Post on 13-Jan-2017
IMPROVEMENT DESIGN OF SOLAR CHIMNEY
TEY NGUAN WUI
Bachelor of Engineering with Honors
(Mechanical and Manufacturing Engineering)
2008
IMPROVEMENT DESIGN OF SOLAR CHIMNEY
TEY NGUAN WUI
This project is submitted in partial fulfillment of the requirements for the degree of Bachelor of
Engineering with Honors
(Mechanical and Manufacturing Engineering)
Faculty of Engineering
UNVERSITY MALAYSIA SARAWAK
2008
Dedicate to:
My Beloved Family
And Friends
UNIVERSITI MALAYSIA SARAWAK
BORANG PENYERAHAN TESIS
Judul: IMPROVEMENT OF SOLAR CHIMNEY DESIGN .
.
SESI PENGAJIAN : 2008/2009
Saya TEY NGUAN WUI .
(HURUF BESAR)
mengaku membenarkan tesis * ini disimpan di Pusat Khidmat Maklumat Akademik, Universiti
Malaysia Sarawak dengan syarat-syarat kegunaan seperti berikut:
1. Tesis adalah hakmilik Universiti Malaysia Sarawak.
2. Pusat Khidmat Maklumat Akademik, Universiti Malaysia Sarawak dibenarkan membuat salinan
untuk tujuan pengajian sahaja.
3. Membuat pendigitan untuk membangunkan Pangkalan Data Kandungan Tempatan.
4. Pusat Khidmat Maklumat Akademik, Universiti Malaysia Sarawak dibenarkan membuat salinan
tesis ini sebagai bahan pertukaran antara institusi pengajian tinggi.
5. ** Sila tandakan (√) di mana kotak yang berkenaan
SULIT (Mengandungi maklumat yang berdarjah keselamatan atau
kepentingan Malaysia seperti yang termaktub di dalam AKTA
RAHSIA RASMI 1972).
TERHAD (Mengandungi maklumat TERHAD yang telah ditentukan oleh
organisasi/badan di mana penyelidikan dijalankan).
TIDAK TERHAD
Disahkan oleh
_________________________ ___________________________
(TANDATANGAN PENULIS) (TANDATANGAN PENYELIA)
Alamat tetap: 166, LRG Poh Kwong 3 Ir Dr MOHD. SHAHRIL OSMAN
Poh Kwong Park,
93150 Kuching,
Sarawak.
Tarikh: __________ Tarikh: __________
CATATAN * Tesis ini dimaksudkan sebagai tesis bagi Ijazah Doktor Falsafah, Sarjana, dan Sarjana Muda.
** Jika tesis ini SULIT atau TERHAD, sila lampirkan surat daripada pihak berkuasa/organisasi
berkenaan dengan menyertakan sekali sebab dan tempoh tesis ini perlu dikelaskan sebagai SULIT atau
TERHAD.
√
R13a
Approval Sheet
This Final Year Project attached here:
Title : IMPROVEMENT OF SOLAR CHIMNEY DESIGN
Student Name : TEY NGUAN WUI
Matrix No : 15420
Has been read and approved by:
_____________________ _ _________________
Ir Dr MOHD. SHAHRIL OSMAN Date
(Supervisor)
Date
(Internal Reader)
ii
ACKNOWLEDGEMENT
I would like to express his appreciations to whom have lent a hand in bringing
this project to a success within the given time frame.
Firstly, the author would like to thanks his supervisor, Ir Dr Mohammad Shahril
Osman for all his guidance and support provided throughout this project to ensure project
is carried out successfully with least obstacles.
Secondly, special thanks to the laboratory technicians including Mr. Masri Zaini,
Mr. Mohd. Rhyier Juen Abdullah and Madam Hasmiza Kontet are acknowledged on the
lab equipment advices, machineries operation method and technique supports.
The author would like to express his gratitude to his friends and fellow course
mates for their help and support throughout the project.
Lastly, the author family support is acknowledged for bringing this project to
move on until a success is achieved.
iii
ABSTRACT
Renewable energy has become more preferable to the society compare with
conventional energy. This project presents the design, fabrication and performance
analysis of the improved solar chimney power generator. The solar chimney apply hot air
rise concept to generate power. The design consists of a chimney tower connected on top
of the circular solar collector with a chimney support. Within the chimney tower lie two
generators, one above another to generate power. Below of the solar collector lays the
heat absorber tiles and water tubes. The water tubes absorb heat during the day time, and
release the heat during the night for the power generation. An air flow director is placed
below the chimney tower to direct the air into the tower and then turn the electrical
generators. In this project, air flow simulation and fabrication method were employed.
