Post on 30-Jun-2018
Digital Video Camcorder
Instruction Manual English
Mini DigitalVideoCassette
PAL
This instruction manual covers the MV650i, MV630i, MV600i and MV600. Please notethat illustrations and explanation in this manual are based on the MV650i.
PUB.DIE-181
Introduction
Mastering the Basics
Using the Full Range of Features
Editing
Using a Memory Card
MV630iMV650i
AdditionalInformation
0_D73PAL_E(cover) 02.12.26 9:17 PM Page 1
2
Intr
od
uct
ion
E
Important Usage Instructions
WARNING:TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (ORBACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TOQUALIFIED SERVICE PERSONNEL.
WARNING:TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THISPRODUCT TO RAIN OR MOISTURE.
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK AND TO REDUCE ANNOYINGINTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY.
CAUTION:DISCONNECT THE MAINS PLUG FROM THE SUPPLY SOCKET WHEN NOT IN USE.
• Use of CV-150F/CV-250F DV cable is necessary to comply with the technical requirementof EMC Directive.
CA-570 identification plate is located on the bottom.
1_D73PAL_E(02-12) 02.12.26 9:20 PM Page 2
3
Intro
du
ction
E
Reference GuideThe following manuals are supplied with the camcorder:
❍ Digital Video Camcorder MV650i/MV630i/MV600i/MV600 Instruction Manual
This manual explains the camcorder operations from basic video recording to the
use of the full range of features.
❍ Windows XP Users Only
DV NETWORK SOLUTION DISK Software Instruction Manual
This manual explains how to download/upload images from/to the memory card
using a DV (IEEE1394) cable. You can also perform videoconference and file transfer
over the Internet using the provided software. Available functions depend upon
the camcorder model and networking environment.
❍
DIGITAL VIDEO SOLUTION DISK Software Instruction Manual
This manual explains how to download images from the memory card to a
computer using the supplied USB cable. You can add sample images for Card Mix
and My Camera settings from the supplied DIGITAL VIDEO SOLUTION DISK.
Trademark Acknowledgements• Canon is a registered trademark of Canon Inc.
•D is a trademark.
• logo is a trademark.
• Macintosh is a trademark of Apple Computer Inc., registered in the United States
and other countries.
• Windows® is either a registered trademark or trademark of Microsoft Corporation in
the United States and/or other countries.
• Other names and products not mentioned above may be registered trademarks or
trademarks of their respective companies.
MV630iMV650i
1_D73PAL_E(02-12) 02.12.26 9:20 PM Page 3
4
Intr
od
uct
ion
E
Table of ContentsIntroduction
Reference Guide..............................................................................................................3Thank You for Choosing a Canon ................................................................................7Introducing the MV650i/MV630i/MV600i/MV600 ......................................................8Components Guide ........................................................................................................9
Mastering the Basics
PreparationsUsing a Household Power Source ..............................................................................13Attaching and Charging the Battery Pack ................................................................14Installing the Backup Battery ......................................................................................17Preparing the Camcorder ............................................................................................18Loading a Cassette ........................................................................................................20Using the Wireless Controller......................................................................................22Setting the Time Zone, Date and Time......................................................................23
Basic RecordingRecording Movies on a Tape ......................................................................................26Zooming ........................................................................................................................28Using the LCD Screen....................................................................................................30Searching and Reviewing when Recording ..............................................................33Tips for Making Better Videos ....................................................................................34
Basic PlaybackPlaying Back a Tape ......................................................................................................35Playing Back on a TV Screen........................................................................................39
Using the Full Range of Features
GeneralMenus and Settings ......................................................................................................43Changing the Remote Sensor Mode..........................................................................48Customizing the Camcorder........................................................................................49
Setting the Light-up Buttons ........................................................................50Other Camcorder Settings ..........................................................................................51
RecordingChanging the Recording Mode (SP/LP) ......................................................................53Recording Still Images on a Tape................................................................................54Using the Recording Programs....................................................................................56Using Digital Effects......................................................................................................60Using the Multi-Image Screen ....................................................................................66Turning Off the Image Stabilizer ................................................................................68Recording With the Self-Timer....................................................................................69Audio Recording ..........................................................................................................70
Using the VL-3 Video Light (Optional) ........................................................72Using the DM-50 Microphone (Optional)....................................................73
Manual AdjustmentsAdjusting the Focus Manually ....................................................................................74
MV650i
MV650i
MV650i
1_D73PAL_E(02-12) 02.12.26 9:20 PM Page 4
5
Intro
du
ction
Adjusting the AE Shift ..................................................................................................76Setting the Shutter Speed............................................................................................77Setting the White Balance ..........................................................................................79
PlaybackMagnifying the Image..................................................................................................81Displaying the Data Code ............................................................................................82Photo Search/Date Search............................................................................................84Returning to a Pre-marked Position ..........................................................................85
EditingRecording to a VCR or Digital Video Device ............................................................86
Recording from Analog Video Devices (VCR, TV or Camcorder)............................................................................................88
Recording from Digital Video Devices (DV Dubbing) ......89Converting Analog Signals into Digital Signals
(Analog-Digital Converter) ......................................................................................91Replacing Existing Scenes (AV Insert) ................................93
Audio Dubbing..............................................................................................................95Connecting to a Computer Using a DV (IEEE1394) Cable ......................................98
Using a Memory CardInserting and Removing the Memory Card ..............................................................99Selecting the Image Quality/Size ..............................................................................100Recording Still Images on a Memory Card..............................................................103Recording Panoramic Images (Stitch Assist Mode) ................................................106
Recording Motion JPEG Movies on a Memory Card................................108Playing Back a Memory Card ....................................................................................110Protecting Images ......................................................................................................113Erasing Images ............................................................................................................114Selecting Still Images for Printing (Print Order) ....................................................115Printing with the Direct Print Function....................................................................117Combining Images (Card Mix) ..................................................................................121Copying Still Images....................................................................................................125Formatting a Memory Card ......................................................................................127Connecting to a Computer Using a USB Cable ......................................................128Creating a Start-up Image ........................................................................................129Memory Card Information ........................................................................................130
Additional InformationScreen Displays ............................................................................................................133List of Messages ..........................................................................................................137Maintenance................................................................................................................140Troubleshooting ..........................................................................................................144System Diagram ..........................................................................................................147Optional Accessories ..................................................................................................148Specifications ..............................................................................................................151Index ............................................................................................................................153
MV650i
MV630iMV650i
MV600iMV630iMV650i
MV600iMV630iMV650i
MV600iMV630iMV650i
MV600iMV630iMV650i
E
1_D73PAL_E(02-12) 02.12.26 9:20 PM Page 5
6
Intr
od
uct
ion
Conventions Used in This Manual
Operating Modes
: MV650i and MV630i only.
Available functions depend upon the operating mode. It is indicated as follows:
: Function can be used in this mode.
: Function cannot be used in this mode.
Other Symbols and References
❍ : Reference page number.
❍ : Functions to be operated on the body of the camcorder.
❍ : Functions to be operated on the wireless controller.
❍ : Additional topics that complement the basic operating procedures.
❍ : Precautions related to the camcorder operation.
❍ Capital letters are used to refer to buttons on the camcorder or the wireless
controller.
❍ [ ] are used to refer to menu items displayed on the screen.
❍ “Screen” refers to the LCD and the viewfinder.
CAMERA
CAMERA
Shaded area
EOperating Mode
Position of the POWER Switch
Position of the TAPE/CARD Switch
CAMERA CAMERA TAPE
PLAY (VCR) PLAY (VCR) TAPE
CARD CAMERA CAMERA CARD
CARD PLAY (VCR) PLAY (VCR) CARD
1_D73PAL_E(02-12) 02.12.26 9:20 PM Page 6
7
Intro
du
ction
E
Thank You for Choosing a CanonThe Canon MV650i/MV630i/MV600i/MV600 provides a full range of options and
functions. We recommend reading this manual thoroughly before you use the
camcorder. It will help you to become more familiar with your camcorder, and learn
how to operate it properly.
We suggest that you master the basic operations of the camcorder first, before
moving on to its full range of features.
Checking Supplied Accessories
WL-D79 Wireless Controller,
WL-D80 Wireless ControllerMV600MV600i
MV630iMV650i Two AA Batteries Lens Cap and LensCap Cord
SS-800 Shoulder Strap
WA-30.5Wide AttachmentMV650i
BP-512 Battery Pack,
BP-508 Battery PackMV600MV600iMV630i
MV650i CA-570 CompactPower Adapter (incl.power cord)
Lithium ButtonBattery CR1616
STV-250N StereoVideo Cable IFC-300PCU USB Cable
MV630iMV650iSDC-8M SD MemoryCard (containingsample images)
MV630iMV650i
HardCase for SD MemoryCard
MV630iMV650i DV NETWORKSOLUTION DISK
DIGITAL VIDEOSOLUTION DISK
MV630iMV650i
PC-A10 SCARTAdapter (Europe, Asia)
1_D73PAL_E(02-12) 02.12.26 9:20 PM Page 7
8
Intr
od
uct
ion
E
Introducing the MV650i/MV630i/MV600i/MV600
Stabilises your recordings even in long
telephoto shots (in CAMERA mode).
Allows recording even in dark places.
The Night mode adjusts automatically to
the optimum shutter speed.
With the MV650i’s Super Night mode (in
CAMERA mode) and Low Light Plus
mode (in CARD CAMERA mode), you can
keep on shooting without turning the
lights on. The assist lamp (White LED)
lights up to illuminate the subject.
Just press the photo button to capture
still images like photographs.
You can personalise your camcorder by
customizing the start-up image and
camcorder sounds.
Simply slide Canon’s DM-50 DirectionalStereo Microphone or VL-3 Video Lightinto the accessory shoe; the camcorderwill automatically provide power andconnections.
Show your creativity by using the specialeffects and faders. The multi-imagescreen captures moving subjects in 4, 9 or16 sequences of still images.
You can record images on a SD MemoryCard or MultiMediaCard. Imagesrecorded in Stitch Assist mode can bemerged into one panoramic scene withthe supplied software.
You can print still images by connectingto a Canon Bubble Jet Printer with DirectPrint function.
Allows transfer of memory card data to acomputer with built-in USB port. You canorganise and edit images on yourcomputer using the supplied software.
The DV terminal allows high-qualitytransfer with virtually no deterioration inquality of images. You can edit imagesby connecting the camcorder to a PCwith IEEE1394 terminal. Windows XPUsers can use the supplied software toperform videoconference and filetransfer over the Internet.
22× Optical and 440× Digital Zoom (MV650i)
Advanced Accessory Shoe(MV650i)
20× Optical and 400× Digital Zoom (MV630i)
18× Optical and 360× Digital Zoom (MV600i/MV600)
Super Night Mode and Low LightPlus Mode (MV650i)
Image StabilizerDigital Effects
Memory Card (MV650i/MV630i)
Direct Print (MV650i/MV630i)
USB Terminal (MV650i/MV630i)
IEEE1394 DV Terminal
Night Mode
Still Images
My Camera Settings
Analog Line-in Recording/AV Insert Editing(MV650i/MV630i/MV600i), Audio Dubbing
1_D73PAL_E(02-12) 02.12.26 9:20 PM Page 8
9
Intro
du
ction
E
Components Guide
MV650i/MV630i/MV600i/MV600
P
123456789
DATACODE
MIX/SLIDESHOW
DIGITALEFFECTS ON/OFF
REC (record) SEARCH – button (p. 33) / Record review button (p. 33) / (rewind) button (p. 35) / CARD – button* (p. 110)
REC SEARCH + button (p. 33) / (fast forward) button (p. 35) /CARD + button* (p. 110)
FOCUS button (p. 74) / (play/pause) button (p. 35)
AE SHIFT button (p. 76) / (stop) button (p. 35) / (index screen) button* (p. 111)
P
LCD panel OPEN button (p. 30)
BATT. (battery release) button (p. 14)
Memory card slot* (p. 99)
Backup battery cover (p. 17)
Battery attachment unit (p. 14)
Serial number
Selector dial (p. 38, 43)
Card access indicator* (p. 103) /CHARGE indicator (p. 14)
LCD screen (p. 30)
Card MIX button* (p. 123) /SLIDE SHOW button* (p. 111)/ (stitch assist) button*(p. 106)
(self-timer) button (p. 69) / DATA CODE button (p. 82)
Program selector (p. 56)
DIGITAL EFFECTS button (p. 60)
Digital effects ON/OFF button (p. 60)
MENU button (p. 43)
Program AE
Easy recording
DC IN terminal (p. 13)
and only.* MV650i MV630i
1_D73PAL_E(02-12) 02.12.26 9:20 PM Page 9
10
Intr
od
uct
ion
E
TAPE
CARD
OFF
(VCR)PLAYPLAY
CAMERACAMERA
POWERPOWERCAMERA
OFF
PLAY(VCR)}
Diopter adjustment lever (p. 18)
Viewfinder protect cover (p. 141)
PHOTO button (p. 54, 103)
Advanced accessory shoe (p. 72)
Accessory shoe (p. 149)
Zoom lever (p. 28)
Built-in speaker (p. 37)
TAPE/CARD switch* (p. 6)
Grip belt (p. 18)
Strap mount (p. 19)
Cassette compartment cover (p. 20)
Cassette compartment (p. 20)
Viewfinder (p. 18)
Strap mount (p. 19)
Start/stop button (p. 26)
POWER switch (p. 6)
and only.* MV650i
MV650i
MV630i MV600i MV600
MV630i
1_D73PAL_E(02-12) 02.12.26 9:20 PM Page 10
11
Intro
du
ction
E
S DV
AV
MIC
Bottom view
Terminal cover
Assist lamp (White LED) (p. 58)
Remote sensor (p. 22)
Stereo microphone (p. 70)
S-video IN/OUT terminal *2 (p. 40)
DV IN/OUT terminal *2
(p. 86)
Terminal cover
OPEN/EJECT switch (p. 20)
Tripod socket (p. 34)
USB terminal *1 (p. 128)
AV IN/OUT terminal *2 (p. 39) / (phones) terminal (p. 37)
MIC terminal (p. 70)
and only.*1
Output only.*2MV650i
MV600
MV650i
MV630i
1_D73PAL_E(02-12) 02.12.26 9:20 PM Page 11
12
Intr
od
uct
ion
E
WIRELESS CONTROLLER WL-D80
W T
WIRELESS CONTROLLER WL-D79
START/STOP PHOTO
ZOOM
SELF T.SELF T.
D.EFFECT.
ON/OFF
PHOTO
D.EFFECT.
ON/OFFSET
MENU
W TZOOM
SET
MENU
TV SCREENTV SCREEN
REW
PAUSE
AV INSERT AV DV REMOTE SET
SLOW 2
PLAY
STOP
FFZERO SETMEMORY
RECPAUSE
12bitAUDIO OUT
SEARCH SELECT
REW
PAUSE
AV INSERT AV DV REMOTE SET
SLOW 2
PLAY
STOP
FF
SEARCH SELECT
DATA CODE
AUDIO DUB.
ZERO SETMEMORY
RECPAUSE
12bitAUDIO OUT
DATA CODE
AUDIO DUB.
INDEX SLIDE SHOW CARD
START/STOP
PHOTO button (p. 54, 103)
D. EFFECTS (Digital effects) button (p. 60)
START/STOP button (p. 26)
SELF T. button (p. 69)
TV SCREEN button (p. 133)
DATA CODE button (p. 82)
SEARCH SELECT button (p. 84)
ZERO SET MEMORY button (p. 85)
12bit AUDIO OUT button (p. 97)
AUDIO DUB. button (p. 96)
REC PAUSE button *2 (p. 88)
REW button (p. 35)
AV INSERT button *2 (p. 94)
Digital effects ON/OFF button (p. 60)
Transmitter
Zoom buttons (p. 28)
Controller buttons (p. 43)
MENU button (p. 43)
SET button (p. 43)
Search buttons (p. 84)
PLAY button (p. 35)
FF button (p. 35)
button (p. 36)
STOP button (p. 35)
2 button (p. 36)
REMOTE SET button (p. 48)
SLOW button (p. 36)
AV DV button *2 (p. 92)
button (p. 36)
PAUSE button (p. 36)
INDEX button *1 (p. 111)
SLIDE SHOW button *1 (p. 111)
CARD buttons *1 (p. 110)
!5
!6
!8
q
r
t
y
!1
!1
i
#3
!0
o !0
o
!3 !3
@6
e !7
!9
!5
!6
!8
!7
!9
@2
@0@0
@3
@9
@4
@7
@8
@5@6
@7
@5
#0
@9
@8
#0
!2 !2
!4 !4w
q
r
t
e
w
u
y
i
u
@1@2
@3
@4
@1#2
#1
qwertyuio!0!1!2!3!4!5!6!7
!8!9@0@1@2@3@4@5@6@7@8@9#0#1#2#3
and only.*1
*2 Not available with the .
MV650i MV630i
MV600
WL-D79 WL-D80MV650i MV600iMV630i MV600
Wireless Controller
1_D73PAL_E(02-12) 02.12.26 9:20 PM Page 12
13
Masterin
g
the B
asics
E
Using a Household Power SourceYou can operate the camcorder from a household power source using the supplied
power adapter. The power adapter converts current from a power outlet (100-240 V
AC, 50/60 Hz) to the DC current used by the camcorder.
1. Turn the POWER switch to OFF.
2. Connect the power cord to thepower adapter.
3. Plug the power cord into a poweroutlet.
4. Connect the power adapter to thecamcorder’s DC IN terminal.
5. After use, disconnect the power adapter from the camcorder. Unplugthe power cord from the power outlet and disconnect it from theadapter.
❍ Turn off the camcorder before connecting or disconnecting the power adapter.❍ If the adapter is used close to a TV, it may cause picture interference. Move the
adapter away from the TV or the antenna cable. ❍ Do not connect any products that are not expressly recommended to the
camcorder’s DC IN terminal or to the power adapter.❍ You may hear some noise from the power adapter during use. This is not a
malfunction.
e
q
w
rr
OFFOFF
(VCR)(VCR)PLAY
CAMERACAMERA
POWERPOWER
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 13
14
Mas
teri
ng
th
e B
asic
s
E
Attaching and Charging the Battery PackCharge the battery pack with the supplied power adapter before you use the
camcorder for the first time and subsequently when the message “CHANGE THE
BATTERY PACK” appears.
1. Turn the POWER switch to OFF.
2. Move the viewfinder upward.
3. Attach the battery pack to thecamcorder.
• Remove the terminal cover of the battery
pack.
• Align the end of the battery pack with the
line on the camcorder, press lightly and slide
it in the direction of the arrow until it clicks.
4. Connect the power cord to theadapter.
5. Plug the power cord into a poweroutlet.
6. Connect the power adapter to thecamcorder’s DC IN terminal.
7. When charging is complete,disconnect the power adapter fromthe camcorder. Unplug the powercord from the power outlet anddisconnect it from the adapter.
8. Remove the battery pack after use.
Press the BATT. button to remove the battery.
❍ The battery pack may be defective when the CHARGE indicator flashes rapidly.❍ The CHARGE indicator informs you about the charge status.
0-50%: Flashes once every secondMore than 50%: Flashes twice every second100%: Glows steadily
❍ Do not disconnect and reconnect the power cord while charging a batterypack. The battery pack may not be charged correctly even if the CHARGEindicator glows steady. The battery pack may also not be charged correctlywhen a power outage occurs during charging. Remove the battery pack andattach it back to the camcorder.
q
e
w
OFF
(VCR)PLAY
CAMERACAMERA
POWERPOWER
y
t
r
DC IN 8.4V
CARD/CHARGE
click
CHARGE indicator
DC IN terminal
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 14
15
Masterin
g
the B
asicsCharging, Recording and Playback TimeBelow times are approximate and vary according to the charging, recording or
playback conditions.
Charging Time
• Charge the battery pack in temperatures between 5º C and 40º C.• A lithium ion battery pack can be charged at any charge state. Unlike conventional
battery packs, you do not need to completely use or discharge it before charging.
Recording Time
* Approximate times for recording with repeated operations such as start/stop, zooming,power on/off. Actual time may be shorter.
• We recommend that you prepare battery packs 2 to 3 times longer than you think youmight need.
• To conserve battery charge, turn off the camcorder instead of leaving it in record pausemode.
Playback Time
E
Battery Pack Charging Time
BP-508 (MV630i/MV600i/MV600) 110 min.
BP-512 (MV650i/optional) 120 min.
BP-511 (Optional) 120 min.
BP-522 (Optional) 210 min.
BP-535 (Optional) 310 min.
Battery Pack Maximum Recording Time Typical Recording Time*
Using the Viewfinder Using the LCD Using the Viewfinder Using the LCD
BP-508 100 min. 75 min. 55 min. 40 min.(MV630i/MV600i/MV600)
BP-512 180 min. 140 min. 95 min. 75 min.(MV650i/Optional)
BP-511 (Optional) 180 min. 140 min. 95 min. 75 min.
BP-522 (Optional) 370 min. 295 min. 195 min. 155 min.
BP-535 (Optional) 590 min. 470 min. 315 min. 250 min.
Battery Pack Playback Time
Using the LCD
BP-508 (MV630i/MV600i/MV600) 70 min.
BP-512 (MV650i/optional) 125 min.
BP-511 (Optional) 125 min.
BP-522 (Optional) 250 min.
BP-535 (Optional) 400 min.
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 15
How much power is left?The battery symbols indicate the charge status of the battery
pack.
When the battery pack is empty, “CHANGE THE BATTERY PACK”
appears for 4 seconds and starts flashing.
The battery charge indicators are not constant – they vary
according to the condition under which battery pack and
camcorder are used.
Battery Pack Handling Precautions
DANGER!
Treat the battery pack with care.
• Keep it away from fire (or it might explode).
• Do not expose the battery pack to temperature higher than 60º C. Do not leave
it near a heater or inside a car in hot weather.
• Do not try to disassemble or modify it.
• Do not drop or knock it.
• Do not get it wet.
❍ Charged battery packs continue to discharge naturally. Therefore, charge them onthe day of use, or the day before, to ensure a full charge.
❍ Attach the terminal cover whenever a battery pack is not in use. Contact to metallicobjects may cause a short circuit and damage the battery pack.
❍ Dirty terminals may cause a poor contact between the battery pack and thecamcorder. Wipe the terminals with a soft cloth.
❍ Since storing a charged battery pack for a long time (about 1 year) can shorten itslifecycle or affect performance, we recommend to discharge the battery pack fullyand to store it in a dry place at temperatures no higher than 30˚ C. If you do notuse the battery pack for long periods, charge and discharge it fully at least once ayear. If you have more than 1 battery pack, perform these precautions at the sametime for all battery packs.
❍ Although the battery pack’s operating temperature range is from 0˚ C to 40˚ C, theoptimal range is from 10˚ C to 30˚ C. At cold temperatures, performance willtemporarily decline. Warm it in your pocket before use.
❍ Replace the battery pack if the usable time after full charge diminishes substantiallyat normal temperatures.
16
Mas
teri
ng
th
e B
asic
s
E
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 16
17
Masterin
g
the B
asics
E
Installing the Backup BatteryThe backup battery allows the camcorder to retain date, time and other camcorder
settings while the power source is disconnected. Power the camcorder from a
household power source or with a battery pack when replacing the backup battery.
1. Open the backup battery cover.
2. Insert the lithium battery with the + side facing outward.
3. Close the cover.
WARNING!
• The battery used in this device may present a fire or chemical burn hazard if
mistreated. Do not recharge, disassemble, heat above 100° C or incinerate the
battery.
• Replace the battery with a CR1616 made by Panasonic, Hitachi Maxell, Sony, Toshiba,
Varta or Renata. Use of other batteries may present a risk of fire or explosion.
• The used battery should be returned to the supplier for safe disposal.
❍ Do not pick up the battery using tweezers or other metal tools as this willcause a short circuit.
