on the
28,9 m (95 ft) boom reaching a max diggingradius of 11,8 m (39 ft) with full outrigger span
Personnel basket options are available to allowversatility in operating conditions
Easy Reach controlsTe Easy Reach control station can be tilted tothe right or left side of the crane as needed andcan be stowed in the center position for transport.Te single axis pilot operated crane controls allowsmooth operation for each crane function.
8/13/2019 National 900H (1)
3/12
Features
Performance you can rely on
Bearings on the boom and retract cables can be greased through access holes in the boom side plates
Number of internal boom parts has been reduced, deceasing service time when rebuilding the machine
Internal anti-two-block wire routing eliminates damage potential
Painting crane components before assembly reduces the possibility of rust, improves serviceability andenhances the appearance of the machine
State of the art control valve provides smoother operation. e new design eliminates parts, reducingrepair costs and improving the machines serviceability
Speedy-reeve boom tip and sheave blocks simplify rigging changes by decreasing the time needed tochange line reeving
e Series 900H is standard with 410 non-continuous rotation
Two-speed hoist provides faster winch payout and pickup of unloaded cable
e stronger standard torsion box improves rigidity, reduces truck frame ex
and reduces the need for counterweight
A control knob located on the swing motor brake release valve can be easilyadjusted to the crane operator's swing speed preference
Easy Glide boom wear pads reduce the conditions that cause boom chatter andvibration. Te net result is smoother crane operation
*Product may be shown with optional equipment.
8/13/2019 National 900H (1)
4/12
Contents
Mounting configurations
Specifications
Capacities
Dimensions
Accessories
8/13/2019 National 900H (1)
5/12
eries H
Mounting configuration
FULL CAPACITY
WORK AREA lb BARE MIN., lb GARW MIN.
lb BARE MIN., lb GARW MIN.
. MIN.
. MIN.
. MIN.
.
. MIN.
..
NOTE: BOOM SHOWN
he mounting configuration is based on an 85%stability factor. If the bare truck weight requirementsare not met, counterweight will be required. hecomplete unit must be installed on the truck inaccordance with factory requirements. Since individualtruck chassis vary, a test must be performed on the unitto verify actual stability after mounting and counter-weighting (if required). A summary of mounting andtruck requirements are:
For 180 degree working area Gross Axle Weight Rating Front (GAWR) 9072 kg
(20,000 lb)Gross Axle Weight Rating Rear (GAWR) 18 144 kg
(40,000 lb)Gross Vehicle Weight Rating (GVW) 27 216 kg
(60,000 lb)Wheelbase (WB) 6,50 m (256 in)Cab to Axle runnion (C) 4,90 m (193 in)After Frame (AF) 2,67 m (105 in) min.
Frame Section Modulus (SM) from outrigger toRSOD 327cm3(20 in3) and 759 MPa(110,000 psi) material
Bare chassis weight required for stability prior toinstallation
Front 3992 kg (8880 lb) Rear 4309 kg (9500 lb)
For 360 degree working area Optional Single Front Stabilizer (SFO)Gross Axle Weight Rating Front (GAWR) 9072 kg
(20,000 lb)Gross Axle Weight Rating Rear (GAWR) 18 144 kg
(40,000 lb)Gross Vehicle Weight Rating (GVW) 27 216 kg
(60,000 lb)Wheelbase (WB) 6,50 m (256 in)Cab to Axle runnion (C) 4,90 m (193 in)After Frame (AF) 2,67 m (105 in) min.Frame Section Modulus (SM) from front spring hanger
to end of after frame 327cm3(20 in3) and759 MPa (110,000 psi) material
Bare chassis weight required for stability prior toinstallation
Front 3992 kg (8800 lb) Rear 4309 kg (9500 lb)
Note:Chassis will require extended front frame railsfor SFO addition.
For 360 stability the truck frame must have a327 cm3(20.0 in3) section modulus [248,566 N.m(2,200,000 in-lb) RBM] minimum under the crane
frame, 245 cm3
(15 in3
) section modulus [186,424N.m (1,650,000 in-lb) RBM] at the front spring rearhanger, 163 cm3(10 in3) section modulus [124,283N.m (1,100,000 in-lb) RBM] through the front springand 49 cm3(3 in3) section modulus [37,284 N.m(330,000 in-lb) RBM] at the stabilizer attachmentpoint on each truck frame rail.
