Post on 10-Apr-2018
8/8/2019 Folding Room Divider
1/5
PHOTOS
BYSTAFFANDSCOTTJACOBSON
10 American How-To
Simple lines and keen
attention to detail
make this oak divider
a welcome addition to
any room. Coordinate
the removable screen-
ing fabric panel with
your own upholstery
for a truly custom look.
Todays popular residential floor plans empha-size larger rooms and more open space. Whilethese barrier-free designs are liberating, they cancomplicate furniture placement and make distin-guishing spaces for particular functions difficult.
This folding room divider project provides a sim-ple yet elegant solution.
When American How-To asked me to design a
divider that would work within various types ofhomes contemporary, traditional, eclectic Iturned to the Arts and Crafts period for inspira-tion. As for my choice of woods, I used red oak
because oak still is Americas most popular resi-dential wood for natural trim, floors and cabi-netry. However, you could use any hardwoodand achieve the same beautiful results.
Making the partsI started with 6/4 stock and planed it to a uni-form 1-1/4-in. thickness. This stock is readily
available from lumberyards that sell hardwoods.Begin by ripping the 1-1/4-in. stock to width
for the rails and stiles using your table saw andfence. Then crosscut both the rails and stiles to
length using the sawsmiter gauge, or use amiter box.
To keep this projectuncomplicated, I joinedthe rails and stiles with1/2-in.-dia. dowels.
Although dowel joints aresimple, aligning dowelsproperly can be difficultunless you use an accu-rate doweling jig. For thisproject, I chose to makemy own simple tandem
jig (see drawing) becausethe spacing betweendowel holes is the samefor all the parts.
To ensure jig accura-
cy, I made it from thesame 1-1/4-in. stock asthe rails and stiles. Ibored the holes using abrad-point bit mountedin a drill press. Then Iattached the 1/4-in. ply-
wood sides to the jig withglue and small nails.
Lay out and mark theposition of the rails onthe stiles. Use thesemarks to correctly locatethe doweling jig. Secure
Folding Room DividerTame an open floor plan to add privacy
WORKSHOPby NEAL BARRETT
8/8/2019 Folding Room Divider
2/5X American How-To
1-1/4 x 1-3/4 x
2-1/4" hardwood
1/4"1-1/4"
1/4"
7/8"
1-3/4" 1/2"1/2"
1/4"
Set in 1/8"
16"
1/4"
1/4 "
3"
1/2"
1/4"
1-1/4"
1-1/4 x 2"double-actionhinge(6 req'd.)
1/2"
1-1/4"
2-1/4"
2-1/4"
1-1/4"
No. 4 x 1"
brass fhws
No. 4x 3/4"brass
fhws
1/2" dia. x 2" fluteddowel (typ.)
Notch both ends
5"
1/4 x 2-1/4 x 3-1/4"plywood (2 req'd.)
1/2" dia.throughholes
Bore 1/2" dia. x 1-1/16"-deep dowel holes (typical)
42-1/2
Stops
Stops
Stops
GridScreenfabric
Grid
Screenfabric
Grid
SECTION VIEW
DOWELING JIG FRONT VIEW DETAILS
GRID MEMBERS F AND G
A
A
A
A
A
A A
B
B
B
C
C
C
D D
D
E
E
E
E
E
F
I
G
G
H
H
F
ROOM
DIVIDER
12 American How-To
8/8/2019 Folding Room Divider
3/5
the jig to the stock with a C-clamp andclamp the stock in your workbench vise(see photos) before boring the holes.Indicate the correct drilling depth by
wrapping masking tape around thebit. Its a good practice to drill about
1/16 in. deeper than necessary to besure the joint can close and to allowroom for excess glue.
Be sure to leave the jig and work-pieces oriented in the same direction as
you bore the holes. Any minor inaccu-racies in the jig will be magnified if youchange its relative position from one
workpiece to the next. Test fit eachjoint with dowels before you glue (seephoto). If the dowels are too fat for theholes, you can pare down the dowels
with a simple jig. Drill a 1/2-in.-dia. holethrough a 1/8- or 1/4-in. steel plate,then drive the dowels through the hole
with a mallet.
The plywood panel of each frame fitsinto a 1/4 x 1/4-in. groove you cut inthe stiles and the bottom and middle
rails before assembly. Use a plungerouter to cut the groove with a 1/4-in.-dia. straight bit and an edge guide. Tohelp support the router base, I clampanother piece of stock in the bench visenext to the stile (see photo).
To cut the tongues on the edges ofthe plywood panels, use a router andpiloted rabbeting bit or make the cuts ona table saw. If you set a 1/8-in.-kerf blade1/8 in. from the fence and 1/4 in. high,
you can make all the rabbet cuts withoutchanging the fence position. Make thefirst cuts with the panel face against thefence, then make the cuts with the panelface down on the saw table.
Assembling the frameTo assemble a frame, apply and spreadglue on each dowel and in each dowel
hole. If you use polyurethane glue, as Idid for more open time, apply glue onlyon the walls of the holes. Do not gluethe panel; let it float free in the grooves.
Although theres no danger of the ply-wood panel expanding and contractinglike a solid wood panel, gluing it is
unnecessary and it can create a mess.Install the three rails in one stile;
then slide the panel into position. Alignthe remaining stile over the dowels,then clamp. Compare diagonal measure-ments to be sure that the frame issquare and adjust the clamps as needed.