❍ Wipe the battery with a clean dry cloth to ensure proper contact.❍ Keep the battery out of reach of children. If it is swallowed, seek medical
assistance immediately. The battery case may break and the battery fluids maydamage stomach and intestines.
❍ Do not disassemble, heat or immerse the battery in water, to avoid the risk ofexplosion.
The backup battery has a life span of about a year. j flashes to inform you thatit needs to be replaced.
q w e
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 17
18
Mas
teri
ng
th
e B
asic
s
E
Preparing the Camcorder
Adjusting the Viewfinder (Diopter Adjustment)1. Turn on the camcorder and keep the
LCD panel closed to adjust theviewfinder.
2. Adjust the diopter adjustment lever.
Do not leave the viewfinder exposed to direct sunlight as it may melt (due toconcentration of light by the lens). Adjust the angle of the viewfinder to preventsunlight from entering.
Attaching the Lens Cap1. Attach the cord to the lens cap.
2. Pass the grip belt through the loopon the cord.
Press the buttons on the lens cap when
attaching/removing it. Hook the lens cap on
the grip belt while you are recording, and
place it over the lens when you have finished.
Fastening the Grip BeltHold the camcorder with your righthand and adjust the belt with your left.
Adjust the grip belt so that you can reach the
zoom lever and photo button with your index
finger, and the start/stop button with your
thumb.
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 18
19
Masterin
g
the B
asics
E
Attaching the Shoulder StrapFor extra security and portability, attach the shoulder strap before using the
camcorder.
Pass the ends through the strap mountand adjust the length of the strap.
Mounting the Wide AttachmentThe WA-30.5 Wide Attachment gives you a wide perspective for indoor shots or
panoramic views (0.6×). The wide attachment is for use at maximum wide-angle.
Screw the wide attachment fully intothe lens filter thread.
❍ If you zoom to telephoto, the picture will not be in focus.❍ Do not look directly at the sun or other strong light sources through the wide
attachment. It could damage your eyesight.❍ When recording in wide angle with the wide attachment, the outer periphery
of the image may become curved.❍ Filters cannot be used with the wide attachment.❍ If dust accumulates on the wide attachment or on the camcorder lens, clean
both lenses gently with a blower brush. ❍ The wide attachment may obstruct the remote sensor (the range of the
wireless controller narrows), or may cause a shadow to appear on the picturewhen recording with a video light or the assist lamp (White LED).
❍ Do not touch the lens to avoid smudges and fingerprints.❍ Do not store the wide attachment in a humid place as it may mold.
MV650i
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 19
20
Mas
teri
ng
th
e B
asic
s
E
Loading a CassetteUse only video cassettes marked with the D logo.
Loading and Unloading1. Slide and hold the OPEN/EJECT
switch and open the cassettecompartment cover.
The cassette compartment opens
automatically.
2. Load/unload the cassette.
• Load the cassette with the window facing
the grip belt and the REC/SAVE tab facing
upward.
• Unload the cassette by pulling it straight
out.
3. Press the P mark on the cassettecompartment until it clicks.
Wait for the cassette compartment to retract
automatically.
4. Close the cassette compartmentcover.
❍ Do not interfere with the cassette compartment while it is opening or closingautomatically or attempt to close the cover until the cassette compartment hasfully retracted.
❍ Be careful not to get your fingers caught in the cassette compartment cover.
❍ If the camcorder is connected to a power source, cassettes can beloaded/unloaded even if the POWER switch is set to OFF.
❍ v flashes if no cassette is inserted when turning on the power (in CAMERAand PLAY (VCR) mode).
❍ With some types of tapes, the remaining tape display may not be accurate.
OPEN/EJECT
e
w
q
PUSHr
Tape protection tab
click
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 20
21
Masterin
g
the B
asicsProtecting Tapes from Accidental ErasureTo protect your recordings from accidental
erasure, slide the tab on the cassette to the
left. (This switch position is usually labelled
SAVE or ERASE OFF.)
If you load a protected cassette in CAMERA
mode, the message “THE TAPE IS SET FOR
ERASURE PREVENTION” appears for approx. 4
seconds and v starts flashing. If you wish to record on that cassette, slide the tab
back to the right.
Cassette Handling Precautions❍ Rewind tapes after use. If the tape becomes slack and damaged, it may cause
picture and sound distortion.
❍ Return cassettes in the case and store them upright.
❍ Do not leave the cassette in the camcorder after use.
❍ Do not use cassettes with spliced tapes or nonstandard cassettes as they may
damage the camcorder.
❍ Do not insert anything into the small holes of the cassette, or cover them with
cellophane tape.
❍ Handle cassettes with care. Do not drop or subject them to severe impact as this
may damage the cassettes.
❍ Rewind tapes from time to time if they are stored for a long time.
❍ With cassettes equipped with a memory function, metal plated terminals may
become dirty with use and the cassette’s memory function may not work properly.
Clean the terminals with a cotton swab after about 10 times of loading/unloading.
E
SAVEREC
SAVEREC
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 21
22
Mas
teri
ng
th
e B
asic
s
E
Using the Wireless ControllerYou can operate the camcorder with the
supplied wireless controller from a distance of
up to 5 m. Point it at the camcorder’s remote
sensor when you press the buttons.
Following functions cannot be operated
without the wireless controller:
• Some special playback modes ( 36)
• Photo/date search ( 84)
• Zero set memory ( 85)
• Analog line-in ( 88)
• DV dubbing ( 89)
• AV Insert ( 93)
• Audio dubbing ( 95)
❍ The wireless controller may not work properly in bright places, such asoutdoors under direct sunlight, or when used too close to the camcorder.
❍ The operable range of the wireless controller may shorten when thecamcorder’s remote sensor is exposed to strong light.
❍ When the batteries run out, replace both at the same time.
Inserting BatteriesThe wireless controller operates with two AA batteries.
1. Open the battery cover.
2. Insert the batteries following the + and – markings.
3. Close the battery cover.
MV600iMV630iMV650i
MV600iMV630iMV650i
MV600iMV630iMV650i
q
w
e
q
w
e
WL-D79MV630iMV650i
WL-D80MV600MV600i
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 22
23
Masterin
g
the B
asics
E
Setting the Time Zone, Date and TimeSet the time zone, date and time when you first start using your camcorder. Install the
backup battery before you begin ( 17).
Setting the Time Zone/Daylight Saving Time
1. Press the MENU button to open the menu.
2. Turn the selector dial to select [SYSTEM] and pressthe selector dial.
3. Turn the selector dial to select [T.ZONE/DST] andpress the selector dial.
• The time zone setting appears.
• The default setting is Paris. Select your time zone and daylight saving time (DST)
setting if necessary.
4. Turn the selector dial to select the setting option that represents yourtime zone.
To adjust for daylight saving time, select the time zone with the U next to the area.
5. Press the MENU button to close the menu.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
T.ZONE/DST•••PARIS SYSTEM
MENU
MENU
( 43)
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 23
24
Mas
teri
ng
th
e B
asic
s
E
❍ Once you have set time zone, date and time, you do not need to reset theclock each time you travel to another time zone. Just set the time zone to theone of your destination, and the camcorder automatically adjusts the clock.
❍ Days per month and leap years will be automatically adjusted.
Setting the Date and Time
1. Press the MENU button to open the menu.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
D/TIME SET••• 1.JAN.2003 12:00 PM
SYSTEM
MENU
1
24 1 2 3 4 5 6 7 8 9 10 11 12 1314 15 16 17 18 19 20 21 22 23
2
3
5
6 7 9
8
10
4
12
11
13
24
19
2018
17
21
23
22
15
14
16
Time zone
LONDONPARISCAIROMOSCOWDUBAIKARACHIDACCABANGKOKH. KONG (Hong Kong)TOKYOSYDNEYSOLOMON
WELLGTN (Wellington)SAMOAHONOLU. (Honolulu)ANCHOR. (Anchorage)L.A. (Los Angeles)DENVERCHICAGON.Y. (New York)CARACASRIO (Rio de Janeiro)FERNAN. (Fernando de Noronha)AZORES
No. Time zoneNo.
( 43)
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 24
25
Masterin
g
the B
asics2. Turn the selector dial to select [SYSTEM] and press
the selector dial.
3. Turn the selector dial to select [D/TIME SET] andpress the selector dial.
The year display starts to flash.
4. Turn the selector dial to select the year, and press the selector dial.
• The next part of the display starts flashing.
• Set the month, day, hours and minutes in the same way.
5. Press the MENU button to close the menu and tostart the clock.
Time zone, date and time appear for 4 seconds each time you
turn the power on.
❍ To change a part of the date or time, press the selector dial at step 4, andmove to the part you wish to change.
❍ The date can be set to any year between 2003 and 2030.
Displaying Date and Time during RecordingYou can display time zone, date and time in the lower left corner of the screen (the
time zone disappears after 4 seconds). The 4-second display will no longer appear
when you turn the power on. The date and time display will not be superimposed on
your recordings.
1. Press the MENU button to open the menu.
2. Turn the selector dial to select [DISPLAY SET UP] andpress the selector dial.
3. Turn the selector dial to select [D/T DISPLAY] andpress the selector dial.
4. Turn the selector dial to select [ON].
5. Press the MENU button to close the menu.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
E
D/T DISPLAY••OFFDISPLAY SET UP
MENU
MENU
MENU
( 43)
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 25
26
Mas
teri
ng
th
e B
asic
s
E
Recording Movies on a TapeYou can use the LCD screen or the viewfinder when recording.
Before You Begin RecordingMake a test recording first to check if the camcorder operates correctly. Before you
make important recordings, clean the video heads ( 141).
Preparations
Connect a power source. Load a cassette.
Recording
1. Remove the lens cap.
2. Set the camcorder to CAMERA mode.
If you have not set the time zone, date and
time, “SET THE TIME ZONE, DATE AND TIME”
appears. See Setting the Time Zone, Date and
Time ( 23).
3. Open the LCD panel ( 30).
To use the viewfinder, keep the LCD panel
closed or rotate it so that the screen faces in
the same direction of the lens ( 31).
4. Press the start/stop button to beginrecording.
Wait until the tape counter came to a
complete stop before you begin recording.
5. Press the start/stop button again topause recording.
Restart recording by pressing the start/stop button.
q
w
OFFOFF
(VCR)(VCR)PLAY
CAMERACAMERA
TAPECARD
r
e
t
OFFOFF
(VCR)(VCR)PLAY
CAMERACAMERA
MV650i/MV630i
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 26
27
Masterin
g
the B
asicsWhen You Have Finished Recording
1. Turn the POWER switch to OFF.
2. Close the LCD panel.
3. Replace the lens cap.
4. Unload the cassette.
5. Disconnect the power source.
When recording outdoors or through a window, do not leave LCD screen,viewfinder or lens exposed to direct sunlight as it may cause damage.
❍ Turn the power off if you do not intend to use the camcorder for a longertime.
❍ The camcorder will shut off after 5 minutes when left in record pause mode toprotect tape and video heads. To continue recording, turn the POWER switchto OFF and then back to CAMERA.
❍ For when to use the [ (Easy Recording) or Q (program AE) mode, see Usingthe Recording Programs ( 56).
❍ When you do not remove the cassette, you can record the next scene withoutproducing any noise or blank sections between the recordings even if you turnthe camcorder off.
❍ About the built-in microphone: When recording near loud sounds (such asfireworks, drums or concerts), sound may become distorted or may berecorded not in the actual sound level.
❍ For extra recording time, see Changing the Recording Mode ( 53).
E
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 27
28
Mas
teri
ng
th
e B
asic
s
E
ZoomingThe camcorder’s zoom lens allows you to choose the best picture angle for your
recordings.
The camcorder automatically switches between optical zooming and digital zooming.
Image resolution is slightly lower with the digital zoom.
Optical Zoom
Move the zoom lever toward W to zoom out (wide-angle). Move it toward T to zoom in (telephoto).
• Press the zoom lever slightly for a slow zoom. Press harder for a
faster zoom.
• You can also use the T and W buttons on the wireless controller.
However, you cannot control the zoom speed.
Digital Zoom
1. Press the MENU button to open the menu.
2. Turn the selector dial to select [CAMERA SET UP] andpress the selector dial.
3. Select [D.ZOOM] and press the selector dial.
4. Select a setting option.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
T
W
Zoom in
Zoom out
22× optical zoom 20× optical zoom 18× optical zoom
MV650i MV600i MV600MV630i
88×/440× digital zoom 80×/400× digital zoom 72×/360× digital zoom
MV650i MV600i MV600MV630i
D.ZOOM•••••••88×CAMERA SET UP
MENU
( 43)
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 28
29
Masterin
g
the B
asics5. Press the MENU button to close the menu.
❍ Keep at least 1m to the subject. At wide-angle, you can focus on a subject asclose as 1cm.
❍ Digital zoom cannot be used in the Night mode and Super Night (MV650i)mode.
❍ Digital zoom cannot be used when the multi-image screen is selected. ❍ A zoom indicator appears for 4 seconds. It extends in light blue when the
digital zoom is set to 88×/80×/72×, and extends further in dark blue when setto 440×/400×/360×.
❍ Because the image stabilizer cannot be used in CARDCAMERA mode, we recommend mounting the camcorder on a tripod at largemagnifications.
MV630iMV650i
E
MENU
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 29
30
Mas
teri
ng
th
e B
asic
s
E
Using the LCD Screen1. Push the OPEN button at the LCD
panel and open the LCD panel.
The LCD screen switches on and the
viewfinder switches off.
2. Rotate the LCD panel and choose theangle of the screen.
You can rotate the LCD panel so that the
screen faces in the same direction as the lens
( 31), or push it flat against the camcorder with the screen facing outward.
3. Close the LCD panel after use.
• Close the LCD panel firmly until it clicks.
• The LCD screen switches off and the
viewfinder switches on.
❍ Make sure to open the LCD panel at 90 degrees before rotating it.❍ Rotate the LCD panel in the vertical position before closing the LCD panel.❍ When recording outdoors or through a window, do not leave the LCD screen,
viewfinder or lens exposed to direct sunlight as it may cause damage.❍ Do not hold the camcorder by the LCD panel or the viewfinder.
❍ About the LCD Screen: The LCD screen is produced with extremely high-precision manufacturing techniques, with more than 99.99% of the pixelsoperating to specification. Less than 0.01% of the pixels may occasionallymisfire or appear as black or green dots. This has no effect on the recordedimage and does not constitute a malfunction.
❍ Bright light or reflected light may cause a vertical light bar to appear on thescreen. This is not a malfunction.
❍ Bright light may make it difficult to use the LCD screen. In such case, use theviewfinder instead.
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 30
31
Masterin
g
the B
asics
E
Adjusting the Brightness of the LCD Screen
1. Press the MENU button to open the menu.
2. Turn the selector dial to select [DISPLAY SET UP] andpress the selector dial.
3. Turn the selector dial to select [BRIGHTNESS] andpress the selector dial.
4. Turn the selector dial and adjust the level.
Turn the selector dial up to make the screen brighter and down to make it darker.
5. Press the MENU button to close the menu.
Changing the brightness of the LCD screen does not affect that of the viewfinderor the recordings.
Allowing the Subject to Monitor the LCD ScreenYou can rotate the LCD panel so that the
screen faces in the same direction as the lens.
The viewfinder switches on allowing you to
use the viewfinder while the subject can
monitor the screen.
When you rotate the screen so that the screen faces in the same direction as the lens,
the image appears mirror reversed (LCD MIRROR ON). However, you can choose to
display the image as it is being recorded (LCD MIRROR OFF).
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
BRIGHTNESS••DISPLAY SET UP – +
MENU
MENU
( 43)
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 31
32
Mas
teri
ng
th
e B
asic
s
E
1. Press the MENU button to open the menu.
2. Turn the selector dial to select [DISPLAY SET UP] and press the selectordial.
3. Turn the selector dial to select [LCD MIRROR] and press the selector dial.
4. Turn the selector dial to select [OFF].
5. Press the MENU button to close the menu.
When [LCD MIRROR] is set to [ON], most screen displays appear mirror reversed.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
LCD MIRROR••ONDISPLAY SET UP( 43)
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 32
33
Masterin
g
the B
asics
E
Searching and Reviewing when Recording
Record Review
In record pause mode, this function allows you to review the last few seconds of your
recording to check if it has been recorded properly.
Press and release the c (record review) button.
The camcorder rewinds the tape, plays back the last few seconds,
and returns to record pause mode.
Record Search
In record pause mode, this function allows you to play back the tape (forward or
reverse) to locate the point where you wish to begin recording.
Press and hold the REC SEARCH + button (forward) or –button (reverse).
• Release the button at the point you wish to begin recording.
• The camcorder returns to record pause mode.
❍ Noise may appear on the screen when you play back the tape in reverse.❍ There will be no sound during Record Review and Record Search.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
REC (record) SEARCH – button/ v Record review button
REC SEARCH + button
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 33
34
Mas
teri
ng
th
e B
asic
s
E
Tips for Making Better VideosHolding the CamcorderFor maximum stability, grip the camcorder in your right hand and keep your right
elbow pressed against your body. If necessary, support the camcorder with your left
hand. Be careful that your fingers do not touch the microphone or lens.
For More Stability
LightingWhen recording outdoors, we recommend
recording with the sun at your back.
❍ When using a tripod, do not leave the viewfinder exposed to direct sunlight asit may melt (due to concentration of the light by the lens).
❍ Do not use tripods with fastening screws longer than 5.5 mm as it maydamage the camcorder.
Low-angle RecordingHigh-angle Recording
Lean against a wall Put the camcorder on a table
Lie on your elbow Use a tripod
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 34
35
Masterin
g
the B
asics
E
Playing Back a TapeWhen you use the LCD screen for playback, the camcorder plays back the sound via
built-in speaker. The built-in speaker is monaural. Use headphones for stereo sound or
when using the viewfinder for playback.
Preparations
Connect a power source. Load a cassette.
Playback
1. Set the camcorder to PLAY (VCR)mode.
2. Open the LCD panel.
You can also close the LCD panel with the
screen facing outward.
3. Press the ` button to rewind thetape.
To fast forward the tape, press the 1
button. To stop playback, press the 3 button.
4. Press the e/a button to beginplayback.
5. Press the 3 button to stop playback.
❍ If the playback picture is distorted, clean the video heads using a Canon HeadCleaning Cassette or a commercially available digital video head-cleaningcassette.
❍ To use the viewfinder, close the LCD panel. The built-in speaker does notsound. Use headphones when using the viewfinder ( 37).
❍ For displaying the date and time during playback, see Displaying the Data Code( 82).
q
TAPECARD
OFF
(VCR)(VCR)PLAY
CAMERA
w
e tr
MV650i/MV630i
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 35
36
Mas
teri
ng
th
e B
asic
s
E
Special Playback ModesSpecial playback modes (except of playback pause and fast/rewind playback) can only
be operated with the wireless controller.
e/a (Playback Pause) To pause playback, press the e/a button. Press the e/a button to resume playback.
The camcorder goes into stop mode after 5 minutes in playback pause mode.
1 (Fast Forward Playback) / ` (Rewind Playback)Plays back the tape at 11.5 times normal speed (forward or reverse). Press and hold
the button during normal playback or fast forward.
+/ae (Frame Advance) / –/4a (Frame Reverse)Plays back frame-by-frame. Press the button repeatedly during playback pause. Press
and hold it to play back continuous frame advance/frame reverse.
SLOW I (Slow Forward)/(Slow Reverse)Plays back at about 1/3 normal speed. For slow forward playback, press the SLOW M
button. For slow reverse playback, press the –/4a button followed by the SLOW M
button. Press the e (play) button to return to normal playback.
–/4a (Reverse Playback)Plays back in reverse at normal speed. Press the button during normal playback. Press
the e (play) button return to normal playback. The camcorder goes into stop mode
after 5 minutes in reverse playback pause.
× 2 (Forward× 2 Playback)/(Reverse 2× Playback)Plays back at 2 times normal speed. Press the button during normal or reverse
playback. Press the e (play) button return to normal playback.
❍ There is no sound during special playback.❍ The picture may become distorted during some special playback modes.
PAUSE SLOW 2
STOP
REW PLAY FF
` (rewind) button1 (fast forward) button
e/a (play/pause) button3 (stop) button
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 36
37
Masterin
g
the B
asicsPlaying Back with the Built-in Speaker/Headphones
When using the built-in speaker, make sure that “H” is not displayed on thescreen. When using the headphones, make sure that “H” is displayed. Changethe setting as necessary following the procedure below.
Switching the AV/Headphones Terminal
1. Press the MENU button to open the menu.
2. Turn the selector dial to select [VCR SET UP] andpress the selector dial.
3. Turn the selector dial to select [AV/PHONES] andpress the selector dial.
4. Turn the selector dial to select [AV] or [PHONES H].
5. Press the MENU button to close the menu.
❍ The built-in speaker does not sound when “H” is displayed. ❍ Do not connect headphones unless “H” is displayed as it produces noise.❍ The built-in speaker is monaural. Use headphones for stereo sound.❍ The built-in speaker turns off when the camcorder is set to a mode other than
the PLAY (VCR) mode or when you use the headphones.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
E
AV
AV/PHONES•••AVVCR SET UP
MENU
MENU
Selector dialMENU button
Built-in speaker
( 43)
H (phones) terminal
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 37
38
Mas
teri
ng
th
e B
asic
s
E
Adjusting the Volume
*Headphone volume only.
Turn the selector dial up to increase the volume, anddown to lower the volume.
• A volume bar appears for 4 seconds.
• You can turn off the volume completely by turning the selector
dial down until OFF appears. Turn the selector dial up to increase the volume again.
❍ Sound may become distorted when the volume is turned up too high.❍ The headphone volume can be adjusted in all operating modes.❍ The camcorder retains the setting even if you turn it off (separately for
headphones and built-in speaker).
CARD PLAY (VCR)CARD CAMERA*PLAY (VCR)CAMERA*
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 38
39
Masterin
g
the B
asics
E
Playing Back on a TV ScreenYou can connect the camcorder to a TV or VCR to play back your recordings on a TV
screen.
❍ Make sure that “H” is not displayed on the screen. If “H” is displayed on thescreen, change the setting ( 37).
❍ When you use the TV as a monitor during recording, keep the TV volumeturned down as long as the camcorder’s audio terminals are connected. Anunpleasant high-pitched squeal, called feedback, may be produced if soundfrom the TV speakers is picked up by the microphone.
For high picture quality, we recommend using a TV with an S (S1) terminal.
TVs with SCART TerminalRefer also to the TV or VCR instruction manual.
1. Turn off all devices before starting the connections.
2. Connect the PC-A10 SCART adapter to the TV or VCR’s SCART terminal.
3. Connect the STV-250N Video Cable to the camcorder’s AV terminal andthe audio/video terminals on the SCART adapter.
Connect the white plug to the white AUDIO terminal L (left), the red plug to the red
AUDIO terminal R (right) and the yellow plug to the yellow VIDEO terminal.
AV
AUD
IO(L/M
ON
O)
AUD
IO(R
)VID
EO
Signal flow
STV-250N Stereo Video Cable (supplied)
PC-A10 SCART Adapter (supplied)
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 39
40
Mas
teri
ng
th
e B
asic
s4. If connecting to a TV, set the input selector to VIDEO. If connecting to a
VCR, set the input selector to LINE.
The SCART Adapter PC-A10 is for output only. For analog line-in recording oranalog-digital conversion, please use a SCART adapter with input capability(commercially available).
TVs with S (S1)-Video Input TerminalRefer also to the TV or VCR instruction manual.
1. Turn off all devices before starting the connections.
2. Connect the S-150 S-video Cable (optional) to the S-video terminals.
3. Connect the STV-250N Stereo Video Cable to the camcorder’s AVterminal and the audio terminals of the TV/VCR.
Connect the white plug to the white AUDIO terminal L (left), and the red plug to the
red AUDIO terminal R (right). Do not connect the yellow plug.
