Post on 04-Jan-2016
description
1
MAE 5380: Advanced Propulsion
Part 1: Introduction and Chemical Equilibrium
Mechanical and Aerospace Engineering Department
Florida Institute of Technology
D. R. Kirk
2
COMBUSTION FUNDAMENTALS
CombustionTechnology
Thermodynamics• Energy Balance• Flame Temperature
Chemistry• Stoichiometry• Equilibrium• Kinetics• Emissions and Pollutants
Fluid Mechanics• Flame Propagation• Laminar / Turbulent• Diffusion• Atomization• Combustor Aerodynamics
• Rapid oxidation generating heat• Slow oxidation accompanied by relatively
little heat and no light
• Combustion transforms energy stored in chemical bonds to heat that can be utilized in a variety of ways
3
Key Combustion Concepts
1. Thermochemistry and Thermodynamics
2. Chemical Kinetics
3. Explosive and General Oxidative Characteristics of Fuels
4. Premixed Flames
5. Diffusion Flames
6. Ignition
7. Detonation
8. Emissions and Pollutants
4
1. THERMOCHEMISTRY
• Combustion stoichiometry and thermodynamics
– Balance of chemical equations
– Lean, stoichiometric, and rich fuel-to-air mixtures
– 1st Law of Thermodynamics and enthalpy of combustion
• How hot is a flame? (usually 2,000-2,500 K)
• Known Stoichiometry + 1st Law → Adiabatic Flame Temperature
• Chemical equilibrium: 2nd Law of Thermodynamics
– Important in fuel-rich combustion
– Stable species at ambient conditions begin to dissociate when T > 1,250 K
– Dissociation lowers flame temperature
– Solution technique: Minimize Gibbs Free Energy, G=H-TS
• Known P and T + Equilibrium Relations → Stoichiometry
• Adiabatic combustion equilibrium
• Equilibrium + 1st Law → Adiabatic Flame Temperature and Stoichiometry
5
2. CHEMICAL KINETICS
• Equilibrium chemistry assumes that T & P are constant for a sufficiently long time for system to reach steady-state
• While equilibrium chemistry lends insight into factors that control pollutant formation, greater understanding requires study of rates at which competing reactions proceed
• Example:
– If ↓ then T ↓ and [NO] ↓
– BUT for ↓, hydrocarbon oxidation is slow
– For finite combustor length emissions of CO and unburned hydrocarbons can ↑
• Understanding developed from basic kinetic theory → Arrhenius form
• Endothermic and Exothermic reactions (forward and backward)
• Simplified kinetics vs. detailed mechanisms
6
3. EXPLOSIVE AND GENERAL OXIDATIVE CHARACTERISTICS OF FUELS
• Explosion: very fast reacting systems (rapid heat release or pressure rise)• In order for flames to propagate (deflagrations or detonations), reaction kinetics must be
fast, i.e., mixture must be explosive• Example
• At P=1 atm, NO EXPLOSION
• If P is lowered to a few % of 1 atm: EXPLOSION
• If P is raised to 2 atm: EXPLOSION
• What are explosive limits?
• Note that explosive limits are not flammability limits– Explosion limits are P & T boundaries for a
specific fuel-oxidizer mixture ratio that separate regions of slow and fast reaction
– Flammability limits are specify lean and rich fuel-oxidizer mixture ratio beyond which no flame will propagate
H2+O2, =1T=500 ºCP=1 atm
7
HINDENBURG: MAY 6, 1937
8
4. COMBUSTION MODES AND FLAME TYPES
• Combustion can occur in flame mode
– Premixed flames
– Diffusion (non-premixed) flames
• Combustion can occur in non-flame mode
• What is a flame?
– A flame is a self-sustaining propagation of a localized combustion zone at subsonic velocities
• Flame must be localized: flame occupies only a small portion of combustible mixture at any one time (in contrast to a reaction which occurs uniformly throughout a vessel)
• A discrete combustion wave that travels subsonically is called a deflagration
• Combustion waves may be also travel at supersonic velocities, which are called detonations
• Fundamental propagation mechanisms are different in deflagrations and detonations
9
4. LAMINAR PREMIXED FLAMES• Fuel and oxidizer mixed at molecular level prior to occurrence of any significant
chemical reaction
Flame color gives indication of temperatureNot quite red: T~500-550 ºCDark red: T~650-750 ºCBright red: T~850-950 ºCYellowish red: T~1050-1150 ºCNot quite white: T~1250-1350 ºCWhite: T > 1450 ºC
10
4. LAMINAR PREMIXED FLAMES
11
PREMIXED FLAMES
• Fuel and oxidizer mixed at molecular level prior to occurrence of any significant chemical reaction
12
APPLICATION: ENGINE KNOCK• In internal combustion engines,
compressed gasoline-air mixtures have a tendency to ignite prematurely rather than burning smoothly
• This creates engine knock, a characteristic rattling or pinging sound in one or more cylinders.
