Lubricant and Release AgentFor Professional Dental Use

PULPDENT CORPORATION

PULPDENT

WINK

Water soluble lubricating solution and release agent in a convenient pump dispenser.

Not a spray.

Greaseless , water soluble formula goes on smoothly and easily and washes off quickly with water.

Replaces petroleum jelly and other greasy, lumpy, hard to remove materials.

Apply with a cotton pellet.

Thins easily with air.

WINKEnsures accuracy and patient comfort.

Saves time.

INDICATIONSLubricant for:Outside surface of restorations to facilitate

cement removal Build ups, teeth and preps when making

temporary restorationsRubber dam to facilitate placement without

tearingPULPDENT

WINKEnsures accuracy and patient comfort.

Saves time.

INDICATIONSLubricant for:Tight fitting implant abutments during try-in

phase Face and lips to prevent drying during long

proceduresHands when handling sticky materials

PULPDENT

WINKEnsures accuracy and patient comfort.

Saves time.

INDICATIONSQuick release agent for:All impression materials, even polyethersSet cement from outside surfaces of restorationsCement and impression material from face and

tissue

PULPDENT

WINKEnsures accuracy and patient comfort.

Saves time.

INDICATIONSQuick release agent for:Temporary materials from resin crown build upsAlginate impressions for diagnostic modelsBuccal surfaces of dentures during reline

procedures

PULPDENT

WINKEnsures accuracy and patient comfort.

Saves time.

PULPDENT

Even a small distortion can result in inaccurate models and restorations that do not fit properly.

Easy release of set impressions prevents the distortion caused by torque and stresses during removal from the mouth.

Have you ever struggled to remove an impression?Or remove set impression material from face and lips?

Remove them in a blink with WINK.

Just place a small amount of WINK on a cotton pellet or suitable applicator, and you’re ready to go.

WINK

PULPDENT

For easy removal of rigid final impressions, place a thin coat of Wink on facial and lingual tooth surfaces and on mucosa (but not the tooth prep when making final impressions).

WINK

PULPDENT

Apply a thin coat of WINK before making impressions

Impressions come off in a blink with WINK

WINK

NOTE:Do not place WINK on the tooth prep when making final impressions for permanent restorations.

A thin coat of WINK on face and lips makes removing set impression material from face and soft tissue a breeze.

WINK

Apply WINK to face and lips Set impression material peels off effortlessly

PULPDENT

For superior temporary restorations, lubricate preps and adjacent teeth with WINK and air thin. The set temporary material releases with ease from the teeth. Margins are crisp and easily readable.

Apply WINK witha cotton pellet

Air thin WINK Perfect temporary with crisp margins is shown in the impression

WINKFigure 1 shows WINK being placed into the inlay preparation prior to making a temporary inlay.

Figure 2 shows the temporary inlay being easily removed from the preparation.

Figure 1 Figure 2

Place a thin coat of WINK on the outside of temporary restorations and removal of set cement is quick and effortless.

WINK

PULPDENT

Note:Avoid getting WINK under the margin of temporary or permanent restorations during cementation.

WINK

PULPDENT

WINKFigure 1 shows a partial core build up.Figure 2 shows WINK being applied to the core prior to placement of the temporary material. After setting, the temporary will release easily.

Figure 1 Figure 2

WINKFigure 1 shows the custom tray with provisional material in place after WINK was applied to the four anterior teeth.Figure 2 shows the custom tray and temporary after it was easily removed. Note that the provisional material released from the mouth and stayed in the tray. Figure 3 shows the finished temporary in place.

Figure 1 Figure 2 Figure 3

WINKWINK is being placed on a natural tooth core and a partial core preparation prior to placement of provisional material. WINK is water soluble, washes off easily, and will not interfere with cementation.

WINK

NOTE:Apply WINK on the tooth prep prior to making a temporary restoration.But do not apply WINK on the tooth prep when making final impressions for permanent restorations.

WINKDuring the try-in phase for tight fitting implants, place WINK on the implant abutment prior to try-in. Even tight fitting CAD/CAM implants release with ease.

A thin coat of WINK lubricates rubber dam and facilitates placement without tearing.

WINK

PULPDENT

WINKInstructions for Use

1. Dispense a small amount of WINK into a dappen dish or mixing well.

2. Apply a thin coat of WINK on the teeth, soft tissue or the outside of the restoration. Air thin if desired.

3. WINK easily washes off with water.

Note: Avoid getting WINK under the margin of a restoration during cementation or on the tooth prep when a final impression is being made for a permanent restoration. When making an impression for a temporary restoration, applying WINK to the tooth prep is indicated.

PULPDENT

WINKCode Description _WINK 50mL Dispenser Bottle

PULPDENTPULPDENT