The performance of the solar chimney is dependent to the solar radiation, solar collector’s
size, chimney tower’s height, collector’s transparency and type of heat absorber. The
night operation performance is dependent on the water tube and heat absorber type. The
solar chimney is 4.2 meter diameter and 3.6 meter height. The simulation will simulate
the air behaviors within the solar chimney.
Keyword: Solar chimney, renewable energy
iv
ABSTRAK
Tenaga yang boleh diperbaharui semakin mendapat tempat di hati masyarakat
berbanding dengan tenaga yang tidak boleh diperbaharui. Projek ini bertujuan untuk
mengetengahkan reka bentuk, pembuatan serta analisa terhadap prestasi penjana kuasa
cerobong suria yang telah dipertingkatkan. Cerobong suria ini menggunakan konsep
udara panas untuk menghasilkan tenaga. Reka bentuknya terdiri daripada menara
cerobong yang dihubungkan dengan penyokong cerobong di atas pengumpul suria
berbentuk bulat. Terdapat dua penjana di dalam cerobong suria, bertindih di antara satu
sama lain untuk menjana tenaga. Di bawah pengumpul suria terdapat jubin penyerap haba
dan tiub air. Tiub air ini berfungsi untuk menyerap haba pada siang hari dan
membebaskan haba pada waktu malam untuk penjanaan tenaga. Sebuah pengarah aliran
udara diletakkan di bawah menara cerobong untuk mengarahkan aliran udara ke menara
dan kemudian memutarkan penjana electrik. Dalam projek ini, simulasi aliran udara dan
cara pembuatan diambil kira. Prestasi cerobong solar bergantung kepada radiasi solar,
saiz pengumpul solar, tinggi cerobong solar, kelutsinaran pengumpul dan jenis penyerap
haba yang digunakan. Prestasi pada waktu malam bergantung kepada tiub air dan jenis
penyerap haba. Cerobong asap inimempunyai diameter sebanyak 4.2 meter dan
berketinggian 3.6 meter. Simulasi akan digunakan untuk mengetahui kelakuan aliran
udara dalam cerobong suria.
v
TABLE OF CONTENTS
CONTENT Page
ACKNOWLEDGEMENT………………………………………………………. ii
ABSTRACT……………………………………………………………………… iii
ABSTRAK……………………………………………………………………….. iv
TABLE OF CONTENT…………………………………………………………. v
LIST OF TABLES……………………………………………………………….. ix
LIST OF FIGURES………………………………………………………………. x
NOMECULATURE….………………………………………………………….. xiii
CHAPTER 1 INTRODUCTION TO THE SOLAR CHIMNEY
1.1. Introduction………………………………………………………………… 1.
1.2. Objectives of the Project…………………………………………………... 3.
CHAPTER 2 LITERATURE REVIEW
2.1. Introduction ……………………………………………………………….. 4.
2.2. Solar Chimney Working Principle…………………………………………. 5.
2.3. Solar Chimney’s Structure…………………………………………………. 9.
2.3.1. Chimney Tower……………………………………………………………. 10.
vi
2.3.2. Turbine ……………………………………………………………………. 17.
2.3.3. Solar Collector…………………………………………………………….. 20.
2.3.4. Heat Absorber …………………………………………………………….. 28.
2.3.5. Water Tubes………………………………………………………………... 32.
2.4. Environment Factor Consideration………………………………………... 33.
2.4.1. Solar Radiation……………………………………………………………. 33.
2.4.2. Air Humidity …………………………………………………………….. 34.
2.4.3. Star-CD software ………………………………………………………….. 35.
CHAPTER 3 METHODOLOGY
3.1. Introduction……………………………………………………………….. 36.
3.2. Method and Approaches…………………………………………………... 37.
3.3. Work Plan………………………………………………………………….. 39.
3.4. Future Work……………..…………………………………………………. 41.
CHAPTER 4 ANALYSIS AND DESIGN OF THE SOLAR CHIMNEY
4.1. Introduction………………………………………………………………... 42.
4.2. Air Flow Simulation Analysis………………………………………………43.
4.2.1. Air flow director analysis……………………………………………………44.
4.2.1.1.Without air flow director analysis…………………………………………..44.
