Post on 06-Apr-2018
Contemporary Engineering Sciences, Vol. 8, 2015, no. 30, 1433 - 1447
HIKARI Ltd, www.m-hikari.com
http://dx.doi.org/10.12988/ces.2015.59268
Measurement of the Sound Power of a Self
Propelled Nut Harvester
Massimo Cecchini, Andrea Colantoni, Danilo Monarca
Department of Agriculture, Forest, Nature and Energy (DAFNE)
University of Tuscia, Via S. Camillo de Lellis snc, 01100 Viterbo, Italy
Diego Annesi, Pietro Nataletti and Aldo Pieroni
National Institute for Insurance against Accidents at Work (INAIL)
Via Fontana Candida 1, 00040 Monte Porzio Catone (RM), Italy
Copyright © 2015 Massimo Cecchini et al. This article is distributed under the Creative
Commons Attribution License, which permits unrestricted use, distribution, and reproduction in
any medium, provided the original work is properly cited.
Abstract This document is based on the determination of the sound power of a self-propelled
machine used for harvesting nuts. To calculate the level of sound power given out by
the machine, the method defined by the UNI EN ISO 3744:2010 standard has been
adopted.
This standard provides that the machine to be examined must be placed on a
reflecting surface and the microphones must be placed all around the machine in
predetermined locations on a fictitious measurement surface.
During the realization phase of this survey it merged the existence of a lack in the
methodology between the UNI EN ISO 3744:2010 and the UNI EN ISO 4254-1:2013
“Agricultural machinery - Safety - Part 1: General requirements”.
The UNI EN ISO 3744:2010 specifies that the measurement surface to be used for
the location of the microphones is the hemisphere. For big machines, this
measurement surface is not always applicable because the upper central microphone
is located at heights unreachable with conventional poles (25-30 m). Instead, the UNI
EN ISO 3744 standard allows the utilization of a different measurement surface
(parallelepiped surface) to locate the microphones, but this surface is not mentioned
in the UNI EN ISO 4254-1:2013 standard.
Results show that the UNI EN ISO 4254-1:2013 standard could be revised
adopting the criteria of UNI EN ISO 3744 for the measurement of sound power for
agricultural machinery.
Keywords: Noise, sound power, nut harvesters
1434 Massimo Cecchini et al.
1. Introduction
In order to commercialize agriculture machines in the European market,
constructors must carry out strict safety controls to satisfy communitarian
standard and thus introducing in the market safer machines.
One of the several controls that can be carried out on machines, to guarantee
the health of the worker, is the analysis of sound power level (Carletti, 2013;
Monarca et al, 2009; Riccioni et al, 2015).
According to Shanks (2014) unexpected conflicts, confusion and
inconsistencies have been observed for the declared sound pressure levels and
sound power levels for machinery supplied in Europe.
When a specific determination of the sound power is requested, the standard to
follow is severe and complicated, therefore during the measurement phase a tool
that guarantees the reliability of the data is needed (Barnard, 2014).
Environmental conditions, the number of microphones, the source position and
the method to calculate the mean value are all parameters accurately established
and imposed. In order to obtain precise results, the levels of sound pressure must
be measured in a dozen of points for each position in which the machine must be
placed. This document is based on the determination of the sound power of a self-
propelled machine used for harvesting nuts. To calculate the level of sound power
given out by the machine, more specifically the Facma Cimina 300 S, the method
defined by the UNI EN ISO 3744:2010 standard has been adopted. This standard
provides that the machine must be placed on a reflecting surface and the
microphones must be placed all around the machine in predetermined points
located on a fictitious measurement surface defined as the lateral surface of a
parallelepiped with an area equal to S, which includes the source, its sides are
parallel to the sides of the referring parallelepiped and are located at a distance
equal to “d” (distance of measurement)
from the referring parallelepiped that includes the examined machine.
All tools and instruments utilized for this work have been provide by the INAIL
(Istituto Nazionale per l'Assicurazione contro gli Infortuni sul Lavoro, Roma,
Italy) research centre of Monte Porzio Catone (RM). The tests have taken place at
the Research Center for Agricultural Engineering of CREA-ING (Consiglio per la
Ricerca in Agricoltura e l'Analisi dell'Economia Agraria - Unità di ricerca per
l'Ingegneria Agraria) in Monterotondo (Roma) on a grassy surface and not on a
reflecting one. To remedy to this lack and to guarantee reliable data, the
measurement has been repeated using a reference sound source, thus it was
possible to characterize and verify the effect of the grass in the determination of
the sound power of the examined machine. When measuring the sound emissions
of a machine of big dimensions there are many problems to face, mainly related to
the placement of microphones in pre-defined locations at a relevant ground
elevation (up to 3 meters); a further difficulty is represented by the environmental
conditions that can easily compromise the sound data: for instance, the wind or
the noise coming from the surrounding areas can inevitably compromise the test.
