Post on 23-Jun-2020
Master Level Thesis
European Solar Engineering School
No. 243, June 2018
Experimental Characterisation and Modelling of a Membrane
Distillation Module Coupled to a Flat Plate Solar Collector Field
Master thesis 30 credits, 2018 Solar Energy Engineering
Author: David d’ Souza
Supervisors: Mats Rönnelid, Guillermo Zaragoza
Examiner: Ewa Wäckelgård
Course Code: EG4001
Examination date: 2018-06-08
K
Dalarna University
Solar Energy
Engineering
i
3
Acknowledgement
The author would like to thank the researchers and technical staff at the Plataforma Solar
de Almeria (Spain), for their technical support and guidance, especially Dr. Guillermo Zaragoza
who lent his experience and in-depth knowledge on membrane distillation technology and its
application to advise and assist in the thesis process. The experimental setup and workspace was
provided by the Plataforma Solar de Almeria through Dr. Zaragoza. From Dalarna University,
the author would like to give thanks to Mats Rönnelid who provided ample support and
assistance with this thesis work particularly when the experimentation work was delayed beyond
the initially scheduled timetable and flexibility was required to come up with an improvised
solution and schedule.
The author would like to acknowledge the role of the European Solar Engineering School
(ESES) and Dalarna University for providing a strong technical base, through their Masters
programme, from which to work on this Masters thesis as well as their scientific collaboration
and association with the Plataforma Solar de Almeria which made this thesis work possible in the
first place.
Finally, unreserved thanks to family and friends without whose support, patience, love and
blessings this thesis would not be possible.
4
Contents
1. Introduction ................................................................................................................................ 8
1.1 Theory and Background ................................................................................................... 8
1.1.1 Basic theory of Membrane Distillation................................................................... 8
1.1.2 Basis of classification and configuration ................................................................ 9
1.1.3 Direct Contact Membrane Distillation and Permeate Gap Membrane ................
Distillation ................................................................................................................ 10
1.1.4 Module construction and design ........................................................................... 11
1.1.5 Solar thermal application in MD ........................................................................... 11
1.2 Aim ..................................................................................................................................... 12
1.3 Method .............................................................................................................................. 12
1.3.1 Experimental Setup ................................................................................................. 13
1.3.2 Uncertainties in measurement data ....................................................................... 15
1.4 Previous Work .................................................................................................................. 15
2. Experiment and Calculations.................................................................................................. 17
2.1 Characterisation and Performance Evaluation of PGMD module .......................... 17
2.1.1 Selection of operating variables ............................................................................. 17
2.1.2 Selection of performance indicators ..................................................................... 18
2.1.3 Experiment runs ...................................................................................................... 20
2.1.4 Uncertainty Analysis ................................................................................................ 21
2.1.5 Limitations of current method and comparison with other studies ................ 22
2.2 Mathematical Modelling of overall system ................................................................... 23
2.2.1 Modelling the MD loop .......................................................................................... 28
2.2.2 Limitations of mathematical model ...................................................................... 31
3. Results and Discussion ............................................................................................................ 32
3.1 Characterisation and performance evaluation of PGMD module............................ 32
3.1.1 Variation with feed flow rate (�̇�𝐹) ......................................................................... 33
3.1.2 Variation with evaporator inlet temperature (𝑇𝑒𝑣𝑎𝑝𝑖𝑛) ....................................... 37
3.1.3 Variation with condenser inlet temperature (𝑇𝑐𝑜𝑛𝑑𝑖𝑛) ....................................... 40
3.1.4 Repetition of experiment run ................................................................................. 42
3.1.5 Validation and comparison of experimental results ........................................... 43
3.2 Analysis with Mathematical Model ................................................................................ 45
3.2.1 Validation of mathematical model of solar loop ................................................. 45
3.2.2 Validation of MD module and loop ..................................................................... 46
5
3.2.3 Minimum radiation required for MD operation ................................................. 47
3.2.4 Auxiliary cooling required in solar loop for steady state operation.................. 48
4. Further Discussion ................................................................................................................... 49
4.1 Operation with solar thermal collector field ................................................................ 49
4.1.1 System with Inertia tank ......................................................................................... 49
4.1.2 System with Storage tank ........................................................................................ 50
4.2 Future areas of interest and investigation ..................................................................... 51
5. Conclusions ............................................................................................................................... 52
6. References ................................................................................................................................. 54
7. Appendices ................................................................................................................................ 56
7.1 Appendix A ....................................................................................................................... 56