4. If connecting to a TV, set the input selector to VIDEO. If connecting to aVCR, set the input selector to LINE.
E
VIDEO
S(S1)-VIDEO
INPUT
AUDIOL
R
S DV
AV
Signal flow
S-150 S-video Cable (optional)
Signal flow
STV-250N Stereo Video Cable (supplied)
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 40
41
Masterin
g
the B
asicsTVs with Audio/Video TerminalsRefer also to the TV or VCR instruction manual.
1. Turn off all devices before starting the connections.
2. Connect the STV-250N Stereo Video Cable to the camcorder’s AVterminal and the audio/video terminals on the TV/VCR.
Connect the white plug to the white audio terminal L (left), the red plug to the red
audio terminal R (right) and the yellow plug to the yellow video terminal VIDEO.
3. If connecting to a TV, set the input selector to VIDEO. If connecting to aVCR, set the input selector to LINE.
E
AV
VIDEO
AUDIOL
RSignal flow
STV-250N Stereo Video Cable (supplied)
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 41
42
Mas
teri
ng
th
e B
asic
s
E
Selecting the Audio Output ChannelYou can select the output channels when playing back a tape with audio recorded on
two channels.
1. Press the MENU button to open the menu.
2. Turn the selector dial to select [AUDIO SET UP] andpress the selector dial.
3. Turn the selector dial to select [OUTPUT CH] andpress the selector dial.
4. Turn the selector dial to select a setting option.
• L/R: Stereo: L+R channels, Bilingual: Main+Sub.
• L/L: Stereo: L channel, Bilingual: Main.
• R/R:Stereo: R channel, Bilingual: Sub.
5. Press the MENU button to close the menu.
The setting resets to the L/R setting when you turn the camcorder off.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
MENU
OUTPUT CH•••L/RAUDIO SET UP
MENU
( 43)
2_D73PAL_E(13-42) 02.12.26 9:22 PM Page 42
43
Usin
g th
e Full R
ang
e o
f Features
E
Menus and SettingsMany of the camcorder’s advanced functions are selected from menus that appear on
the screen.
Selecting Menus and Settings1. Set the camcorder to the correct operating mode.
2. Press the MENU button to open the menu.
3. Turn the selector dial to select a submenu and pressthe selector dial.
4. Turn the selector dial to select a menu item andpress the selector dial.
5. Turn the selector dial to select a setting option.
6. Press the MENU button to close the menu.
When setting the white balance or shutter speed, press the
selector dial first before pressing the MENU button.
❍ Pressing the MENU button at any time closes the menu.❍ Selecting [[ RETURN] takes you back one level.❍ Items that are not available appear in purple.❍ You may find it more convenient to use the wireless controller to operate the
menu. Press the MENU button on the wireless controller to open or close themenu. Use the arrow keys in place of the selector dial and press the SET buttonin place of pressing the selector dial.
OFF
(VCR)PLAY
CAMERA
TAPE
CARD
MENU
MENU
MV650i/MV630i
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 43
44
Usi
ng
th
e Fu
ll R
ang
e o
f Fe
atu
res
E
Menu and Default SettingsDefault settings are shown in boldface.
CAMERA Menu (CAM. MENU)
CARD CAMERACARD CAMERAPLAY (VCR)CAMERA
Submenu Menu Item Setting Options\ CARD MIX *2 MIX TYPE CARD CHROMA, CARD LUMI., 121
CAM. CHROMA, C. ANIMATIONANIMAT. TYPE CORNER, STRAIGHT, RANDOM 122
MIX LEVEL 121
CAMERA SET UP SHUTTER AUTO, 1/50, 1/120, 1/250, 1/500, 1/1000, 771/2000
D. ZOOM MV650i MV630i MV600i/MV600 28OFF, 88×, 440× OFF, 80×, 400× OFF, 72×, 360×
IMAGE S. ON, OFF 68
16:9 ON, OFF 51WHITE BAL. AUTO, SET W, INDOOR T, OUTDOOR U 79
VCR SET UP REC MODE SP, LP 53
AV/PHONES AV, PHONES H 37
AUDIO SET UP WIND SCREEN ON, OFF 70
AUDIO MODE 16bit, 12bit 70
DISPLAY SET UP BRIGHTNESS 31
LCD MIRROR ON, OFF 32
TV SCREEN ON, OFF 133
D/T DISPLAY ON, OFF 25
DEMO MODE ON, OFF 52
SYSTEM BUTTONLIGHT *1 ON, PUSH ON, OFF 50
LIGHT COLOR *1 GREEN, ORANGE, BLUE, YELLOW, 50TURQUOISE, PURPLE
WL. REMOTE A1, A2, OFF B 48
BEEP ON, OFF 51
T.ZONE/DST See list of time zones 23
D/TIME SET 24
MY CAMERA S-UP IMAGE *3 ON, OFF 49
SHTR SOUND *2 PATTERN1, PATTERN2, PATTERN3 49
S-UP SOUND PATTERN1, PATTERN2, PATTERN3 49
S/STOP SOUND PATTERN1, PATTERN2, PATTERN3 49
SELF-T SOUND PATTERN1, PATTERN2, PATTERN3 49
*1 , *2 , *3MV650i MV650i MV600i MV600MV630i
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 44
45
Usin
g th
e Full R
ang
e o
f Features
E
PLAY (VCR) Menu (VCR MENU)
CARD CAMERACARD CAMERAPLAY (VCR)CAMERA
Submenu Menu Item Setting OptionsVCR SET UP REC MODE *4 SP, LP 53
AV/PHONES AV, PHONES H 37
AV \ DV OUT *4 ON, OFF 92
AUDIO SET UP OUTPUT CH L/R, L/L, R/R 42
AUDIO DUB *4 AUDIO IN, MIC. IN 96
WIND SCREEN ON, OFF 70
AUDIO MODE *4 16bit, 12bit 70
12bit AUDIO STEREO1, STEREO2, MIX/FIXED, MIX/VARI. 97
MIX BALANCE 97
CARD SET UP *2 SI QUALITY SUPER FINE, FINE, NORMAL 100
MOVIE SIZE *1 320 × 240, 160 × 120 101
FILE NOS. RESET, CONTINUOUS 102
CARD COPY \ CANCEL, EXECUTE 125OPERATIONS *2 DISPLAY SET UP BRIGHTNESS 31
DISPLAYS ON, OFF <PLAYBK> 133
6SEC. DATE ON, OFF 83
DATA CODE DATE/TIME, CAMERA DATA, CAM. & D/T 83
D/TIME SEL. DATE, TIME, DATE & TIME 83
SYSTEM BUTTONLIGHT *1 ON, PUSH ON, OFF 50
LIGHT COLOR *1 GREEN, ORANGE, BLUE, YELLOW, 50TURQUOISE, PURPLE
WL. REMOTE A1, A2, OFF B 48 BEEP ON, OFF 51
T.ZONE/DST See list of time zones 23
D/TIME SET 24
MY CAMERA S-UP IMAGE*3 ON, OFF 49
SHTR SOUND *2 PATTERN1, PATTERN2, PATTERN3 49
S-UP SOUND PATTERN1, PATTERN2, PATTERN3 49
S/STOP SOUND PATTERN1, PATTERN2, PATTERN3 49
SELF-T SOUND PATTERN1, PATTERN2, PATTERN3 49
*1 , *2 , *3MV650i MV650i MV600i MV600 MV600MV630i , *4 Does not appear with the .
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 45
46
Usi
ng
th
e Fu
ll R
ang
e o
f Fe
atu
res
E
CARD CAMERA Menu (C. CAM. MENU)
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
MV630iMV650i
Submenu Menu Item Setting OptionsCAMERA SET UP SHUTTER AUTO, 1/50, 1/120, 1/250 77
WHITE BAL. AUTO, SET W, INDOOR T, OUTDOOR U 79
CARD SET UP SI QUALITY SUPER FINE, FINE, NORMAL 100
SI SIZE 1024 × 768, 640 × 480 100
MOVIE SIZE *1 320 × 240, 160 × 120 101
FILE NOS. RESET, CONTINUOUS 102
VCR SET UP AV/PHONES AV, PHONES H 37
AUDIO SET UP *1 WIND SCREEN ON, OFF 70
DISPLAY SET UP BRIGHTNESS 31
LCD MIRROR ON, OFF 32
TV SCREEN ON, OFF 133
D/T DISPLAY ON, OFF 25
DEMO MODE ON, OFF 52
SYSTEM BUTTONLIGHT *1 ON, PUSH ON, OFF 50
LIGHT COLOR *1 GREEN, ORANGE, BLUE, YELLOW, 50TURQUOISE, PURPLE
WL. REMOTE A1, A2, OFF B 48
BEEP ON, OFF 51
T.ZONE/DST See list of time zones 23
D/TIME SET 24
MY CAMERA SHTR SOUND PATTERN1, PATTERN2, PATTERN3 49
S-UP SOUND PATTERN1, PATTERN2, PATTERN3 49
S/STOP SOUND PATTERN1, PATTERN2, PATTERN3 49
SELF-T SOUND PATTERN1, PATTERN2, PATTERN3 49
MV650i*1
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 46
47
Usin
g th
e Full R
ang
e o
f Features
E
CARD PLAY (VCR) Menu (C.PLAY MENU)
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
MV630iMV650i
Submenu Menu Item Setting OptionsCARD COPY \ CANCEL, EXECUTE 126OPERATIONS (Single Image PRINT ORDERS YES, NO 116Display) ALL ERASE
IMAGE ERASE CANCEL, SINGLE, ALL 114
FORMAT CANCEL, EXECUTE 127
CARD \ PROTECT 113OPERATIONS(Index Screen) \ PRINT ORDER 115
VCR SET UP REC MODE SP, LP 53
AV/PHONES AV, PHONES H 37
DISPLAY SET UP BRIGHTNESS 31
DISPLAYS ON, OFF 133
D/TIME SEL. DATE, TIME, DATE & TIME 83
SYSTEM BUTTONLIGHT *1 ON, PUSH ON, OFF 50
LIGHT COLOR *1 GREEN, ORANGE, BLUE, YELLOW, 50TURQUOISE, PURPLE
WL. REMOTE A1, A2, OFF A 48
BEEP ON, OFF 51
T.ZONE/DST See list of time zones 23 D/TIME SET 24
MY CAMERA CREATE START-UP IMAGE 129
SEL. S-UP IMG NO IMAGE, CANON LOGO, MY IMAGE 49
SHTR SOUND PATTERN1, PATTERN2, PATTERN3 49
S-UP SOUND PATTERN1, PATTERN2, PATTERN3 49
S/STOP SOUND PATTERN1, PATTERN2, PATTERN3 49
SELF-T SOUND PATTERN1, PATTERN2, PATTERN3 49
\ PRINT Appears when connecting a printer with direct print function. 117
*1 MV650i
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 47
48
Usi
ng
th
e Fu
ll R
ang
e o
f Fe
atu
res
E
Changing the Remote Sensor ModeTwo remote sensor modes and an off setting are available to prevent interference
from other Canon wireless controllers being used nearby.
Turning the Remote Sensor Off
Open the menu and select [SYSTEM]. Select [WL.REMOTE], set it to [OFF B] and close the menu.
”B” appears.
Changing the Remote Sensor Mode
1. On the camcorder, open the menu and select[SYSTEM]. Select [WL. REMOTE], set it to [A 2] andclose the menu.
The selected mode appears for 4 seconds.
2. On the wireless controller, press and hold theREMOTE SET button. Set the mode to the same ofthe camcorder. Press the ZOOM T button for mode 2.Keep the button pressed for over 2 seconds.
If you have set the camcorder to mode 1, press the ZOOM W
button for mode 1.
❍ The wireless controller returns to mode 1 when you replace the batteries.Change the mode if necessary.
❍ Make sure that camcorder and wireless controller are set to the same mode.Display the camcorder’s mode by pressing any button on the wireless controller(except of the REMOTE SET button) and set the wireless controller’s mode tothe same mode. Change the batteries if the wireless controller still does notwork.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
WL.REMOTE••• 1SYSTEM
WIRELESS CONTROLLER WL-D79
PAUSE
AV INSERT AV DV REMOTE SET
SLOW 2
RECPAUSE
AUDIO DUB.
W TSTART/STOP PHOTO
ZOOM
SELF T. D.EFFECT.
ON/OFF SET
MENU
TV SCREEN
( 43)
( 43)
WL.REMOTE••• 1SYSTEM
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 48
49
Usin
g th
e Full R
ang
e o
f Features
E
Customizing the CamcorderYou can personalise your camcorder by customizing the start-up image and the sound
it makes for start-up, shutter*, start/stop and self-timer (collectively called the My
Camera settings).
* MV650i and MV630i only. With the MV650i and MV630i, you can also create your
own start-up image. See Creating a Start-up Image ( 129).
Changing the My Camera Settings
1. Open the menu and select [MY CAMERA].
2. Select the menu item you wish to change.
• When selecting a start-up image (only in CARD PLAY (VCR) mode):
[NO IMAGE], [CANON LOGO] and [MY IMAGE] appears.
• When selecting a start-up image: [OFF] and [ON] appears.
• When selecting a sound: [PATTERN1], [PATTERN2] and [PATTERN3] appear.
3. Select a setting option and close the menu.
MV600MV600i
MV630iMV650i
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
SHTR SOUND•••PATTERN1
S–UP SOUND•••PATTERN1
S/STOP SOUND•PATTERN1
SELF–T SOUND•PATTERN1
MY CAMERA S–UP IMAGE•••ON( 43)
(MV600i/MV600)
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 49
50
Usi
ng
th
e Fu
ll R
ang
e o
f Fe
atu
res
E
Setting the Light-up ButtonsThe buttons above the LCD panel light up
when the camcorder’s power is on, or when
you press a button. This is helpful if, for
example, you wish to play back a tape in dark
places.
You can select the colour of the light-up
buttons from green, orange, blue, yellow,
turquoise and purple.
Selecting the Light-up Setting
Open the menu and select [SYSTEM]. Select [BUTTONLIGHT], set it to[PUSH ON] or [OFF] and close the menu.
• ON: The buttons light up while the camcorder is turned on. The colour changes when
you press a button and turns back when you release the button.
• PUSH ON: The buttons light up when you press a button and turn off when you release
the button.
• OFF: Buttons do not light up.
Selecting the Colour of the Buttons
Open the menu and select [SYSTEM]. Select [LIGHT COLOR], set it to thedesired colour and close the menu.
You cannot change the colour of the buttons when [BUTTONLIGHT] is set to[OFF].
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
MV650i
BUTTONLIGHT•ONSYSTEM
LIGHT COLOR•TURQUOISESYSTEM
MENU button
Selector dial
( 43)
( 43)
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 50
51
Usin
g th
e Full R
ang
e o
f Features
E
Other Camcorder Settings
BeepYou will hear a beep upon camcorder operations such as power on/off, start/stop, self-
timer countdown, automatic shut-off, and unusual conditions of the camcorder. The
beep will not be recorded.
If you turn off the beep, all camcorder sounds including the ones of the My Camera
settings will be turned off.
To turn the beep off, open the menu and select [SYSTEM]. Select [BEEP],set it to [OFF] and close the menu.
Recording in 16:9 (Wide Screen TV Recording)You can record in the 16:9 format for playback on wide screen TVs.
To switch 16:9 on, open the menu and select [CAMERA SET UP]. Select[16:9], set it to [ON] and close the menu.
”16:9” appears.
❍ The 16:9 mode cannot be selected in the Easy Recording mode.❍ The multi-image screen cannot be used when the 16:9 format is selected.❍ If you play back a 16:9 recording on a normal TV, the image appears vertically
“squashed” (compressed).
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
BEEP•••••••••ONSYSTEM
16:9••••••••OFFCAMERA SET UP
( 43)
( 43)
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 51
52
Usi
ng
th
e Fu
ll R
ang
e o
f Fe
atu
res
Demonstration ModeThe demonstration mode displays the camcorder’s main features. It starts
automatically when you leave the camcorder turned on without loading a cassette
(MV650i/MV630i: and without inserting a memory card) for more than 5 minutes. You
can also start the demonstration mode through the menu.
With no cassette (MV650i/MV630i: and memory card) inserted, open themenu and select [DISPLAY SET UP]. Select [DEMO MODE], set it to [OFF]and close the menu.
To cancel the demo mode, press any button, turn off the camcorder, load a cassette
(MV650i/MV630i: or insert a memory card).
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
E
DEMO MODE•••ONDISPLAY SET UP( 43)
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 52
53
Usin
g th
e Full R
ang
e o
f Features
E
Changing the Recording Mode (SP/LP)You can choose from SP (standard play) and LP (long play). LP extends the tape usage
by 1.5 times.
❍ Tapes recorded in LP mode cannot be used for audio dubbing ( 95) or AVinsert ( 93).
❍ Depending on the nature and usage condition of the tape, picture and soundrecorded in LP mode may be distorted. We recommend using the SP mode forimportant recordings.
❍ We recommend recording in SP mode if you plan to transfer the images to acomputer.
❍ If you record in both SP and LP modes on the same tape, the playback picturemay become distorted and the time code may not be written correctly.
❍ If you play back a tape that has been recorded in LP mode with another digitaldevice on this camcorder, or vice versa, picture and sound may becomedistorted.
* MV650i/MV630i/MV600i only.
To change to LP mode, open the menu and select [VCR SET UP]. Select[REC MODE], set it to [LP] and close the menu.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)*CAMERA
REC MODE••••SPVCR SET UP( 43)
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 53
54
Usi
ng
th
e Fu
ll R
ang
e o
f Fe
atu
res
E
Recording Still Images on a TapeYou can record still images on the tape. Starting your recording with a still image
allows you to easily locate the beginning of the recording with the Photo Search
function ( 84).
In Record Pause Mode
1. Press the PHOTO button halfway.
• Autofocus: F flashes in white and turns green when focus is
adjusted.
• Manual focus: F flashes in green. Adjust the focus with the
selector dial.
• Exposure is locked.
• When you press the PHOTO button on the wireless controller, recording starts
immediately.
2. Press the PHOTO button fully.
• F disappears.
• The camcorder records the still image for approx. 6 seconds.
During this time, the camcorder displays the still image and
keeps recording the sound.
• The camcorder returns to record pause mode.
During Recording
1. Press the PHOTO button fully.
• The camcorder records the still image for approx. 6 seconds.
During this time, the camcorder displays the still image and
keeps recording the sound.
• The camcorder returns to record pause mode.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
PHOTO
PHOTO
PHOTO
PHOTO button
PHOTO button
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 54
55
Usin
g th
e Full R
ang
e o
f Features
❍ When you turn the POWER switch to OFF while the camcorder is recording thestill image, it will not turn off until recording is complete.
❍ Record still images under sufficient lighting condition (in which you can identifythe subject on the screen).
❍ If a subject is unsuitable for autofocus, F continues to flash. Keep the PHOTObutton pressed halfway and adjust the focus with the selector dial.
E
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 55
56
Usi
ng
th
e Fu
ll R
ang
e o
f Fe
atu
res
E
Using the Recording ProgramsThe camcorder is equipped with the Easy Recording program and several program AE
modes. The availability of functions differs depending on the selected mode.
Availability of Functions in Each Mode:
A: Auto setting h: Available ×: Not available*1 MV650i only.*2 The image stabilizer cannot be used in CARD CAMERA mode. *3 Available effects depend upon the program AE mode.*4 MV650i and MV630i only.
Easy Recording ProgramThe camcorder adjusts focus, exposure and other settings
automatically, allowing you to just point and shoot.
Program AE ModesAuto
The camcorder adjusts focus, exposure and other settings
automatically. However, you have the option of adjusting the
settings manually.
[
Position of the Program Selector
Recording Program
Digital Zoom h h ×
Shutter Speed h A
FocusA
h
White Balance h
AE Shift h
Image Stabilizer*2 ON h ×
Digital Effects × h*3
16:9 × h
Card Mix*4 × h ×
[
[
Q
*1 *1
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 56
57
Usin
g th
e Full R
ang
e o
f Features
E
SportsUse this mode to record sports scenes (such as tennis or golf),
moving objects (such as roller coasters) or when recording from a
moving car.
❍ This mode is set at a high shutter speed and should therefore be used
in sufficient light.
❍ This mode is mainly intended for frame-by-frame or slow playback. The picture may not
appear smooth when played back in normal speed.
PortraitUse this mode to give accent to your subject by blurring the
background or foreground.
❍ The blur effect increases the more you zoom to telephoto.
❍ This mode is set at a higher shutter speed. The picture may not appear
smooth when played back.
SpotlightUse this mode to record spotlit scenes such as shows, recitals or
fireworks.
Sand & SnowUse this mode in bright places such as a sunny beach or ski resort. It
prevents the subject from being underexposed.
❍ The subject may become overexposed in dark surroundings. Check the
image on the screen.
❍ This mode is set at a higher shutter speed. The picture may not appear smooth when
played back.
Low LightUse this mode to record in dimly lit places. The shutter is fixed at a
slow shutter speed.
❍ Moving subjects may leave a trailing afterimage.
❍ Picture quality may not be as good as in other modes.
❍ The camcorder may have difficulty to focus automatically.
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 57
58
Usi
ng
th
e Fu
ll R
ang
e o
f Fe
atu
res
NightUse this mode to record in dark places. The shutter speed is
adjusted automatically. It is useful when recording in places with
changing light conditions (such as in amusement parks).
❍ Night mode cannot be used in CARD CAMERA
mode.
❍ Moving subjects may leave a trailing afterimage.
❍ Picture quality may not be as good as in other modes.
❍ White points may appear on the screen.
❍ Autofocus may not work as well as in other modes. In such case, adjust the focus manually.
Super Night (CAMERA mode)In CAMERA mode, use this mode to record in very dark places. The
shutter speed is adjusted automatically. The White LED lights up
automatically illuminating the subject in the centre of the screen,
allowing you to record brightly in colour.
Low Light Plus (CARD CAMERA mode)In CARD CAMERA mode, use this mode to record in dark places.
The shutter is fixed at a slow shutter speed. The White LED lights up
illuminating the subject in the centre of the screen, allowing you to
record brightly in colour.
❍ The range of the White LED is limited. Check the image on the screen when recording.
❍ Use this mode for recordings at close range (up to 2m).
❍ Moving subjects may leave a trailing afterimage.
❍ Picture quality may not be as good as in other modes.
❍ White points may appear on the screen.
❍ Autofocus may not work as well as in other modes. In such case, adjust the focus manually.
MV650i
MV630iMV650i
E
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 58
59
Usin
g th
e Full R
ang
e o
f Features
Selecting the Program AE Mode
1. Slide the program selector to Q (program AE).
2. Press the selector dial.
A list of the program AE modes appears.
3. Select a mode and press the selector dial.
The symbol of the mode appears on the upper left corner of the
screen. (Auto) disappears after 4 seconds.
❍ Do not change the mode during recording as the brightness of the image maychange abruptly.
❍ The setting resets to the Auto mode when you switch the program selector to[.
❍ Bright light in a dark scene may cause a vertical light bar to appear. This is nota malfunction.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
E
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 59
60
Usi
ng
th
e Fu
ll R
ang
e o
f Fe
atu
res
E
Using Digital EffectsYou can use the digital effects during recording and playback.
Faders ( 61): Begin or end scenes with a fade to or from black.
Effects ( 64): Add flavor to your recordings.
Multi-image screen ( 66)
Availability of Digital Effects by Operating Modes:
h: Available i: Not available
*1: Black and White only.
*2: Cannot be used in Night and Super Night (MV650i) mode.
❍ Turn off the digital effect when you do not use it. Press the DIGITAL EFFECTS button to open the menu. Select [D.EFFECTS |]and press the ON/OFF button.
❍ The camcorder retains the setting even if you turn it off or change the programAE mode.
❍ The digital effect turns off if you switch the program selector to [.❍ Digital effects can be selected but not activated on a blank blue screen
(appears in PLAY (VCR) mode).❍ Digital effects activated during playback do not change the recording.❍ Digital effects cannot be used during DV dubbing and photo/date search.❍ Digital effects can also be set with the wireless controller.