NOTE 1: Gross Vehicle Weight Rating (GVWR) isdependent on all components of the vehicle(axles, tires, springs, fame, etc.) meetingmanufacturers recommendations; alwaysspecify GVWR when purchasing trucks.
NOTE 2: Diesel engines require a variable speedgovernor and energize-to-run fuel solenoidfor smooth crane operation; electronic fuelinjection is required.
NOTE 3: All mounting data is based on a NationalCrane Series 900H with subbase and an85% stability factor.
NOTE 4: he complete unit must be installed inaccordance with factory requirements,and a test performed to determine actualstability and counterweight requirements;contact the factory for details.
NOTE 5: ransmission neutral safety interlock switchis required. ruck transmission must becapable of having a neutral safety switchadded.
8/13/2019 National 900H (1)
6/12
Specifications
Model 995H Equipped with a 8,99 m 29,0 m (29.5 ft 95 ft) four-section boom. his model can be equipped with a7,62 m 13,41 m (25 ft 44 ft) two section jib. Maximum tip height with 13,41 m (44 ft) jib is 44,63 m (148 ft).
8,83 m 29,0 m (29 ft 95 ft) four-section boom. 9FJ44M7,62 m 13,41 m (25 ft 44 ft) two-section jib
Model 9105H Equipped with a 9,69 m 32,0 m (32 ft 105 ft) four-section boom. his model can be equipped with a7,62 m 13,41 m (25 ft 44 ft) two-section jib. Maximum tip height with 13,41 m (44 ft) jib is 49,68 m (158 ft).
10,05 m 32,0 m (33 ft 105 ft) four-section boom. 9FJ44M7,62 m 13,41 m (25 ft 44 ft) two-section jib
Note: Maximum tip height is measured with outriggers/stabilizers fully extended.
Boom and jib combinations data
Available in two basic models.
8/13/2019 National 900H (1)
7/12
Series H
Specifications
H winch data
NOTICE Do not deadhead line block
against boom tip whenextending boom
Keep at least wraps ofloadline on drum at all times
Use only / in diameterrotation resistant cable with, lb breaking strengthon this machine
Maximum capacity with highspeed winch is lb
part line part line part line part line part line
Maximum Boom Length at MaximumElevation with Rigging Shown with Load
Block at Ground Level
ft boom ft
Boom and jib ft ft ft ft
part line
ft
part line
ft
t Downhaul weight lb t sheave block lb t sheave block lb t sheave block lb
Winch Cablesupplied
Averagebreakingstrength
Lift andspeed
Lift andspeed
Lift andspeed
Lift andspeed
Lift andspeed
Lowspeedwinch
/ indiameterrotationresistant
, lb lb fpm
, lb fpm
, lb fpm
, lb fpm
, lb fpm
Lift andspeed
, lb fpm
Lift andspeed
, lb fpm
Highspeedwinch
/ indiameterrotationresistant
, lb lb+ fpm
lb fpm
lb fpm
, lb fpm
, lb fpm
, lb fpm
, lb fpm
WinchStandard planetary th layer drum pull lb low speed lb burst of speed
Allowable cable pull lb
All winch pulls and speeds are shown on the fourth layer. Winch line pulls wouldincrease on the first, second and third layers. Winch line speed would decrease onthe first, second and third layers. Winch line pulls may be limited by the winchcapacity or the ANSI to cable safety factor. These are shown below:
ft boom ft
Boom and jib
ft ft ft ft ft ft
8/13/2019 National 900H (1)
8/12
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
The individual cranes load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Capacities
Series H: ft boom with ft ft jib, full span outrigger and stabilizer
CAUTION:
Do not operate crane booms, jib extensions, anyaccessories or loads within 3 m (10 ft) of live powerlines or other conductors of electricity.
Jib and boom capacities shown are maximum for eachsection.
Do not exceed capacities at reduced radii. Load ratings shown on the load rating charts are
maximum allowable loads with the outriggers properlyextended on a firm, level surface and the crane leveled andmounted on a factory recommended truck.
Always level the crane with the level indicator located onthe crane.
The operator must reduce load to allow for factors suchas wind, ground conditions, operating speeds and their
effects on freely suspended loads. Overloading this crane may cause structural collapse orinstability.
Weights on any accessories attached to the boom orloadline must be deducted from the load chart capacities.
Do not exceed jib capabilities at any reduced boomlengths.
Do not deadhead lineblock against boom tip whenextending boom or winching up.
Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine.
National Crane will send you a chart on request or you may secure needed load rating information through your nearest NationalCrane dealer.
Load chart
Note:1. All capacities are in pounds, angles in degrees and radii in feet.2. Loaded boom angles are given as reference only.3. Shaded areas are structurally limited capacities.4. Handling of personnel is only permitted with full span extension of all outrigger and
stabilizer beams.
Do not moveunloaded boom
beyond limit line
Operating radiusfrom C/L rotation
with unloaded boom
RADIUS IN FEET
HEIGHTINFEET
st Jib'
nd Jib'
BOOML
ENGTHINFEET
Structural Limit
Line with ' JibErected
Structural Limit Linewith ' Jib Erected
Stability LimitLine with lbBlock
D
.
.
A
B
C
' FULL SPANOUTRIGGER LOCK PINS MUST BE DISENGAGED
'" FULL SPAN
FULLSPANFULLSPANMID SPAN MID SPAN
STABILIZER LOCK PINS MUST BE DISENGAGED
ft ft B OOM RATED LOADS WITHOUT JIB
ftBOOM
lb
LOADEDBOOMANGLEdeg
A ft
BOOMlb
LOADEDBOOMANGLEdeg
B ft
BOOMlb
LOADEDBOOMANGLEdeg
C ft
BOOMlb
LOADEDBOOMANGLEdeg
D ft
BOOMlb
LOADEDBOOMANGLEdeg
ftBOOM
lb
LOADEDBOOMANGLEdeg
LOADEDRADIUS
ft
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
.
.
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
RATED LOAD REDUCTIONS WITH STOWED JIB
ft ft JIB STOWEDBOOM
LENGTHft
Reduce load lb
Reduce load lb
Reduce load lb
Reduce load lb
Reduce load lb
Reduce load lb
,
,
,
,
,
,
ft ft JIB RATED LOADS
ftJIBlb
LOADEDBOOMANGLEdeg
ftJIBlb
LOADEDBOOMANGLEdeg
LOADEDRADIUS
ft
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
8/13/2019 National 900H (1)
9/12
Series H
Capacities
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.The individual cranes load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Series H: ft boom with ft ft jib, full span outrigger and stabilizer
CAUTION:
Do not operate crane booms, jib extensions, anyaccessories or loads within 3 m (10 ft) of live power linesor other conductors of electricity.
Jib and boom capacities shown are maximum for eachsection.
Do not exceed capacities at reduced radii. Load ratings shown on the load rating charts are maximum
allowable loads with the outriggers properly extended on afirm, level surface and the crane leveled and mounted on afactory recommended truck.
Always level the crane with the level indicator located on thecrane.
The operator must reduce load to allow for factors such aswind, ground conditions, operating speeds and their effects
on freely suspended loads. Overloading this crane may cause structural collapse or
instability. Weights on any accessories attached to the boom or loadline
must be deducted from the load chart capacities. Do not exceed jib capabilities at any reduced boom lengths. Do not deadhead lineblock against boom tip when extending
boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine.
National Crane will send you a chart on request or you may secure needed load rating information through your nearest NationalCrane dealer.
Load chart
Do not moveunloaded boom
beyond limit line.
Operating radiusfrom C/L rotation
with unloaded boom
RADIUS IN FEET
HEIGHTINFEET
st Jib'
nd Jib
'
BOOML
ENGTHINFEET
CBA D
Structural LimitLine with ' Jib
Erected
Structural Limit Linewith ' Jib Erected
Stability LimitLine with lbBlock
.
' FULL SPANOUTRIGGER LOCK PINS MUST BE DISENGAGED
'" FULL SPAN
FULL SPANFULL SPANMID SPAN MID SPAN
STABILIZER LOCK PINS MUST BE DISENGAGED
Note:1. All capacities are in pounds, angles in degrees and radii in feet.2. Loaded boom angles are given as reference only.3. Shaded areas are structurally limited capacities.4. Handling of personnel is only permitted with full span extension of all outrigger and
stabilizer beams.
ft ft BOOM RATED LOADS WITHOUT JIB
ftBOOM
lb
LOADEDBOOMANGLEdeg
A ftBOOM
lb
LOADEDBOOMANGLEdeg
B ftBOOM
lb
LOADEDBOOMANGLEdeg
C ftBOOM
lb
LOADEDBOOMANGLEdeg
D ftBOOM
lb
LOADEDBOOMANGLEdeg
ftBOOM
lb
LOADEDBOOMANGLEdeg
LOADEDRADIUS
ft
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
.