7.1.1 Technical details of experimental setup and its components ............................ 56
7.1.2 Images/Pictures of experimental setup ................................................................ 57
7.2 Appendix B ....................................................................................................................... 59
7.3 Appendix C ....................................................................................................................... 60
7.4 Appendix D ...................................................................................................................... 61
7.4.1 Derivation of uncertainty/error of performance indicators ............................. 61
7.4.2 Derivation of uncertainty/error of solar collector efficiency............................ 64
7.4.3 Derivation of uncertainty/error of heat required for MD ................................ 66
7.5 Appendix E ....................................................................................................................... 68
7.6 Appendix F ....................................................................................................................... 69
7.6.1 Derivation of Minimum Radiation required for MD operation ....................... 69
7.6.2 Uncertainty in calculated Minimum Radiation for MD operation ................... 71
7.6.3 Derivation of Auxiliary cooling required for steady state operation ................ 72
7.6.4 Uncertainty in calculated Auxiliary Cooling required for steady state ............. 74
6
Abbreviations
Abbreviation Description
DCMD Direct Contact Membrane Distillation
MD Membrane Distillation
PGMD Permeate Gap Membrane Distillation
7
Nomenclature
Symbol Description Unit
𝑇𝑒𝑣𝑎𝑝𝑖𝑛 Evaporator inlet temperature °C
𝑇𝑐𝑜𝑛𝑑𝑖𝑛 Condenser inlet temperature °C
�̇�𝐹 Seawater feed flow rate l/h
𝑆𝑇𝐸𝐶 Specific thermal energy consumption kWh/m3
𝐺𝑂𝑅 Gained output ratio -
𝑃𝑓𝑙𝑢𝑥 Permeate/distillate flux l/(h∙m2)
𝜀 Effectiveness of internal heat exchange -
8
1. Introduction
1.1 Theory and Background
Water scarcity is an increasing issue for a growing global population which is expected to
surpass 8.3 billion people by 2030 [1]. In a 2013 study [2], it was estimated that approximately
700 million people were suffering from water stress and scarcity and this number was expected
to rise up to 2.8 billion by 2025. The global demand for freshwater is predicted to rise over 50 %
by 2050 [1]. Seawater desalination is widely seen as a solution to the depleting freshwater
resources, especially in arid and semi-arid regions, and its online capacity has surged from 7
million m3/day in 2000 [3] to today’s installed capacity of 78.4 million m3/day [4]. However these
desalination plants, about 17 % and 8 % using thermally powered multi-stage flash (MSF) and
multi-effect distillation (MED) technology and 70 % using electrically driven reverse osmosis
(RO) technology, are mostly high capacity, capital and energy intensive plants [3]. Only 3.5 % of
the global desalination capacity comprises of small scale plants (less than 1000 m3/day) [3] which
is what is required in rural areas which, in turn, represent 80 % of the population without access
to fresh drinking water. Moreover, the three desalination technologies mentioned above require
significant amounts of chemicals for smooth operation which poses an additional cost and
logistical hassle in rural areas. Hence there is a growing demand for the development of a small
scale, chemical free and operationally non-complex desalination technology that can be
implemented in rural areas preferably coupled to a renewable energy system.
Membrane distillation (MD) as a desalination method can largely meet the above criteria and its
scalability makes it suitable for a wide range of application vis-à-vis operational capacity. While
the distillation process itself does not rely on any chemical treatment, depending on the
conditions of the inlet feedwater, some pre-treatment might be necessary for a longer operational
life. The easy coupling with renewable energy (notably solar thermal energy) make MD especially
suitable for stand alone and off grid applications [5]–[7].
1.1.1 Basic theory of Membrane Distillation
Membrane distillation (MD) is a water purification method which uses thermal energy to
produce freshwater from otherwise impure water such as seawater, industrial wastewater etc. In
the MD process, heat is applied to a flowing feedwater stream to generate water vapour. This
water vapour then passes through a hydrophobic membrane which doesn’t permit liquid water
molecules to pass through but only volatiles, chiefly water vapour, to penetrate the membrane.
On the other side of the membrane the vapour emerges and eventually forms the
permeate/distillate.
There is always a liquid-vapour interface on the feedwater side of the membrane (at the
membrane pores) as the stream of feedwater is kept in direct contact with the membrane surface.
With the inner membrane pore volume having to remain dry, the driving force behind the mass
transfer of water vapour is the difference in vapour pressures on either side of the membrane.
9
Besides the mass transfer through the membrane volume, there is also an active transmembrane
heat transfer. Ideally the heat transfer would be solely the latent heat of evaporation as the
vapour is generated on the feed side and then released on the permeate side. However, in
practical application, besides the latent heat demand, there is also a sensible heat transfer that
occurs from the hot feedwater side to the cooler permeate side via conduction through the
membrane. As this additional heat transfer doesn’t contribute to the mass transfer of water
vapour, it is considered as an undesirable heat loss.
1.1.2 Basis of classification and configuration
While the vapour pressure at the feed side liquid-
vapour interface is defined, owing to the direct
contact between the feedwater and the surface of the
membrane, the vapour pressure at the permeate side
liquid-vapour interface (and hence the effective
vapour pressure gradient across the membrane) is set
by one of the following general approaches [3]:
- Application of a lower temperature on the
permeate side liquid-vapour interface
- Application of a sweeping gas on the
permeate side of the membrane
- Application of a vacuum on the permeate side
of the membrane
The implementation and application of these
approaches to create a driving force have contributed
in the development of different MD configurations
which in turn provides a simple means of
classification among MD technologies. Variations in
geometric and spatial designs/layouts of the channels
and overall module provide an additional method of
differentiation and classification. The most common
configurations, including the one used in this study,
utilise a temperature gradient to establish the vapour pressure gradient and hence the driving
force.