Measurement of the sound power of a self propelled nut harvester 1435
2. Materials and methods
The test has been carried out in several successive days. The first day, at the
Laboratory of Physical Agents of INAIL research centre in Monte Porzio Catone,
the whole instrumentation has been tested.
2.1 Instrumentation
The instrumentation used for data acquisition during the measurement phase is:
Bruel & Kjaer “2290” model microphones, equipped with pre-amplifiers and
connecting cables; Bruel & Kjaer “7507” model sound power meter (figure 1);
Bruel & Kjaer “2711” model multiplexer with 8 channels (figure 2).
Fig. 1 - Bruel & Kjaer “7507” model sound power meter.
Fig. 2 - Bruel & Kjaer “2711” model multiplexer with 8 channels
2.2 Sources description
2.2.1 Facma Cimina 300 S
The self-propelled harvester made by Facma (Vitorchiano, Italy), model
“Cimina 300 S” (figure 3), is a one operator agricultural machine that taking
advantage of the lift effect produced by the airflow is able to harvest the nuts
directly from the ground into sacks or trailers (Monarca et al, 2009, 2012). The
harvester’s characteristics are reported in table 1.
1436 Massimo Cecchini et al.
Fig. 3 - Facma Cimina 300 S during
hazelnut harvest
Technical data Values
Length 5,760 mm
Width 1,700 mm
Operating
width
2,500 – 3,000 – 3,500
mm
Height 1,700 mm
Mass 2,330 kg
Engine model Diesel 4T VM D704 TE2
Power 61 kW
TABLE 1 - Facma Cimina 300 S:
technical data
2.2.2 Source Bruel & Kjaer type “4204”
The reference sound source utilized to characterize the testing environment is
the Bruel & Kjaer type “4204” (figure 4). This machine guarantees a constant
standardize noise in the whole surrounding area.
Fig.4 - Reference sound source Bruel & Kjaer “4204”.
2.3 Test description
Before carrying out the field test, a trial source has been installed in the
reverberation room of the INAIL laboratory.
The measurement parallelepiped necessary to calculate the sound power has
been formed around this source. This last value has been determined to
characterize the standard source verifying the data given by the manufacturer.
Then, the instruments needed for the test, placed in appropriate containers, have
been transferred to the measurement location (CREA-ING research centre in
Monterotondo).
Measurement of the sound power of a self propelled nut harvester 1437
Afterwards, in the area arranged for the sound test, the base of the measurement
parallelepiped has been delimited by iron poles inserted into the ground and
linked by a white thread, as it is provided by the UNI EN ISO 3744 standard.
To facilitate the measurement operation and, as well, for safety reasons, all the
poles have been orange coloured.
At last, the distance required by the standard between the tested machine and
the obstacles has been verified. The minimum distance of 13 meters between the
fixed obstacles and the measurement parallelepiped has been respected.
Facma, the manufacturer industry of the Cimina 300 S, provided for the
transportation, by truck, of the brand new harvester to be tested at the CREA -
ING research centre.
A specialized worker placed the machine in the centre of the basis of the
measurement parallelepiped; in order to respect the minimum distance “d” of one
meter between the measurement parallelepiped and the set one (figure 5 and 6).
Fig. 5 - Facma Cimina 300 S machine placed in the centre of the measurement
parallelepiped
Fig. 6 - Scheme of the “d” distance between the measurement and the set
parallelepiped
The measurement instrumentation has been sited on a table near the machine
and all the microphones have been placed at a variable height on apposite poles,
d = 1 m
1438 Massimo Cecchini et al.
according to a pre-determined scheme, delimited by the measurement
parallelepiped defined by the UNI EN ISO 3744 standard (figure 7 and 8).
The five sides of the measurement parallelepiped have been considered
separately; they have been divided in order to obtain the smaller number of partial
rectangular areas with a maximum side of 3d.