CAMERAPLAY (VCR)
MV650i/MV630i: MV650i/MV630i:
Movies Still Images CARD CAMERA CARD PLAY (VCR)
Faders h i h i i
Effects h h h h*1 i
Multi-image h*2 h*2 h i iscreen
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 60
61
Usin
g th
e Full R
ang
e o
f Features
FadersFade Trigger (FADE-T)
Wipe (WIPE)
Corner Wipe (CORNER)
Jump (JUMP)
Flip (FLIP)
EThe image gradually fades in.
The image gradually fades out.
The image begins as a vertical line in the centre and expands sideways until it fills the whole screen.
The image is wiped off from thesides of the screen.
The image appears from the corners until it fills the whole screen.
The image is wiped off from thecorners.
A small image appears fromthe left, jumps into the centre and enlarges until it fills the whole screen.
The image shrinks, jumps fromthe centre to the left anddisappears.
The image flips into the screen.
The image flips out of the screen.
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 61
62
Usi
ng
th
e Fu
ll R
ang
e o
f Fe
atu
res
E
Puzzle (PUZZLE)
Zigzag (ZIGZAG)
Beam (BEAM)
Tide (TIDE)
The image appears in 16 pieces.The pieces move around until the puzzle is solved.
The image is divided into 16pieces. The pieces move aroundand disappear.
The image appears in zigzagfrom the top of the screen.
Black stripes appear in zigzagfrom the bottom of the screenuntil they cover the whole image.
The screen turns yellow, formsa beam that becomes thinner and the image appears.
A yellow beam appears in thecentre of the screen and expandsuntil it covers the whole image.
The image appears fromboth sides like tides.
The image disappears from bothsides like tides.
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 62
63
Usin
g th
e Full R
ang
e o
f Features
Selecting a Fader
1. In CAMERA mode, set the program selector to Q.
2. Press the DIGITAL EFFECTS button.
[D.EFFECTS |], [FADER], [EFFECT] and [MULTI-S] appear.
3. Select [FADER].
4. Select the fader option.
5. Press the DIGITAL EFFECTS button.
The name of the selected fader flashes.
CAMERA mode:
6. Fade in: In record pause mode, press the ON/OFFbutton and begin recording by pressing thestart/stop button.Fade out: During recording, press the ON/OFF buttonand pause recording by pressing the start/stop button.
The fader can be activated/deactivated by pressing the ON/OFF button.
PLAY (VCR) mode:
6. Fade in: In playback pause mode, press the ON/OFFbutton and begin playback by pressing the e/abutton.Fade out: During playback, press the ON/OFF buttonand pause playback by pressing the e/a button.
The fader can be activated/deactivated by pressing the ON/OFF button.
Faders cannot be selected when Card Mix is activated.MV630iMV650i
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
E
DIGITALEFFECTS
ON/OFF
ON/OFF
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 63
64
Usi
ng
th
e Fu
ll R
ang
e o
f Fe
atu
res
E
EffectsArt (ART)The image becomes like a paint (solarization).
Black and White (BLK & WHT)The image becomes black and white.
Sepia (SEPIA)The image becomes monochrome with a brownish tint.
Mosaic (MOSAIC)The image is blurred through enlarging the size of some pixels.
Ball (BALL)The image becomes like a ball.
Cube (CUBE)The image becomes a cube and rotates.
Wave (WAVE)Both ends of the image sway in waves.
Colour Masking (COLOR M.)The image becomes a rhombus surrounded by a masking frame that
changes the colours.
Mirror (MIRROR)Creates a symmetrical image as if there would be a mirror in the
centre of the screen.
Only Black and White can be used in CARD CAMERA mode.MV630iMV650i
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 64
65
Usin
g th
e Full R
ang
e o
f Features
Selecting an Effect
1. Press the DIGITAL EFFECTS button.
[D.EFFECTS OFF], [FADER], [EFFECT] and [MULTI-S] appear.
2. Select [EFFECT].
3. Select the effect.
4. Press the DIGITAL EFFECTS button.
The name of the selected effect flashes.
5. Press the ON/OFF button.
• The name of the selected effect stops flashing.
• The effect can be activated/deactivated by pressing the ON/OFF
button.
Selecting an Effect in CARD CAMERA Mode
1. Press the DIGITAL EFFECTS button.
“BLK&WHT” flashes.
2. Press the ON/OFF button.
• “BLK&WHT” stops flashing.
• The effect can be activated/deactivated by pressing the ON/OFF
button.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
MV630iMV650i
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
EDIGITALEFFECTS
DIGITALEFFECTS
ON/OFF
DIGITALEFFECTS
ON/OFF
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 65
66
Usi
ng
th
e Fu
ll R
ang
e o
f Fe
atu
res
E
Using the Multi-Image ScreenThe multi-image screen captures moving subjects in 4, 9 or 16 sequences of still images
with the Image Capture feature and displays them at one time. Sound will be
recorded normally. This feature can be used in CAMERA and PLAY (VCR) mode.
You can choose the transition speed at which to capture the subject from manual, fast
(every 4 frames), moderate (every 6 frames*) or slow (every 8 frames*).
* In Low Light mode: moderate (every 8 frames), slow (every 12 frames).
Selecting the Multi-Image Screen
1. Set the program selector to Q.
2. Press the DIGITAL EFFECTS button.
[D.EFFECTS |], [FADER], [EFFECT] and [MULTI-S] appear.
3. Select [MULTI-S].
[S.SPEED] and [S.SPLIT] appears.
4. Select [S.SPEED].
[MANUAL], [FAST], [MOD.] and [SLOW] appear.
5. Select the transition speed.
6. Select [MULTI-S] again.
[S.SPEED] and [S.SPLIT] appears.
7. Select [S.SPLIT].
[4], [9], [16] settings appear.
8. Select the number of sequences.
9. Press the DIGITAL EFFECTS button.
[MULTI-S] flashes.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
DIGITALEFFECTS
DIGITALEFFECTS
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 66
67
Usin
g th
e Full R
ang
e o
f Features
Capturing
10.Press the ON/OFF button.
• MANUAL: Images will be captured each time you press the ON/OFF button. The blue
frame indicating the next sequence disappears after the last image. To cancel the last
captured image, press and hold the ON/OFF button. To cancel the multi-image screen,
press and release the ON/OFF button.
• FAST, MODERATE, SLOW: The set number of images will be captured at the set speed.
To cancel the multi-image screen, press the ON/OFF button.
11.Press the start/stop button begin recording.
The multi-image screen is recorded on the tape.
❍ The multi-image screen cannot be operated in Night and Super Night (MV650i)mode.
❍ You can operate the multi-image screen only in the following playback modes:- When [S.SPEED] is set to [MANUAL]: Playback pause, slow forward/reverse
playback- When [S.SPEED] is set to [FAST], [MOD.] or [SLOW]: Playback pause
❍ The multi-image screen can be operated in record or record pause mode.❍ The multi-image screen cannot be selected when Card Mix is
activated.❍ In PLAY (VCR) mode: Pressing any tape operation button (such as play or
pause), or performing date/photo search cancels the multi-image screen.
MV630iMV650i
E
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 67
68
Usi
ng
th
e Fu
ll R
ang
e o
f Fe
atu
res
E
Turning Off the Image StabilizerThe image stabilizer allows you to obtain steady recordings even at telephoto. There is
no need to turn off the image stabilizer during normal recording. However, the
camcorder tries to compensate for horizontal movements and you may therefore
decide to turn it off during panning. The image stabilizer cannot be turned off when
the program selector is set to [.
Open the menu and select [CAMERA SET UP]. Select [IMAGE S. i], set itto [OFF] and close the menu.
i disappears.
❍ We recommend turning off the image stabilizer when you mount thecamcorder on a tripod.
❍ The image stabilizer is designed to compensate a normal degree of camcordershake.
❍ The image stabilizer cannot be used in CARD CAMERAmode.
❍ The image stabilizer might not be as effective in Low Light, Night and SuperNight (MV650i) mode.
MV630iMV650i
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
IMAGE S. ••ONCAMERA SET UP( 43)
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 68
69
Usin
g th
e Full R
ang
e o
f Features
E
Recording With the Self-Timer
1. Press the (self-timer) button.
“ ” appears.
When recording movies
2. Press the start/stop button.
The camcorder starts recording after a 10-second countdown (2
seconds when using the wireless controller). The count down
appears on the screen.
3. Press the start/stop button to stop recording.
The camcorder returns to record pause mode.
When recording still images
2. Press the PHOTO button.
• The camcorder adjusts the focus 2 seconds before recording
begins. F flashes in white and turns green when focus and
exposure are adjusted.
• The camcorder records the still image for approx. 6 seconds
and returns to record pause mode (MV650i/MV630i: In CARD CAMERA mode, it
displays the still image when recording is complete).
❍ To cancel the self-timer, press the (self-timer) button, start/stop button(when recording movies) or PHOTO button (when recording still images).
❍ The self-timer will be canceled when you turn off the camcorder.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
DATACODE
OFFOFF
(VCR)(VCR)PLAYPLAY
CAMERA
PHOTO
(self-timer)button
PHOTO button
Start/stop button
Start/stop button
PHOTObutton
SELF T. button
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 69
70
Usi
ng
th
e Fu
ll R
ang
e o
f Fe
atu
res
E
Audio Recording
Changing the Audio ModeYou can record sound in two audio modes—16-bit and 12-bit. The 12-bit mode records
sound on two channels (stereo 1), leaving 2 channels free (stereo 2) for adding new
sound later. Select the 16-bit mode for higher sound quality.
* MV650i/MV630i/MV600i only.
Open the menu and select [AUDIO SET UP]. Select [AUDIO MODE], set it to[16bit] and close the menu.
“16 bit” appears for approximately 4 seconds.
For adding new sound, see Audio Dubbing ( 95).
Recording with an External MicrophoneYou can use an external microphone for
recording. Almost all stereo microphones with
a plug diameter of 3.5 mm can be connected
to the MIC terminal. Use a microphone with a
built-in power supply (condenser
microphone).
❍ The audio level differs from that of the built-in microphone.❍ Be careful with long microphones as they may appear in the picture.❍ See also Using the DM-50 Microphone ( 73).❍ Do not use a microphone cable longer than 3 m to avoid electromagnetic
interference.
MV650i
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)*CAMERA
AUDIO MODE••12bitAUDIO SET UP
MIC
( 43)
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 70
71
Usin
g th
e Full R
ang
e o
f Features
Wind ScreenYou can reduce the wind noise when recording in windy places.
Open the menu and select [AUDIO SET UP]. Select [WIND SCREEN], set itto [ON] and close the menu.
“WS ON” appears when you turn the wind screen on.
❍ Low sound may be reduced together with the wind noise. We recommendturning off the wind screen for normal recordings.
❍ The wind screen function cannot be turned on/off during recording. ❍ The wind screen function can also be used for audio
dubbing (when [AUDIO DUB.] is set to [MIC. IN] in the [AUDIO SET UP]submenu).
❍ The wind screen function cannot be used when an external microphone isconnected to the MIC terminal (MV650i: or when the DM-50 Microphone isattached to the advanced accessory shoe).
MV600iMV630iMV650i
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA E
WIND SCREEN•OFFAUDIO SET UP( 43)
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 71
72
Usi
ng
th
e Fu
ll R
ang
e o
f Fe
atu
res
E
Using the VL-3 Video Light (Optional)This video light enables you to record brightly in colour even in dark places. This VL-3
Video Light attaches to the camcorder’s advanced accessory shoe for cable-free
operation and is powered by the camcorder’s power supply.
Refer also to the VL-3 Video Light instruction manual.
❍ Always turn off the camcorder before attaching/removing the video light.❍ Do not touch or place flammable material or plastic close to the lamp or the
surrounding parts during or immediately after use; they become very hot. ❍ Do not look directly at the lamp while the video light is on.❍ Do not carry the camcorder by the video light.
1. Slide the video light into theaccessory shoe until it clicks.
2. Tighten the fastening screw.
Be careful that the video light does not come
off when tightening the screw.
3. Set the camcorder to CAMERA orCARD CAMERA mode.
4. Turn the video light’s power switchto AUTO or ON.
• (Connection) appears.
• ON: The video light stays on.
• AUTO: The video light turns on and off
automatically.
MV650i
LOCK
LOCK
LOCK
ON
OFF
AUTO
LOCK
q
w
e
r
OFF
(VCR)(VCR)PLAY
CAMERA
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 72
73
Usin
g th
e Full R
ang
e o
f Features
E
Using the DM-50 Microphone (Optional)The high sensitive Directional Stereo Microphone DM-50 attaches to the
advanced accessory shoe for cable-free operation and is powered by the camcorder’s
power supply. Use it for recording or dubbing audio.
Refer also to the DM-50 Microphone instruction manual.
❍ Always turn the camcorder off before attaching/removing the microphone.❍ Do not connect any microphone to the MIC terminal when the DM-50
Microphone is connected.❍ Do not carry the camcorder by the microphone.
1. Slide the microphone into theaccessory shoe until it clicks.
2. Tighten the fastening screw.
Be careful that the microphone does not
come off when tightening the screw.
3. Set the camcorder to CAMERA orCARD CAMERA mode.
(Connection) appears.
4. Set the microphone’s directivityswitch.
• SHOTGUN: For recording clear sound from
the front (monaural).
• STEREO 1: For recording sound from the
front and surrounding area.
• STEREO 2: For recording surrounding
sound in a wider range than in
STEREO 1.
MV650i
q
e
w
r
OFF
(VCR)PLAYPLAY
CAMERACAMERA
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 73
74
Usi
ng
th
e Fu
ll R
ang
e o
f Fe
atu
res
E
Adjusting the Focus ManuallySome subjects may not be suitable for autofocus. In such case, focus manually.
Autofocus may not work well on the following subjects:
1. Set the program selector to Q.
2. Adjust the zoom.
When you operate the zoom after adjusting the focus, the
subject may not stay in focus. Adjust the zoom before the focus.
3. Press the FOCUS button.
“MF” appears in light blue.
4. Turn the selector dial to adjust the focus.
• Turn the selector dial up or down until the image appears
focused.
• If “AE ±0” appears in light blue, focus cannot be adjusted.
Press the FOCUS button again to display “MF” in light blue.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
FOCUS
Subjects with Reflective surfaces low contrast Fast Moving Subjects Horizontal Stripes
(e.g. White Wall)
Through dirty or wet windows Different Distances Dark Subjects Night Scenes
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 74
75
Usin
g th
e Full R
ang
e o
f Features
5. Press the FOCUS button to return to autofocus.
The setting resets to autofocus when you switch the program selector to [.
Infinity FocusUse this function when you wish to focus on faraway subjects such as mountains or
fireworks.
Press the focus button more than 3 seconds in step 3.
“MF ∞” appears. When you operate the zoom or turn the selector dial when “MF ∞” is
displayed in light blue, “∞” disappears and the camcorder changes to manual focus.
E
FOCUS
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 75
76
Usi
ng
th
e Fu
ll R
ang
e o
f Fe
atu
res
E
Adjusting the AE ShiftYou can adjust the AE (auto exposure) function to lighten or darken the image. This
allows you to compensate for backlit or overexposed scenes. Available Levels: –2 to +2,
in 0.25 intervals (excluding –1.75 and +1.75).
1. Set the program selector to Q.
2. Set the program AE mode to Auto, Sports, Portrait, LowLight or Low Light Plus (MV650i) mode.
3. Press the AE SHIFT button.
“AE ±0” appears in light blue.
4. Turn the selector dial to adjust the AE shift level.
• Turn the selector dial up to lighten the image and down to
darken the image.
• If “MF” is displayed in light blue, AE shift cannot be adjusted.
Press the AE SHIFT button again to display “AE ±0” in light blue.
❍ The camcorder retains the setting even if you turn it off or change the programAE mode.
❍ The camcorder resets to the auto setting when you switch the programselector to [.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
AE SHIFT
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 76
77
Usin
g th
e Full R
ang
e o
f Features
E
Setting the Shutter SpeedIn the Auto mode, you can adjust the shutter speed manually to make stable shots
of fast moving subjects.
1. Set the program selector to Q.
2. Set the program AE mode to the Auto mode.
3. Open the menu and select [CAMERA SET UP].
4. Select [SHUTTER].
5. Select the shutter speed and press the selector dial.
6. Close the menu.
❍ Do not point the camcorder directly at the sun when the shutter speed is set to1/1000 or higher.
❍ The image may flicker when recording with high shutter speeds.❍ The setting resets to the auto setting when you switch the program selector to[, or change the program AE mode.
❍ If the shutter speed is set to 1/500 or higher in CAMERAmode and you switch to CARD CAMERA mode, it automatically changes to1/250.
MV630iMV650i
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
SHUTTER•••••AUTOCAMERA SET UP
CAMERA Mode
CARD CAMERA Mode
AUTO AUTO1/50 1/50
1/120 1/1201/250 1/2501/500
1/10001/2000
MV630iMV650i
( 43)
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 77
78
Usi
ng
th
e Fu
ll R
ang
e o
f Fe
atu
res
❍ Guidelines for Recording with High Shutter Speeds:- Outdoor sports such as golf or tennis: 1/2000
- Moving objects such as cars or roller coasters: 1/1000,1/500 or 1/250
- Indoor sports such as basketball: 1/120
E
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 78
79
Usin
g th
e Full R
ang
e o
f Features
E
Setting the White BalanceThe camcorder’s auto white balance system adjusts the colours to appear natural for
different lighting conditions. However, you can use the preset modes to reproduce
colours more accurately, or set a custom white balance to obtain the optimal setting.
❍ When the program selector is set to [, white balance is preset to [AUTO].Indoor, outdoor and custom white balance cannot be selected.
❍ The camcorder retains the setting even if you turn it off.❍ When you have set the custom white balance:
- Reset the white balance when the lighting condition changes.- Turn off the digital zoom.
❍ Setting the white balance manually may provide better results in the followingcases: - Changing lighting conditions- Close-ups- Subjects in a single colour (sky, sea or forest)- Under mercury lamps or certain types of fluorescent lights
❍ Use the T Indoor or U Outdoor mode in the following cases:T Indoor:- Changing lighting condition- Under video light- Under sodium lampsU Outdoor:- For night scenes or fireworks- Sunrise or sunset* Use the auto setting for normal outdoor scenes.
Zoom lever
Program selector
Selector dial
White sheet or paper
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 79
80
Usi
ng
th
e Fu
ll R
ang
e o
f Fe
atu
res
For T (Indoor) or U (Outdoor) Setting:
1. Set the program selector to Q.
2. Open the menu and select [CAMERA SET UP].
3. Select [WHITE BAL.].
4. Select T (indoor) or U (outdoor).
T or U appears.
5. Close the menu.
For Custom White Balance:
1. Set the program selector to Q.
2. Open the menu and select [CAMERA SET UP].
3. Select [WHITE BAL].
4. Point the camcorder at a white object (such as a sheet of paper), zoomin until it fills the whole screen and select [SET W].
•W flashes and stops flashing when settings is complete.
• Depending on the light source, W may keep flashing. The result will still be better
than with the auto setting.
5. Close the menu.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
E WHITE BAL.••AUTO CAMERA SET UP( 43)
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 80
81
Usin
g th
e Full R
ang
e o
f Features
E
Magnifying the Image The playback image can be magnified by 2 times.
1. Move the zoom lever toward T.
• The image is magnified by 2 times.
• A frame appears indicating the position of the enlarged part.
2. Move the image.
• Turn the selector dial to move the image to the right and left,
or up and down. Pressing the selector dial switches between
the directions.
• To cancel the magnification, move the zoom lever toward W.
Movies played back from a memory card cannot be magnified.MV650i
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 81
82
Usi
ng
th
e Fu
ll R
ang
e o
f Fe
atu
res
E
Displaying the Data Code Once date and time are set, the camcorder maintains a data code containing
recording date and time and other camera data such as shutter speed and exposure
(f-stop). (MV650i/MV630i: Only date and time appear when playing back a memory
card).
❍ The data code display turns off when you turn the camcorder off.❍ The data code may not be displayed if a recording made with this camcorder is
played back on a different digital camcorder.❍ The data code cannot be displayed in frame advance/reverse playback. Camera
data may not appear in some special playback modes. ❍ When the TV screen displays are hidden ( 133), the displays still appear on
the LCD screen. If you turn on the data code, displays other than the datacode will disappear from the LCD screen.
Available Data Code Combinations (in PLAY (VCR) mode):
Date/Time Camera dataDate/Time & Camera data
Time
Date & Time
Date
DATA CODE(tape only)
D/TIME SEL.
F1.81/250
F1.81/250
1.JAN.2003
12:00:00 PM
12:00 PM 1.JAN.2003
F1.81/250
F1.81/250 1.JAN.2003
F1.81/25012:00:00 PM
F1.81/25012:00 PM 1.JAN.2003
DATA CODE button
MENU button
Selector dial
Controller buttons
MENU button
DATA CODE button
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 82
83
Usin
g th
e Full R
ang
e o
f Features
Selecting the Date/Time Display Combination
Open the menu and select [DISPLAY SET UP]. Select [D/TIME SEL.], set it to[DATE] or [TIME] and close the menu.
Selecting the Data Code Display Combination
Open the menu and select [DISPLAY SET UP]. Select [DATA CODE], set it to[DATE/TIME], [CAMERA DATA] or [CAM. & D/T] and close the menu.
Displaying the Data Code
Press the DATA CODE button.
Only date and time appear in CARD PLAY (VCR) mode.
Six-Second Auto DateDate and time appear for 6 seconds when you begin playback, or to indicate that date
or time zone has changed.
Open the menu and select [DISPLAY SET UP]. Select [6SEC.DATE], set it to[ON] and close the menu.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
ED/TIME SEL.•DATE & TIMEDISPLAY SET UP
DATA CODE•••DATE/TIMEDISPLAY SET UP
6SEC.DATE•••OFFDISPLAY SET UP
( 43)
( 43)
( 43)
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 83
84
Usi
ng
th
e Fu
ll R
ang
e o
f Fe
atu
res
E
Photo Search/Date SearchYou can search for a still image recorded
anywhere on the tape with the photo search
function, or locate the change of the
date/time zone with the date search function.
1. Press the SEARCH SELECT button to choose betweenphoto search and date search.
“PHOTO SEARCH” or “DATE SEARCH” appears.
2. Press the + or - button to begin searching.
• Press the + button to search forward and the - button to
search backward.
• Press more than once to search for further still images or date
changes (up to 10 times).
• Press the + or - button to change the search direction.
• Press the 3 (stop) button stop searching.
❍ Photo search: A still image recorded very close to the point you start the searchmay not be detected.
❍ Date search: A recording of longer than a minute per date/area is required.❍ Date search: Playback may start slightly before or after the date change.❍ Date search may not function if the data code is not correctly displayed.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
REW PLAY
STOP
FFZERO SETMEMORY
12bitAUDIO OUT
SEARCH SELECTDATA CODE
INDEX SLIDE SHOW CARD
REW PLAY
STOP
FFZERO SETMEMORY
12bitAUDIO OUT
SEARCH SELECTDATA CODE
INDEX SLIDE SHOW CARD
SEARCH SELECT button
Search buttons
STOP 3 button
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 84
85
Usin
g th
e Full R
ang
e o
f Features
E
Returning to a Pre-marked PositionIf you wish to return to a particular scene
later, mark the point with the zero set
memory and the tape will stop at that point
when you rewind/fast forward the tape.
1. Press the ZERO SET MEMORY button at the pointyou wish to return to later.
• “0:00:00 ” appears.
• To cancel, press the ZERO SET MEMORY button again.
2. When you have finished playback, fast forward orrewind the tape.
• RTN 1 or ` RTN appears.
• The tape stops automatically at “0:00:00”.
• The tape counter changes to time code.
