Post on 12-Jan-2016
description
Intel Platform-Calpella Introduction
Chini YangChini Yang
21 .Sep. 201021 .Sep. 2010
Agenda Agenda
Calpella Platform Block Diagram.
CPU(Clarksfield/Arrandale) & PCH(Ibex Peak-M) & EC(IT8570E) Features Introduce Briefly.
N71Ja Power On Sequence Illuminate for Detail.
Common Bugs Analyze on N71Ja/Jq.
Q & A.
Calpella PlatformCalpella Platform
Calpella vs. Montevina
Calpella PlatformCalpella Platform
Calpella PlatformCalpella Platform
Calpella-N71Ja Block Diagram Calpella-N71Ja Block Diagram
Calpella CPUCalpella CPU
Clarksfield(C) vs. Arrandale(A)
Calpella CPUCalpella CPU
Calpella PCHCalpella PCH
Calpella CLKCalpella CLK
An Important Component Platform Needed - EC
An Important Component Platform Needed - EC
Keyboard matrix/Touchpad control
Power/Charger… etc, LEDs instruct
Fan tachometer control
Power management (sleep/hibernate/wake up/Lid switch)
Power sequence control with PCH
Battery charger/Cell capacity/Temperature monitor
GPIO control
PS: If the system cannot power on, we can snatch LPC_FRAME# to make known that whether EC has worked.
Power Sequence Provision - ACPI Power State
Power Sequence Provision - ACPI Power State
G0/S0:Full on
G1/S1:CPU sleep ----PCH has the option to assert the CPUSLP# signal to further reduce processor power consumption.
G1/S3:Suspend to RAM ----The system context is maintained in system DRAM, but power is shut off to non-critical circuits. Memory is retained, and refreshes continue. All clocks stop except RTC clock.
G1/S4:Suspend to Disk ----The context of the system is maintained on the disk. All power is then shut off to the system except for the logic required to resume.
G2/S5:Soft off ----System context is not maintained. All power is shut off except for the logic required to restart. A full boot is required when waking.
G3:Mechanical off ----Power failure Because the system does not have any power.
Power Sequence Types on Notebook
Power Sequence Types on Notebook
Five types of power sequence G3S5 S5S0 (Power on) S0S5 (Power down) S3S0 S0S3
Power on---AC/DC Block FlowPower on---AC/DC Block Flow
AC_IN#
PM_PWRBTN# -> 1Delay 20ms
PM_RSMRST# -> 1
end
VSUS_ON
end
VSUS_ON -> 0
PM_RSMRST# -> 0
end
0 1
0 1
START
Wait VSUS_GD=1
VSUS_ON -> 1Delay 5ms
0
1
Difference:AC mode (plug in adaptor): G3S4/S5 ,
have VSUS power. (to save power)
DC mode (only plug in battery): G3S4/S5 ,
have no VSUS power.
Power on---AC SequencePower on---AC Sequence
PCHPCHPCHPCH1.RTCRST#
ECECITE8570ITE8570
ECECITE8570ITE8570
MB39A132MB39A132MB39A132MB39A1322.A/D_DOCK_IN
3.AC
_BA
T_S
YS
RT8206AGRT8206AGQWQW
RT8206AGRT8206AGQWQW
4.+3VA
5.VSUS_ON6.+3VSUS/+5VSUS
7.VSUS_GD
9.PWR_SW#
8.P
M_R
SM
RS
T#
10.P
WR
BT
N#
11.P
M_S
US
C#
12.P
M_S
US
B#
13.SUSC_ON
14.SUSB_ONMEMORY POWER(+1.8V,0.9V)MEMORY POWER(+1.8V,0.9V)
MEMORY POWER(+1.8V,0.9V)MEMORY POWER(+1.8V,0.9V)
OTHER MAIN POWER(+1.5V,+1.05V etc.)OTHER MAIN POWER(+1.5V,+1.05V etc.)OTHER MAIN POWER(+1.5V,+1.05V etc.)OTHER MAIN POWER(+1.5V,+1.05V etc.)
