Go For The Grommets

Grommet Drapery Designs

• Banding on Leading Edge

• Fabric on bottom of drapery

Grommet Drapery Designs

• Puddle or Just Too Long?• How do you determine

the length?

Grommet Drapery Designs

Grommet Drapery Designs

Grommet Drapery Designs

Grommet Valance with Stationary Panels

Grommet Drapery Designs

Draperies With Sheer Fabrics

Grommet Drapery Designs

Two Finger Pleated Grommet Draperies

Grommet Drapery Designs

Sunbrella Outdoor

Draperies

Grommet Drapery Designs

Can You Create Grommet Draperies ?

Measuring the WindowMeasure the width of your window treatments, taking into account if you want to mount hardware on the wall or directly on the window trim.

Allow 1 1/2" - 3" on each side of the window for when the drapes are completely open.

Be sure to consider extra wall space needed for decorative finials, as the rod dimensions do not include additional width added by each finial.

To make the windows appear larger, mount the curtain rod 6" above the trim and allow the rod width to extend 3" beyond the window's actual width.  

How to Determine Drapery Length

Grommets are placed ½” to 1” from the top of the drapery.Measure from top of rod to floor to determine the length + ½” to 1” allowed at the top.Deduct the ½ inch from the bottom unless drapery is going to touch the floor.

Rod Height

Floor

Installing Hardware

Bottom of drapery rod should be 4” to 6” above the top of the window.

You can hang the rod as high as you would like.

Grommets are 1 5/8”

inside diameter and the rod should be small enough to allow movement of the drapery.

Selecting & Calculating Yardage

• Vertical Repeat 22”

• Horizontal Repeat 13.5”

• 54” Wide Fabric

• Fullness of drapery fabric should be 1.75 to 2.25 times the finish width of the drapery

Formula for Calculating Yardage

1. Example - Finished Length 100” - Finished Width 90”

2. Length – add 6” for hem and 2” to fold down at top of drapery

3. Cut length would be 108”

4. Fullness – Finished width 90” x 2.25 = 202.5” Plus side hems of 6” = 208.5”

5. Divide by fabric width of 54” = 3.86 width or 4 widths of fabric

6. 4 Widths x 108” = 432” divided by 36” (1 yard) = 12 yards

7. Repeat is 22.5” which requires 4.8 repeats for finish length – I would order 13 yard for matching

SEW OR NO SEWSew grommet tape to drapery or use Sealah Tape (Machine Washable)

We recommend sewing for all out door draperies because of the environment.

Grommet Supplies

Grommet Tape $6.99 a yard

Grommet Supplies

Grommet Tools

NO SEW Grommet Draperies

• Use ½” to ¾” Sealah Tape or a Iron-on Adhesive Tape

• Place adhesive tape on both sides of the Grommet tape.

NO SEW Grommet Draperies

1. Tape lining and fabric together at top edge of fabric

2. Fold top edge over ¾”

NO SEW Grommet Draperies

Lay Grommet tape on to fabric with adhesive side on fabric Pin in place before removing adhesive tape

NO SEW Grommet Draperies

Slowly remove adhesive tape on each edge of the grommet tape

NO SEW Grommet Draperies

Leave grommet tape in place while peeling the adhesive from the bottom

NO SEW Grommet Draperies

1. Important tip! Make sure ring connector is at the out side end of each side hem of your drapery2. Now it’s time for fold your side hems – fold 1 ½” twice for the side hem ( I recommend cutting the selvage off the Fabric)

NO SEW Grommet Draperies

You may sew the grommet tape to the top of the drapery

NO SEW Grommet Draperies

Now it is time to start cutting the fabric from the grommet wholes

NO SEW Grommet Draperies

Use an 18mm olfa rotary cutter to cut around the inside of the grommet circle.

NO SEW Grommet Draperies

With a rubber mallet, tap the grommet into the drapery

NO SEW Grommet Draperies

Using grommet tape holds the folds in place; there will be no need for continuously dressing your draperies.

Sew in the Sun!623-878-7350

Peoria, AZ

www.HomeFashionsU.comhomefashionsu@gmail.com