❍ Time code and tape counter display may not match accurately.❍ The zero set memory may not function correctly when blank sections exist on
the tape. ❍ If you remove the tape, the zero set memory is cancelled and the counter
display shows the time code.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
REW PLAY
STOP
FFZERO SETMEMORY
12bitAUDIO OUT
SEARCH SELECTDATA CODE
INDEX SLIDE SHOW CARD
ZERO SETMEMORYbutton
REW ` button
PLAY e buttonFF 1 button
STOP 3 button
3_D73PAL_E(43-85) 02.12.26 9:26 PM Page 85
86
Edit
ing
E
Recording to a VCR or Digital Video DeviceYou can copy your recordings by connecting the camcorder to a VCR or a digital video
device. If you connect a digital video device, you can copy recordings with virtually no
generation loss in image and sound quality.
When connecting a VCR:❍ Make sure that “H” is not displayed on the screen. If “H” is displayed, change
the setting ( 37).❍ The quality of the edited tape will be slightly lower than that of the original.When connecting a digital video device:❍ You can connect only one device to the camcorder with the DV cable.❍ Blank sections may be recorded as anomalous picture.❍ If the picture does not appear, reconnect the DV cable or turn the camcorder
off and back on again.
Example: Recording to a VCR
1. Connect the camcorder to the VCR.See Playing Back on a TV Screen ( 39).
2. Set the camcorder to PLAY (VCR) mode and load a recorded cassette.
3. Connected device: Load a blank cassette and set the device to recordpause mode.
4. Locate the scene you wish to copy and pause playback shortly beforethe scene.
5. Play back the tape.
6. Connected device: Begin recording when the scene you wish to copyappears. Stop recording when copying is complete.
7. Stop playback.
CARD CAMERACARD CAMERAPLAY (VCR)CAMERA
4_D73PAL_E(86-98) 02.12.26 9:28 PM Page 86
87
Editin
g
E
Connecting a Digital Video Device
Refer also to the instruction manual of the digital video device.
Side with an arrow
4 pin – 4 pin: CV-150F DV Cable (optional)4 pin – 6 pin: CV-250F DV Cable (optional)
Signal flow
4_D73PAL_E(86-98) 02.12.26 9:28 PM Page 87
88
Edit
ing
ERecording from Analog Video Devices (VCR, TV or Camcorder)You can record videos or TV programs from a VCR or analog camcorder on the tape in
the camcorder.
❍ Anomalous signals sent from the connected device may be recorded asanomalous picture (although it may not appear so on the screen), or it may notbe recorded at all.
❍ You cannot record from tapes with copyright protective signals.❍ Headphones cannot be used during analog line-in recording. If the
AV/headphones terminal set to [PHONES H], it will automatically switch to [AV].❍ When connecting to a TV/video with SCART terminal, use a SCART adapter
with input capability (commercially available). The SCART Adapter PC-A10 isfor output only.
1. Connect the camcorder to the analog video device.
See Playing Back on a TV Screen ( 39).
2. Set the camcorder to PLAY (VCR) mode and load a blank cassette.
3. Connected device: Load the recorded cassette.
4. Press the REC PAUSE button on the wirelesscontroller.
In record pause mode and during recording, you can check the
picture on the screen.
5. Connected device: Play back the tape.
6. Press the PAUSE a button on the wireless controllerwhen the scene you wish to record appears.
7. Press the STOP 3 button on the wireless controller tostop recording.
• Press the PAUSE a button on the wireless controller to pause
recording.
• Press the PAUSE a button again to restart recording.
8. Connected device: Stop playback.
CARD CAMERACARD CAMERAPLAY (VCR)CAMERA
MV600iMV630iMV650i
WIRELESS CONTROLLER WL-D79
AV INSERT AV DV REMOTE SET
RECPAUSE
REW
PAUSE
AV INSERT AV DV REMOTE SET
SLOW 2
PLAY
STOP
FFZERO SETMEMORY
12bitAUDIO OUT
AUDIO DUB.
REW
PAUSE
AV INSERT AV DV REMOTE SET
SLOW 2
PLAY
STOP
FFZERO SETMEMORY
12bitAUDIO OUT
AUDIO DUB.
4_D73PAL_E(86-98) 02.12.26 9:28 PM Page 88
89
Editin
g
ERecording from Digital Video Devices (DV Dubbing)You can record from other digital video devices equipped with a DV terminal with
virtually no loss in picture and sound quality.
❍ When recording from digital video devices, make sure that “AV \ DV” is notdisplayed on the screen. If “AV \ DV” is displayed, change the setting ( 92).
❍ Anomalous signals sent from the connected device may be recorded asanomalous picture (although it may not appear so on the screen), or it may notbe recorded at all.
❍ Copyright protected signals cannot be recorded.❍ Blank sections may be recorded as anomalous picture.❍ If the picture does not appear, reconnect the DV cable or turn the camcorder
off and back on again.
❍ You can connect only one device with the DV cable.❍ You can use the camcorder for playback and recording without reconnecting
the DV cable.
1. Connect the camcorder to the digital video device.
See Connecting a Digital Video Device ( 87).
2. Set the camcorder to PLAY (VCR) mode and load ablank cassette.
“DV IN” appears.
3. Connected device: Load the recorded cassette.
4. Press the REC PAUSE button on the wireless controller.
In record pause mode and during recording, you can check the picture on the screen.
5. Connected Device: Play back the tape.
6. Press the PAUSE a button on the wireless controllerwhen the scene you wish to record appears.
7. Press the STOP 3 button on the wireless controller tostop recording.
• Press the PAUSE a button on the wireless controller to pause
recording.
• Press the PAUSE a button again to restart recording.
8. Connected Device: Stop playback.
CARD CAMERACARD CAMERAPLAY (VCR)CAMERA
MV600iMV630iMV650i
WIRELESS CONTROLLER WL-D79
AV INSERT AV DV REMOTE SET
RECPAUSE
REW
PAUSE
AV INSERT AV DV REMOTE SET
SLOW 2
PLAY
STOP
FFZERO SETMEMORY
12bitAUDIO OUT
AUDIO DUB.
REW
PAUSE
AV INSERT AV DV REMOTE SET
SLOW 2
PLAY
STOP
FFZERO SETMEMORY
12bitAUDIO OUT
AUDIO DUB.
4_D73PAL_E(86-98) 02.12.26 9:28 PM Page 89
90
Edit
ing
Concerning CopyrightCopyright PrecautionCertain pre-recorded video tapes, films and other materials, as well as some television
programmes are copyrighted. Unauthorised recording of these materials may violate
copyright protection laws.
Copyright Signals During playback: If you try to play back a tape that contains copyright control signals
for protection of software, “COPYRIGHT PROTECTED PLAYBACK IS RESTRICTED”
appears for a few seconds and the camcorder displays a blank blue screen. You cannot
playback the contents of the tape.
During recording: If you try to record from software that contains copyright control
signals for protection of software, “COPYRIGHT PROTECTED DUBBING RESTRICTED”
appears. You cannot record the contents of the software.
You cannot record copyright protection signals to a tape using this camcorder.
E
4_D73PAL_E(86-98) 02.12.26 9:28 PM Page 90
91
Editin
g
EConverting Analog Signals into DigitalSignals (Analog-Digital Converter)By connecting the camcorder to a VCR or 8mm video camcorder, you can convertanalog video/audio signals to digital signals and output the digital signals via the DVterminal. The DV terminal serves as output terminal only.
❍ Headphones cannot be used during analog-digital conversion. ❍ Unload the tape from the camcorder.❍ Turn off all devices before starting the connections.❍ Depending on the signal sent from the connected device, the conversion from
analog to digital signals might not work properly (e.g., signals that includecopyright protective signals or anomalous signals such as ghost signals, etc.)
❍ When connecting to a TV/video with SCART terminal, use a SCART adapterwith input capability (commercially available). The SCART Adapter PC-A10 isfor output only.
We recommend powering the camcorder from a household power source.
Connecting the DevicesThis illustration shows how to connect using a S-video cable. You can also connect theyellow plug of the stereo video cable to the VIDEO terminal. Refer also to theinstruction manual of the connected device.
MV600iMV630iMV650i
R
L
S
AV
DV
OUTPUT
VIDEO
S(S1)-VIDEO
AUDIO
Signal flow
Signal flow
Signal flow
S-150 S-video Cable (optional)
STV-250N Stereo Video Cable (supplied)
4 pin – 4 pin: CV-150F DV Cable (optional)4 pin – 6 pin: CV-250F DV Cable (optional)
4_D73PAL_E(86-98) 02.12.26 9:28 PM Page 91
92
Edit
ing
Turning On the Analog-Digital Converter
Press the AV \ DV button on the wireless controller.
OR
Open the menu and select [VCR SET UP]. Select [AV \ DV OUT], set it to[ON] and close the menu.
❍ For normal use, set [AV \ DV OUT] to [OFF] (so that “AV \ DV” does notappear on the screen). If it is set to [ON], digital signals cannot be input via thecamcorder’s DV terminal.
❍ Depending on the software and the specifications of your computer, you maynot be able to transfer converted signals via the DV terminal.
CARD CAMERACARD CAMERAPLAY (VCR)CAMERA
E
AV DV OUT••OFFVCR SET UP( 44)
4_D73PAL_E(86-98) 02.12.26 9:28 PM Page 92
93
Editin
g
EReplacing Existing Scenes (AV Insert)You can insert and replace images/audio on the tape of the camcorder with
images/audio from other video devices connected via AV terminal or DV terminal.
❍ Make sure that “H” is not displayed on the screen. If “H” is displayed, changethe setting ( 37).
❍ You cannot insert from a TV program when the synchronised signals aredistorted.
Camcorder:❍ Use only tapes recorded in SP mode.❍ AV insert will stop if the camcorder detects a blank section or a section not
recorded in SP mode on the tape.Connected device:❍ Use only tapes without blank sections.❍ AV insert may not work correctly if the tape has a blank section or changes in
the recording mode.❍ AV insert cannot be performed when the quality of the recording is poor, or
during special playback such as fast forward, rewind, playback pause, slowplayback etc.
MV600iMV630iMV650i
Playback tape
Tape in thecamcorderbefore inserting
Tape in thecamcorder afterinserting
Scene to be inserted
Insert start Insert end
Inserted scene
4_D73PAL_E(86-98) 02.12.26 9:28 PM Page 93
94
Edit
ing
Example: AV Insert from a VCR
1. Connect the camcorder to the VCR.
See Playing Back on a TV Screen ( 39).
2. VCR: Load a recorded cassette. Locate the scene you wish to insert andpause playback shortly before the scene.
3. Set the camcorder to PLAY (VCR) mode and load a recorded cassette.
Make sure the tape-protect switch is set to allow recording.
4. Locate the scene you wish to replace and pause playback shortly beforethe scene.
You can use the playback buttons on the camcorder or the special playback buttons on
the wireless controller.
5. Press the AV INSERT button on the wirelesscontroller.
“AV INSERT” and “2a” appear.
6. VCR: Play back the tape.
7. Press the PAUSE a button on the wireless controllerwhen the scene you wish to insert appears.
8. Press the STOP 3 button on the wireless controllerto stop inserting.
Press the PAUSE a button on the wireless controller to pause
inserting.
9. VCR: Stop playback.
Set the zero set memory at the end of the scene you wish to replace. Thecamcorder will automatically stop AV insert at that point.
CARD CAMERACARD CAMERAPLAY (VCR)CAMERA
E
PAUSE
AV INSERT AV DV REMOTE SET
SLOW 2
STOP
RECPAUSE
12bitAUDIO OUT
AUDIO DUB.
REW
PAUSE
AV INSERT AV DV REMOTE SET
SLOW 2
PLAY
STOP
FFZERO SETMEMORY
12bitAUDIO OUT
AUDIO DUB.
REW
PAUSE
AV INSERT AV DV REMOTE SET
SLOW 2
PLAY
STOP
FFZERO SETMEMORY
12bitAUDIO OUT
AUDIO DUB.
4_D73PAL_E(86-98) 02.12.26 9:28 PM Page 94
95
Editin
g
E
Audio DubbingYou can add sound from audio devices (AUDIO IN) or with the built-in or an external
microphone (MIC. IN). With the MV600, audio dubbing can only be performed with
the built-in or an external microphone (MIC. IN).
❍ Use only tapes recorded in SP mode 12-bit audio sound with this camcorder.Audio dubbing will stop if the tape has a blank section or a section recorded inLP mode, 16-bit or 12-bit 4-channel sound. In above case, create a copy in SPmode 12-bit audio sound using the analog line-in function.
❍ Do not connect/disconnect any cable to/from the camcorder while dubbing.❍ You cannot use the DV terminal for audio dubbing.❍ If you add sound to a tape not recorded with this camcorder, sound quality
may decrease.❍ Sound quality may decrease when you add sound to the same scene for more
than 3 times.
Connecting an Audio Device
❍ Make sure that “H” is not displayed on the screen. If “H” is displayed, changethe setting ( 37).
❍ You can monitor the picture on the LCD screen or a TV connected via the S-video terminal, and check the sound with the built-in speaker.
MV600iMV630iMV650i
AV
R
LSignal flow
STV-250N Stereo Video Cable (supplied)
4_D73PAL_E(86-98) 02.12.26 9:28 PM Page 95
96
Edit
ing
E
Using a Microphone
❍ When using the built-in microphone: do not connect any cables to themicrophone terminal or the accessory shoe.
❍ When using an external microphone: Connect it to the microphone terminal.❍ When using the DM-50 Microphone: Do not connect any cables to the
microphone terminal.❍ When you connect a TV via the S-video terminal, you can check the picture on
the TV screen and the sound with headphones connected to the camcorder.When you connect a TV via the AV terminal, you can check the picture on theTV screen but you cannot check the sound with headphones.
Dubbing
1. Set the camcorder to PLAY (VCR) mode and load a recorded cassette.
2. Open the menu and select[AUDIO SET UP]. Select [AUDIO DUB.], set it to[AUDIO IN] or [MIC. IN] and close the menu.
3. Locate the scene you wish audio dubbing to start.
4. Press the PAUSE a button on the wireless controller.
5. Press the AUDIO DUB. button on the wirelesscontroller.
• “AUDIO DUB.” and appear.
• If the optional DM-50 microphone is attached,
(Connection) appears.
6. Press the PAUSE a button on the wireless controllerto begin dubbing.
• Audio device: Begin playback.
• Microphone: Direct your voice to the microphone.
MV600iMV630iMV650i
MV650i
MV600iMV630iMV650i
CARD CAMERACARD CAMERAPLAY (VCR)CAMERA
MV650i
PAUSE
AV INSERT AV DV REMOTE SET
SLOW 2
STOP
RECPAUSE
12bitAUDIO OUT
AUDIO DUB.
REW
PAUSE
AV INSERT AV DV REMOTE SET
SLOW 2
PLAY
STOP
FFZERO SETMEMORY
12bitAUDIO OUT
AUDIO DUB.
MIC
4_D73PAL_E(86-98) 02.12.26 9:28 PM Page 96
97
Editin
g
E
7. Press the STOP 3 button on the wireless controllerto stop dubbing.
Audio device: Stop playback.
Set the zero set memory at the end of the scene you wish to dub audio. Thecamcorder will automatically stop audio dubbing at that point.
Playing Back the Added SoundYou can select to play back Stereo 1 (original sound), Stereo 2 (added sound), or adjust
the balance of both sounds.
1. Open the menu and select [AUDIO SET UP], select a setting and closethe menu.
• STEREO 1: Plays back the original sound.
• STEREO 2: Plays back the added sound.
• MIX/FIXED: Plays back stereo 1 and stereo 2 in the same level.
• MIX/VARI.: Plays back stereo 1 and stereo 2. The mix balance can be adjusted.
2. If you have selected [MIX/VARI.], adjust the mix level: Open the menuand select [AUDIO SET UP]. Select [MIX BALANCE], adjust the balancewith the selector dial and close the menu.
Turn the selector dial down to increase the volume of Stereo 1 and up to increase the
volume of Stereo 2.
❍ The camcorder resets to [STEREO 1] when you turn the camcorder off.However, the mix balance is memorised by the camcorder.
❍ You can also press the 12bit AUDIO OUT button on the wireless controller toselect the audio output. However, the mix balance can only be adjusted in themenu.
CARD CAMERACARD CAMERAPLAY (VCR)CAMERA
MV600iMV630iMV650i
REW
PAUSE
AV INSERT AV DV REMOTE SET
SLOW 2
PLAY
STOP
FFZERO SETMEMORY
12bitAUDIO OUT
AUDIO DUB.
MENU button
Selector dial
12bit AUDIOOUT button
12bit AUDIO•STEREO1 AUDIO SET UP( 43)
4_D73PAL_E(86-98) 02.12.26 9:28 PM Page 97
98
Edit
ing
E
Connecting to a Computer Using a DV (IEEE1394) CableYou can transfer recordings to a computer equipped with a DV (IEEE1394) terminal or
IEEE1394 capture board (optional software required).
Use the optional CV-150F (4 pin–4 pin) or CV-250F (4 pin– 6 pin) DV Cable.
❍ Do not disconnect the DV cable, or turn off the camcorder or computer whiledata is being transferred to the computer.
❍ Operation may not work correctly depending on the software and thespecifications/settings of your computer.
❍ We recommend powering the camcorder from a household power sourcewhile it is connected to the computer.
❍ Refer also to the instruction manual of the computer.Optional software required. Refer also to the instruction manual of the software.
❍ For transferring recordings from a memory card to thecomputer using a USB cable, see p. 128.
DV NETWORK SOLUTION DISK (Windows XP Users)Windows XP users can use the software on the supplied DV NETWORK SOLUTION
DISK to perform videoconference and file transfer over the Internet, or upload files
from the computer to the memory card and use the camcorder as card reader/writer.
The available functions depend upon the camcorder model and the networking
environment. For details, refer to the DV NETWORK SOLUTION DISK Software
Instruction Manual.
❍ Do not disconnect the DV cable, remove the memory card or turn off thecamcorder or computer while data is being transferred to the computer (whilethe camcorder’s card access indicator is flashing). Doing so may damage thememory card’s data.
❍ The image files on your memory card and the image files saved on the harddisk drive of your computer are your valuable, original data files. If you wish touse image files on your computer, be sure to make copies of them first,retaining the original.
MV630iMV650i
MV630iMV650i
DV
IEEE1394 (DV)terminal
DV Cable (optional)DV IN/OUTterminal
4_D73PAL_E(86-98) 02.12.26 9:28 PM Page 98
99
Usin
g a M
emo
ry Card
MV
630iM
V650i
E
Inserting and Removing the Memory CardThe chapter Using a Memory Card ( 99 - 132) refers to functions of the MV650i and
MV630i only.
You can use SD Memory Cards or a
commercially available MultiMediaCards with
this camcorder. The SD Memory Card has a
protect switch for prevent accidental erasure.
❍ This camcorder is compatible with SD Memory Cards or MultiMediaCards only.Do not use any other types of memory cards.
❍ Turn off the camcorder before inserting or removing the memory card.Otherwise it may result in data damage.
❍ Do not touch the memory card terminals.❍ If you use memory cards other than the supplied one, make sure to format
them with the camcorder ( 127).❍ For instructions on how to connect the camcorder to the computer, see
Connecting to a Computer using a USB Cable ( 128).
Inserting the Card1. Turn off the camcorder.
2. Open the cover.
3. Insert the memory card all the wayinto the memory card slot.
4. Close the cover.
Do not close the cover forcefully without
having the card correctly inserted.
Removing the CardDo not forcefully remove the memory card without first pushing it in.
1. Turn off the camcorder.
Make sure that the card access indicator is not
flashing.
2. Open the cover.
3. Push the memory card to release it.Remove the memory card.
4. Close the cover.
Terminals
Card access indicator
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 99
100
Usi
ng
a M
emo
ry C
ard
MV
630i
MV
650i
E
Selecting the Image Quality/Size
Changing the Still Image QualityYou can choose between Superfine, Fine and Normal.
Open the menu and select [CARD SET UP]. Select [SI QUALITY], set it to[SUPER FINE] or [NORMAL] and close the menu.
Changing the Still Image SizeYou can choose between 1024 × 768 pixels and 640 × 480 pixels.
Open the menu and select [CARD SET UP]. Select [SI SIZE], set it to [640 ×480] and close the menu.
❍ Still images recorded in 1024 × 768 pixels may not be displayed correctly in acamcorder not supporting this size.
❍ Still images are compressed and recorded in the JPEG (Joint PhotographicExperts Group) format.
❍ Depending on subject and recording condition, changing the image qualitymay not show a significant difference.
❍ Estimated Capacity of a 8 MB Memory Card and File Size per Image:
These figures are approximate. They vary according to the recording conditionand the subject. Sample images already recorded on the supplied SD MemoryCard are to be included in the total number.
❍ Remaining Image Capacity:flashingin red: No cardin green: 6 or more imagesin yellow: 1 to 5 imagesin red: No more images
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
SI QUALITY••FINECARD SET UP
SI SIZE•••••1024×768CARD SET UP
Image Size
Image Quality
1024 × 768 640 × 480
No. of Images File Size per Image
File Size per ImageNo. of Images
Superfine 14 images 440 KB 35 images 175 KB
Fine 20 images 300 KB 52 images 120 KB
Normal 39 images 160 KB 86 images 65 KB
( 43)
( 43)
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 100
101
Usin
g a M
emo
ry Card
MV
630iM
V650i
E
❍ The indication may not decrease even though a recording has been made, ormay decrease by 2 images at once.
❍ All indicators are displayed in green when a memory card is played back.❍ The remaining image capacity indicates the number of still images,
even when movies are recorded.
Changing the Movie SizeYou can choose between 320 × 240 pixels and 160 × 120 pixels.
Open the menu and select [CARD SET UP]. Select [MOVIE SIZE], set it to[160 × 120] and close the menu.
❍ Movies are recorded in the Motion JPEG format.❍ Maximum continuous recording time:
File NumbersImages are automatically assigned file numbers from 0101 to 9900 and stored in
folders containing up to 100 images. Folders are assigned numbers from 101 to 998.
(The sample images on the supplied memory card are saved in the [100canon] folder.)
You can choose to use consecutive file numbers (CONTINUOUS) or to reset the file
number each time a different memory card is inserted (RESET). We recommend setting
the file numbers to CONTINUOUS.
CONTINUOUS The camcorder memorises the file number of the last image and assigns the
consecutive file number to the next image, even when a new memory card is inserted.
(If a higher file number already exists on the memory card, the consecutive number
will be assigned.) There will be no duplication of file numbers. This is useful for
organizing images on a computer.
RESETThe file number will be reset each time a new memory card is inserted, starting with
101-0101. If the memory card already contains image files, the consecutive file number
will be assigned.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
MV650i
MV650i
MOVIE SIZE••320×240CARD SET UP
320 × 240 10 sec. 2.7 MB 270 KB/sec.
160 × 120 30 sec. 2.7 MB 90 KB/sec.
Image Size Max. ContinuousRecording Time Total File Size File Size per Second
( 43)
5_D73PAL_E(99-132) 03.1.15 2:33 PM Page 101
102
Usi
ng
a M
emo
ry C
ard
MV
630i
MV
650i
E
To change the setting, open the menu and select [CARD SET UP]. Select[FILE NOS.], set it to [RESET] and close the menu.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
FILE NOS.•••CONTINUOUSCARD SET UP
101-0101101
101-0102
101-0104101 101-0101101
101-0103
CONTINUOUS RESET
When you record 3 images on the supplied memory card.
When you replace the memorycard and record an image.
( 43)
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 102
103
Usin
g a M
emo
ry Card
MV
630iM
V650i
E
Recording Still Images on a Memory CardYou can record still images with the
camcorder, from a tape in the camcorder
( 104), or from devices connected via the
DV terminal or AV terminal ( 105).
❍ Do not turn off the camcorder, disconnect the power source or remove thememory card while the card access display (<<< or >>>) in the upper rightcorner of the screen or the card access indicator is flashing. Doing so couldresult in data damage.