4.2.1.2.With air flow director analysis……………………………………………... 46.
4.2.2. Nozzle Design analysis…………………………………………………….. 49.
4.2.2.1.Nozzle Design Pattern 01 analysis…………………………………………..49.
4.2.2.2.Nozzle Design Pattern 02 analysis…………………………………………..51.
vii
4.2.3. The Turbine’s blades Design analysis………………………………………52.
4.2.3.1.The turbine’s blade design pattern I and II………………………………….53.
4.2.4. Overall Simulation analysis………………………………………………….54.
4.3. Solar Chimney Parts Design and Modification……………………………. 57.
4.3.1. Power Generator design ……………………………………………………..57.
4.3.1.1.Turbine Shaft………………………………………………………………...58.
4.3.1.2.Turbine’s Blades ……………………………………………………………59.
4.4.1. Power Generator……………………………………………………………..61.
4.4.2. Gear System………………………………………………………………….61.
4.4.3. Water Tube………………………………………………………………….63.
4.4.4. Collector Skirt……………………………………………………………… 63.
4.5. Conceptual Solar Chimney Design………………………………………… 64.
4.5.1. Conceptual Design 1……………………………………………………….. 64.
4.5.2. Conceptual Design 2……………………………………………………….. 66.
4.6. Assembly Process………………………………………………………….. 67.
4.7. Summary…………………………………………………………………… 70.
CHAPTER 5 RESULT AND DISCUSSION
5.1. Introduction………………………………………………………………… 71.
5.2. Air Temperature Variation Analysis in Solar Chimney…………………….72.
5.3. Water Tube Analysis in Solar Chimney…………………………………….75.
5.4. Solar Collector Skirt analysis………………………………………………..78.
5.5. Discussion …………………………………………………………………..79.
5.6. Conclusion ………………………………………………………………….82.
viii
CHAPTER 6 CONCLUSION AND RECOMMENDATION
6.1. Conclusion…………………………………………………………………. 83.
6.2. Recommendations …………………………………………………………. 85.
REFERENCE…………………………………………………………………….. 88.
APPENDIX.............................................................................................................. 90.
ix
LIST OF TABLES
Table 2.1: Pressure difference and wind velocity versus power output (P2)………. 17.
Table 2.2: Annual power output comparison, which illustration the influence
of the including a better quality glass for the collector roof……. ……... 22.
Table 2.3: Annual power output comparison for solar chimney power plant
employing various ground types……………………………………….. 29.
Table 4.1: Material comparison for the turbine shaft ……………………………... 59.
Table 4.2: Material comparison for the turbine’s wing……………………………. 60.
Table 4.3: Material comparison of power generator ………………………………. 61.
x
LIST OF FIGURES
Figure 2.1: Sea Breeze……………………………………………………………... 5.
Figure 2.2: Solar chimney operation concepts…………………………………….. 7.
Figure 2.3: Principle of heat storage underneath the roof using water filled
black tubes…………………………………………………………….. 8.
Figure 2.4: Solar chimney’s structure……………………………………………… 9.
Figure 2.5: Influence of the tower height on the average temperature in
the tower……………………………………………………………….. 11.
Figure 2.6: Standard atmospheric and isentropic specific volumes………………... 12.
Figure 2.7: Influence of the tower radius on the mass flow……………………….. 14.
Figure 2.8: Influence of the tower radius on the velocity of the tower
symmetry axis………………………………………………………….. 14.
Figure 2.9: Solar chimney turbine layouts…………………………………………. 19.
Figure 2.10: Schematic drawing of horizontal-to-vertical transition section
(a) without and (b) with a centerpiece to redirect the flow…………… 20.
Figure 2.11: Effect of the inclusion of a better quality glass for the
collector roof…………………………………………………………. 21.
Figure 2.12: Influence of collector material on the ground temperature…………... 23.
Figure 2.13: Influence of collector material to the flow velocity in the tower…….. 23.
Figure 2.14: Influence of collector radius on the average temperature in the
solar collector…………………………………………………………. 24.
xi
Figure 2.15: Influence of the collector height on the development of the
mass flow……………………………………………………………... 25.
