Post on 30-Apr-2018
INSTRUCTION MANUAL
CM16 Carbine BLK/DSTCM16 Raider BLK/DST
Automatic firingSingle shot
1.Push the butt plate lock ( both sides ) 2.Pull out the butt plate.
1.Charge up the battery. 2.Charging will be completed after 3 hours.
Take off the cover. Pull out the wire connector.
Connect battery plug with the connector.1.Pull the slip ring and hold.2.Disassemble the lower handguard.
1.Pull the slip ring and hold.2.Reinstall the lower handguard.
Finish.
Connect battery plug with the connector until you heard a click sound.
Insert the battery into stock. Reinstall the battery cover and butt plate.
Please select quality battery with the CE approval, to avoid any unnecessary damage on the product.Please use either 8.4V or 9.6V battery, if different voltage used, it might damage the product.Remove the battery from the product when it is not in use.Do not wet nor incinerate the battery, nor to deform the terminal.
1.
2.
3.4.
Do not catch your fingers in the dummy bolt.Never hold the gun sideways as the BB pellets will curve right or left.
It is strongly recommended the use of G&G BB pellets only. Using low quality BB pellets will shorten product life span and void product warranty.
Safety On Semi Auto Full AutoThe trigger cannot be pulled
Front sight
Rail system
Detachable rear sight
Extend battery stock
Stock release lever
Reinforced Grip
TriggerSelector lever
Flash suppressor
Outer barrel
Hi-cap 450R magazine
Slip ring
G-11-056NI-MH 9.6V 1600 mAh
Detachable carrying handle Charging handle
6-PositionRetractable stock
Open the cover of magazine. Load G&G 5.95mm BB pellets into the magazine.
Close the cover plate then turn the gear until the sound changes.
Insert the magazine until you heard a click sound.
COMPONENTS
FIRING MODE & SAFETY
BATTERY SETTING
SETTING MAGAZINE
HOP-UP ADJUSTMENT
CM16 RAIDERBATTERYSETTING
CM16 CARBINEBATTERYSETTING
Best Position.
Too much Hop-up.( Turn the adjust lever toward Normal )
Not enough Hop-up. ( Turn the adjust lever toward Hop )or Too much Hop-up. ( Turn the adjust lever toward Normal )
Click
Click
Click
Turn to Normal Turn to Hop
Handguard
RECOMMENDEDBATTERY TYPE
42
3
1
CM16 Raider- 01CM16 Raider- 02CM16 Raider- 03CM16 Raider- 04CM16 Raider- 05CM16 Raider- 07CM16 Raider- 08CM16 Raider- 09CM16 Raider- 10CM16 Raider- 11CM16 Raider- 12CM16 Raider- 13CM16 Raider- 14CM16 Raider- 15CM16 Raider- 16
CM16 Raider- 17CM16 Raider- 18CM16 Raider- 19CM16 Raider- 20CM16 Raider- 21CM16 Raider- 22CM16 Raider- 23CM16 Raider- 24CM16 Raider- 25CM16 Raider- 26CM16 Raider- 27CM16 Raider- 28CM16 Raider- 29CM16 Raider- 30CM16 Raider- 31
Flash suppressor setRail system setRear sight base setRear sight setFront barrel / Front sight set Barrel base setPiston rodAssist knob setInner barrelUpper receiver setCharging handle setHop-up setPort cover setFront frame lock pin setBolt catch set
Magazine catch setSelector lever setStock washerEnhanced rod setHi-cap 450R magazineLower receiver setTrigger guard setSelector plateRear frame lock pin setGripMotor setGrip bottom setExtended stock setRear wire setGear box set
