Introduc The D anGroen Mattachingmechanisand instrof orienticover. 1.0 R 1.1 Uhardware

1.2 R

ction:

nd DL Tiltingodel D or DL

g the hinge msm, a “U” shructions for fng the cove

Riser Bracke

Unpack the ce.

Remove the f

IN

P

g Kettle PowL Kettle. Thmechanism ahaped riser, ield installatr on top of th

et Installatio

cover and co

four hole plu

NSTRUC

D and DPower-Aid

Assemb

er-Aid Covehe kits includand a bent rand a hardwion. The insthe kettle and

on

omponents a

ug caps in th

Page 1

CTION S

DL Tilting Kd (#51) Cobly and Moun

r Kits are shde a spun starod handle, aware kit with tructions beld securing th

and locate th

he left trunnio

SHEET

Kettle over Kit nting

hipped compainless steela spring-assitems needelow will guidhe assembly

he U-shaped

on plate.

plete for fieldl disk cover

sisted power ed for attach

de you througy bracket to t

d riser bracke

146551 Re

d installation with studs foaid hinge

hing the covegh the procethe pedesta

et and moun

ev. B

on a or

er ess l

nting

1.3 A

1.4 Alock wasnuts to a

Align the rise

Align the holehers and nu20 ft/lb torq

r to the hole

es in the risets to secureue with a 3/

es in the trun

er bracket to the bracket8” open end

Page 2

nnion plate a

the cover at to the coved or socket w

as shown.

s shown ander, gasket anwrench.

d install the nd backing p

146551 Re

mounting bolate. Tighte

ev. B

olts, en the

2.0 A 2.1 AAssemblenough f

2.2 Alocking cin/lb torq

Actuator and

Align the stude the fenderfor adjustme

Assemble thecompound anue with a 1/4

d Cover Ins

ds on the covr washers an

ent.

e actuator tond the dome4” open end

tallation an

ver actuatornd nuts to th

o the three ste nuts suppli or socket w

Page 3

nd Adjustme

r to the holese underside

tuds on the ded in the co

wrench.

ent

s in the top oe of the actua

domed coveover kit. Tigh

of the riser bator, but leav

er and securhten the dom

146551 Re

bracket. ve them loos

re using threme nuts to 20

ev. B

se

ead 0

2.3 Ekettle. Adfour nutswrench.

2.4 Inlocking c

2.5 Aa 20 ft/lb

Ensure the kedjust the mos securing th

nstall the hancompound to

Attach the hatorque and

ettle is tilted unting bracke actuator to

ndle spacerso the ends of

andle over ththen install t

to the full upket to align to the riser to

s over the twf the two stu

he spacers athe red ball

Page 4

pright positiohe cover ove

o a 10 ft/lb to

wo studs at tds.

and secure won the hand

on and then er the kettle orque with a

the front of th

with two domdle end.

lower the coand then fu1/4” open e

he cover and

me nuts. Tig

146551 Re

over over theully tighten thend or socke

d apply thre

hten the nut

ev. B

e he et

ad

ts to

2.6 Atwo 3/4”

2.7 T

Adjust the tenopen end w

The complete

nsion in the renches.

ed Power-Ai

actuator ass

d cover asse

Page 5

sembly by tu

embly shoul

urning the ad

d look as sh

djusting nuts

hown below:

146551 Re

s as shown.

ev. B

Use

146551 Rev. B Page 6

1055 Mendell Davis Drive, Jackson, MS 39272 • 888.994.7636 • 888.864.7636 • unifiedbrands.net ADDITIONAL MANUFACTURING LOCATION: 525 SOUTH COLDWATER ROAD, WEIDMAN MI 48893

© 2009 Unified Brands. All Rights Reserved. Unified Brands is a wholly-owned subsidiary of Dover Corporation.