Figure 1: Principle of Membrane Distillation [5]
10
1.1.3 Direct Contact Membrane Distillation and Permeate Gap Membrane
Distillation
The simplest MD configuration is the direct contact membrane distillation (DCMD) type
which can be seen in Figure 1 [5]. In DCMD the feed water is heated before passing through the
‘evaporator channel’ which is so called as it is from this channel that the water vapour is
generated through evaporation. The water vapour, generated at the liquid-vapour interface in the
evaporator channel, then passes through the membrane before emerging on the permeate side
also referred to as the condenser channel as it is in this channel that condensation occurs. The
driving force in DCMD owes itself to the temperature difference between the hot feedwater in
the evaporator channel and the colder permeate/distillate in the condenser channel.
Alternatively, the condenser channel may be defined as the channel which carries the coolant
that causes condensation. In the case of DCMD, the coolant is the permeate itself. While
DCMD has the advantage of a higher driving force compared to other MD configurations, due
to a lower heat transfer resistance (only the membrane itself) between the feedwater and the
coolant (permeate), there is a high degree of sensible heat loss across the membrane. In other
words, the permeate produced in the condenser channel is unproductively heated up due to
conduction of heat through the membrane from the hotter evaporator channel which,
furthermore, leads to a decrease in the driving force due to a lowering in the temperature
difference in the two channels [3], [8].
An improvement on the DCMD configuration is what is referred to as permeate gap membrane
distillation (PGMD) or liquid gap membrane distillation (LGMD) which can be seen in Figure 2
below [9], [10].
In terms of construction, the main
difference between PGMD and DCMD is
the addition of an impermeable foil/film
(referred to as condenser foil in Figure 2)
after the membrane on the permeate side.
As can be observed from Figure 2, there
are three channels in PGMD as against
two in the case of DCMD. The liquid
permeate is formed between the
membrane and the impermeable film in
what is referred to as the distillate channel.
The coolant, which could be any suitable
cooling fluid, flows in the condenser channel.
Thus the temperature difference, which
creates the driving force, is created by the hot feedwater on one side of the membrane
(evaporator channel) and the coolant in the condenser channel. It should be noted that the
addition of the extra barrier creates an additional heat transfer resistance, in the case of PGMD,
reduces the effective temperature gradient and hence it can never achieve the same driving force
and flux as compared to a comparable DCMD system [3].
However the main advantage of PGMD lies in that it separates the permeate from the coolant
and hence allows for any fluid to be used as the cooling fluid. This provides the opportunity of
using the cold inlet feedwater (before it is heated externally) to be used as a coolant and hence
Figure 2: Permeate Gap Membrane Distillation [9][10]
11
enables sensible heat recovery. Hence the heat transferred across the membrane, which would
have been lost as sensible heat to the permeate in the case of DCMD, can be partly recovered as
sensible heat to the inlet feedwater. While this sensible heat recovery in the condenser channel
reduces the external heat required to reach a desired temperature in the evaporator channel, the
driving force is reduced (due to a reduction in the temperature gradient) as the temperature in
the condenser channel increases.
Thus, with respect to the desired extent of internal sensible heat recovery from an overall
systems perspective, a compromise must be made between the reduction of heat required to
operate the MD system and the rate of distillate production.
1.1.4 Module construction and design
The membrane used in this study was of the spiral
wound design which allows for a compact arrangement
besides effective internal heat recovery [9]. Internal heat
recovery is the heat gained by the cool feedwater in the
condenser channel. The construction and layout of a spiral
wound membrane with PGMD is as shown in Figure 3
[9].
1.1.5 Solar thermal application in MD
As mentioned earlier, an external heat supply is needed to drive the MD process. The
application of solar thermal collectors to this end is an especially promising area of interest and
several experimental studies have been done in solar thermal membrane distillation [5]–[8], [11],
[12] for the following reasons. Firstly, arid and semi-arid regions with water scarcity tend to also
have good solar irradiation i.e are largely in the ‘solar belt’ and hence there is a positive
correlation between water necessity and solar energy available. Normal operating temperatures
for MD (in the evaporator channel) are between 60°C and 85°C [8] which is well within the
working range of flat plate thermal collectors. Moreover, intermittency in heat supplied, which is
highly probable in solar thermal generation, can be tolerated in the MD process as it can sustain
fluctuations in external heat flux without damage or necessitating complex control systems.
Figure 3: Schematic of the spiral wound module concept: (1)
condenser inlet, (2) condenser outlet, (3) evaporator inlet, (4) evaporator
outlet, (5) distillate outlet, (6) condenser channel, (7) evaporator
channel, (8) condenser foil, (9) distillate channel and (10) hydrophobic
membrane [9]
12
1.2 Aim
• Undertake a characterisation and performance evaluation of a pre-commercial spiral
wound permeate gap membrane distillation unit at various operating conditions
• Develop a simplified mathematical model of the solar thermal membrane distillation
system
• Develop general guidelines on how best to operate a solar thermal membrane distillation
system with an inertial tank and a storage tank
1.3 Method
The characterisation of the PGMD module was carried out using the experimental setup
described in detail below. The experiment work and analysis, to the end of the above-mentioned
aims, was carried out at the Plataforma Solar de Almeria (PSA) in Spain. For the design of
experiments (DoE), the one-variable at a time method was employed where successive
experiments are run with one operating variable (may also be referred to as operating parameter
or condition) changed leaving the others constant. In this way, the experiment matrix consists of
all combinations of values of operating variables, within their respective ranges. The operating
variables to be varied, the range within which they’re varied, their levels within the selected range
and the performance parameters to be evaluated were first chosen before the experiment runs
were initiated.