Figure 2.16: Influence of the collector height on the average temperature
in the tower.…………………………………………………………... 26.
Figure 2.17: Comparison between the original and new convective heat
transfer coefficients…………………………………………………... 30.
Figure 2.18: Thermal networks for a solar chimney collector…………………….. 32.
Figure 3.1: Conceptual drawing of the new method proposed……………………. 37.
Figure 3.2: Three main parts of chimney for ease of modification……………….. 40.
Figure 4.1: Air flow velocity analysis without the flow director …………………. 45.
Figure 4.2: Air flow pressure analysis without the flow director…………………. 46.
Figure 4.3: Air flow velocity analysis with air flow director……………………… 47.
Figure 4.4: Air flow pressure analysis with air flow director……………………… 48.
Figure 4.5: Air flow velocity analysis with nozzle design pattern 01……………... 50
Figure 4.6: Air flow pressure analysis with nozzle design pattern 01…………….. 50.
Figure 4.7: Air flow velocity analysis with nozzle design pattern 02……………... 51.
Figure 4.8: Air flow pressure analysis with nozzle design pattern 02…………….. 52.
Figure 4.9: Pressure analysis of turbine’s blade design pattern 1…………………. 53.
Figure 4.10: Pressure analysis of turbine’s blade design pattern II……………….. 54.
Figure 4.11: Velocity analysis at Part I and Part II …………………………........... 55.
Figure 4.12: Velocity analysis whole systems…………………………………….. 56.
Figure 4.13: Second generator parts design in conceptual design 1……………….. 65.
Figure 4.14: Overall conceptual design 1…………………………………………...66.
xii
Figure 4.15: Second generator part design in conceptual design 2………………… 67.
Figure 4.16: Flow of solar chimney structure assembly process………………….. 69.
Figure 5.1: Temperature variant across solar collector ……………………………. 73.
Figure 5.2 Temperature on the solar collector near the perimeter…………………. 74.
Figure 5.3: Temperature on the solar collector near the center……………………. 75.
Figure 5.4 Temperature under solar collector (i) with skirt, (ii) without skirt…….. 78.
xiii
NOMECULATURE
Latin
𝑝 Pressure
𝑉 Wind velocity
𝑣 Volume
𝜌 Density [kgm-3
]
𝑒 Maximal net work output [J/kg]
ŋ Efficiency
𝐻 Stagnation enthalpy
Convection heat transfer coefficient [W/m2K]
𝑓 Friction factor
𝑅𝑒 Reynolds number
𝑃𝑟 Prandtl number
𝑘 Thermal conductivity [W/m K]
𝑑 Diameter
𝜇 Dynamic viscosity [kg/m s]
𝑔 Gravitational acceleration
𝑐 Specific heat coefficient
𝑇 Temperature
𝑁 Number of gear tooth
𝑤 Gear speed
xiv
𝑅 Gear ratio
𝑄 Heat energy
𝑐 Specific heat capacity
𝜃 Temperature gradient
Prefix
∆ Change in value
Subscript
𝐻𝑐 Chimney height
𝑎 Atmosphere
𝑐𝑜𝑙𝑙 Collector
𝑡𝑜𝑡 Total
𝑡𝑡 Circumferential component
𝑡 Total (stagnation) or turbine
𝐿𝑜𝑠𝑠 Loss
𝑟 Collector roof to air under collector roof
Air under collector roof or hydraulic
𝑟𝑎 Collector roof to ambient air
𝑚 Mean
𝑝 Pressure
𝑀 Motor
𝐷 Driven
1
CHAPTER 1
INTRODUCTION TO SOLAR CHIMNEY
1.1. Introduction
Solar chimney generator is a hybrid system of solar and wind energy,
which are using convection of air heated by passive solar energy generate electric
energy. It is also referred as the thermal chimney.
By considering all forms of energies options available, renewable energy
has become more preferable to the society compare with conventional energy
resources such as petroleum, coal and natural gas. The solar chimney is an
alternative source because it is cheap and green energy, which is affordable for
developing country and preferable for advanced country that demand for
unpolluted and stable price energy. This renewable energy fulfills the demand of
the society to achieve a better, healthier and safer life style.
Solar chimney is getting the attention due to the new renewable power
generator that meets the current demand. Researchers are interested in this sector
2
and many researches were conducted, but the efficiency of the renewable energies
is still not running at its efficient state.