• Octane number of gasoline is a measure of its resistance to knock (or its ability to wait for a spark to initiate a flame).
• Octane number is determined by comparing the characteristics of a gasoline to isooctane (2,2,4-trimethylpentane) and heptane.– Isooctane is assigned an octane
number of 100. It is a highly branched compound that burns smoothly, with little knock.
– Heptane is given an octane rating of zero. It is an unbranched compound and knocks badly.
Fla
me
Mod
eN
on-F
lam
e M
ode
(aut
oign
ition
)
13
5. DIFFUSION FLAMES• Reactants are initially separated, and reaction occurs only at interface between fuel and
oxidizer (mixing and reaction taking place)
• Diffusion applies strictly to molecular diffusion of chemical species
• In turbulent diffusion flames, turbulent convection mixes fuel and air macroscopically, then molecular mixing completes process so that chemical reactions can take place
Orange
Blue
Full range of throughoutreaction zone
14
DIFFUSION FLAME: EARTH vs. SPACE
15
4+5: LOOK AGAIN AT BUNSEN BURNER
Fuel-rich pre-mixedinner flame
Secondary diffusion flameResults when CO and Hproducts from rich inner flameencounter ambient air
• What determines shape of flame? (ANS: velocity profile and heat loss to tube wall)
• Under what conditions will flame remain stationary? (ANS: flame speed must equal speed of normal component of unburned gas at each location)
• Most practical devices (Diesel-engine combustion) has premixed and diffusion burning
16
PROPULSION SYSTEMSX-37B Orbital Test VehicleGas Turbine Engine for Propulsion
Gas Turbine Engine for Power Generation
17
5: DIFFUSION FLAMES
18
7. DETONATION
• Pure Explosion vs. Detonation (not same)
– Explosion requires rapid energy release
• An explosion does not necessarily require passage of a combustion wave through exploding medium
– Both deflagrations and detonations require rapid energy release and presence of a waveform
• To have either a deflagration or a detonation, an explosive gas mixture must exist
• Recall:
• Deflagration: a subsonic wave sustained by a chemical reaction
• Detonation: a supersonic wave sustained by a chemical reaction
19
7. PULSE DETONATION ENGINES
20
PULSE DETONATION WAVE ENGINES• Liquid methane or liquid hydrogen is ejected onto fuselage• Fuel mist is ignited, possibly by surface heating• The PDWE works by creating a liquid hydrogen detonation inside a specially
designed chamber when aircraft is traveling beyond speed of sound– When traveling at such speeds, a thrust wall is created in front of the aircraft– When detonation takes place, airplane's thrust wall is pushed forward– This process is continually repeated to propel aircraft
"...use a shock wave created in a detonation - an explosion that propagates supersonically- to compress a fuel-oxidizer mixture prior to combustion, similar to
supersonic inlets that make use of external and internal shock wave for pressurization."
21
8. EMISSIONS AND POLLUTANTS
• Major pollutants produced by combustion are:
– Unburned and partially burned hydrocarbons, CnHm
– Nitrogen oxides (NOx, NO and NO2)
– Carbon monoxide (CO)
– Sulfur oxides (SOx, SO2 and SO3)
• Subjected to legislated controls (smog, acid rain, global warming, ozone depletion, health hazards, etc.)
22
EXAMPLES OF EMISSIONS
Organic Compounds andUnburned hydrocarbons
CO emissions
Note that Clean Air Act of 1970can be clearly seen in figures
23
8. EMISSIONS AND POLLUTANTS
• Aircraft deposit combustion products at high altitudes, into upper troposphere and lower stratosphere (25,000 to 50,000 feet)
• Combustion products deposited there have long residence times, enhancing impact
• NOx suspected to contribute to toxic ozone production
– Goal: NOx emission level to no-ozone-impact levels during cruise
24
DOES COMBUSTION SCALE?