In parallel with the characterisation and performance evaluation of the PGMD module, it was
also desired to investigate methods of optimum integration and operation of the same with a
solar thermal collector system. To this end, a simple mathematical model was developed and,
after addition of the technical data from the components of the experiment setup to the model,
it was validated using field data. After validation, the model can be used to predict and guide
toward the best means of solar integration and potential methods to achieve a steady state
operation of the overall system.
Thermophysical properties of the fluids used in this work were determined using validated
models and equations from earlier studies. Specifically, propylene glycol (used in the solar loop)
from [13], pressurised water (used in the tank loop) from [14] and seawater at 3.5 % salinity (in
the MD loop) from [15]. These loops will be investigated more closely in the following section.
The thermophysical properties relating to water-water vapour phase change (specifically the
latent heat of vaporisation) were calculated using equations from [16].
13
1.3.1 Experimental Setup
The experimental setup that was utilised for this study is located at the Plataforma Solar de
Almeria (PSA) in Spain. The overall system can be considered as consisting of three interacting
circuits/loops. The solar loop (Figure 4) consists of the solar collector field whose output is fed
to a heat exchanger which transfers the solar heat from the solar loop to the tank loop (Figure 5).
In other words, this heat exchanger (henceforth referred to as HX1) is used to charge the tank
using solar heat. The solar collector field consists of 4 fixed flat plate collector modules, named
LBM 10 collectors and manufactured by Wagner and Co, connected in series with a total
aperture area of 40.4 m2. The working fluid in the solar loop is propylene glycol with a
concentration of approximately 5 %. The air cooler in the solar loop serves to regulate the
temperature of the fluid entering HX1. To achieve steady state operating conditions, the air
cooler plays an important role in preventing the fluid from rising to a higher temperature than
required which may occur in case of excessive incident solar irradiation.
Figure 5: Hydraulic layout of Tank loop of experimental setup
Figure 4: Hydraulic layout of Solar loop of experimental setup
14
The tank, in turn, discharges itself to the heat load of the MD unit via the heat exchanger
(henceforth referred to as HX2) that connects the tank loop to the MD loop (Figure 6). The tank
loop uses water (at 2 bar) as its working fluid.
Figure 6: Hydraulic layout of MD loop of experimental setup
From these three figures it can be observed how the solar heat is utilised to drive the MD
process. While carrying out the experiments it was imperative to maintain the operating
parameters at a nearly constant level else the results might have been affected. Chief among these
operating parameters were the temperatures at the inlet of the heat exchanger HX2 (from the
tank side) and at the inlet of the condenser channel. The tank side heat exchanger inlet
temperature was maintained by a combination of two effects. Firstly, a large volume, 1.5 m3, of
the tank (which acted as an inertial tank during the experiments) absorbed the fluctuations in
solar heat output to provide a near steady outlet temperature from its upper node. Secondly the
flow diverter (or tempering valve) provided a faster means of regulation of the temperature to
HX2 by appropriate mixture with the return flow from the same heat exchanger.
During the course of the MD operation, as can be seen from Figure 6, the brine from the outlet
of the evaporator channel returned back to the seawater tank. This led to an increase in the
seawater tank’s temperature as the evaporator outlet temperature is always higher than the
condenser inlet’s (due to the non-ideal effectiveness of the internal heat recovery process). To
offset this temperature gain and ensure that the condenser inlet temperature remained constant,
the seawater tank needed to be actively cooled.
Technical details about the solar collector field and other important components, along with
some on-site pictures of the same, can be found in Appendix A.
15
1.3.2 Uncertainties in measurement data
Most of the uncertainties that could affect the final evaluated performance/result lie in the
MD loop (see Figure 6). The weighing scale, that measures the final and initial weight of the
distillate produced, relied on the uniform weight of the force being applied on it. However, in
windy ambient conditions, the tube from the distillate channel to the tank shifted slightly and the
final distillate container itself rocked slightly when the wind was violent enough and this was a
source of random error in the measurement. Moreover, as was discussed above, the evaporator
outlet i.e the concentrated feedwater was returned to the seawater tank while the distillate was
collected separately and only returned to the tank after the completion of the experiment. Hence
the salinity of the seawater increased continuously over the course of the experiment. However,
this is not expected to be a major source of error as the seawater tank was of a large capacity and
the separation of 40-45 kg of freshwater (approximately the maximum amount of distillate
produced during an experiment run from system start up through steady state conditions) from
it should not drastically affect the salinity of the tank. Moreover the MD process is not severely
affected by minor changes in the salinity of the inlet seawater [7], [9] which is estimated to
increase by approximately 15%.