Microphones were placed in the centre and in every corner of each partial area,
with the exception of those corners that cross the reflecting surface where the
machine was placed.
All microphones, before the placement, have been checked using a “4231”
Bruel & Kjaer calibrator that generates a pure tone at 1 kHz and with a 94 dB
level.
To regulate the instrumentation the calibrator has been introduced in each
transmitter unit, then the potentiometer of the multiplexer Bruel & Kjaer type
“2711”, relative to the input of the microphone to calibrate, has been moved until
the display of the sound power calculator Bruel & Kjaer type “7507” showed a
sound power of 94 dB.
In order to verify if the levels obtained were reliable, this procedure has been
repeated for each microphone displacement.
To avoid the influence of temporary noises, the measurement has taken place
immediately after the placement of all microphones in the correct positions of the
surface of the side to be measured.
Fig. 7 - Scheme of the microphone locations: the internal parallelepiped contains
the machine, while on the external one the microphone positions are highlighted
Fig. 8 - The tested machine with 8 microphones at a 3 meter height
Measurement of the sound power of a self propelled nut harvester 1439
Such problem comes out because in the area is frequent the transit of trains and
low-route airplanes.
Before starting the test, the engine of Facma Cimina 300 S has been properly
heated and stabilized to the normal functioning temperature, at an engine speed of
1250 min-1.
The data were captured by the Bruel & Kjaer type “7507” sound power
calculator in the “automatic” mode. This setting has permitted, after defining the
total time and the number of subintervals relative to the side of the measurement
parallelepiped to be tested, the determination of the number of scans.
The measurement time chosen for each side has been 64 seconds and on the
basis of the number of microphones placed on each side the Bruel & Kjaer type
“2711” multiplexer has automatically established the mean time and therefore the
number of scans of each microphone location. The instrument has been sampling
continuously for 64 seconds on all microphones: the sampling time T related to
each microphone is given by the following equation:
NTmT (1)
where: Tm is the total time of measurement (in this case is 64 s)
N is the number of microphones (in this case from minimum of 5 to a
maximum of 8 for each side).
After the 64 seconds scanning the instrument has given the following values:
1. global equivalent noise level (Leq), expressed in dB and weighted A, of
sound pressure related to the single side of the measurement parallelepiped;
2. global equivalent noise level (Leq), expressed in dB not weighted (Lin),
related to each third octave frequency from 100 Hz to 10,000 Hz.
The measurement of the sound power of the point source has been carried out
similarly, but the instrument utilized is a Bruel & Kjaer type “2260 Investigator”
integrating sound level meter with the microphone placed on apposite poles
(figure 9 and 10).
The measurement of the sound power of the point source is necessary to
quantify the influence of the turf when measuring the sound power of the Facma
Cimina 300 S machine and also to verify if the correction factor reported in the
INAIL manual of good practices was correct.
Fig. 9 - Tested point source and microphone placed on apposite pole
1440 Massimo Cecchini et al.
The measurement parallelepiped located around the Bruel & Kjaer source has
been chosen according to the distances provided in the UNI EN ISO 3744
standard.
Fig. 10 - Scheme of the Bruel & Kjaer “4204” source (in the middle) and the
microphone locations around it
2.4 Testing environment
2.4.1 Testing square
The measurement has taken place on a square made of pressed ground located
at the CREA - ING research centre in Monterotondo (RM).
This square, from an obstacle distance point of view respects the characteristics
of a free sound field, but differently from what it is stated in the UNI EN ISO
3744 standard, it lacks of a reflecting surface since it is covered by grass.
To compensate this lack of conformity, a specific correction factor taking into
account the sound absorption due to the grass and reported in the INAIL manual
of good practices has been introduced.
This value must be added to the sound pressure level obtain on each surface of
the measurement parallelepiped (with the exception of the upper surface).
To verify the influence of the grass surface in the measurement, an
environmental characterization has been carried out through the sound power
detection emitted by the Bruel & Kjaer type “4204” point source, which has the
peculiarity of giving a constant value of sound emission (white noise or pink
noise); measuring the level of sound pressure in correspondence with the
microphones on the testing square and comparing the sound power calculated
with these data with the one previously measured in the INAIL reverberant room
it has been possible to quantify the influence of the grass. At the same time, the
analytic correction factor suggested by INAIL literature has been verified.