• What are limiting effects on combustion system size?• Can you burn at any scale?• Do any non-dimensional numbers exist to predict combustion scaling?
25
DETAILED EXAMPLE: DIFFUSION FLAMES• Reactants are initially separated, and reaction occurs only at interface between
fuel and oxidizer (mixing and reaction taking place)
• PW4000 Fan Engine Cutaway
• Characteristics
• Fan tip diameter: 94 inches; Length: 132.7 inches
• Take-off thrust: 52,000 - 62,000 pounds; Bypass ratio: 4.8 to 5.0
• Overall pressure ratio: 27.5 - 32.3; Fan pressure ratio: 1.65 - 1.80;
• Planes powered: Boeing 747-400, MD-11, Airbus A300-610, etc.
26
MAJOR COMBUSTOR COMPONENTSC
omp
ress
or
Tu
rbin
e
27
MAJOR COMBUSTOR COMPONENTS
• Key Questions:
– Why is combustor configured this way?
– What sets overall length, volume and geometry of device?
Com
pre
ssor
Tu
rbin
e
Air
Fuel
Combustion Products
28
COMBUSTOR EXAMPLE (F101)Henderson and Blazowski
Fuel
Com
pres
sor
Tur
bine
NG
V
29
VORBIX COMBUSTOR (P&W)
• Example of vortex enhanced combustion
• Why is turbulence helpful?
30
COMBUSTOR REQUIREMENTS
• Complete combustion (b → 1)
• Low pressure loss (b → 1)
• Reliable and stable ignition
• Wide stability limits
– Flame stays lit over wide range of p, u, F/A ratio)
• Freedom from combustion instabilities
• Tailored temperature distribution into turbine with no hot spots
• Low emissions
– Smoke (soot), unburnt hydrocarbons, NOx, SOx, CO
• Effective cooling of surfaces
• Low stressed structures, durability
• Small size and weight
• Design for minimum cost and maintenance
• Future – multiple fuel capability (?)
31
CHEMISTRY REVIEW
OHm
nCOOm
nHC mn 222 24
478.4
1m
ns
22222 478.3
278.3
4N
mnOH
mnCONO
mnHC mn
Stoichiometric Molar fuel/air ratio Stoichiometric Mass fuel/air ratio
• General hydrocarbon, CnHm (Jet fuel H/C~2)
• Complete oxidation, hydrocarbon goes to CO2 and water
• For air-breathing applications, hydrocarbon is burned in air
• Air modeled as 20.9 % O2 and 79.1 % N2 (neglect trace species)
• Complete combustion for hydrocarbons means all C → CO2 and all H → H2O
2878.332
4
12
mn
mns
• Stoichiometric = exactly correct ratio for complete combustion
32
COMMENTS ON CHALLENGES
• Based on material limits of turbine (Tt4), combustors must operate below stoichiometric values
– For most relevant hydrocarbon fuels, s~ 0.06 (based on mass)
• Comparison of actual fuel-to-air and stoichiometric ratio is called equivalence ratio
– Equivalence ratio = = stoich
– For most modern aircraft ~ 0.3
• Summary
– If = 1: Stoichiometric
– If > 1: Fuel Rich
– If < 1: Fuel Lean
33
WHY IS THIS RELEVANT?• Most mixtures will NOT burn so far away from
stoichiometric– Often called Flammability Limit– Highly pressure dependent
• Increased pressure, increased flammability limit
– Requirements for combustion, roughly > 0.8
• Gas turbine can NOT operate at (or even near) stoichiometric levels– Temperatures (adiabatic flame temperatures)
associated with stoichiometric combustion are way too hot for turbine
– Fixed Tt4 implies roughly < 0.5
• What do we do?– Burn (keep combustion going) near =1 with
some of ingested air– Then mix very hot gases with remaining air to
lower temperature for turbine
34
SOLUTION: BURNING REGIONS
Air
Com
pres
sor
Tur
bine
~ 1.0T>2000 K
~0.3
PrimaryZone
35
COMBUSTOR ZONES: MORE DETAILS
1. Primary Zone
– Anchors Flame
– Provides sufficient time, mixing, temperature for “complete” oxidation of fuel
– Equivalence ratio near =1
2. Intermediate (Secondary Zone)
– Low altitude operation (higher pressures in combustor)
• Recover dissociation losses (primarily CO → CO2) and Soot Oxidation
• Complete burning of anything left over from primary due to poor mixing
– High altitude operation (lower pressures in combustor)
• Low pressure implies slower rate of reaction in primary zone
• Serves basically as an extension of primary zone (increased res)
– L/D ~ 0.7
3. Dilution Zone (critical to durability of turbine)
– Mix in air to lower temperature to acceptable value for turbine
– Tailor temperature profile (low at root and tip, high in middle)
– Uses about 20-40% of total ingested core mass flow
– L/D ~ 1.5-1.8
36
COMBUSTOR DESIGN
• Combustion efficiency, b = Actual Enthalpy Rise / Ideal Enthalpy Rise– h=heat of reaction (sometimes designated as QR) = 43,400 KJ/Kg
34 ttRb
P TTQ
cf
• General Observations:
1. b ↓ as p ↓ and T ↓ (because of dependency of reaction rate)
2. b ↓ as Mach number ↑ (decrease in residence time)
3. b ↓ as fuel/air ratio ↓
• Assuming that fuel-to-air ratio is small:
hm
TmTmmc
f
tatfaPb
34
37
COMBUSTOR LOCATION
MilitaryF119-100
CommercialPW4000
Combustor
Afterburner• Why is AB so much longer than primary combustor?