1.4 Previous Work
In this chapter, the current study will be contextualised with an overview of the previous
work that has been done in the field of membrane distillation, particularly spiral wound and
permeate gap types, and solar thermal energy systems. As experimental work was a major part of
this study, many previous experimental analyses on spiral wound PGMD systems have been
reviewed [5], [8]–[10]. In [5] eight completely solar powered spiral wound PGMD systems are
developed with daily distillate capacities from 60-150 litre are designed and implemented in five
different countries. Solar thermal energy was used to drive the MD process while auxiliary
electrical loads (such as from pumps and valve operation) were powered by solar photovoltaics.
A major aim of [5] was the implementation of long term, low maintenance and independently
operational distillation systems in remote areas.
A theoretical analysis of the performance enhancements achieved after the deaeration of
membrane pores using feedwater deaeration was carried out in [10] to confirm the understanding
that this leads to a decrease in the molecular diffusion (mass) resistance and hence an increase in
the distillate flux. A comprehensive experimental campaign was carried out to test this in practice
using both aerated and deaerated feedwater on a spiral wound permeate gap membrane
distillation unit. Moreover, several operational parameters such as pressures, feed flow rates, feed
water salinities and temperature levels were varied in [10] to quantify their effects on the
deaerated system. Production and characterisation of spiral wound permeate gap membrane
distillation units (with total membrane areas of 5 m2, 10 m2 and 14 m2) were carried out in [9].
Module operating points were controlled by the automated experimental test rig which utilised
an electrical heater as a heat source. The operating variables in [9] included the condenser inlet
temperature, evaporator inlet temperature, feed flow rate and feed water salinity. Mathematical
equations and models were used to analyse and discuss in depth the results and system
behaviour.
16
Response surface methodology was used in [8] to mathematically (statistically) model and
describe the permeate flux and the specific thermal energy consumption and subsequently
perform a dual optimisation of the same two parameters. Detailed, statistically determined design
of experiment and optimisation study of a spiral wound permeate gap membrane distillation
system was performed besides a validation of the RSM model using further experimentation.
These previous experimental works were especially relevant to the current work as they all
utilised spiral wound PGMD modules and hence their experiment results can be validly
compared with the results from this study vis-à-vis values of performance indicators, behaviour
at different operating conditions etc. Additionally the details and discussions regarding the design
of experiments, experiment setup, methodology, methods used and their respective limitations,
practical experiences etc are all applicable to the current work and hence were reviewed carefully.
In fact the experimental test rig used in [8] was the same as the one used in this study.
For the analysis of the flat plate solar collector field, [17] was used which can be summarised as
an in-depth look at solar thermal systems and designs including detailed individual component
description, reviews and models, system integration and related considerations. While [17]
provides a comprehensive study of different types of solar thermal systems (including
concentrating types), it was used exclusively for its analysis of flat plate collector systems and
tanks besides some basic formulae for solar angles, incidence angle modifiers etc. The analysis of
the solar field with regards to system evaluation and strategies to achieve steady state operation
were largely guided by this work.
Besides the experiment work with the MD module, for a more descriptive and complete analysis
[3] was referred to. It is a dissertation providing a comprehensive review of membrane
distillation technology and its physical and mathematical modelling besides detailing methods
and areas of optimisation and experimentation. An uncertainty analysis in process (between
different module types) and module experimentation is also carried out. The study was aimed
towards a broader thermodynamic analysis of membrane distillation to provide a model-based
method for analysis and considers otherwise neglected aspects such as electrical load and
economic analysis. This work was used to analyse in more depth the behaviour of the membrane
distillation unit as well as provide direction when it came to design of experiments and
determination of errors (error analysis).
With regards to the mathematical model used, a simplified method of describing the PGMD
module was desired. [18] provided a method to model balanced single pass/stage MD systems
(including DCMD and PGMD systems) which was used, in part, in this work. The model in [18]
centred around treating the MD module as a counterflow/counter current heat exchanger. For
PGMD modules, a relation was derived for the gross output ratio (GOR) and the MD thermal
efficiency in terms of the effectiveness of heat exchange and the number of transfer units
(NTU). The model was validated against a more detailed discretised computational model and
found deviations in GOR and flux below 11 %. In the development of the simplified
mathematical model in this study, the same concept of heat exchanger effectiveness was used
and some of the formulation associated with the same was also utilised in this work.
17
2. Experiment and Calculations
This chapter will subsequently be divided into two sections, one describing the
characterisation and performance evaluation of the spiral wound PGMD module and the second
part will look into the development of a mathematical model for the solar loop and extend the
same principles to the other loops to produce a simplified model of the overall system.
2.1 Characterisation and Performance Evaluation of PGMD module
Before conducting any characterisation and/or performance evaluation, it is imperative to
first and foremost identify the experimental inputs (or operating variables) to adjust, the ranges
within which they should be adjusted and the specific levels or values that they should be held at
during the experiment run. After this is done the final process outputs/results must be selected
as performance indicators for analysis of the operational behaviour and performance of the
PGMD module. The design of experiments (DoE) is explained in the following sections.