2.4.2 Environmental values
The monitoring station located near by the testing square has collected the
following climate data (mean values related to the testing days):
Mean temperature: 22°C
Atmospheric pressure: 1017 mbar
Measurement of the sound power of a self propelled nut harvester 1441
Solar radiation: 768 W/m2
Mean wind speed: 1.27 m/s
3. Results
3.1 Background noise evaluation
The background noise has been measured with a CELL type “593” integrating
sound level meter responding to the IEC 61672-1-2 (ex IEC 651) and CEI EN
61672-1-2 (ex 804 group I) standard for precision integrating sound meter.
The instrument has been previously calibrated using a CEL type 284/2 sound
calibrator responding to the IEC 942 class 1 standard. The measuring time has
always been greater than 3 minutes. Measurement operations have been repeated
3 times.
The level of sound pressure of the background noise, coming out from the
average of the 3 measurements, is equal to 49.2 + 0.7 dB(A).
3.2 Average time sound pressure level (Lpeq,T)
The average time sound pressure levels are defined by the UNI EN ISO 3744
standard as the level of sound pressure of a steady and constant sound that, during
the measurement time interval T, gives the same mean square value of sound
pressure of the variable sound in the considered time:
TT tL
Tpeq dtp
tp
Tdt
TL p
0 2
0
2
0
)(1,0
,
)(1log1010
1log10 dB (2)
3.3 Sound pressure level on the entire measurement surface (LpfA)
It is the energetic mean of the average time sound pressure levels in
correspondence of all the microphones locations on the measurement surface,
with the appropriate corrections for the background noise (K1A) and the
environmental conditions of reflection (K2A):
AApApfA KKLL 21
' (3)
where: L’pA = sound pressure level
K1A = background noise correction factor
K2A = reflection correction factor
During the test the Facma Cimina 300 S recorded a LpfA value equal to 84.4
dB(A).
Table 2 shows the LpfA values, weighted A, related to the measurement
parallelepiped sides for the Facma Cimina 300 S machine.
1442 Massimo Cecchini et al.
Facma
Cimina
300 S
Active source
Measured
LAeq
dB(A)
Attenuation
due to the
grass
Corrected
LAeq
dB(A)
Side 1 84.5 0.7 85.2
Side 2 83.3 1.7 85.0
Side 3 81.9 0.7 82.6
Side 4 75.8 1.7 77.5
Side 5 85.3 No
attenuation 85.3
L’pA 83.8
2.2 = = =
84.4
1.9
TABLE 2 - Values recorded for Facma Cimina 300 S
3.4 Measurement surface (S) Facma Cimina 300 S
It is the fictitious surface with an area S that includes the source and where the
measurement locations are placed.
The measurement surface, as the standard provides, is delimited by a reflective
plane.
In the case study the measurement surface equals to 104 m2.
3.5 Background noise correction factor (K1A)
It is the correction factor that takes into account the influence of the
background noise on the level of superficial sound power; it depends on frequency
and it is measured in decibel. For weighted levels A, the correction factors is
indicated as K1A. In this case the value is negligible because the difference
between the equivalent levels L’pA measured on the single sides of the
measurement parallelepiped and the equivalent level L’’pA of the background
noise in the location of Facma Cimina 300 S is greater than 15 dB.
3.6 Reflection correction factor (K2A)
It is the correction factor that takes into account the influence of the sounds
reflected or absorbed by the superficial level of sound power; K2A depends on
frequency and it is measured in decibel weighted A.
In this case the value is negligible because there are no reflecting objects in the
surrounding area.
3.7 Facma Cimina 300: sound power level (LW)
Generally, it is indicate as LWA and it is defined by the following equation:
0log10 SSLL pfAWA dB(A) (4)
Measurement of the sound power of a self propelled nut harvester 1443
where: S = measurement surface (m2);
So = reference surface (1 m2).
In this case it equals to 104.6 dB(A).
3.8 Bruel & Kjaer “4204”: sound power level (Lw)
The value of sound power calculated on the basis of the measurements carried
out during the field test (table 3) for the Bruel & Kjaer type “4204” source is 93.4
+ 1.7 dB(A) (table 4).