– Pressure is so low in AB that they need to be very long (and heavy)
– Reaction rate ~ pn (n~2 for mixed gas collision rate)
38
EQUATION OF STATE
• An equation of state provides a relationship among P, T and V (or ) of a substance
• Ideal gas behavior (neglect intermolecular forces and volume of molecules themselves):
– P=RT
– Pv=RT
– PV=mRT
– R=Runiversal/MW, Runiversal=8314 J/kmol K
• Assumption is appropriate for nearly all systems we will consider in MAE 5310 since high temperatures associated with combustion generally result in sufficiently low densities for ideal gas behavior to be a reasonable approximation
Aside:
• Real gas laws try to predict true behavior of a gas better than ideal gas law by putting in terms to describe attractions and repulsions between molecules
– These laws have been determined empirically or based on a conceptual model of molecular interactions or from statistical mechanics
– Examples: van der Waals and Redlich-Kwong equations
39
1st LAW OF THERMODYNAMICSFixed Mass• In Words: Heat added to system in going
from state 1 to state 2 (Q) minus work done by system in going from state 1 to state 2 (W) equals change in total system energy (E) in going from state 1 to state 2
Control Volume• In Words: Rate of heat transferred across
control surface from the surroundings to control volume minus rate of all work done by control volume (including shaft work, but excluding flow work) equals rate of energy flowing out of control volume minus rate of energy flowing into control volume plus net rate of work associated with pressure forces where fluid crosses the control surface, called flow work
Assumptions:• CV is fixed relative to coordinate system• Properties of fluid at each point within CV, or
on the CS, do not vary with time• Fluid properties are uniform over inlet and
outlet flow areas• Only one inlet and outlet stream – keep this
form simple, but can be easily relaxed to allow for multiple inlet/outlet streams
ioioiocvcv
ioioioCVCV
iiooioCVCV
zzgVVhhwq
zzgVVhhmWQ
vPvPmememWQ
22
22
2
1
2
1
dt
dewq
dt
dEWQ
eeewq
gzVumE
EWQ
1212
12121212
2
121212
2
1
Unit massbasis (J/kg)
Unit mass basisRepresenting an instant in time
Units of Energy (J)
Units of Power (W)
40
ADDED, BUT HIGHLY IMPORTANT, COMPLEXITY
Example:
• Enthalpy often approximated as h(T)=CpT
• In combustion chemistry, enthalpy must take into account variable specific heats, h(T)=Cp(T)T
• If Cp(T) can be fit with quadratic, solution for flame temperature for certain classes of problems < 1 and T < 1,250 K leads to closed form solutions
• For higher order fits or > 1 and/or T > 1,250 K, iterative closure schemes are required for solution of flame temperature
41
IDEAL-GAS MIXTURES: SOME USEFUL FORMULAS
• Mole fraction of species i, i
• Sum of all constituent mole fraction is unity
• Mass fraction of species i, Yi
• Sum of all constituent mass fractions is unity
• Converting mole fraction to mass fraction
– MW = molecular weight
• Converting mass fraction to mole fraction i
mixtureii
mixture
iii
ii
total
i
i
ii
ii
total
i
i
ii
MW
MWY
MW
MWY
Y
m
m
mmm
mY
N
N
NNN
N
1
......