Making the screensAlthough I made only one grid for eachdivider section, you might want to maketwo (so the fabric is sandwiched betweenthem) if you plan on using the divider ina spot where both sides are visible.
September/October 1999 13
SHOPPING LIST
25 bf 6/4 red oak
3/4 x 24 x 24 red oak plywood (1)
Double action hinges (six reqd.,
Rockler catalog No. 29041)
No. 4 x 3/4-in. brass flathead
wood screws
No. 4 x 1-in. brass flathead
wood screws
1/2-in.-dia. x 2-in. fluted dowels
Synskin fiberglass fabric
(2 yds.; see SOURCES)
MATERIALS AND CUTTING LIST
KEY NO DESCRIPTION SIZE
A 6 Stiles 1-1/4 x 1-3/4 x 66 in.
B 3 Top rails 1-1-4 x 2-1/4 x 12 in.
C 3 Mid rails 1-1/4 x 2-1/4 x 12 in.
D 3 Bottom rails 1-1/4 x 3 x 12 in.
E 3 Panels, oak plywood 3/4 x 12-1/2 x 16-1/2 in.
F 18 Vertical grid/stop strips 1/2 x 1/2 x 42-1/2 in.
G 12 Horizontal grid strips 1/2 x 1/2 x 12 in.
H 6 Horizontal stop strips 1/2 x 1/2 x 11 in.
I 3 Screen fabric 14 x 44 in.*
*Use the assembled grid as a template to trim to exact size; see
text and SOURCES.
DOWELING
To ensure that the joints fit well, keep the
jig and the workpieces oriented in the
same position relative to one another.
Secure the workpiece in a bench vise andthe jig to the work with a C-clamp. Mark
the drilling depth on the bit with tape.
Fit the frame parts together temporarily
and use a pencil to mark the location of
the groove for the panel.
8/8/2019 Folding Room Divider
4/5
tions. Gang cut the joints on your tablesaw using a stack-dado blade and a slid-
ing table (see photo). A wobble-dadoblade will produce a cut thats toocoarse. The joints should fit snugly andbe flush on both sides. Youll probablyneed to make several test cuts beforethe joints fit just right.
Dry-assemble each grid to check forproper fit. For a fast set, apply yellow
glue to each joint andclamp (see photos). Whenthe glue has dried, sand
each grid with 220-gritsandpaper and apply aclear finish, such as var-nish or lacquer.
I used a translucentfiberglass fabric common-ly used as a shoji screenmaterial to cover the grid(see SOURCES). Otherfabrics or rice paper wouldalso work. First cut a pieceof fabric slightly larger
than the grid; then fastenit to the top, back edge ofthe grid with 1/4-in. sta-ples. Use a razor knife totrim the fabric flush withthe edge of the grid. Thefabric is stiff enough tostay put once you installthe grid against the stops.
Finishing upTo install the surface-mounted hinges, clampadjoining frames together
Make stock by ripping 1/2-in.-sq.strips on the table saw for the stops andscreen grid. Or, if you have a band sawand a planer, rip oversize strips on theband saw, then plane them to 1/2 in.
Whether you use a table saw or a bandsaw, be sure to use a pushstick and
keep your hands away from the blade.Cut the stops to length for the back
of the screen. Drill pilot holes andclearance holes in the stops, and fastenthem to the frame with 1-in. screws(see photo).
Next, cut the strips to size for thegrids and mark the half-lap joint posi-
14 A merican How-To
FRAME AND PANEL CONSTRUCTION
When routing the panel grooves, clamp an
extra piece of stock next to the work to
help stabilize the router.
Before screwing the stops to the frame, bore clearanceand pilot holes, then countersink.
To cut the half-lap joints,
make a sliding table with
runners for both mitergauge slots. Use a stop for
consistent cuts.
Attach the rails and panel to one stile; then add the second stile and clamp. Adjust the
clamps and check that the frame is square.
MAKING GRIDS
Extra stock
Assemble thegrid joints
with glue, tap
them together
lightly if
needed, then
secure with
spring clamps.
Edge guide
Screenstops
Stop
8/8/2019 Folding Room Divider
5/5
with 1/8-in. spacers between them (seephoto). Position the double-actionhinges (see SOURCES) on the frameedges, then mark and drill pilot holes for
the hinge screws (use the screws provid-ed). Check that the hinges work correct-ly, then remove them for finishing.
Sand each frame section with220-grit paper and dust thoroughly. I
applied two coats of satin polyurethanevarnish, but you can use any clear fin-ish. Reinstall the hinges once the finishhas cured.
To complete the divider, drill andcounterbore pilot holes for screws inthe top and bottom faces of each grid.
Lay the divider on a padded table andinstall the grid panels with brass flat-head wood screws.
SOURCES
Abe Schuster Plastics, Oakland, CA
(510) 653-3588
Rockler Woodworking and Hardware,
Medina, MN, (800) 279-4441
www.rockler.com
Club member Neal Barrett is a profession-
al woodworker from Rochester, New York.
September/October 1999 15
1/8-in. spacers
To install the hinges, clamp the frames
with 1/8-in. spacers between them, then
mark and bore the screw holes.
November/December Preview
AmericanHow-ToOFFICIAL PUBLICATION OF THE HANDYMAN CLUB OF AMERICA
Customize Your Closets
Brighten Your Bath
Banish Ice Dams
Build Your Own Sofa
Tune Your Garage Door
Plus: Table Lamp Plans