Bruel & Kjaer
“4204”
Active source
Measured LAeq
dB(A)
Side1 84.5
Side 2 83.3
Side 3 81.9
Side 4 75.8
Side 5 85.3
L’pA 83.8 2.2
S 17 m2
TABLE 3 - Measured values related to Bruel & Kjaer type “4204”
K1A = -10 log (1-10 -
0,1 ΔL)
Neglegible,
because for each
side and frequency
ΔL = L’pA - L’’pA ≥
15 dB
K2A Neglegible,
because < 0,5 dB
LpfA = L’pA - K1A - K2A 81.1 + 1.7 dB(A)
LWA = LpfA + 10 log
(S/S0)
81.1 + 12.3 = 93.4 +
1.7 dB(A)
TABLE 4 - Sound power calculation for the source Bruel & Kjaer type “4204”on
the testing square
Comparing the values certified by the manufacturer (Bruel & Kjaer), those
recorded in the reverberant room and the ones obtained during the field test, it is
clear that the grass has an irrelevant influence on the test results. Indeed, the
attenuation values introduced to correct the equivalent levels, taken from the
available data in literature, can be considered suitable for the purposes of this
experimentation.
1444 Massimo Cecchini et al.
4. Conclusions
During the realization phase of this survey it merged the existence of a lack in
the methodology between the UNI EN ISO 3744:2010 standard “Acoustics.
Determination of sound power levels of noise sources using sound pressure.
Engineering method in an essentially free field over a reflecting plane.” and the
UNI EN ISO 4254-1:2013 standard “Agricultural machinery - Safety - Part 1:
General requirements”.
To determine the sound power of agricultural machines the standard to be
followed is the UNI EN ISO 4254-1:2013, which refers to the UNI EN ISO
3744:2010 specifying that the measurement surface to be used for the location of
the microphones is the hemisphere. For big machines, this measurement surface is
not always applicable because the upper central microphone is located at heights
unreachable with conventional poles (25-30 m). Instead, the UNI EN ISO 3744
standard allows the utilization of a different measurement surface (parallelepiped
surface) to locate the microphones, but this surface is not mentioned in the UNI
EN ISO 4254-1:2013 standard. Due to this severe lack, technicians operating with
big machines are often forced to apply the parallelepiped surface not mentioned
by the UNI EN ISO 4254-1:2013 standard.
It is important to notice that the UNI EN ISO 4251-1 standard, implemented for
the first time in Italy on the 22nd of June 2006, replaced the UNI EN 1553:2001
standard, withdrawn in the same date. The new standard, for all it concerns the
sound power of agricultural machines, is just alike the previous one: perhaps,
during the ISO 4254-1 standard implementation stage at the CEN level it would
have been more proper, as it regards the determination of sound power, to
integrally refer to the EN ISO 3744 standard. Indeed, it is not clear for which
reason the measurement parallelepiped surface must be excluded for agricultural
machines, while it is accepted for other kind of machines. Because of this
standard incongruity technicians are frequently put in the conditions of operating
in a not-conforming way, due to the objective difficulty on placing microphones
at 10 or more meters above the ground.
As it concern the sound power emission, the results obtained in the
experimental trial show that, at the moment, both Facma Cimina 300 S operators
and manufacturer are enforced to follow the rules imposed by the existing
standard about safety and health at work (Machine Directive, Directive
89/391/EEC and other Directives concerning safety and health of workers at
work). In fact, workers must wear apposite individual protection devices (ear
muffs, earplugs), but at the same time they must be informed and trained as
provided by Directives concerning safety and health of workers.
The manufacturer, given that the examined machine is characterized by a sound
pressure value greater than 85 dB(A) (value recorded in real working conditions),
must report on the “utilization and maintenance” manual, as clearly required in
Measurement of the sound power of a self propelled nut harvester 1445
the “Machinery Directive”, the value of sound power obtained according to the
methodology shown in this paper.
Furthermore, the manufacturer should hypothesize and implement various
interventions that may reduce the value of sound emissions of the machine. Thus,
deep surveys to individuate all sources of sound emission on the machine are
needed and an enhancement program must be implemented.
It is possible to work on:
1. noise sources;
2. noise propagation.
As it regards these last interventions, it is important to be aware that the noise
emitted by any source can be directly spread by air or by solid (for instance,
through the machine frame).
4.1 Interventions on sources
They are always to be favoured because they remove the noise (risk) directly at
the source.
It is necessary to look for the application of noiseless functioning systems on
the machine and try to decrease the high noise of some sources.