❍ When you are using a SD Memory Card, make sure that the protect switch isset to allow recording.
Make sure to insert a memory card with enough remaining capacity.
Recording with the Camcorder
1. Set the camcorder to CARD CAMERA mode.
The remaining image capacity and other information appear.
2. Press the PHOTO button halfway.
• F flashes in white and turns green when focus is adjusted.
• Exposure is locked.
• When you press the PHOTO button on the wireless controller,
recording starts immediately.
3. Press the PHOTO button fully.
• You hear a shutter sound, and the screen appears as if a
shutter has been released.
• The card access indicator flashes.
• The still image shown on the screen will be recorded on the memory card.
To use the self-timer ( 69), press the (self-timer) button before step 2 andpress the PHOTO button fully.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
PHOTO
Card access indicator
PHOTO button
PHOTO
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 103
104
Usi
ng
a M
emo
ry C
ard
MV
630i
MV
650i
Recording from a Tape in the CamcorderYou can record images from a tape in the camcorder as still images on a memory card.
1. Set the camcorder to PLAY (VCR) mode.
2. Play back the tape.
3. Press the PHOTO button halfway when the scene you wish to recordappears.
• The camcorder pauses playback. The remaining image capacity and other information
appear.
• When you press the PHOTO button on the wireless controller, recording starts
immediately.
4. Press the PHOTO button fully.
• The card access indicator flashes.
• The still image shown on the screen will be recorded on the memory card.
• You can also record a still image by pressing the PHOTO button fully when the tape is
in playback pause mode.
❍ A still image recorded from an image in 16:9 format will be verticallycompressed.
❍ The data code of the still image will reflect the date and time it has beenrecorded on the memory card.
❍ There will be no shutter sound in PLAY (VCR) mode.❍ The image size of a still image recorded from a tape in the camcorder will be
640 × 480.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERAE
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 104
105
Usin
g a M
emo
ry Card
MV
630iM
V650i
E
Recording from Other Video Devices You can record images from devices connected via the S-video terminal or AV terminal
(analog line-in function), or via the DV terminal as still images on a memory card.
When recording via the AV terminal, make sure that “AV \ DV” is displayed onthe screen. When recording via the DV terminal, make sure that “AV \ DV” isnot displayed. Change the setting as necessary ( 92).
1. Connect the camcorder to the video device.
• S-video/AV terminal: See Playing Back on a TV Screen ( 39).
• DV terminal: See Connecting a Digital Video Device ( 87).
2. Set the camcorder to PLAY (VCR) mode.
If a cassette is loaded, make sure the tape is stopped.
3. Connected device: Load a recorded cassette and play back the tape.
4. Press the PHOTO button halfway when the scene you wish to recordappears.
• The still image, remaining image capacity and other information appear.
• When you press the PHOTO button on the wireless controller, recording starts
immediately.
5. Press the PHOTO button fully.
• The card access indicator flashes.
• The still image shown on the screen will be recorded on the memory card.
❍ A still image recorded from an image in 16:9 format will be verticallycompressed.
❍ The data code of the still image will reflect the date and time it has beenrecorded on the memory card.
❍ There will be no shutter sound in PLAY (VCR) mode.❍ The image size of a still image recorded from other video devices will be
640 × 480.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 105
106
Usi
ng
a M
emo
ry C
ard
MV
630i
MV
650i
E
Recording Panoramic Images (Stitch Assist Mode)You can shoot a series of overlapping images and merge them into one large
panoramic scene using the supplied software (PhotoStitch) on a computer.
When Recording in Stitch Assist Mode:PhotoStitch detects the overlapping portion of adjoining images and merges them. Try
to include a distinctive item (landmark, etc.) in the overlapping portion.
1. Set the camcorder to CARD CAMERA mode.
2. Press the button.
3. Select the direction with the CARD +/– button.
CARD + button: clockwise. CARD – button: anticlockwise.
4. Select the program AE mode and zoom on the subject.
Adjust focus and AE shift manually as necessary. Once the sequence has started, you
cannot change the program AE mode, AE shift, zoom or focus.
5. Press the PHOTO button to record the first image.
Direction and number of recorded images appear.
6. Record the second image so that it overlaps a portion of the first image.
• Minor discrepancies in the overlapped area can be corrected with the software.
• You can retake an image by pressing the CARD – button to return to the previous
image.
• A maximum of 26 images can be recorded.
7. Press the button after the last image.
For details on how to merge these images, refer to the DIGITAL
VIDEO SOLUTION DISK Software Instruction Manual.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
MIX/SLIDESHOW
PHOTO
MIX/SLIDESHOW
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 106
107
Usin
g a M
emo
ry Card
MV
630iM
V650i
E
❍ Compose each image so that it overlaps 30 to 50% of the adjoining image. Tryto keep the vertical misalignment within 10%.
❍ Do not include moving subject in the overlapping portion.❍ Do not try to stitch images that include both distant and close subjects. They
may appear warped or doubled up.
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 107
108
Usi
ng
a M
emo
ry C
ard
MV
630i
MV
650i
E
Recording Motion JPEG Movies on a Memory CardYou can record Motion JPEG movies with the camcorder, from a tape in the camcorder
( 109), or from devices connected via the AV terminal (analog line-in) or the DV
terminal ( 109).
❍ Do not turn off the camcorder, disconnect the power source or remove thememory card while the card access display (<<< or >>>) in the upper rightcorner of the screen or the card access indicator is flashing. Doing so couldresult in data damage.
❍ When you are using a SD Memory Card, make sure that the protect switch isset to allow recording.
❍ Do not load/unload a cassette during recording.
❍ Make sure to insert a memory card with enough remaining capacity.❍ The sound of a movie recorded on a memory card will be monaural.
Recording with the Camcorder
1. Set the camcorder to CARD CAMERA mode.
2. Press the start/stop button to begin recording.
You can record up to 10 seconds in 320 × 240 and up to 30
seconds in 160 × 120.
3. Press the start/stop button to stop recording.
The camcorder starts writing the movie on the memory card.
To use the self-timer, press the (self-timer) button before step 2 ( 69) andpress the start/stop button.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
MV650i
OFFOFF
(VCR)(VCR)PLAY
CAMERA
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 108
109
Usin
g a M
emo
ry Card
MV
630iM
V650i
Recording from a Tape in the CamcorderYou can record movies from a tape in the camcorder on a memory card.
1. Set the camcorder to PLAY (VCR) mode.
2. Play back the tape.
3. Press the start/stop button when the scene you wish to record appears.
You can record up to 10 seconds in 320 × 240 and up to 30 seconds in 160 × 120.
4. Press the start/stop to stop recording.
❍ A movie recorded from an image in 16:9 format will be vertically compressed.❍ The data code of the movie will reflect the date and time it has been recorded
on the memory card.
Recording from Other Video DevicesYou can record movies from devices connected via the S-video terminal or AV terminal
(analog line-in function), or via the DV terminal on a memory card.
1. Connect the camcorder to the video device.
• S-video/AV terminal: See Playing Back on a TV Screen ( 40).
• DV terminal: See Connecting a Digital Video Device ( 87).
2. Set the camcorder to PLAY (VCR) mode.
If a cassette is loaded, make sure the tape is stopped.
3. Connected device: Load a recorded cassette and play back the tape.
4. Press the start/stop button when the scene you wish to record appears.
You can record up to 10 seconds in 320 × 240 and up to 30 seconds in 160 × 120.
5. Press the start/stop button to stop recording.
❍ A movie recorded from an image in 16:9 format will be vertically compressed.❍ The data code of the movie will reflect the date and time it has been recorded
on the memory card.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA E
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 109
110
Usi
ng
a M
emo
ry C
ard
MV
630i
MV
650i
E
Playing Back a Memory CardYou can play back memory card images on the LCD screen, viewfinder screen, or on a
connected TV screen (see Playing Back on a TV Screen ( 39)).
You can display a single image (single image display 110), 6 at one time (index
screen 111), or one after another (slide show 111). Use the Card Jump function
to quickly locate an image without displaying them one by one ( 112).
❍ Images not recorded with this camcorder, uploaded from a computer (exceptthe sample images 131), edited on a computer and images whose filenames have been changed may not be played back correctly.
❍ Still images not recorded with this camcorder may not be printed correctly on aBubble Jet Printer with the direct print function.
❍ Do not turn off the camcorder, disconnect the power source or remove thememory card while the card access display (<<<) in the upper right corner ofthe screen or the card access indicator is flashing. Doing so could result in datadamage.
❍ Make sure to insert a memory card that contains images.❍ Only date and time will be displayed when pressing the DATA CODE button.❍ You can enlarge still images by 2 times during playback ( 81).
Single Image Display
1. Set the camcorder to CARD PLAY (VCR) mode.
• The last recorded image appears.
• Movies are displayed with the first scene as a still image indicated by “e/a”.
2. Press the CARD+/– button to move between images.
Press the CARD + button to display the next image and the
CARD – button to display the previous image.
3. To play back a movie, press the e/a button.
The last scene appears as a still image when playback is
complete.
MV650i
MV650i
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
FOCUS
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 110
111
Usin
g a M
emo
ry Card
MV
630iM
V650i
E
Index Screen
1. In single image display, press the (index screen)button.
• Up to 6 images appear.
• Movies are displayed with the first scene as a still
image indicated by “ ”.
2. Press the CARD +/– button to change the imageselection.
3. Move the mark to the image you wish to view.
• Turn the selector dial up to move to the next image and down
to move to the previous image.
• Turning the selector dial up on the last image displays the next
index screen. Turning the selector dial down on the first image
displays the previous index screen.
4. Press the (index screen) button.
The index screen is cancelled and the selected image appears in
single image display.
Slide Show
1. In single image display, press the SLIDE SHOWbutton.
Images are played back one after another.
2. Press the SLIDE SHOW button to stop the slide show.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
MV650i
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
AE SHIFT
MIX/SLIDESHOW
AE SHIFT
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 111
112
Usi
ng
a M
emo
ry C
ard
MV
630i
MV
650i
Card Jump FunctionYou can locate still images/movies without displaying them one by one. The number in
the upper right of the screen indicates the image number of the current image by the
total number of images.
In single image display, press and hold the CARD + orCARD – button.
• Press the CARD + button to jump forward and the CARD – button
to jump backward.
• When you release the button, the still image/movie of the
displayed image number appears.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
E
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 112
113
Usin
g a M
emo
ry Card
MV
630iM
V650i
E
Protecting ImagesYou can protect important images from accidental erasure during single image display
or index screen display.
If a memory card is formatted, all images, even protected ones, will be erasedpermanently.
❍ The sample images recorded on the supplied SD Memory Card are alreadyprotected.
❍ Movies can only be protected when the first or last scene is displayedas a still image. They cannot be protected during playback pause.
❍ Make sure to insert a memory card that contains images.
Protecting during Single Image Display
1. Select the image you wish to protect.
2. Press the selector dial to open the FILE OPERATION menu.
3. Select [PROTECT ].
• “ ” appears and now the image cannot be erased.
• To cancel the protection, press the selector dial.
4. Select [b RETURN] to close the menu.
Protecting during Index Screen Display
1. In single image display, press the (index screen) button.
Up to 6 images appear.
2. Open the menu and select [CARD OPERATIONS].
3. Select [\ PROTECT ].
4. Select the image you wish to protect and press the selector dial.
• “ ” appears on the image.
• Repeat this step to protect more images.
• To cancel the protection, press the selector dial.
5. Press the MENU button.
To cancel the protection, press the selector dial in step 4. “ ” disappears andthe image can now be erased.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
MV650i
PROTECTCARD OPERATIONS( 43)
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 113
114
Usi
ng
a M
emo
ry C
ard
MV
630i
MV
650i
E
Erasing ImagesYou can erase images singly or all at once.
Be careful when erasing images. Erased images cannot be recovered.
❍ Protected images cannot be erased. ❍ Movies can only be erased when the first or last scene is displayed as
a still image. They cannot be erased in playback pause mode.❍ Make sure to insert a memory card that contains images.
Erasing a Single Image
1. Select the image you wish to erase.
2. Press the selector dial to open the FILE OPERATION menu.
3. Select [IMAGE ERASE].• “ERASE THIS IMAGE?”, [NO] and [YES] appears.• If an image is protected, [YES] appears in purple.
4. Select [YES].The image is erased and the previous image appears.
5. Select [b RETURN] to close the menu.
Erasing a Single Image/All Images
1. Open the menu and select [CARD OPERATIONS].
2. Select [IMAGE ERASE].
3. Select [SINGLE] or [ALL].• When erasing a single image: “ERASE THIS IMAGE?” [NO] and [YES] appears. If an
image is protected, [YES] appears in purple.• When erasing all images: “ERASE ALL IMAGES? [EXCEPT FOR IMAGES]”, [NO]
and [YES] appears.
4. Select [YES] and close the menu.• When erasing a single image: The image is erased and the previous image appears. To
erase another image, select the image with the CARD +/– button and select [YES].• When erasing all images: All images with exception of the protected images are
erased.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
MV650i
IMAGE ERASECARD OPERATIONS( 43)
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 114
115
Usin
g a M
emo
ry Card
MV
630iM
V650i
E
Selecting Still Images for Printing (Print Order)You can select still images for printing and set the number of copies. These print order
settings are compatible with the Digital Print Order Format (DPOF) standards.
❍ Make sure to insert a memory card that contains images.❍ A maximum of 200 still images can be selected.❍ Movies cannot be printed.
Selecting in Single Image Display
1. Select the still image you wish to print.
2. Press the selector dial to open the FILE OPERATION menu.
3. Select [ PRINT ORDER].
4. Select the number of copies.
• “ ” appears on the image.
• To cancel the print order, set the number of copies to 0.
5. Select [b RETURN] to close the menu.
Selecting in Index Screen Display
1. In single image display, press the (index screen) button.
Up to 6 images appear.
2. Open the menu and select [CARD OPERATIONS].
3. Select [\ PRINT ORDER].
4. Select the still image you wish to print and press the selector dial.
5. Set the number of copies with the selector dial and close the menu.
• “ “ appears on the image.
• To cancel the print order, set the number of copies to 0.
• Repeat steps 4 and 5 to continue the print order setting.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
MV650i
PRINT ORDERCARD OPERATIONS( 43)
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 115
116
Usi
ng
a M
emo
ry C
ard
MV
630i
MV
650i
Erasing All Print Orders
1. In single image display, open the menu and select [CARD OPERATIONS].
2. Select [ PRINT ORDERS ALL ERASE].
“ERASE ALL PRINT ORDERS?”, [NO] and [YES] appears.
3. Select [YES].
All “ ” disappear.
4. Select [b RETURN] to close the menu.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
EPRINT ORDERS ALL ERASECARD OPERATIONS
( 43)
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 116
117
Usin
g a M
emo
ry Card
MV
630iM
V650i
E
Printing with the Direct Print FunctionYou can print still images by connecting the camcorder to a Canon Bubble Jet Printer
with Direct Print function. The Direct Print function can also be used with the print
order settings ( 115).
❍ Observe the following precautions during printing, otherwise printing may notbe performed correctly.- Do not turn off the camcorder or the printer.- Do not change the position of the TAPE/CARD switch.- Do not detach the cable.- Do not remove the memory card.
❍ Canon Bubble Jet Printers with Direct Print function (as of January 2003):S830D, S820D, S530D.
❍ We recommend powering the camcorder from a household power source.❍ Refer also to the instruction manual of the respective printer.
Connecting the Printer to the Camcorder
1. Turn off the camcorder and insert a memory card that contains images.
2. Connect a power source to the printer and turn on the printer.
3. Set the camcorder to CARD PLAY (VCR) mode.
Wait until the card access indicator stops flashing.
4. Connect the camcorder to the printer using the cable.
appears when the printer is properly connected to the camcorder. (Does not
appear with movies, or still images that cannot be played back with the camcorder.)
Print SET
TAPECARD
POWERPOWER
OFFOFF
(VCR)PLAY
CAMERACAMERA
Canon Bubble Jet Printer with directprint function
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 117
118
Usi
ng
a M
emo
ry C
ard
MV
630i
MV
650i
E
Printing
1. In single image display, select the still image youwish to print and press the selector dial.
The print setting menu appears.
2. Set the number of copies and the print style.
• Selecting the Number of Copies.
• Setting the Print Style.
3. Select [Print] and press the selector dial.
Printing starts. The print setting menu disappears when printing
is complete.
If an error message appears, see Printing Errors ( 120) and Direct Print RelatedMessages ( 139).
Selecting the Number of CopiesA maximum of 9 copies can be selected for one still image.
1. In the print setting menu, turn the selector dial sothat appears next to [Copies] and press theselector dial.
2. Turn the selector dial to select the number of copies and press theselector dial.
Setting the Print Style
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
Paper Size Card #1*, Card #2*, Card #3*,LTR, A4
For details on paper type, refer to the Bubble Jet Printer UserGuide.
Borders Borderless Prints right to the edges of the page
Bordered Prints with a border
* Recommended paper size
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 118
119
Usin
g a M
emo
ry Card
MV
630iM
V650i
E
Selecting the paper size:1. In the print setting menu, turn the selector dial to
select [Style] and press the selector dial.
2. Make sure that is selected and press the selectordial.
3. Turn the selector dial to select the paper size and press the selector dial.
4. Press the MENU button.
You return to the print setting menu.
Selecting the Borders:1. In the print setting menu, turn the selector dial to
select [Style] and press the selector dial.
2. Select and press the selector dial.
3. Select a setting option and press the selector dial.
4. Press the MENU button.
You return to the print setting menu.
❍ Bordered: The image area remains relatively unchanged from the recordedimage when it is printed.
❍ Borderless: The centre portion of the recorded image is printed at an enlargedsize. The image’s top, bottom and sides may be cropped slightly.
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 119
120
Usi
ng
a M
emo
ry C
ard
MV
630i
MV
650i
E
Printing with Print Order SettingsYou can print still images you have selected with the Print Order function. If you wish
to print more than 1 copy, set the number of copies in the print order ( 115).
1. Connect the printer to the camcorder ( 117).
2. Press the MENU button.
3. Select [\ PRINT].
• The print setting menu appears.
• “Set print order” appears, when you connect a printer with direct print function and
select [\ PRINT] without having set the print order.
• The total number of prints set in the print order is displayed on the upper left of the
screen.
4. Set the print style.
Setting the Print Style ( 118).
5. In the print setting menu, select [OK] and press the selector dial.
Printing starts. The print setting menu disappears when printing is complete.
❍ Cancel PrintingPress the selector dial while “Now Printing” is displayed. A confirmation dialogappears. Select [OK] and press the selector dial. Printing stops even if it isincomplete and the paper is fed through.
❍ Restarting Printing (with printer order only)Open the CARD PLAY (VCR) menu and select [\ PRINT]. Select [Restart] inthe print setting menu and press the selector dial. The remaining images willbe printed.Printing cannot be restarted in the following cases:- When you change the print order settings.- When you delete a still image with print order settings.
❍ Printing ErrorsIf an error occurs during the printing process, an error message appears ( 139). With most errors, printing resumes automatically after you correctthe error. If the error persists, press the selector dial to cancel printing.
❍ Follow below procedure when disconnecting the interface cable:1. Disconnect the cable from the camcorder and printer.2. Turn off the camcorder.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
PRINT( 43)
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 120
121
Usin
g a M
emo
ry Card
MV
630iM
V650i
E
Combining Images (Card Mix)You can produce effects not possible with just a tape with the Card Mix function.
Choose one of the sample images provided on the supplied SD Memory Card (such as
picture frames, backgrounds and animations) and combine it with the live video
recording.
❍ Card Mix cannot be used in the Night and Super Night (MV650i) mode.❍ Movies recorded on a memory card cannot be combined with
camcorder recordings.
❍ Make sure to load a cassette and to insert a memory card that contains cardmix images.
❍ Additional sample images are provided on the supplied DIGITAL VIDEOSOLUTION DISK. For instructions on how to upload them to the memory card,refer to Adding Still Images from Your Computer to the Memory Card in theDIGITAL VIDEO SOLUTION DISK Software Instruction Manual.
❍ Reselect the card mix image when you have turned off the camcorder orchanged the position of the program selector.
Card Mix EffectsYou can select from the following 4 types of Card Mix effects:
Card Chroma Key (CARD CHROMA)Combines frames with your recordings. The live video recording will appear in place of
the blue area of the card mix image. If you create your own frame, make sure that the
area the live recording should appear is blue.
Mix level adjustment: blue area of the still image.
MV650i
Live video recording Card mix image
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 121
122
Usi
ng
a M
emo
ry C
ard
MV
630i
MV
650i
E
Card Luminance Key (CARD LUMI.)Combines illustrations or title with your recordings. The live video recording will
appear in place of the light area of the card mix image. You can create your own title
or illustration by drawing on a white paper and recording it to the memory card.
Mix level adjustment: light area of the still image.
Camera Chroma Key (CAM. CHROMA)Combines backgrounds with your recordings. Record your subject in front of a blue
curtain, and the subject not blue will be superimposed on the card mix image.
Mix level adjustment: blue area of the live video recording.
Card Animation (C. ANIMATION)Combines animations with your recordings. You can choose from 3 types of card
animation effects.
Corner: Animation appears on the upper left and the lower right corner of the screen.
Straight: Animation appears on the top and bottom of the screen and moves to the
right and left.
Random: Animation moves randomly in the display.
Mix level adjustment: blue area of the card animation image.
Live video recording Card mix image
Live video recording Card mix image
Live video recording Card mix image
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 122
123
Usin
g a M
emo
ry Card
MV
630iM
V650i
E
Selecting the Card Mix Effect
1. Set the program selector to Q.
2. Open the menu and select [\ CARD MIX].
The card mix menu appears.
3. Select the image you wish to combine with theCARD +/– button.
4. Select [MIX TYPE].
[CARD CHROMA], [CARD LUMI.], [CAM. CHROMA] and [C. ANIMATION] appears.
5. Select the mix type matching the image you have selected ( 131).
• The screen shows the combined image.
• When you have selected [C. ANIMATION], select [ANIMAT. TYPE] and select between
[CORNER], [STRAIGHT] and [RANDOM].
6. To adjust the mix level, select [MIX LEVEL] and adjust it with theselector dial.
7. Close the menu.
“CARD MIX” flashes.
Activating the Card Mix Effect
1. Press the CARD MIX button.
• “CARD MIX” stops flashing.
• The combined image appears.
• You can activate and deactivate the card mix effect by pressing
the CARD MIX button.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
MENU
MIX/SLIDESHOW
MIX LEVEL•• CARD MIX – +MIX TYPE•••CARD CHROMA( 43)
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 123
124
Usi
ng
a M
emo
ry C
ard
MV
630i
MV
650i
E
Recording with the Card Mix Effect
Movie:
1. Press the start/stop button to begin recording.
The combined image is recorded on the tape.
2. Press the start/stop button to end recording.
Still Image:
1. Press the PHOTO button halfway.
F flashes in white and turns green when focus is adjusted.
2. Press the PHOTO button fully.
• The camcorder records the still image on the tape for approx. 6
seconds. During this time, the camcorder displays the still
image and keeps recording the sound.
• The camcorder returns to record pause mode.
PHOTO
PHOTOOFFOFF
(VCR)(VCR)PLAY
CAMERA
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 124
125
Usin
g a M
emo
ry Card
MV
630iM
V650i
E
Copying Still ImagesYou can copy still images from tape to memory card, or from memory card to tape.
❍ All still images from the selected still image onward will be copied.❍ The image size of a still image copied from tape to memory card will be 640 ×
480.❍ The data code of the still image reflects the date and time it has been copied.
Copying Still Images from Tape to Memory CardInsert a memory card with enough remaining capacity, and load a recorded cassette.
1. Locate the still image you wish to copy on the tapeand stop the tape shortly before the still image.
• You can also use the photo search function to easily locate the
still image.
• To copy all still images from the tape, rewind the tape to the
beginning.