2.1.1 Selection of operating variables
Based on previous experimental work on spiral wound PGMD modules [8]–[10] as well as
physical limitations of the module based on the manufacturer’s specifications, the chosen
operating variables to vary were the evaporator inlet temperature (𝑇𝑒𝑣𝑎𝑝𝑖𝑛), the condenser inlet
temperature (𝑇𝑐𝑜𝑛𝑑𝑖𝑛) and the seawater feed flowrate (�̇�𝐹). The ranges and levels of these
variables can be seen in Table 1 below.
Table 1: Operating variables with experimental range and levels
Operating variable Range Levels
𝑇𝑒𝑣𝑎𝑝𝑖𝑛 (°C) 60 – 80 60, 70, 80
𝑇𝑐𝑜𝑛𝑑𝑖𝑛 (°C) 20 – 30 20, 25, 30
�̇�𝐹 (l/h) 200 – 400 200, 300, 400
During an experiment run it is essential to keep the operating variables stable however it is near
impossible to maintain them at exactly constant values. A tolerance of 2 °C was set for the
𝑇𝑒𝑣𝑎𝑝𝑖𝑛 and 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 (the actual achieved experimental dispersions were much lower) and while
no tolerance was formally defined for �̇�𝐹 it was aimed to reduce its dispersion to the maximum
extent. The experimentally achieved mean values of the operating variables, along with their
maximum and minimum values and standard deviations (for all the experimental runs) can be
found in Appendix B.
18
It was initially desired to use a higher feed flowrate (500 l/h) and while it was possible to conduct
some experiment runs at this higher flowrate, within the bounds of the above mentioned
maximum allowed dispersion in operating variables (especially 𝑇𝑐𝑜𝑛𝑑𝑖𝑛), it was impossible to
carry out the entire set of experiment runs at �̇�𝐹 = 500𝑙
ℎ simply because of limitations in the
experimental setup. Namely that the cooling capacity of the compression chillers for the seawater
tank were insufficient to maintain a near-constant 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 ; instead there was a gradual rise in its
value until it exceeded the experimental tolerances defined earlier.
2.1.2 Selection of performance indicators
Performance indicators in thermal distillation processes are well defined, generally
unchanged across distillation technologies and ubiquitous in experimental works [6], [9], [10],
[19] and the following have been selected in this study;
1. Permeate flux or 𝑷𝒇𝒍𝒖𝒙 [l/(h∙m2)] : The rate of permeate production per unit area of
the membrane. As it is area-specific, the 𝑃𝑓𝑙𝑢𝑥 provides a simple means of comparison
between MD modules of different sizes and construction. Note that it is the total
membrane area which is used in these calculations. It is given by [3];
𝑃𝑓𝑙𝑢𝑥 =�̇�𝑝
𝐴𝑀
Equation 1
Where �̇�𝑝 is the volumetric rate of permeate production [l/h],
𝐴𝑀 is the total membrane area [m2]
This can be alternatively written, in terms of actual measured variables, as;
𝑃𝑓𝑙𝑢𝑥 =�̇�𝑝
𝜌𝑝 ⋅ 𝐴𝑀
Equation 2
Where �̇�𝑝 is the mass flow rate of permeate production [kg/h],
𝜌𝑝 is the density of the permeate [14] at mean condenser temperature [kg/l]
2. Specific thermal energy consumption or 𝑺𝑻𝑬𝑪 [kWh/m3] : The heat energy
required to produce a unit volume of permeate. This performance indicator is common
among all thermal distillation technologies and is the one of the most widely used
benchmarks of thermal performance.
𝑆𝑇𝐸𝐶 =𝑄𝐻𝑋2𝑉𝑝
Equation 3
19
Where 𝑄𝐻𝑋2 is the total energy input required for the distillation process [kWh],
𝑉𝑝 is the total volume of permeate production [m3]
The STEC may also be represented in per unit time quantities (for example power instead
of energy). As the experiments are run in steady state conditions, by definition, the quantities are
stable over time and hence there is no difference in the STEC when integrating over time. Hence
the STEC can be expanded and rewritten, in terms of actual measured variables, as;
𝑆𝑇𝐸𝐶 =�̇�𝐹 ⋅ 𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ 𝜌𝑝 ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡)
�̇�𝑃 Equation 4
Where �̇�𝐹 is the volumetric flow rate of the feedwater [l/s]
𝜌𝐹 is the density of the feedwater [15] at mean cold-side HX2 temperature [kg/l]
𝐶𝑝𝐹 is the isobaric specific heat capacity [15] of the feedwater at mean cold-side
HX2 temperature [kJ/(kg ∙°C)]
𝜌𝑝 is the density of the permeate [14] at mean condenser temperature [kg/m3]
𝑇𝑒𝑣𝑎𝑝𝑖𝑛 is the evaporator inlet temperature [°C]
𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡 is the condenser outlet temperature [°C]
3. Gained Output Ratio or 𝐺𝑂𝑅 [ - ] : Analogous to 𝑆𝑇𝐸𝐶, the 𝐺𝑂𝑅 can be defined as the
ratio of the heat required to vaporise the permeate and the actual heat supplied. It is also
a widely used performance indicator and can be expressed as;
𝐺𝑂𝑅 =𝑚𝑝 ⋅ 𝛥ℎ𝑣
𝑄𝐻𝑋2 Equation 5
Where 𝑚𝑝 is the total mass of permeate production [kg]
𝛥ℎ𝑣 is the normalised latent heat of vaporisation of water [16] at mean
evaporator temperature [kJ/kg]
Similar to the STEC, the GOR may be rewritten in terms of per unit time quantities and
may hence be alternately expressed as;
𝐺𝑂𝑅 =�̇�𝑝 ⋅ 𝛥ℎ𝑣
�̇�𝐹 ⋅ 𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡) Equation 6
20
In addition to these three performance indicators, a fourth parameter is defined to
determine the extent of sensible heat exchange, within the MD module, at different operating
conditions. While this is not directly a measure of the performance of the MD process, it
provides insight into the relative operating dynamics at various operational points. This
parameter is the effectiveness of the internal heat exchange (between the evaporator and the
condenser channels) and is the ratio of the actual heat exchange to the maximum theoretically
possible and is given by [17], [18], [20];
𝜀 =𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛
Equation 7
Where 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 is the condenser inlet temperature [°C]
2.1.3 Experiment runs
From the Table 1, it can be inferred that, given that there are three experimental inputs
(operating variables) and each having three experimental levels, the total number of experiment
runs required for a full characterisation is 27. Experiment runs were of 45 minutes barring the
first three runs which were of 60 minutes. Two repetitions of a randomly selected experimental
run were also performed, on different days, to observe the variability in the performance
indicators over different experiment runs.