.
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
ft ft JIB RATED LOADS
ftJIBlb
LOADEDBOOMANGLEdeg
ftJIBlb
LOADEDBOOMANGLEdeg
LOADEDRADIUS
ft
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
,
,
,
,
,
,
RATED LOAD REDUCTIONS WITH STOWED JIB
ft ft JIB STOWEDBOOM
LENGTHft
Reduce load lb
Reduce load lb
Reduce load lb
Reduce load lb
Reduce load lb
Reduce load lb
8/13/2019 National 900H (1)
10/12
Dimensions
DONOTSCALEDRAWING
DONOTSCALEDRAWING
mainlayoutSHEETOF
SCALE::WEIGHT:
ATITLE:
.
.
.
RETRACTED
.
TAILSWING
.
.
.
C/L
ROTATION
.
.
.
MOUNTING
SURFACE
.
H
,
m'RETR
ACTED
m'EXTE
NDED
H
,
m'''RETRACTED
,
m'EXTENDED
NOTE:Alldim
ensionsareinmm
inunlessotherw
isespecified
.
MOUNTING
SURFACE
G
HG
H
Weigh
t
H
mm.in
mm
.in
kg,lb
H
mm
.in
mm
.in
kg,
lb
Aboveweightsan
dcentersofgravitydonotinclud
ereservoir
,RSOD
,
jib,
PTO
,pump,be
d,
SFO
.
Weightandcentersofgravityincludeboom,w
inch,
rope,
turret,liftcylinder,frame,
controls
,
outriggers,
platfor
ms,torquebox,boomrest,
bumper,d
ownhaulweight.
8/13/2019 National 900H (1)
11/12
eries H
Accessories
Radio Remote Control Four-function radio remote control for standard unit and 6-function remotes with auger. NB6R
Steel Bulkhead BHSD
Spanish-language Danger Decals, function control labels SDDand Operators Manuals SOM
Heavy-duty personnel basket 544 kg (1200 lb) capacity steel basket with safety loops for two passengers. Gravityleveling 183 cm x 107 cm (72 in x 42 in) platform. Fast attachment and secure locking BSA-1systems. Load chart must show 1043 kg (2300 lb) minimum to operate this accessory. BSA-R1(provides rotation)
BSAY-1 BSAY-2
Winch drum Rotation Indicator WDRI
Auger option 95 ft boom only14,000 ft-lb two speed auger. Maximum digging radius 39 ft (full outriggerand stabilizers only).
Oil CoolerOil coolers recommended for duty cycle applications. OC
Hinged Vandal Cover Protector VCPWith keyed lock for LMI display.
8/13/2019 National 900H (1)
12/12
Tis document is non-contractual. Constant improvement and engineering progress
make it necessary that we reserve the right to make specification, equipment, and price
changes without notice. Illustrations shown may include optional equipment andaccessories and may not include all standard equipment.
AmericasBrazilAlphaville
MexicoMonterrey
ChileSantiago
Europe, Middle East,Africa
Czech RepublicNetvorice
FranceBaudemont
CergyDecines
GermanyLangenfeld
HungaryBudapest
ItalyLainate
NetherlandsBreda
PolandWarsaw
PortugalBaltarRussiaMoscow
U.A.E.Dubai
U.K.Buckingham
Asia - PacificAustraliaBrisbaneMelbourneSydney
ChinaBeijingChengduGuangzhouIndiaDelhiHyderabadPuneKoreaSeoul
PhilippinesMakati CitySingapore
FactoriesBrazilAlphaville
ChinaTaiAnZhangjiagang
FranceCharlieuLa ClayetteMoulins
GermanyWilhelmshaven
IndiaPune
Italy
Niella TanaroPortugalBaltarFnzeres
SlovakiaSaris
USAManitowocPort WashingtonShady Grove
Regional offices
Manitowoc - Asia PacificShanghai, ChinaTel: + Fax: +
Manitowoc - Europe, Middle East, AfricaEcully, FranceTel: + Fax: +
Manitowoc - AmericasManitowoc, Wisconsin, USATel: + Fax: +
Shady Grove, Pennsylvania, USATel: + Fax: +
ManitowocPrinted in USAForm No. HPart No. H / / M www.manitowoc.com
Regional headquarters