1
......
21
21
42
HOW TO CALCULATE STOICHIOMETRIC FUEL/AIR RATIO
OHm
nCOOm
nHC mn 222 24
478.4
1m
ns
22222 478.3
278.3
4N
mnOH
mnCONO
mnHC mn
• Stoichiometric Molar fuel/air ratio • Stoichiometric Mass fuel/air ratio
• General hydrocarbon, CnHm
• Complete oxidation, hydrocarbon goes to CO2 and water
• For air-breathing applications, hydrocarbon is burned in air
• Air modeled as 20.9 % O2 and 79.1 % N2 (neglect trace species)
28*78.332
4
12
mn
mns
43
ABSOLUTE (STANDARD) ENTHALPY, hi, AND ENTHALPY OF FORMATION, hºf,i
• For chemically reacting systems concept of absolute enthalpy is very valuable
• Define:
– Absolute enthalpy = enthalpy that takes into account energy associated with chemical bonds (or lack of bonds) + enthalpy associated only with T
– Absolute enthalpy, h = enthalpy of formation, hf + sensible enthalpy change, hs
– In symbolic form:
– In words first equation says:
• Absolute enthalpy at T is equal to sum of enthalpy of formation at standard reference state and sensible enthalpy change in going from Tref to T
• To define enthalpy, you need a reference state at which enthalpy is zero (this state is arbitrary as long as it is same for all species).
– Most common is to take standard state as Tref=298.15 K and Pº=1 atm (Appendix A)
– Convention is that enthalpies of formation for elements in their naturally occurring state at reference T and P are zero.
• Example, at Tref=25 ºC and Pº=1 atm, oxygen exists as a diatomic molecule, so:
• Note: Some text books use H for enthalpy per mol (Glassman), some books use h for enthalpy per mol, some use for enthalpy per mol. Use any symbol you like, just know what equations require.
refisrefifi ThThTh ,,
0,22 ,,
OfrefOf hPTh
h
44
GRAPHICAL EXAMPLE
• See Figure 2.6 and Appendix A.11 and A.12
• Physical interpretation of enthalpy of formation: net change in enthalpy associated with breaking the chemical bonds of the standard state elements and forming news bonds to create the compound of interest
Graphical interpretation of absolutely enthalpy, heat of formation and sensible enthalpy
45
COMMENTS ON TABLE 1: POTENTIAL ENERGY CHART
Mor
e E
xoth
erm
ic
More E
ndothermic
Consider two reactions:
H2+½O2 → H2O
• Heat of formation (gas): -241.83 kJ/mol
• Reaction is exothermic
½O2 → O
• Heat of formation (gas): 249.17 kJ/mol
• Reaction is endothermic
H2O → H2+½O2
• Reaction 1 going backwards
• Reaction is endothermic
46
ENTHALPY OF COMBUSTION AND HEATING VALUES
• The heat of combustion, also known as heating value or heat of reaction, is numerically equal to enthalpy of reaction, but with opposite sign
– Heat of combustion (or heat of reaction) = - enthalpy of combustion (or = - enthalpy of reaction)
• If heat of combustion (or heat of reaction) is positive → Exothermic
• If heat of combustion (or heat of reaction) is negative → Endothermic
• If enthalpy of combustion (or enthalpy of reaction) is positive → Endothermic
• If enthalpy of combustion (or enthalpy of reaction) is negative → Exothermic
• The upper or higher heating value, HHV, is the heat of combustion calculated assuming that all of water in products has condensed to liquid.