In a normal operation, after a stationary state is achieved (i.e the variables remain stable in value
over a period of time) the system is allowed to run for at least an hour before measurements are
recorded and the experiment run formally begins. This is to ensure that the MD unit has
achieved steady state operation. Over one working day there are no more than 2 experiment runs
conducted and between each run at least 2.5 hours are provided to ensure that the second run is
not affected by the first.
There are several factors/influences, which are largely uncontrolled, that require time to settle
into a steady state of operation. The most significant of these being the thermal and
hydrodynamic boundary layers that form on either exposed side of the membrane surface i.e on
the membrane surface in the evaporator channel and distillate channel. Establishing and
stabilisation of these boundary layers requires time. A similar consideration must be made for the
heat transfer surfaces of the heat exchanger between the tank loop and MD loop. Lastly the
thermal capacitance of the MD module, besides the heat exchanger, must also be considered as a
contributor to potential unsteadiness in experiment operation. It is for these reasons that the
MD module was first operated under stationary state conditions for some period of time before
any measurements are made.
The date and time of the experiment runs can be found in Appendix C.
21
2.1.4 Uncertainty Analysis
An uncertainty analysis was carried out to determine the uncertainty error in the final
results/parameters. Such an analysis is crucial, especially in experimental work, to quantify the
inaccuracies and validity of experimentally determined outputs.
It is first necessary to calculate the error in measured variables such as temperatures from
temperature sensors, volumetric flow rates from flow meters etc. In this study, measured variable
errors were divided into experimental errors, instrumental/calibration errors and random errors.
The total error of a measured variable (∆𝑧) was calculated as the root mean square of its
experimental, instrumental and random error as [3];
∆𝑧 = √𝜎𝑒𝑥𝑝2 + 𝜎𝑐𝑎𝑙2 + 𝜎𝑟𝑎𝑛𝑑𝑜𝑚
2 Equation 8
Where ∆𝑧 is the total error of the measured variable
𝜎𝑒𝑥𝑝 is the experimental error of the measured variable
𝜎𝑐𝑎𝑙 is the instrumental/calibration error of the measured variable
𝜎𝑟𝑎𝑛𝑑𝑜𝑚 is the random error of the measured variable
Experimental error is the error that arises due to the dispersion/variation of the measured
variable during the experiment run. One standard deviation from the mean value was taken as
the experimental error. Of course this error can be minimised by careful operation of the system
during the experiment to reduce dispersion and operate within experimental boundary
conditions earlier defined (see Chapter 2.1.1). The mean, maximum and minimum values, as well
as the standard deviation, of the three main operating variables (𝑇𝑐𝑜𝑛𝑑𝑖𝑛 , 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 and �̇�𝐹) for
each experiment run, can be found in Appendix B.
Instrumentation/calibration error arises due to inaccuracies in the measuring device itself and is
a physical limitation of the device which cannot be altered/minimised.
Random error is one which quantifies the disruptive effect of a largely uncontrollable
environmental factor, such as wind, humidity, cloud cover etc on the measured variable. The
magnitude of this error is a rough approximate based on real-time observed random variability in
the measured values. This has been briefly discussed in an earlier section (see Uncertainties in
measurement data).
The final output parameter, whose uncertainty is to be determined, is a function of some
measured and derived variables. As it is a multivariate function, it’s error must account for the
individual errors of each independent variable. To this effect, the Gaussian law of error
propagation [3] is applied to give a probable error for a complex function 𝑓 with 𝑛 independent
variables as;
22
∆𝑓( 𝑧𝑖𝑖=1𝑛 ) = √∑(
𝜕𝑓(𝑧𝑖)
𝜕𝑧𝑖∆𝑧𝑖)
2𝑛
𝑖=1
Equation 9
The evaluation of the measured and final parameter errors was carried out for each experiment
run using the above equations (Equation 8 and Equation 9). The derivation of the final
uncertainty/error equation for each output variable (𝑃𝑓𝑙𝑢𝑥, 𝑆𝑇𝐸𝐶, 𝐺𝑂𝑅 and 𝜀) using Equation 9
and substituting the functions from Equation 2, Equation 4, Equation 6 and Equation 7
respectively is shown in Appendix D.
