Post on 20-Jan-2015
description
Subject:
Engineering Graphics
Branch: MechanicalClass: B2Semester: 2nd
Year: 2014Topic: Introduction
Group members Enrollment no
Prajapati Ashvinkumar 130980119079
Prajapati Hardik 130980119080
Prajapati Jay 130980119081
Prajapati Kaushik 130980119082
Introduction
Engineering means “Applied science” Graphics means “drawings” “Language of Engineers” It is a way for communicating Engineer’s ideas, designs and
thoughts to others. The communication of ideas through the graphical language. It’s helps to reduce the time, increase the accuracy of the
object to be manufacture.
Freehand drawing
The lines are sketched without using instruments other
than pencils and erasers.
Example
Instrument drawing
Instruments are used to draw straight lines, circles, and
curves concisely and accurately. Thus, the drawings are usually
made to scale.
Example
ISO International Standards Organization
Standard Code
ANSI American National Standard InstituteUSA
JIS Japanese Industrial StandardJapan
BS British StandardUK
AS Australian StandardAustralia
Deutsches Institut für NormungDINGermany
Country Code Full name
India BIS Bureau of Indian Standards
Drawing Sheet
Trimmed paper ofa size A0 ~ A4.
Standard sheet size (JIS)
A4 210 x 297
A3 297 x 420
A2 420 x 594
A1 594 x 841
A0 841 x 1189
A4
A3
A2
A1
A0(Dimensions in millimeters)
Drawing Scales
Scale is the ratio of the linear dimension of an element of an
object shown in the drawing to the real linear dimension of the
same element of the object.
Size in drawing Actual size
Length, size
:
Drawing Scales
Designation of a scale consists of the word “SCALE”
followed by the indication of its ratio, as follow
SCALE 1:1 for full size
SCALE X:1 for enlargement scales (X > 1)
SCALE 1:X for reduction scales (X > 1)
Dimension numbers shown in the drawing are correspond
to “true size” of the object and they are independent of
the scale used in creating that drawing.
Visible lines represent features that can be seen in the
current view
Meaning of Lines
Hidden lines represent features that can not be seen in
the current view
Center line represents symmetry, path of motion, centers
of circles, axis of axisymmetrical parts
Dimension and Extension lines indicate the sizes and
location of features on a drawing
Example : Line conventions in engineering drawing
Text on Drawings
Text on engineering drawing is used :
To communicate nongraphic information.
As a substitute for graphic information, in those instance where text can communicate the needed information more clearly and quickly.
Uniformity - size- line thickness
Legibility - shape- space between letters and words
Thus, it must be written with
DIMENSIONING METHOD
Aligned Dimensioning Unidirectional Dimensioning
Objectives in Drawing
Typical Drawing Equipment
Objectives in Drawing
1. Accuracy
2. Speed
3. Legibility
4. Neatness
Drawing board
It’s a rectangular wooden board 22 mm of thick and size is 650*470 mm
Drawing board must be placed on the table with working edge always to be at the left side.
Working edge
Mini drafter
It’s a combined form of T-square ,Set square Protractors and scale. One end of the drafter is Clamped at the left top end.
Drawing Pencils
High-quality drawing pencils should be used in technical drawing, never ordinary writing pencils.
HB(soft grade) – used for lettering, freehand sketching
H ( medium grade ) - used for visible outlines, edges
2H(hard grade) - used for dimension line, hidden line
Drawing sheets
The basic principle involved in arriving at the sheet size is x1:x2 = 1:√2
X1,X2 are sides of the sheet
The surface area of A0 size sheet is one square meter.
T-square
Some drawing instruments
Layout of drawing sheets
Standard form of arrangement
Important particulars are included
Facilitate quick reading of important particulars – quick references are located easily – drawings are prepared at various locations and shared
Borders
space left all around in between the trimmed edges of the sheet a minimum of 10 mm
Line types
Engineering scales
Dimensions of large objects must be reduced to accommodate
on standard size drawing sheet.
This reduction creates a scale of that reduction ratio.
This ratio is called reducing scale
Full scale 1:1
Reducing scale 1:2,1:5,1:10
Enlarging scale 2:1,5:1,10:1
Geometric construction
Point : A point is not a thing, but a place. We indicate the
position.
Line joining of two point but no breath and think
Polygon :it’s a plane figure more than 4 straight lines
Depending on the number of sides the regular polygon are
classified as
1) Rectangle, 2) Pentagon, 3) Hexagon, 4) Heptagon,
5) Octagon, 6) Nonagon.
3-1024 sides is name as polygon.
Vertical plane –when the observer is viewing it from the
front.
It shows only two dimension length and height.
Horizontal plane – when the observer is viewing it from top.
It shows only breath.
Vertical & horizontal plane
Orthographic projection
Four quadrant
First angle projection
It’s in first quadrant. Top view comes below to the front view
Third angle projection
It’s in third quadrant Top view comes above the front view
ENGINEERING CURVES