– This scenario liberates most amount of energy, hence called ‘upper’
• The lower heat value, LHV, corresponds to case where none of water is assumed to condense
47
LATENT HEAT OF VAPORIZATION, hfg
• In many combustion systems a liquid ↔ vapor phase change may occur
– Example 1: A liquid fuel droplet must first vaporize before it can burn
– Example 2: If cooled sufficiently, water vapor can condense from combustion products
• Latent Heat of Vaporization (also called enthalpy of valorization), hfg: Heat required in a constant P process to completely vaporize a unit mass of liquid at a given T
– hfg(T,P) ≡ hvapor(T,P)-hliquid(T,P)
– T and P correspond to saturation conditions
• Latent heat of vaporization is frequently used with Clausius-Clapeyron equation to estimate Psat variation with T
– Assumptions:
• Specific volume of liquid phase is negligible compared to vapor
• Vapor behaves as an ideal gas
– If hfg is constant integrate to find Psat,2 if Tsat,1 Tsat,2, and Psat,1 are known
– We will do this for droplet evaporation and combustion, e.x. D2 law
2sat
satfg
sat
sat
T
dT
R
h
P
dP
T, v diagram for heat processof water at P=1 atm
48
SELECTED PROPERTIES OF HYDROCARBON FUELS
49
ADIABATIC FLAME TEMPERATURE
• For an adiabatic combustion process, with no change in KE or PE, temperature of products is called Adiabatic Flame Temperature
– Maximum temperature that can be achieved for given concentrations of reactants
– Incomplete combustion or heat transfer from reactants act to lower temperature
• Adiabatic flame temperature is generally a good estimate of actual temperature achieved in a flame, since chemical time scales are often shorter than those associated with transfer of heat and work
• Most common is constant-pressure adiabatic flame temperature
• Conceptually simple, but in practice difficult to evaluate because requires detailed knowledge of product composition, which is function of temperature
PThPTh
PTHPTH
adprodireac
adprodireac
,,
,,
50
1st LAW FOR COMBUSTION PROBLEMS (GLASSMAN)
• Most general form (rarely used, but know what each term means)
• Note on sign of Q is negative. This is consistent with the 1st Law, but you must recall that Qp the is heat evolved, or the heat given off by the system, or the heat of combustion or heat of reaction.
p
jreactiTfTTj
iprodiTfTTi
QHHHHHn
HHHHHnH
,
00
,00
000
002
Sensible enthalpy change (kJ/mol) relative to some reference T
Sensible enthalpy changefrom T=298 to some referenceTerm is zero if reference T=298
Enthalpy of formationof products at T=298 K
Sensible enthalpy changerelative to some reference TTerm is zero if reactants enter atsome reference T
Sensible enthalpy changefrom T=298 to some referenceTerm is zero if reference T=298
Enthalpy of formationof reactants at T=298 K
51
1st LAW FOR COMBUSTION PROBLEMS (GLASSMAN)• Much more common, and what we will use in MAE 5310
p
jreactiTfTTj
iprodiTfTTi
QHHHn
HHHnH
,
,
001
002
Sensible enthalpy changerelative to T=298 K
Enthalpy of formationof products at T=298 K
Sensible enthalpy changerelative to T=298 KThis term is zero if reactantsenter the system at T=298 K
Enthalpy of formationof products at T=298 K
52
ADIABATIC FLAME TEMPERATURE (GLASSMAN)
• For an adiabatic combustion process, with no change in KE or PE, temperature of products is called Adiabatic Flame Temperature, Tad
• Maximum temperature that can be achieved for given concentrations of reactants