CM16 Carbine- 06CM16 Carbine- 32CM16 Carbine- 33
CM16 Carbine- 34CM16 Carbine- 35CM16 Carbine- 36
Slip ring setCarrying handle setRear outer barrel set
Front outer barrel setHandguard setRetractable stock set
For CM16 Raider / CM16 Carbine
For CM16 Carbine
1
2
1
2
1
2
3
1
2
2
3
4
1
2
3
1
2
12
1
2
3
1
23
4
5
6
78
910
1112
13
14
15
16
1
2
2
3
3
4
4
5
5
6
6
1
2
2
3
4
56
1
7
1
2
3
456
7
7
8 89
10
3
31
1
2
3
4
5
67
1
1
2
3
5
1
1
2 3
2
23
3
4
1
2
1
2 3
4
1
23
12
34
5
11 123
4
5
6
78
910
12131415
16
CM16 Raider- 01
CM16 Raider- 02
CM16 Raider- 03
CM16 Raider- 11
CM16 Raider- 16
CM16 Raider- 22
CM16 Raider- 29 CM16 Raider- 30
CM16 Raider- 17
CM16 Raider- 18
CM16 Raider- 19
CM16 Raider- 05
CM16 Raider- 08
CM16 Carbine- 06
CM16 Raider- 04
CM16 Raider- 07
CM16 Raider- 09
CM16 Raider- 12
CM16 Raider- 20
CM16 Raider- 10
CM16 Raider- 13
CM16 Raider- 14
CM16 Raider- 15
CM16 Raider- 23
CM16 Raider- 24
CM16 Raider- 25
CM16 Raider- 26
CM16 Raider- 27
CM16 Raider- 28
CM16 Raider- 21
12
3
4
5
1
1
2
2
2
34
5
CM16 Carbine- 33
CM16 Carbine- 36
CM16 Carbine- 34
CM16 Carbine- 35
► You may purchase all of the groups’ parts from G&G support Dep.
► E-Mail: support@guay2com
ADDRESS
WEBSITETEL
FAX
Changhua / No. 999, Zhonghua Rd., Shengang Township, (Head Quarter) Changhua County 50952, TaiwanTaipei / 11F-3, NO.27, Lane 169, Kangning St, Shijr City, Taipei County 22180,TAIWAN
Sales Department / sales@guay2.com b2b@guay2.com
Technology support Department / support@guay2.com
www.GUAY2.com
Changhua / 886-4-798-9000Taipei / 886-2-2692-2000
Changhua / 886-4-798-9900Taipei / 886-2-2692-4000
G2-201309-01-英
INSTRUCTION MANUAL
CM16 Carbine- 31
CM16 Carbine- 32
Keep the selector on Safe modeuntil you are actually ready to shoot.
Special ShootingUsed for precision firing.
Common ShootingUsed for full automatic firing.
Windage knob (left / right adjustment)Elevation knob (up / down adjustment)
WindageWindage
ElevationElevation
REAR SIGHT ADJUSTMENT MAINTENANCE
TROUBLE SHOOTINGPARTS LIST
RETRACTABLESTOCK
CM16 Raider
Press the stock release lever to unlock. Adjust the position ( 6 position ).
Press the stock release lever to unlock. Adjust the position ( 6 position ).
MOVABLEPARTS
RETRACTABLESTOCK
CM16 Carbine
MOVABLEPARTS
Detachable rear sight. Turn the knobs counterclockwise to disassemble the rear sight.
Take off the rear sight to install other accessories.
Turn the knobs counterclockwise.
Detachable the carrying handle Dot sight (Optional)
Take off carrying handle. You can buy other accessories to installon the rail system.
Remove the magazine. Return the hop up dial to normal position and insert the cleaning rod from the lead edge of the inner barrel.
Be aware to have the rod facing down and reaching to the end, and remove clogged pellets.
The screw at bottom of the grip. Please use the screwdriver to adjust.
Check the wire set contact with motor. Check the battery and connector.
Adjust screw when the gear noise becomes shrilly.
No operation No operation
CM16 Carbine BLK/DSTCM16 Raider BLK/DSTCM16 Carbine BLK/DSTCM16 Raider BLK/DST