Post on 29-Jul-2020
The Atlas unit heaters can be supplied with the innovative JETSTREAMinduction flow optimiser, in the manual version or the motorised version for
wall-hung or ceiling installation. The lower outlet temperature of the air from
the units means less stratification of the hot air in the building and less
operating time for the same ambient temperature. In addition, the increased
air throw means greater uniformity of the temperature at floor level, with an
expansion of the comfort zone, and consequently the possibility to install
smaller and more silent appliances.
Induction Flow OptimizerJetstream
1
INFLUENCE AREA
Temp. underthe ceiling 30°C
MINUTES MINUTES
Time necessary to reachthe room temperature of 18°C
Time necessary to reachthe room temperature of 18°C
Air speed 0.25 m/s Air speed 0.1 m/s18°C
Temperatureunder the ceiling 19-20°C
18°C
INFLUENCE AREA
Technical characteristics:The use of the JETSTREAM induction flow optimizer
has the following advantages:
a) Energy saving:
– reduced hot air stratification
within the building.
– reduced operating time
of the units with the same
ambient temperature.
Energy saving varies
between a minimum of 5%
and a maximum of 15%,
with maximum amortization in two seasons.
b) Environment comfort advantages:
– increased floor-temperature uniformity
with greater comfort area.
– possibility to install smaller and quieter units,
due to the increase of the throw.
Four versions are available:
• Manual for wall installation (all sizes)
• Manual for ceiling installation (all sizes)
• Motorized for wall installation (sizes 1÷7 only)
• Motorized for ceiling installation (all sizes)
The manually controlled version calls for manual orientation
of the fins and for them to be locked using a special threaded rod.
The motorized version is supplied
with single phase motor that can be controlled by the remote switch.
Air produced by a unit heaterWITHOUT induction optimizer
Air produced by a unit heaterWITH induction optimizer
2
368
422
476
530
584
638
793
900
1010
1117
1,4
1,7
1,8
2,0
2,2
2,4
2,6
3,0
3,4
3,7
Amm
WEIGHTKg
O - 1O - 2O - 3O - 4O - 5O - 6O - 7O - 8O - 9O - 10
V - 1V - 2V - 3V - 4V - 5V - 6V - 7V - 8V - 9V - 10
MODEL
Dimensions and Weight
O (HORIZONTAL DISCHARGE)
V (VERTICAL DISCHARGE)
Controls
Remote switch
3
8
11
14
16
20
25
-
-
-
-
13
16
19
21
26
31
-
-
-
-
5,5
7,5
10
12
15
18
24
26
28
30
9
13
15
15
18
23
29
32
34
37
-
-
-
-
-
-
18
20
21
22
-
-
-
-
-
-
23
25
26
28
4
4,5
5
5,5
6
7
-
-
-
-
4
5
6,5
6,5
7
8
-
-
-
-
3
3,5
4
4,5
5
6
7
9
11
12
3
4
5,5
5,5
6
7
8
10
13
14
-
-
-
-
-
-
6
7
8
9
-
-
-
-
-
-
7
8
9
10
5,5
8
11
12
13
14
-
-
-
-
4
6,5
8
9
10
12
13
15
18
19
-
-
-
-
-
-
11
12
13
14
0123456789
0123456789
SABIANAUNIT HEATER
SIZE
SABIANAUNIT HEATER
SIZE
WITHOUT JETSTREAM
WITHOUT JETSTREAM WITH JETSTREAM
4P
4P 4P6P 6P8P 8P
4P 4P6P 6P 6P8P 8P 8P
WITH JETSTREAM AT 60° WITH JETSTREAM AT 120°
INSTALLATION HEIGHT H (m)
MAXIMUM THROW L (m)
Mounting heightsand Air throwa) Wall installation for horizontal discharge:
b) Ceiling installation for vertical discharge:
Speed 0.1 m/s
Speed0.1 m/s
Speed0.1 m/s
MAXIMUM THROW L (m)
LOUVRESINCLINATION 90°
LOW
EST
HEI
GH
T 3m
THROW 30° EVERY SIDE
60° 120°
THROW 60° EVERY SIDE
HEI
GH
T H
m
HEI
GH
TH
m
4
5JE-LT-EN
-07-14
Sabiana s.p.a. • via Piave, 53 • 20011 Corbetta • Milano • Italy
phone +39.02.97203.1 r.a. / +39.02.97270429 / +39.02.97270576
fax +39.02.9777282 / +39.02.9772820
www.sabiana.it • info@sabiana.it
The descriptions and illustrations provided in this publication
are not binding: Sabiana reserves the right, whilst maintaining
the essential characteristics of the types described
and illustrated, to make, at any time, without the requirement
to promptly update this piece of literature, any changes
that it considers useful for the purpose of improvement
or for any other manufacturing or commercial requirements.