– Incomplete combustion or heat transfer from the reactants act to lower the temperature
• The adiabatic flame temperature is generally a good estimate of the actual temperature achieved in a flame, since the chemical time scales are often shorter than those associated with transfer of heat and work
jreacti
TfTTj
iprodiTfTTi HHHnHHHn
ad ,,
00100
53
EXAMPLE: FUEL-LEAN OCTANE-AIR COMBUSTION
• Calculate Tad of normal octane (liquid) burning in air at = 0.5
– Assume no dissociation of stable products formed
– All reactants are at 298 K and system operates at a pressure of 1 atm
– Compare results with figure
54
THERMOCHEMICAL DATA (GLASSMAN): CO2, H2O
55
THERMOCHEMICAL DATA (GLASSMAN): N2, O2
56
COMMENT ON NOTATION
jreacti
TfTTj
iprodiTfTTi
reactiireact
prodiiprod
HHHnHHHn
h
H
hNHhNH
N
h
h
H
ad
,,00100
[kJ/g]Enthalpy :
[kJ/mol]or [J]Enthalpy :
:NotationGlassman
Moles ofNumber :
[J/kmol]Enthalpy :
[J/kg]Enthalpy :
[J]Enthalpy :
:Notation Turns
57
CHEMICAL EQUILIBRIUM• So far we have calculated adiabatic flame temperature assuming complete combustion
– All fuel is completely oxidized to form CO2, H2O and excess O2 and N2 are carried through unaffected
• Assumption reasonable for T < 1250 K, but most combustion systems operate at higher T• Species that are normally stable at ambient conditions dissociate
• Concentration is determined by a balance between oxidation and formation• Balance is a function of T, P and concentration
• Note: The chemical equilibrium relations we will use still only approximate the species concentrations in a combustion process. That is, they rest on the assumption that the conditions are constant for a sufficiently long time for all the reactions to reach equilibrium
222
22
2
12
1
OHOH
OCOCO
58
ADDITIONAL PRODUCT FORMATION
• NO Dissociation: Complete Combustion
– Equivalence ratio less than or equal unity, ≤ 1
– The products formed are: CO2, H2O, O2, and N2
– Equivalence ratio greater than unity, > 1
– The products formed are: CO2, CO, H2O, H2, and N2
• WITH Dissociation
– Products formed include: CO2, CO H2O, H2, H, OH, O2, O, NO, N2, and N
– Concentration is dependent on T, P and
59
CHEMICAL EQUILIBRIUM FOR A FIXED-MASS SYSTEM
• If final temperature of combustion reaction is high enough, CO2 will dissociate
• Can calculate adiabatic flame temperature as function of ( = fraction of CO2 dissociated)
• Must consider second law: dS ≥ 0
• Composition of system will shift toward point of maximum entropy when approaching from either side, since dS is positive
• Once maximum entropy is reached no further changes since would violate second law
• (dS)U,V,m = 0
222
22
21
2
12
1
OCOCOOCO
COOCO
ifiifmix PTsnPTS ,,
60
PROPANE-AIR COMBUSTION AT 1 ATMAdopted From: Turns, S.R., Introduction to Combustion
61
2nd LAW OF THERMODYNAMICS: GIBBS FREE ENERGY
• To arrive at equilibrium relations, employ 2nd Law of Thermodynamics
• State 2nd Law in terms of Gibbs Free Energy, G=H-TS
• For a closed system at constant T and P, the Gibbs free energy is minimum at thermodynamic equilibrium
irrev
irrev
irrev
TdSVdPSdTdG
TdSVdPdHTdS
VdPdHQ
dST
QdS
0,
,
,
,
i
PTi i
i
PTi iirrev
nT
nP
dnn
G
dnn
GTdS
P
GV
T
GS
i
i
Bas
ic T
herm
odyn
amic
Rel
atio
ns
Criteria for Equilibrium
62
MORE USEFUL FORMS
• Gi=Hi-TSi
• Separate Gi into a pressure dependent and term and pressure independent term
– Recall that Cpi is not a function of pressure
• The more negative Gº is, the larger Kp is and the more spontaneous the reaction is