2. Open the menu and select [CARD OPERATIONS].
3. Select [COPY [b \ ] ].
[CANCEL] and [EXECUTE] appears.
4. Select [EXECUTE].
• “NOW COPYING” appears.
• The still image being copied is shown on the screen.
• Copying stops when the tape reaches the end or the memory card is full (“CARD
FULL” appears).
5. Press the 3 (stop) button to end copying.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
COPYCARD OPERATIONS [ ]
AE SHIFT
( 43)
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 125
126
Usi
ng
a M
emo
ry C
ard
MV
630i
MV
650i
E
Copying Still Images from Memory Card to TapeLoad a cassette with enough free space, and insert a recorded memory card. Make
sure that the protect tab on the cassette is set to allow recording.
1. Select the first still image you wish to copy with theCARD +/– buttons.
To copy all still images from the memory card, select the first still
image.
2. Open the menu and select [CARD OPERATIONS].
3. Select [COPY [ \ b] ].
[CANCEL] and [EXECUTE] appears.
4. Select [EXECUTE].
• “NOW COPYING” appears.
• It takes about 6 seconds per still image to be copied to the tape.
• Copying stops when all still images are copied or the tape is full.
5. Press the 3 (stop) button to end copying.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
COPYCARD OPERATIONS [ ]
AE SHIFT
( 43)
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 126
127
Usin
g a M
emo
ry Card
MV
630iM
V650i
E
Formatting a Memory CardFormat new memory cards, or when you get the message “CARD ERROR”. You can
also format a memory card to erase all images recorded on it.
The camcorder formats memory cards in the Design rule for Camera File system (DCF)
standard.
❍ Formatting a memory card erases all data, including protected images.❍ Images erased by formatting cannot be recovered.❍ If you use a memory card other than the supplied one, format it with the
camcorder.❍ Makes sure to insert the memory card you wish to format into the camcorder.
1. Open the menu and select [CARD OPERATIONS].
2. Select [FORMAT].
[CANCEL] and [EXECUTE] appears.
3. Select [EXECUTE].
[FORMAT THIS CARD?], [NO] and [YES] appears.
4. Select [YES] and close the menu.
• Formatting starts.
• Selecting [NO] brings you back to step 3.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
FORMATCARD OPERATIONS( 43)
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 127
128
Usi
ng
a M
emo
ry C
ard
MV
630i
MV
650i
E
Connecting to a Computer Using a USB CableYou can download images from the memory card to a computer using the supplied
USB cable. With the supplied software, you can easily download, browse and archive
images, and arrange still images for printout.
For instructions on how to connect the camcorder to the computer, andinstall and operate the software, refer to the DIGITAL VIDEO SOLUTIONDISK Software Instruction Manual.
• Refer also to the computer instruction manual.
• “PC CONNECT ” appears to indicate that the camcorder is
connected to the computer via USB cable.
❍ Do not disconnect the USB cable, remove the memory card, change theposition of the POWER switch or turn off the camcorder and computer whiledata is being transferred to the computer (while the camcorder’s card accessindicator is flashing). Doing so may damage the memory card’s data.
❍ Operation may not work correctly depending on the software and thespecifications/settings of your computer.
❍ The image file on your memory card and the image files saved on the hard diskdrive of your computer are valuable, original data files. If you wish to useimage files on your computer, make copies of them first, and use the copiedfile, retaining the original.
❍ We recommend powering the camcorder from a household power sourcewhile it is connected to the computer.
❍ The light-up buttons turn off during USB connection.❍ For transferring recordings from to a computer using a DV cable, see p. 98.❍ Still images/movies recorded on a tape cannot be transferred to a computer via
USB interface.
MV650i
PC CONNECT
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 128
129
Usin
g a M
emo
ry Card
MV
630iM
V650i
E
Creating a Start-up ImageYou can create a start-up image using a still image on the memory card or a sample
start-up image provided on the DIGITAL VIDEO SOLUTION DISK and save it as [MY
IMAGE].
❍ Make sure to insert a memory card with enough remaining capacity.❍ Before you create a start-up image, you need to record a still image on the
memory card.❍ Retain the original data of the still image you have set as the start-up image on
your computer or removable disk.
Preparations
Record a still image on the memory card.
OR
Upload a still image from your computer to the memory card using thesoftware in the DIGITAL VIDEO SOLUTION DISK.
For instruction on how to upload a still image to the memory card, refer to Adding Still
Images from Your Computer to the Memory Card in the DIGITAL VIDEO SOLUTION DISK
Software Instruction Manual.
Setting the Still Image as Start-up Image
1. Open the menu.
2. Select [MY CAMERA].
3. Select [CREATE START-UP IMAGE].
[SET THIS AS START-UP IMAGE?], [YES] and [NO] appears.
4. Select a still image with the CARD +/– buttons and select [YES].
[OVERWRITE MY IMAGE?], [YES] and [NO] appears.
5. Select [YES].
The still image will be saved, and the image that was saved to [MY IMAGE] is erased.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
CREATE START–UP IMAGEMY CAMERA( 43)
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 129
130
Usi
ng
a M
emo
ry C
ard
MV
630i
MV
650i
E
Memory Card InformationImages recorded on a memory card with this camcorder can be transferred to a
computer using the following products for SD Memory Cards or MultiMediaCards:
PC Card Adapter: An adapter to insert a memory card into the card slot on the
computer.
USB Reader/Writer: Connects to the USB port of a computer for direct access to the
memory card.
FD Adapter: An adapter to insert a memory card into the floppy disk drive on
the computer.
Memory Cards that are confirmed to operate with this camcorder (as of January 2003):SD Memory Card: Panasonic: 16 MB, 32 MB, 64 MB, 128 MB, 256 MB, 512 MB
SanDisk: 16 MB, 32 MB, 64 MB
MultiMediaCard: SanDisk: 16 MB, 32 MB, 64 MB
However, we cannot guarantee that all of these memory cards work properly.
Memory Card Handling Precautions❍ Format new memory cards with the camcorder. Memory cards formatted with
other devices such as a computer may not operate correctly. ❍ We recommend saving backups of memory card images on your computer’s hard
drive or other external memory device. Image data may be corrupted or lost due tomemory card defects or exposure to static electricity. Canon Inc. makes nowarranties for corrupted or lost data.
❍ Do not turn off the camcorder, disconnect the power source or remove the memorycard while the card access indicator is flashing.
❍ Do not use memory cards in places subject to strong magnetic fields.❍ Do not leave memory cards in places subject to high humidity and high
temperature.❍ Do not disassemble memory cards.❍ Do not bend, drop, or subject memory cards to shocks and do not expose them to
water.❍ Moving a memory card rapidly between hot and cold temperatures may cause
condensation to form on its external and internal surfaces. If condensation formson the card, put it aside until the droplets have evaporated completely.
❍ Do not touch or expose the terminals to dust or dirt.❍ Store and carry memory cards in the supplied case to protect the terminals.❍ Check the direction before inserting the memory card. Forcing a memory card
backwards into the slot may damage the memory card or the camcorder.❍ Do not remove the label from the memory card, or affix other labels on the
memory card. If you wish to add labels, affix them to the case.
5_D73PAL_E(99-132) 02.12.26 9:30 PM Page 130
131
Usin
g a M
emo
ry Card
MV
630iM
V650i
E
Sample Images27 sample images are pre-recorded on the supplied SD Memory Card: 8 card chroma
key images, 5 card luminance key images, 2 camera chroma key images and 12 card
animation images.
Card Chroma Key
Card Luminance Key
Camera Chroma Key
Card Animation
5_D73PAL_E(99-132) 02.12.26 9:31 PM Page 131
132
Usi
ng
a M
emo
ry C
ard
MV
630i
MV
650i
E
The sample images recorded on the supplied SD Memory Card are intended onlyfor the personal use with this camcorder. Do not use these sample images forother purposes.
If you have mistakenly erased the Card Mix sample images on the supplied SDMemory Card, they can be downloaded from the following homepages:http://www.canon-europa.com/products/products.htmlhttp://www.canon-asia.com/http://www.canon.com.auFor details on how to add the downloaded images to the memory card, refer toAdding Still Images from Your Computer to the Memory Card in the DIGITALVIDEO SOLUTION DISK Software Instruction Manual.If you cannot use the USB cable to connect the camcorder to a computer, you willneed a PC Card Adapter to upload the images to a memory card.
PhotoEssentials – Royalty Free Stock Photography
The PhotoEssentials suite of royalty-free images on CD-ROM features premium quality assignment
photography and is ideally suited for use in advertising, brochures, reports, multimedia, websites,
books, packaging and more.
For more information, please visit their website www.photoessentials.com
5_D73PAL_E(99-132) 02.12.26 9:31 PM Page 132
133
Ad
ditio
nal
Info
rmatio
n
E
Screen Displays
LCD Screen DisplaysYou can hide the displays on the LCD screen to have a clear screen for playback.
Open the menu and select [DISPLAY SET UP]. Select [DISPLAYS], set it to[OFF <PLAYBK>] and close the menu.
• The LCD screen will become completely blank (also the TV screen if connected).
• Warning messages still appear, and the data code appears if turned on.
• Tape operation displays appear for 2 seconds.
• Displays cannot be hidden on the index screen.
TV Screen DisplaysWhen you connect a TV for recording/playback, you can hide the displays on the TV
screen. For connecting instructions, see Playing Back on a TV Screen ( 39).
Press the TV SCREEN button on the wireless controller.
• When the POWER switch is set to CAMERA: The displays
disappear from the TV screen and appear when you press the
button again.
• When the POWER switch is set to PLAY (VCR): The displays appear on the connected TV
screen and disappear when you press the button again. The setting resets to the OFF
setting when you turn the camcorder off.
When the TV screen displays are hidden, the displays still appear on the LCD screen. If
you turn on the data code, displays other than the data code will disappear from the LCD
screen.
You can also change the setting in the menu during recording:
Open the menu and select [DISPLAY SET UP]. Select [TV SCREEN], set it to[OFF] and close the menu.
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
MV630iMV650i
CARD PLAY (VCR)CARD CAMERAPLAY (VCR)CAMERA
TV SCREEN•••ONDISPLAY SET UP
DISPLAYS••••ONDISPLAY SET UP
SELF T. D.EFFECT.
ON/OFF SET
MENU
TV SCREEN
SEARCH SELECTDATA CODE
INDEX SLIDE SHOW CARD
( 43)
( 43)
6_D73PAL_E(133-154) 02.12.26 9:32 PM Page 133
134
Ad
dit
ion
alIn
form
atio
nScreen Displays during Basic Recording/Playback
indicates flashing.
CAMERA mode (battery pack attached):
• Remote sensor mode and audio mode disappear after 4
seconds.
PLAY (VCR) mode:
• Remote sensor mode and volume bar disappear after 4
seconds.
E
: Backup battery ( 17)
: Condensation warning ( 142)
Time code ( 85)Remaining tapeRemaining battery charge ( 16)
Remote sensor mode ( 48)
Audio mode ( 70)
: Fast forward playback/rewind playback ( 36)
: ×2 playback (forward and reverse) ( 36)
: ×1 playback (forward and reverse) ( 36)
: Slow playback (forward and reverse) ( 36)
: Frame advance playback/frame reverse playback ( 36)
: Playback pause (forward and reverse) ( 36)
: Date search/photo search ( 84)
: Zero set memory (forward and reverse) ( 85)
: AV insert editing ( 93)*: Audio dubbing ( 95)
* Not available with the MV600.
END
STEREO11:23:45:00
1
16bit
PAUSE
/
/
2 2/
1 1/
/
/
/
/
//
RECPAUSESTOPEJECT
FF REW
RTN RTN
PS PAUSE0:00:00
12bit
1
5min
PS STOPSTEREO10:00:00:00
5min
1
+–
6_D73PAL_E(133-154) 02.12.26 9:32 PM Page 134
135
Ad
ditio
nal
Info
rmatio
n
E
Screen Displays during Advanced Recording/Playback
CAMERA Mode
* ** and MV630iMV650iMV650i
1/100
CARD MIXFADE–T
12bit16:9
1sec
PHOTO
WSON
12:00 PM1.JAN.2003
TW PS
AEMF
0
+–
Zoom ( 28)Recording mode ( 53)
Self-timer ( 69)Headphones ( 37)
Wind screen ( 70)
16:9 mode ( 51)Photo mode ( 54)
Accessory attached tothe Advanced Accessory shoe* ( 73)
Audio mode ( 70)
Recording reminder/Self-timer countdown ( 69)Photo recording timer ( 54)
Image stabilizer ( 68)
AE shift ( 76)Program AE ( 56)Manual focus ( 74)Shutter speed ( 77)White balance ( 79)Card mix** ( 121)Digital effects ( 60)Date and time ( 82)
AF/AE locked in Photo mode ( 54)
PLAY (VCR) Mode
* Not available with the MV600.
PHOTO SEARCH
1/1000
DV IN
F1.8
MIX/VARI. 1
1 101 10
12bit12:00 PM1.JAN.2003
+–
12bit audio out ( 97)
Photo search/Date search ( 84)
Volume level of built-in speaker or headphones ( 38)
Audio mode* ( 70)
DV input* ( 89)
Photo search/Date search ( 84)/AV insert* ( 93)/Audio dubbing ( 95)
Data code ( 82)
6_D73PAL_E(133-154) 02.12.26 9:32 PM Page 135
136
Ad
dit
ion
alIn
form
atio
n
E
CARD CAMERA Mode
* MV650i
MV630iMV650i
501024320
1/120
1 2
CLOSE12:00 PM1.JAN.2003
TW
0AEMF
S.FINE
Accessory attached tothe Advanced Accessory shoe* ( 72)
Recording on a memory card ( 103)Still image quality ( 100)
Movie size* ( 101)
Still image size ( 100)
Self-timer ( 69)
Stitch assist ( 106)
Remaining card capacity ( 100)
Stitch assist ( 106)
Zoom ( 28)
Program AE ( 56)
AE shift ( 76)Manual focus ( 74)Shutter speed ( 77)White balance ( 79)Date and time ( 82)AF/AE locked in Photo mode ( 103)
CARD PLAY (VCR) ModeMV630iMV650i
SLIDE SHOW 101–014343/50
640 480
12:00 PM1.JAN.2003
Print order ( 115) Protect mark ( 113)
Folder number-File number ( 101)
Current still image/Total still images
Slide show ( 111)
Accessing a memory card ( 110)
Data code ( 82)
6_D73PAL_E(133-154) 02.12.26 9:32 PM Page 136
137
Ad
ditio
nal
Info
rmatio
n
E
List of Messages
Message ExplanationYou have not set the time zone, date and time. This message appears each time you turn the power on until you set the time zone, date and time.Battery pack is exhausted. Replace or charge the battery pack.Cassette is protected. Replace the cassette or change the position of the protect switch.Camcorder stopped operating to protect the tape. Unload and reload the cassette.DV cable is not connected, or the connected digital device is turned off.Condensation has been detected in the camcorder. Tape reached the end. Rewind the tape or replace the cassette. You attempted to perform audio dubbing or AV insert on a tape recorded in a mode other than the SP mode. You attempted to perform audio dubbing on a tape recorded in 16-bit or 12-bit 4-channel sound. You attempted to perform audio dubbing or AV insert on a tape with a blank section. You attempted to play back a copyright protected tape. You attempted to dub a copyright protected tape. May also appear when an anomalous signal is received during analog line-in recording, or during analog-digital conversion of a copyright protected tape.
SET THE TIME ZONE, DATE AND TIME
CHANGE THE BATTERY PACKTHE TAPE IS SET FOR ERASURE PREVENTIONREMOVE THE CASSETTECHECK THE DV INPUT
CONDENSATION HAS BEEN DETECTEDTAPE END
CHECK THE CASSETTE [REC MODE]CHECK THE CASSETTE [AUDIO MODE]CHECK THE CASSETTE [BLANK]COPYRIGHT PROTECTED PLAYBACK IS RESTRICTEDCOPYRIGHT PROTECTED DUBBING RESTRICTED
23
14
21
20
89
142
20
53
95
93
90
90
6_D73PAL_E(133-154) 02.12.26 9:32 PM Page 137
138
Ad
dit
ion
alIn
form
atio
n
E
Message ExplanationMemory card not is inserted into the camcorder.SD Memory Card is set for erasure prevention. Replace the card or change the position of the protect switch.No images are recorded on the memory card.A memory card error occurred. The camcorder cannot record or play back the image.The error may be temporary. If the message disappears after 4 seconds and flashes red, turn the camcorder off, remove the card and reinsert the card. If changes to green, you can continue recording/playback.No remaining capacity on the memory card. Replace with another card or erase images.File or folder number has reached the maximum value.Image is recorded in a not compatible JPEG format or another format not compatible with the camcorder, or the image file is corrupted.You attempted to set more than 200 still images in the print order.Some analog images cannot be recorded on the memory card depending on the signal.
NO CARDTHE TAPE IS SET FOR ERASURE PREVENTIONNO IMAGESCARD ERROR
CARD FULL
NAMING ERRORUNIDENTIFIABLE IMAGE
PRINT ORDER ERROR
THIS IMAGE CANNOT BE RECORDED
9999
11099
114
101110
115
105
Memory Card Related MessagesMV630iMV650i
6_D73PAL_E(133-154) 02.12.26 9:32 PM Page 138
139
Ad
ditio
nal
Info
rmatio
n
E
Direct Print Related MessagesMV630iMV650i
Message ExplanationPaper cassette is not correctly inserted or is out of paper.The paper jammed during printing.The ink cartridge is not inserted or is out of ink.The printer is experiencing a data transmission error.You attempted to use the print order settings to print X images that were made with another camcorder, have a different format or were edited on a computer.You attempted to print an image that was made with another camcorder, has a different format, or was edited on a computer.You attempted to print an image from the CARD PLAY (VCR) menu [\ PRINT] without having set the print order.The printer is printing from a computer or a memory card inserted into the printer. It automatically starts printing from the camcorder when current prints are complete.Printer is warming up. The printer automatically starts printing when it is ready.No print head is installed in the printer.Printer cover is open. Close the printer cover securely.Wrong paper. Cancel printing and set the paper you chose in the print settings menu.Paper lever error occurred. Adjust the paper selection lever to the proper position.The ink tank needs to be replaced soon. Prepare a new ink tank. If you select [Continue] in the error screen, you can restart printing.Waste tank is full. You can restart printing by pressing the RESUME/CANCEL button on the Bubble Jet Printer. Request replacement of the waste tank at the shop where you purchased the printer or the nearest Canon customer support centre listed in the Bubble Jet Quick Start Guide.Turn off the printer and turn it back on. If the error persists, consult the nearest Canon customer support centre listed in the Bubble Jet Quick Start Guide.
No PaperPaper JamNo InkCommunication ErrorCould not print X images
Cannot Print!
Set print order
Printer in use
Printer warming up
No printheadPrinter cover openMedia type error
Paper lever error
Low ink level
Waste tank full
Printer error
6_D73PAL_E(133-154) 02.12.26 9:32 PM Page 139
140
Ad
dit
ion
alIn
form
atio
n
E
Maintenance
Camcorder Handling Precautions❍ Do not carry the camcorder by the LCD panel or viewfinder.
❍ Do not leave the camcorder in places subject to high temperatures, such as a sun-
heated car, and high humidity.
❍ Do not use the camcorder in places subject to magnetic or electric fields such as
near the TV transmitters or portable communication devices.
❍ Do not point the lens or viewfinder at strong light sources. Do not leave the
camcorder pointed at a bright subject.
❍ Do not use the camcorder in dusty or sandy places. Dust or sand getting inside the
cassette or camcorder may cause damage. Dust and sand can also damage the lens.
Attach the lens cap after use.
❍ The camcorder is not waterproof. Water, mud or salt getting inside the cassette or
camcorder may cause damage.
❍ Be careful of heat generated by lighting equipment.
❍ Do not disassemble the camcorder. If the camcorder does not function properly,
consult qualified service personnel.
❍ Handle the camcorder with care. Do not subject the camcorder to shocks or
vibration as this may cause damage.
❍ Avoid sudden changes in temperature. Moving the camcorder rapidly between hot
and cold temperatures may cause condensation to form on its internal surfaces
( 142).
Storage❍ If you do not intend to use the camcorder for a long time, store it in a place free of
dust, in low humidity, and at temperatures not higher than 86˚F (30˚C).
❍ After storage, check the functions of your camcorder to make sure that the
camcorder is still working properly.
CleaningCamcorder Body and Lens❍ Use a soft, dry cloth to clean the camcorder body and lens. Never use chemically
treated cloth or volatile solvents such as paint thinner.
LCD Screen❍ Clean the LCD screen using a commercially available cleaning cloth for glasses.
❍ Condensation may form on the surface of the screen when the temperature
changes suddenly. Wipe it with a soft dry cloth.
6_D73PAL_E(133-154) 02.12.26 9:32 PM Page 140
141
Ad
ditio
nal
Info
rmatio
n❍ At cold temperatures, the screen may be darker than usual. This is not a
malfunction. The screen returns to normal when the camcorder warms up.
Viewfinder❍ Rotate the viewfinder upward. Remove the protect cover
and clean the glass with a cotton swab. Reattach the
protect cover when finished.
❍ Be careful not to scratch the glass when cleaning.
Video Heads❍ When the playback picture becomes distorted, the video heads need to be cleaned.
❍ To maintain the best picture quality, we recommend cleaning the video heads
frequently with the Canon DVM-CL Digital Video Head Cleaning Cassette or a
commercially available dry cleaning cassette.
❍ Do not use wet type cleaning cassettes as this may damage the camcorder.
E
6_D73PAL_E(133-154) 02.12.26 9:32 PM Page 141
142
Ad
dit
ion
alIn
form
atio
n
E
CondensationMoving the camcorder rapidly between hot and cold temperature may cause
condensation (water droplets) to form on its internal surfaces. Stop using the
camcorder if condensation is detected. Continued use may damage the camcorder.
Condensation may form in the following cases:
How to avoid condensation:❍ Unload the cassette, place the camcorder in an airtight plastic bag and let it adjust
to temperature changes slowly before removing it from the bag.
When condensation is detected:❍ The camcorder stops operating and the warning message “CONDENSATION HAS
BEEN DETECTED” appears for approx. 4 seconds and h starts flashing.
❍ If a cassette is loaded, the warning message “REMOVE THE CASSETTE” appears and
v starts flashing. Remove the cassette immediately and leave the cassette
compartment open. Leaving the cassette in the camcorder may damage the tape.
❍ A cassette cannot be loaded when condensation is detected.
Resuming use:❍ It takes about 1 hour until the water droplets evaporate. After the condensation
warning stops flashing, wait for 1 more hour before resuming use.
When the camcorder is moved from an
air-conditioned room to a warm, humid
place
When the camcorder is moved from a
cold place to a warm room
When the camcorder is left in a humid
room
When a cold room is heated rapidly
6_D73PAL_E(133-154) 02.12.26 9:32 PM Page 142
143
Ad
ditio
nal
Info
rmatio
n
E
Using the Camcorder AbroadPower SourcesYou can use the compact power adapter to operate the camcorder and to charge
battery packs in any country with power supply between 100 and 240 V AC, 50/60 Hz.
Consult the Canon Service Centre for information on plug adapters for overseas use.
Playback on a TV ScreenYou can only play back your recordings on TVs with PAL system. The PAL system is
used in the following countries/areas:
Algeria, Australia, Austria, Bangladesh, Belgium, Brunei, China, Denmark, Finland,
Germany, Hong Kong Special Administrative Region, Iceland, India, Indonesia, Ireland,
Italy, Jordan, Kenya, Kuwait, Liberia, Malaysia, Malta, Mozambique, the Netherlands,
New Zealand, North Korea, Norway, Oman, Pakistan, Portugal, Qatar, Sierra Leone,
Singapore, South Africa, Spain, Sri Lanka, Swaziland, Sweden, Switzerland, Tanzania,
Thailand, Turkey, Uganda, United Arab Emirates, United Kingdom, Yemen, former
Yugoslavia, Zambia.