15.CPU_VRON (110ms)
16.VRM_PWRGDVcore Vcore ControllerController
Vcore Vcore ControllerController
16.VRM_PWRGD
17.PM
_PW
RO
K
CPUCPUCPUCPU
4.AC_OK=1
RTCRTCBATBAT
RTCRTCBATBAT
18.H
_CP
UP
WR
GD
19.P
LT
_RS
T#
20.H
_CP
U_R
ST
#
Power on---DC SequencePower on---DC Sequence
PCHPCHPCHPCH1.RTCRST#
ECECITE8570ITE8570
ECECITE8570ITE8570
MB39A132MB39A132MB39A132MB39A1322.BAT_CON
3.AC
_BA
T_S
YS
RT8206AGRT8206AGQWQW
RT8206AGRT8206AGQWQW
4.+3VA
6.VSUS_ON7.+3VSUS/+5VSUS
8.VSUS_GD
5.PWR_SW#
9.P
M_R
SM
RS
T#
10.P
WR
BT
N#
11.P
M_S
US
C#
12.P
M_S
US
B#
13.SUSC_ON
14.SUSB_ONMEMORY POWER(+1.8V,0.9V)MEMORY POWER(+1.8V,0.9V)
MEMORY POWER(+1.8V,0.9V)MEMORY POWER(+1.8V,0.9V)
OTHER MAIN POWER(+1.5V,+1.05V etc.)OTHER MAIN POWER(+1.5V,+1.05V etc.)OTHER MAIN POWER(+1.5V,+1.05V etc.)OTHER MAIN POWER(+1.5V,+1.05V etc.)
15.CPU_VRON (110ms)
16.VRM_PWRGDVcore Vcore ControllerController
Vcore Vcore ControllerController
16.VRM_PWRGD
17.PM
_PW
RO
K
CPUCPUCPUCPU
4.AC_OK=1
RTCRTCBATBAT
RTCRTCBATBAT
18.H
_CP
UP
WR
GD
19.P
LT
_RS
T#
20.H
_CP
U_R
ST
#
N71Ja Power on Sequence(1)N71Ja Power on Sequence(1)
N71Ja Power on Sequence(2)N71Ja Power on Sequence(2)
N71Ja Power on Sequence(3)N71Ja Power on Sequence(3)
N71Ja Power on Sequence(4)N71Ja Power on Sequence(4)
N71Ja Power on Sequence(5)N71Ja Power on Sequence(5)
Power Down---General Sequence
Power Down---General Sequence
Power Down---General Sequence
Power Down---General Sequence
Power down---General Sequence
Common BugsCommon Bugs
1.The system can not be powered on, and the adaptor LED indication flicker. Here is somewhere short, check all power rails whether have been short to GND.
2.The system can not be powered on, and power LED not lighten. Maybe The BIOS ROM content has been wrecked. +3VA powered? Why not VSUS power? Power IC or MOSFET or Diode burnout?
3.The power LED lighten, but the system can not bring up to DOS. plug in debug card, view the 80 post code, for example: 80 code no motion, show 00 –> CPU not work –>measure power sequence black screen, show d0~d5 –> memory plug failed or memory broken black screen, show F0~F2 –> one DIMM slot failed show 38 –> check USB port and USB device If not mount LPC debug & New card debug card because of cost down, try to flash BIOS by
JIG board or measure sequence.4.The system often show blue screen suddenly in OS
un-install drives (even enter safe mode), find whether a device driver installed wrongly cause it un-plug device to check BIOS updated? Care for BIOS release note check FAN status/thermal module –> over temperature? and so on……
RMA Training RequestRMA Training RequestHow to judging the CPU’s function when it on board?
Debug Card -> Reset -> Power, CLK ->Visual Inspection (Impurities, PIN Broken, curving, Error Component )
Do not boot up, How to do?
Check Debug code
Debug code:00 -> Reset , Power, CLK , Visual Inspection.
Debug code: OK -> GPU, CRT/LVDS
The Voltage and CLK is OK, but no display. How to do?
Remove all Device, Check DIMM, Flash EEPROM, Reset COMST, Check all reset nets, Check Debug code.
Blue screen, Hung up, How to do?
Remove all Device, Check DIMM, Flash EEPROM, Change HDD , Check FAN & Thermal Module, Check Windows error code.
The Difference with EC Chip ITE8510 、 8511 、 8752 、 8512 、 8502 、 8570.
ITE8510 、 8511 -> SantaRosa platform -> ISA ROM
ITE8752 、 8512 -> Montevina platform -> SPI ROM
ITE8570 -> Calpella platform -> SPI ROM
THE ENDTHANKS