P
bB
aA
dD
cC
PP
bB
aA
dD
cC
T
T
ii
T
T
fii
iii
KRTG
PP
PPTKK
PP
PPRTG
dTT
CpTSTThdTCpTG
PRTTGG
ln
ln
ln
00
00
dDcCbBaA
Equation 40 i
gasiiP PTK
,
Another useful form
63
COMMENTS ON KP
1. The Kp of a reaction depends on temperature only
– Independent of pressure of the equilibrium mixture
– Not affected by presence of inert gases
2. The Kp of the reverse reaction is 1/ Kp
3. The larger the Kp, the more complete the reaction
– If Kp > 1,000 (or ln Kp > 7) reaction assumed complete
– If Kp < 0.001 (or ln Kp < -7) reaction assumed not to occur
4. Mixture pressure affects the equilibrium composition (but not Kp)
5. Presence of inert gases affects the equilibrium composition
6. When stoichiometric coefficients are doubled, the value of Kp is squared
7. Free electronic in the equilbrium composition can be treated as an ideal gas
8. Equilibrium calculations provide information on the equilibrium composition of a reaction, not on the reaction rate.
64
ADIABATIC COMBUSTION EQUILIBRIUM• Previously we have considered:
– Known Stoichiometry + 1st Law (Energy Balance) → Adiabatic Flame Temperature
• Problems 1-4
– Known P and T + 2nd Law (Equilibrium Relations) → Stoichiometry
• Problems 5-9
• Now we can combine these:
– 1st Law (Energy Balance) + 2nd Law (Equilibrium Relations) → Adiabatic Flame Temperature + Stoichiometry
• Problems 10-14
• Solution Scheme
1. Guess a T=Tguess
2. Do equilibrium calculation to solve for species concentrations at Tguess
3. Plug into 1st Law
• We want F(Tguess)=0
• If F(Tguess) > 0, then initial guess was too high
• If F(Tguess) < 0, then initial guess was too low
1. Increment Tguess
0,,
00100
jreactiTfTTj
iprodiTfTTiguess HHHnHHHnTF
ad
65
EXAMPLE: MONOPROPELLANT ROCKET PROPULSION• Monopropellant rockets are simple propulsion systems that rely on chemicals which, when energized, decompose
• Decomposition creates both the fuel and an oxidizer (which allows the fuel to burn), which then react with each other
• Because they only use a single propellant, monopropellant rockets are quite simple and reliable, but not very efficient
• Mainly used to make small adjustments such as attitude control
– Typical Specific Impulse: 100-300 sec
– Typical Thrust: 0.1-100 N
Monopropellant hydrazine (N2H4, see Problem 12) thrusters that were used for trajectory correction maneuvers (TCMs) during interplanetary cruise, thrust vector control (TVC) during VOI, orbit trim maneuvers during the mapping mission, and attitude control when the action wheels are being desaturated. The rocket motors are clustered in modules located on the end of outrigger booms in order to increase their moment arm and thus decrease attitude control propellant requirements. Twelve 0.9-N (Newton) and four 22-N rocket motors are used for attitude control, with thrust being provided by eight 445-N rocket motors or by the 0.9-N motors for small TCMs.
66
EXAMPLE: MONOPROPELLANT ROCKET PROPULSION
• Rocket propellant chemists have proposed a new, high-energy liquid oxidizer, penta-oxygen, O5, which is also a monopropellant.
• Calculate the monopropellant decomposition temperature at a chamber pressure of 10 atm. If it is assumed the only products are O atoms and O2 molecules.
• Supplemental Information:
– Heat of formation of new oxidizer is estimated to be very high: 1,025 kJ/mole
– O5 enters system at 298 K
– Amount of O2 and O should be calculated for one mole of O5 decomposing
• Solution Technique
– Solution is iterative
– In order to calculate the final temperature of the mixture, one needs to the composition of the mixture at equilibrium – but – the composition of the mixture can only be found if the final temperature is known.
– Strategy:
• Guess final temperature and calculate mixture composition using equilibrium concept
• Once composition is known at guessed temperature, adiabatic flame temperature is calculated and checked against guessed value
• Repeat process until guessed and calculated temperatures are same
– Answer lies somewhere between 4,000 and 5,000 K
67
PRACTICAL APPLICATION: RECUPERATION• A recuperator is a heat exchanger in which energy from a steady flow of hot combustion
products, called flue gases, is transferred to the air supplied to the combustion process
68
SOME COMMON TYPES OF RECUPERATORShttp://www.hardtech.es/hgg_tt_hrt.0.html
Tubes cage radiation recuperatorworking at 1,200ºC
Double shellradiation recuperator
Tubes cageradiation recuperator
Installation consistingof a tubes cage recuperatorand a double shell one,series-connected
69
EXAMPLE: RECUPERATION (TURNS)A recuperator, as shown in figure, is employed in a natural-gas-fired heating-treating furnace. The furnace operates at atmospheric pressure with an equivalence ratio of 0.9. The fuel gas enters the burner at 298 K, while the air is pre-heated.
1. Determine the effect of air preheat on the adiabatic flame temperature of the flame zone for a range of inlet air temperatures from 298 K to 1,000 K.
2. What fuel savings result from preheating the air from 298 K to 600 K? Assume that temperature of flue gases at furnace exit, prior to entering recuperator, is 1700 K, both with and without preheat.
Radiant-tube burner with coupledRecuperator for indirect firing. Note thatAll flue gases pass through the recuperatorSource: Turns, An Introduction to Combustion
70
NASA CEA PRACTICE PROBLEM
Consider combustion of a methane-air mixture at 10 atm (both fuel and air are at 10 atm).
1. Plot mole fractions, i, for the species CO2, CO, H2O, H2, OH, O2, N2, NO vs. temperature for =1 for a temperature range from 1000 to 2500 K.
2. Calculate Tflame and mole fractions as a function of for adiabatic combustion. Plot these results vs. and discuss at what value the peak flame temperature occurs. Comment on this value in light of the discussion found in Chapter 1, Part 2 of Glassman.
3. Compare Tflame from part (2) to what would be obtained assuming complete oxidation (burning in only oxygen) and what would be obtained assuming complete combustion (burning in air).