6_D73PAL_E(133-154) 02.12.26 9:32 PM Page 143
144
Ad
dit
ion
alIn
form
atio
n
E
TroubleshootingIf you have a problem with your camcorder, refer to this checklist. Consult your dealer
or a Canon Service Centre if the problem persists.
Power Source
Recording/Playback
Problem Cause SolutionBattery pack is exhausted.
Battery pack is not correctly attached.Battery pack is exhausted.
Power save function has been activated.Battery pack is exhausted.
Cassette compartment cover is not fully open.Battery pack is exhausted.
The camcorder malfunctions.Battery pack is exhausted.
Replace or charge the battery pack.Attach the battery pack correctly.Replace or charge the battery pack.Turn on the camcorder.
Replace or charge the battery pack.Open the cassette compartment cover fully.Replace or charge the battery pack.Consult a Canon Service Centre.Replace or charge the battery pack.
Camcorder will not turn on.
The camcorder switches off by itself.
Cassette compartment will not open.
Cassette compartment stopped during loading/ unloading.
LCD/viewfinder switches on and off.
14
14
14
26
14
20
14
–
14
Camcorder is not turned on.Cassette is not loaded.Battery pack is exhausted.
Condensation is detected.Camcorder stopped operating to protect the tape.Camcorder and wireless controller are not set to the same remote sensor mode.Batteries of the wireless controller are exhausted.
Turn on the camcorder.Load a cassette.Replace or charge the battery pack.See reference page.Unload and reload the cassette.
Change the remote sensor modes.
Replace the batteries.
Buttons will not work.
k flashes on the screen.h flashes on the screen.“Remove the cassette” appears on the screen.
The wireless controller will not work.
262014
14220
48
22
6_D73PAL_E(133-154) 02.12.26 9:32 PM Page 144
145
Ad
ditio
nal
Info
rmatio
nRecording
Playback
E
Problem Cause SolutionCamcorder is not set to CAMERA mode.Time zone, date and time are not set, or the backup battery is exhausted.
Camcorder is turned off.Cassette is not loaded.Tape reached the end ( flashes on the screen).Cassette is protected (v flashes on the screen).
Camcorder is set to a mode other than the CAMERA mode.Autofocus does not work on that subject.Viewfinder is not adjusted.
Lens is dirty.Bright light in a dark scene may cause a vertical light bar (smear) to appear. This is not a malfunction.When recording near loud sound (such as fireworks, drums or concerts), sound may become distorted or may not be recorded in the actual sound level. This is not a malfunction.Viewfinder is not adjusted.
Set the camcorder to CAMERA mode.Set the time zone, date and time, or replace the backup battery and reset the date and time.Turn on the power.Load a cassette.Rewind the tape or replace the cassette.Replace the tape or change the position of the protect switch.Set the camcorder to CAMERA mode.Focus manually.
Adjust the viewfinder with the diopter adjustment lever.Clean the lens.
– – –
– – –
Adjust the viewfinder with the diopter adjustment lever.
Image will not appear on the screen.“Set the time zone, date and time” appears on the screen.
Pressing the start/stop button will not start recording.
Camcorder will not focus.
A vertical light bar appears on the screen.
Sound is distorted or recorded in a lower volume than the actual volume.
Viewfinder picture is blurred.
26
23
262020
21
26
74
18
140–
–
18
Camcorder is turned off, or is not set to PLAY (VCR) mode.Cassette is not loaded.Tape reached the end ( flashes on the screen).[AV/PHONES] is set to [PHONESH] in the menu.[AV / DV OUT] is set to [ON].TV/VIDEO selector on the TV is not set to VIDEO.Video heads are dirty.You attempted to play back or dub copyright protected tape.Speaker volume is turned off.
Set the camcorder to PLAY (VCR) mode.Load a cassette.Rewind the tape.
Set [AV/PHONES] to [AV] in the menu.Set [AV / DV OUT] to [OFF].
Set the selector to VIDEO.
Clean the video heads.Stop playback/dubbing.
Adjust the volume with the selector dial.
Pressing the playback button does not start playback.
Image will not appear on the TV screen.
Tape is running, but image will not appear on the TV screen.
No sound from the built-in speaker.
35
2035
37
92
41
14190
38
6_D73PAL_E(133-154) 02.12.26 9:32 PM Page 145
146
Ad
dit
ion
alIn
form
atio
n
E
Memory Card OperationMV630iMV650i
Problem Cause SolutionMemory card was not facing the correct direction.Memory card is full.
Memory card is not formatted.Memory card is not inserted.File number reached maximum value.
SD Memory Card is protected.Camcorder is not set to CARD PLAY (VCR) mode.Memory card is not inserted.Image is protected.SD memory card is protected.Card error occurred.
Turn the memory card over and reinsert it.Replace the memory card or erase images.Format the memory card.
Insert a memory card.Set [FILE NUMBERS] to [RESET] and insert a new memory card.Change the position of the protect switch.Set the camcorder to CARD PLAY (VCR) mode.Insert a memory card.Cancel the protection.Change the position of the protect switch.Turn off the camcorder. Remove and reinsert the memory card. Format the memory card if flashing persists.
Memory card cannot be inserted.Memory card cannot be recorded.
Memory card cannot be played back.
Image cannot be erased.
flashes red.
99
114
127
99101
99
110
9911399
127
6_D73PAL_E(133-154) 02.12.26 9:32 PM Page 146
147
Ad
ditio
nal
Info
rmatio
n
E
System Diagram (Availability differs from area to area)
MV650i MV630i
MultiMediaCard
IFC-300PCU USB Cable
PC Card Adapter
USB Reader/Writer
FD Adapter
BP-900 Series Battery Pack* VL-10Li
Battery Video Light
Stereo Microphone (commercially available)
WL-D80 Wireless Controller
WL-D79 Wireless Controller
MiniDV Video Cassette
CG-570 Battery Charger
CA-570 Compact Power Adapter
TV
VCR
SC-1000 Soft Carrying Case
S-150 S-video Cable
Digital Device
BP-500 Series Battery Pack
CB-570Car Battery Cable
Computer
CV-150F/CV-250FDV Cable
BP-500 Series Battery Pack
STV-250N Stereo Video Cable
PC-A10 SCART Adapter
WD-30.5 Wide-converter
WA-30.5 Wide Attachment
FS-30.5U Filter Set
TL-30.5 Tele-converter
SD Memory Card
VL-3 Video Light
DM-50 DirectionalStereo Microphone
SS-800 Shoulder Strap
WS-20 Wrist Strap
MV650i
MV650i MV630i
MV600i MV600
MV650i
MV650i
Bubble Jet Printer with direct print function
* Charging with the CA-920 Compact Power Adapter or CH-910 Dual BatteryCharger/Holder (both optional)
6_D73PAL_E(133-154) 02.12.26 9:32 PM Page 147
148
Ad
dit
ion
alIn
form
atio
n
E
Optional AccessoriesCall or visit your local retailer/dealer for genuine Canon video accessories.
BP-500 Series Battery PacksWhen you need extra battery packs, select from
the following: BP-511, BP-512, BP-522 or BP-535.
CG-570 Battery ChargerThe battery charger can be used with the
supplied CA-570 Compact Power Adapter or the
optional CB-570 Car Battery Cable to charge
BP-500 series battery packs.
CB-570 Car Battery CableUse the car battery cable with the CG-570
Battery Charger to charge battery packs on the
move. The car battery cable plugs into your car’s
cigarette lighter and runs off a 12-24 V DC
negative ground battery.
TL-30.5 Tele-converterThis tele-converter lens increases the focal
length of the camcorder lens by a factor of 1.9.
• The image stabilizer is not as effective when
the tele-converter is attached.
• The image quality may be degraded at the telephoto side.
• The minimum focusing distance with the Tele-converter is 4 m; 4 cm on maximum
wide angle.
Battery Pack Charging Time
BP-508 (MV630i/MV600i/MV600) 55 min.
BP-512 (MV650i/optional) 95 min.
BP-511 (Optional) 95 min.
BP-522 (Optional) 140 min.
BP-535 (Optional) 205 min.
BP-512 BP-522 BP-535
6_D73PAL_E(133-154) 02.12.26 9:32 PM Page 148
149
Ad
ditio
nal
Info
rmatio
n
E
WD-30.5 Wide-converterThis lens decreases focal length by a factor of
0.7, giving you a wide perspective for indoor
shots or panoramic views.
FS-30.5U Filter SetNeutral density and MC protector filters help
you to control difficult lighting conditions.
VL-10Li Battery Video LightThis compact yet powerful video light can be
used for both indoor and outdoor shooting.
The video light is powered by BP-900 series
battery packs.
• Approximate usage time: BP-915: 60 min., BP-930: 120 min., BP-945: 170 min.
• BP-900 series battery packs are charged with the CA-920 Compact Power Adapter.
VL-3 Video LightThis video light enables you to record brightly
in colour even in dark places. It attaches to the
camcorder’s advanced accessory shoe for cable-
free operation.
DM-50 Directional StereoMicrophoneThis highly sensitive, super-directional
microphone attaches to the camcorder’s
advanced accessory shoe. It can be used as
directional microphone (monaural) or stereo
microphone.
WS-20 Wrist StrapUse this for extra additional protection for
active shooting.
MV650i
MV650i
6_D73PAL_E(133-154) 02.12.26 9:32 PM Page 149
150
Ad
dit
ion
alIn
form
atio
n
E
SC-1000 Soft Carrying CaseA handy camcorder bag with padded
compartments and plenty of space for
accessories.
This mark identifies genuine Canon video accessories. When you
use Canon video equipment, we recommend Canon-brand
accessories or products bearing the same mark.
CA
NON GENUINE
VID
EOACCESSOR
Y
6_D73PAL_E(133-154) 02.12.26 9:32 PM Page 150
151
Ad
ditio
nal
Info
rmatio
n
E
Specifications
MV650i/MV630i/MV600i/MV600
7.4 V DC
2.9 W (Using viewfinder), 3.8 W (Using LCD screen)
CCIR standard (625 lines, 50 fields) PAL colour signal
2 rotary heads, helical scanning DV system (Consumer digital VCR SD system); Digital component recording
PCM digital sound: 16 bit (48 kHz/2 ch); 12 bit (32 kHz/4 ch)
1/6“ CCD (charge coupled device), approx. 800,000 pixels (Effective pixels: tape: approx. 400,000 pixels, card*1: approx. 528,000 pixels)
Video cassettes bearing the “MiniDV” mark.
SP: 18.83 mm/s, LP: 12.57 mm/s
SP: 80 min., LP: 120 min.
Approx. 2 min. 20 sec. (with a 60 min. cassette)
MV650i: F1.6-3.6, 22x power zoom, f=2.8-61.6 mm; MV630i: F1.6-3.2, 20x power zoom, f=2.8-56 mm; MV600i/MV600: F1.6-2.9, 18x power zoom, f=2.8-50.4 mm
TTL autofocus, manual focusing possible
1 m, 1 cm on maximum wide angle
1/2,000 sec. (1/250 sec. when using a memory card)
1.6 lx (using the Night mode in CAMERA mode)
More than 100 lx
30.5 mm
0.33 in., TFT colour LCD, approx. 113,000 pixels
2.5 in., TFT colour, approx. 112,000 pixels
Stereo electret condenser microphone
SD Memory Card, MultiMediaCard
Still image: 1024 x 768, 640 x 480 pixelsMovie *2: 320 x 240 pixels (approx. 10 sec.), 160 x 120 pixels (approx. 30 sec.), 12.5 frames/sec.The figures in brackets represent the maximum length of onemovie clip.
1024 x 768: Superfine: 14 images/Fine: 20 images/Normal 39 images; 640 x 480: Superfine: 35 images/Fine 52 images/Normal 86 images
The actual number varies according to the images. Sample images recorded on the supplied SD Memory Card are to be included in the total number.
Design rule for Camera File system (DCF), Exif 2.2 compliant, Digital Print Order Format (DPOF) compliant (still images only)
This camcorder supports Exif 2.2 (also called “Exif Print”). Exif Print is a standard for enhancing the communication between camcorders and printers. By connecting to an Exif Print-compliant printer, the camcorder’s image data at the time of shooting is used and optimised, yielding extremely high quality prints.
Still image: JPEG (Compression mode: Superfine, Fine, Normal), Movie: Motion JPEG
Power supply (rated):Power consumption (AF turned on):Television system:Video recording system:
Audio recording system:Image sensor:
Tape format:Tape speed:Maximum recording time (80 min. cassette):Fast forward/rewind time:Lens:
Focusing system:Minimum focusing distance:Maximum shutter speed:Minimum illumination:Recommended illumination:Filter diameter:Viewfinder:LCD screen:Microphone:Recording media*1:Number of recording pixels*1:
Estimated SD Memory Card SDC-8M capacities*1:
File format*1:
Image format*1:
*1 MV650i/MV630i only *2 MV650i only
6_D73PAL_E(133-154) 02.12.26 9:32 PM Page 151
152
Ad
dit
ion
alIn
form
atio
n
E
Weight and dimensions are approximate. Errors and omissions excepted. Subject to
change without notice.
SDC-8M SD Memory Card8 MB
SD Memory Card standard
0 – 40˚C
32 × 24 × 2.1 mm
2 g
Capacity:Interface:Operating temperature:Dimensions:Weight:
mini-B
Special 4-pin connector (IEEE 1394 compliant)
ø3.5 mm minijackAudio input: -10 dBV/40 kohms or moreAudio output: -10 dBV (47 kohm load)/3 kohms or lessVideo: 1 Vp-p/75 ohms unbalanced
1 Vp-p/75 ohms (Y signal), 0.3 Vp-p/75 ohms (C signal)
ø3.5 mm stereo mini-jack-57 dBV (with 600 ohm mic)/5 kohms or more
ø3.5 mm stereo minijack
0 – 40˚C
103 × 58 × 147 mm
MV650i: 525 g, MV630i/MV600i/MV600: 520 g
USB terminal*1:DV terminal input/output*2:AV terminal input/output*2:
S-video terminal input/output*2:MIC terminal input:
Headphone terminal:Operating temperatures:Dimensions:Weight:
CA-570 Compact Power Adapter100 – 240 V AC, 50/60 Hz
17 W
8.4 V DC, 1.5 A
0 – 40˚C
52 × 90 × 29 mm
135 g
Power supply:Power consumption:Rated output:Operating temperature:Dimensions:Weight:
BP-512/BP-508 Battery PackRechargeable Lithium Ion Battery
7.4 V DC
0 – 40˚C
BP-512: 1100 mAh, BP-508: 800 mAh
38 × 21 × 55 mm
BP-512: 70 g, BP-508: 65 g
Battery type:Rated voltage:Operating temperature:Battery capacity:Dimensions:Weight:
*1 MV650i/MV630i only *2 MV650i/MV630i/MV600i only
6_D73PAL_E(133-154) 02.12.26 9:32 PM Page 152
153
Ad
ditio
nal
Info
rmatio
n
E
Index12bit audio . . . . . . . . . . . . . . . . . . 9716:9 wide screen . . . . . . . . . . . . . . 516-second auto date . . . . . . . . . . . . 83
Abroad, using the camcorder . . . 143Accessories. . . . . . . . . . . . . . . . 7, 148Accessory shoe . . . . . . . . . . . . . . 149Advanced accessory shoe *1 . . . . . 72Analog line-in *3 . . . . . . . . . . . . . . 88Analog-digital converter *3 . . . . . 91Assist lamp*1. . . . . . . . . . . . . . . . . 58Audio dubbing . . . . . . . . . . . . . . . 95Audio mode . . . . . . . . . . . . . . . . . 70Auto . . . . . . . . . . . . . . . . . . . . . . . 56Autofocus . . . . . . . . . . . . . . . . . . . 74AV insert *3 . . . . . . . . . . . . . . . . . . 93AV/DV *3. . . . . . . . . . . . . . . . . . . 91AV/headphones terminal . . . . 37, 69
Backup battery . . . . . . . . . . . . . . . 17Battery charger . . . . . . . . . . . . . . 148Battery pack . . . . . . . . . . . . . . . . . 14Beep . . . . . . . . . . . . . . . . . . . . . . . 51Brightness . . . . . . . . . . . . . . . . . . . 31
Card animation *2. . . . . . . . . . . . 122Card mix *2 . . . . . . . . . . . . . . . . . 121Computer . . . . . . . . . . . . . . . 98, 128Condensation . . . . . . . . . . . . . . . 142Connections - TV . . . . . . . . . . . . . . 39Connections - VCR. . . . . . . . . . . . . 39Copyright signals. . . . . . . . . . . . . . 90Copying still images*2. . . . . . . . . 125
Data code . . . . . . . . . . . . . . . . . . . 82Date and time . . . . . . . . . . . . . . . . 23Date search . . . . . . . . . . . . . . . . . . 84Demo mode . . . . . . . . . . . . . . . . . 52Digital effects . . . . . . . . . . . . . . . . 60Digital zoom . . . . . . . . . . . . . . . . . 28
Direct print function *2. . . . . . . . 117DV dubbing *3 . . . . . . . . . . . . . . . 89DV terminal . . . . . . . . . . . . . . . 87, 98
Easy recording. . . . . . . . . . . . . . . . 56Effects . . . . . . . . . . . . . . . . . . . . . . 64Erasing still images *2 . . . . . . . . . 114Exposure . . . . . . . . . . . . . . . . . . . . 76
Faders . . . . . . . . . . . . . . . . . . . . . . 61Fast forward . . . . . . . . . . . . . . . . . 35File numbers *2 . . . . . . . . . . . . . . 102Focusing . . . . . . . . . . . . . . . . . . . . 74Formatting *2 . . . . . . . . . . . . . . . 127
Grip belt . . . . . . . . . . . . . . . . . . . . 18
Headphones . . . . . . . . . . . . . . . . . 37
Image quality *2 . . . . . . . . . . . . . 100Image stabilizer. . . . . . . . . . . . . . . 68Index screen *2 . . . . . . . . . . . . . . 111
LCD mirror mode . . . . . . . . . . . . . 31LCD screen. . . . . . . . . . . . . . . . . . . 30Lens cap . . . . . . . . . . . . . . . . . . . . 18Light-up buttons *1. . . . . . . . . . . . 50Low light mode. . . . . . . . . . . . . . . 57Low light plus mode *1. . . . . . . . . 58LP mode . . . . . . . . . . . . . . . . . . . . 53
Magnifying the image . . . . . . . . . 81Maintenance . . . . . . . . . . . . . . . . 140Manual focus . . . . . . . . . . . . . . . . 74Memory card *2 . . . . . . . . . . . . . 100Menus . . . . . . . . . . . . . . . . . . . . . . 43Microphone. . . . . . . . . . . . . . . . . . 70
M
L
I
H
G
F
E
D
C
B
A
*1 , *2 *3 Not available with the .MV600MV630iMV650iMV650i
6_D73PAL_E(133-154) 02.12.26 9:32 PM Page 153
154
Ad
dit
ion
alIn
form
atio
n
E
MIC terminal . . . . . . . . . . . . . . . . . 70Movie size *1 . . . . . . . . . . . . . . . . 101MultiMediaCard *2 . . . . . . . . . . . 100Multi-image screen . . . . . . . . . . . . 66My Camera settings . . . . . . . . . . . 49
Night mode. . . . . . . . . . . . . . . . . . 58
Output channel. . . . . . . . . . . . . . . 42
Photo search . . . . . . . . . . . . . . . . . 84Playback - Memory card *2 . . . . . 110Playback - Tape . . . . . . . . . . . . . . . 35Playback pause . . . . . . . . . . . . . . . 37Portrait mode . . . . . . . . . . . . . . . . 57Power adapter . . . . . . . . . . . . . . . 13Print order *2 . . . . . . . . . . . . . . . 115Protect *2 . . . . . . . . . . . . . . . . . . 113
Recording to a VCR. . . . . . . . . . . . 86Record pause mode . . . . . . . . . . . 27Record review . . . . . . . . . . . . . . . . 33Record search . . . . . . . . . . . . . . . . 33Recording Movies (tape) . . . . . . . . 26Recording Movies
(memory card)*1 . . . . . . . . . . . . 108Recording Still Images (tape) . . . . 54Recording Still Images
(memory card)*2 . . . . . . . . . . . . 103Recording programs . . . . . . . . . . . 56Remote sensor. . . . . . . . . . . . . . . . 22Rewind . . . . . . . . . . . . . . . . . . . . . 35
S1 video terminal . . . . . . . . . . . . . 40Sample images *2 . . . . . . . . . . . . 131Sand & Snow mode. . . . . . . . . . . . 57Screen displays . . . . . . . . . . . . . . 133SD Memory Card *2. . . . . . . . . . . 100Search select . . . . . . . . . . . . . . . . . 84Self-timer . . . . . . . . . . . . . . . . . . . 69
Shutter sound *2 . . . . . . . . . . . . . 104Shutter speed . . . . . . . . . . . . . . . . 77Slide show *2. . . . . . . . . . . . . . . . 111SP mode . . . . . . . . . . . . . . . . . . . . 53Speaker . . . . . . . . . . . . . . . . . . . . . 37Sports mode . . . . . . . . . . . . . . . . . 57Spotlight mode . . . . . . . . . . . . . . . 57Still image quality *2. . . . . . . . . . 100Still image size *2 . . . . . . . . . . . . 100Stitch Assist mode *2. . . . . . . . . . 106Super Night mode *1 . . . . . . . . . . 58S-video/S1-video . . . . . . . . . . . . . . 40
Tape protection. . . . . . . . . . . . . . . 21Telephoto . . . . . . . . . . . . . . . . . . . 28Time code . . . . . . . . . . . . . . . . . . . 85Time zone . . . . . . . . . . . . . . . . . . . 23Tripod . . . . . . . . . . . . . . . . . . . . . . 34Troubleshooting . . . . . . . . . . . . . 144TV Screen. . . . . . . . . . . . . . . . 39, 133
USB terminal *2 . . . . . . . . . . . . . . 128
Video. . . . . . . . . . . . . . . . . . . . . . . 39Video heads. . . . . . . . . . . . . . . . . 141Video light. . . . . . . . . . . . . . . 72, 149Videocassettes . . . . . . . . . . . . . . . . 20Viewfinder . . . . . . . . . . . . . . . . . . 18
White balance . . . . . . . . . . . . . . . . 79Wide screen. . . . . . . . . . . . . . . . . . 51Wireless controller . . . . . . . . . . . . 22
Zero set memory . . . . . . . . . . . . . . 85Zooming . . . . . . . . . . . . . . . . . . . . 28
Z
W
V
U
T
S
R
P
O
N
*1 , *2 MV630iMV650iMV650i
6_D73PAL_E(133-154) 02.12.26 9:32 PM Page 154
CANON INC.
Canon Europa N.V.P.O. Box 2262, 1180 EG Amstelveen, the Netherlands
Canon UK Ltd.Ribcon WayLuton Bedfordshire LU4 9URTelephone 0870-241-2161
Canon Australia Pty. Ltd1 Thomas Holt Drive, North Ryde, N.S.W. 2113, AustraliaTelephone 805-2000, Fax 887-4484
Canon New Zealand LtdAkoranga Business Park, Akoranga Drive, Northcote, Auckland, New Zealand Telephone: 489-0300, Fax: 489-0380
Canon Singapore Pte. Ltd79 Anson Road #09-01/06, Singapore 079906Telephone (65)-532-4400, Fax (65)-221-2939
Canon Hongkong Company Ltd9/F, The Hong Kong Club Building, 3A Chater Road, Central, Hong Kong
Canon Latin America, Inc.Sales & Enquiries: 703 Waterford Way Suite 400 Miami, FL 33126 USA
Printed on 100% reused paper.
0035W681PUB.DIE-181 © CANON INC. 20030000A/AB0.0 DY8-9020-115-000 PRINTED IN JAPAN
0_D73PAL_E(cover) 02.12.26 9:17 PM Page 1