The solar chimney was first originated by German author, Hanns Günther
in 1931. In Manzanares, (Spain), a small scale working model of solar chimney
was successfully built by Prof. Dr. Ing. Jörg Schlaich, Bergerman and Partner. In
1982, the chimney had a diameter of 10 meters and height of 195 meters, with a
collection area (greenhouse) of 46,000m2 (about 11 acres) obtaining a maximum
power output of about 50kW. The solar chimney function around 8 years before it
was destroyed in a thunderstorm. Before the incident happened, the optimization
data was collected and was lincensed to EnviroMission and SolarMission
Technologies Inc. USA.
Solar chimney power plant consists of transparent glass canopy roof raised
a certain height from the ground and surrounding the black chimney circular
tower. Inside the chimney tower lays one or more turbo-generators at its center
base. Black color heat absorber is laid and the water tubes are place between the
heat absorber to allow night tie power generation.
Current prototype has a chimney tower of 3.6 meter height. Inside the
chimney tower lie two generators, a nozzle is installed for the second generator to
function using water mill concept. The chimney tower is built on circular solar
3
collector, which is connected by a chimney support. The solar collector is 4.2
meter in diameter. The solar collector is raise 15 millimeter from the ground and
incline till 50 millimeter. Below the collector lie the black heat absorber tiles and
water tubes. Water tubes absorb heat during the day time and release it at night
time for plant operation.
1.2. Objective of the project
Objectives of this project are to made modification on the existing solar
chimney. To do so, the chimney will be reassembled. Some parts of the current
chimney will be improved such as the main generator and chimney tower. For
modifications part, the processes include reducing the air leakage from the
chimney, to improve power output by studying the generator and implementation
of water tube. Then simulation will be applied to the modified chimney. Lastly
testing will be run to observe the overall performances. All those are to increase
the solar chimney efficiencies.
4
CHAPTER 2
LITERATURE REVIEW
2.1. Introduction
Since the year electricity was discovered, the demand of electricity has
been increasing. Societies now no longer just demand for simple electricity, they
also demand for environment friendly energy or so called the green energy. Green
energies that that are common found are the hydroelectricity, geothermal, wind
power generator and photovoltaic cell. Another green energy that researcher are
interested recently is the solar chimney power generator. This chapter contains the
literature review of some researches done previously by various researchers
regarding solar chimney power generator. In this chapter also, the working
concept, the solar chimney structure, and environment factors to be consider will
be discuss.
5
2.2. The Working Concept of Solar Chimney
The working principle of the solar chimney is actually originated from the
natural occurrence of hot air rises. An easy illustration of this concept is by
considering the sea breeze, which is shown in Figure 2.1.
Figure 2.1: Sea Breeze
The sun heated up both land and sea. Land heats up faster than sea to
higher temperature, causing the air on the surface of the land hotter than air on the
surface of the sea. The hot air on the surface of land raises and creates a low
pressure condition on the land surface. Air on sea surface, which experience
higher pressure, will move toward the lower pressure land surface replacing the
raised hot air. While moving from sea to land surface, the air is being heated by
the hot land temperature and hence the air will rise again, creating an infinite
6
cycle. This cycle result a steady wind moving from sea to land and that is
basically the sea breeze theory.
In the solar chimney, the heat absorber will heated up faster than it‟s
surrounding; causing the air on the surface of the heat absorber to raise and flow
toward the chimney tower. At the same time, the pressure on the heat absorber
surface will drop to a point which lowers than the surrounding pressure. Hence
cool air from the surrounding which has higher pressure will flow into the solar
collector, due to air flow from high pressure to low pressure area. While the cool
air flow in solar collector, it will slowly heated up by the heat from the heat
absorber. Cool air temperature rises across the heat absorber and finally flows out
through the chimney tower. The air flow through the chimney tower will be
harvest by the generator turbines and generates electricity. This concept is
illustrated in Figure 2.2.
During the day, heat absorber and water tube were heated up together.
When come to night time, the heat collected in the water will be released to
continue heating up the surface air as to replace the heat absorber. Heat release
from the water tube heated up the surface air to a higher temperature causing them
to rise. This creates a pressure difference between the air inside the solar collector
and the surrounding, hence wind flow created between these areas. Cool air
moving into the solar collector is slowly heated up by the heat released from the