In order to do so a deepen study on all the components of the machine is needed
(for instance trough the measure of intensity), thus the possible intervention points
can be highlighted. If the noise of the sources is caused by lacks in the designing
phase, these must be immediately removed or corrected. Then, the noise origin
must be determined:
if the noise has a mechanic origin (rotating elements, transmission
elements like gears and bushes, metallic collisions), speed and load must be
reduced, while vibrations transmitted to the surfaces must be eliminated;
if the noise has an aerodynamic origin, beside the utilization of sound
dampers, it is necessary to correct the loops and the fan functioning; rotation
noises and fluid vorticity must be eliminated.
In this specific case, since the machine functioning is based on suction (flow of
depressed air), the possibility to realize a more corrected aerodynamic flow that
permits noise reduction should be analysed.
4.2 Interventions on propagation
Interventions on propagation can be realized trough different strategies of
interventions:
damping pads: are necessary in case of vibrations transmitted to the frame
from the engine or the fans used for air suction. In the case of the machine under
examination this kind of intervention has been partly realized by the
manufacturer, but it should be improved in some points. The same kind of
intervention can be used to eliminate the continuity of extended metal structures.
1446 Massimo Cecchini et al.
Integral shrouding: is an intervention to be done when it is no longer
technically possible to reduce the noise of the source. It is required when a big
noise reduction is needed (at least 15-20 dB).
It is a very effective kind of intervention, but the costs are often high and it is
not always technically feasible.
Partial shrouding: it can be useful when it is not possible to close all the
machine, when the decrease needed is not greater than 15 dB, when the
frequencies to be lowered are medium high. Interventions of partial shrouding can
determine reduction of sound power for the operator ear between 3-5 dB and 12-
15 dB.
Worker isolation: in same cases it can be useful to isolate in a sound-
insulating cabin the operator (such intervention can be also useful against other
risks, like dust). It is a feasible and advisable kind of intervention for many noisy
machines for which a reduction of noise at the source or integral shrouding are not
reasonably practicable. For the machine under examination (self-propelled nut
harvester) the driving cab is not easily realizable because the machine must
operate in tree plantations.
References
[1] A.R. Barnard, Quantifying acoustic sources through sound power
measurements, Sound and Vibration, 48 (2014), no. 7, 8-11.
[2] E. Carletti, Revision of 2000/14/EC directive: Sound power tests
according to old or revised test methods, 20th International Congress on Sound
and Vibration 2013, ICSV 2013, 2 (2013), 1153-1160.
[3] D. Monarca, M. Cecchini, P. Biondi, F. Colopardi, M. Guerrieri, Machines
for shell fruits harvesting: technical and economic aspects, Acta Hortic., 940
(2012), 171-178. http://dx.doi.org/10.17660/actahortic.2012.940.21
[4] D. Monarca, M. Cecchini, M. Guerrieri, M. Santi, R. Bedini, A. Colantoni,
Safety and health of workers: exposure to dust, noise and vibrations, Acta Hortic.,
845 (2009), 437-442. http://dx.doi.org/10.17660/actahortic.2009.845.68
[5] D. Monarca, M. Cecchini, M. Guerrieri, M. Santi, F. Colopardi, The
evolution of the hazelnut harvesting technique, Acta Hortic., 845 (2009), 353-358.
http://dx.doi.org/10.17660/actahortic.2009.845.54
[6] S. Riccioni, M. Cecchini, D. Monarca, A. Colantoni, L. Longo, P.
Cavalletti, R. Bedini, Overview of the noise measurements process in recent
years, Contemporary Engineering Sciences, 8 (2015), no. 26, 1179-1191.
http://dx.doi.org/10.12988/ces.2015.56176
Measurement of the sound power of a self propelled nut harvester 1447
[7] E. Shanks, Sound pressure level and sound power level declarations:
Navigating the maze, INTERNOISE 2014 - 43rd International Congress on Noise
Control Engineering: Improving the World through Noise Control, (2014).
[8] UNI EN 1553:2001 Agricultural machinery. Agricultural self-propelled,
mounted, semi-mounted and trailed machines. Common safety requirements.
[9] UNI EN ISO 3744:2010 Acoustics. Determination of sound power levels
of noise sources using sound pressure. Engineering method in an essentially free
field over a reflecting plane.
[10] UNI EN ISO 4254-1:2013 Agricultural machinery-Safety-Part 1: General
requirements.
Received: September 23, 2015; Published: November 9, 2015