2.1.5 Limitations of current method and comparison with other studies
This study utilised the conventional experimental method or one-variable at a time system where
one operating variable is changed while the others are held fixed. Although this results in a
simplified design of experiments (DoE), the conventional method necessitates a large number of
experiment runs and hence more time for experimentation. Moreover, interactions between the
input operating variables, and their implications on the result/performance, are ignored. An
alternative to the conventional method is the statistically driven experimental model called
Response Surface Methodology (RSM) which was used in [8] to model a spiral wound PGMD
module. Using this method, the number of experiment runs required reduced from 27 using
conventional methods (as is required in this study) to 16. The main drawback of this method is
the complexity related to statistical analysis, such as choice of model order (first-order, second-
order etc), mathematical model used, design of experiments (DoE), multivariate regression
analyses etc.
Electrical consumption as a performance parameter is often overlooked in studies of MD
modules despite it being essential for MD operation [3]. In PGMD modules, the only electrical
load is the feed water pump and since it is far lower in magnitude than the thermal load it has
been neglected in most studies on PGMD modules including in this study. The electrical
consumption rises sharply when feedwater deaeration is used [10] due to the additional use of a
vacuum pump. However without an operating feedwater pump, MD operation would not be
possible and hence the non-inclusion of electrical consumption, irrespective of its magnitude,
should be considered as a limitation. Studies on stand-alone MD systems [5]–[7], for example,
have had to consider this electrical load when sizing the photovoltaic (PV) arrays to meet the
system’s electrical demand.
The variation of performance with salinity was not carried out in this study. Additionally, the
PGMD module could not be tested over its entire working range of operating conditions, as
defined by the manufacturer (Appendix A). The maximum permissible feed flow rate (�̇�𝐹) of the
module was 700 l/h but, as explained earlier (see Chapter 2.1.1), the experimental setup was
inadequate to test the module at flow rates above 500 l/h.
Lastly, due to time constraints, the experiment runs could not be repeated sufficiently to cross-
check the stability and validity of experiment results over different runs. Repetition would have
reduced the experimental error significantly and hence provided more accurate results.
23
2.2 Mathematical Modelling of overall system
The creation of a simple mathematical model using standard and empirical formulae has
been performed in a similar setting [19] i.e with a solar flat plate collector field coupled to a
desalination process system. Starting with the solar field (see Figure 4 and Appendix A), the
thermal efficiency of the solar flat plate collector (𝜂𝑠𝑜𝑙𝑎𝑟) is given by [17], [21];
𝜂𝑠𝑜𝑙𝑎𝑟 = 𝜂0 ⋅ 𝐾𝜏𝛼 −𝑘1𝐺𝑇
(𝑇𝑐𝑜𝑙 − 𝑇𝑎𝑚𝑏) −𝑘2𝐺𝑇
(𝑇𝑐𝑜𝑙 − 𝑇𝑎𝑚𝑏)2 Equation 10
Where 𝜂0 is the zero-loss efficiency or optical efficiency [%]
𝐾𝜏𝛼 is the incidence angle modifier (IAM) [ - ]
𝑘1 is the heat loss coefficient [W/(m2∙K)]
𝑘2 is the temperature coefficient of the heat loss coefficient [W/(m2∙K2)]
𝐺𝑇 is the global/total irradiance on a titled plane [W/m2]
𝑇𝑐𝑜𝑙 is the average temperature of the flat plate solar collector field [°C]
𝑇𝑎𝑚𝑏 is the ambient/environment temperature [°C]
It should be noted that 𝑘1 and 𝑘2 are solar collector parameters and are constant for a given flat
plate collector (see Appendix A). The incidence angle modifier (𝐾𝜏𝛼) is a multiplier that
addresses the effect of the incidence angle (as a deviation from normal incidence) on the
collector plane. It is a function of the incidence angle and is given by [17];
𝐾𝜏𝛼 = 1 − 𝑏0 (1
𝑐𝑜𝑠 𝜃− 1) Equation 11
Where 𝑏0 is the incidence angle modifier coefficient which is a constant for a particular collector
𝜃 is the incidence angle (the angle between the beam radiation and the surface normal)
A description of the calculation of angle of incidence is not shown in this work as it requires
many intermediary calculation steps and, more importantly, is a small and less relevant part of
the overall model. However it has been calculated using standard formulae [17, Ch. 1] in a
worksheet and MATLAB environment.
24
The thermal efficiency may also be written as [17];
𝜂𝑠𝑜𝑙𝑎𝑟 = �̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐶𝑝𝑐𝑜𝑙 ⋅ (𝑇𝑠𝑜𝑙𝑎𝑟𝑜𝑢𝑡 − 𝑇𝑠𝑜𝑙𝑎𝑟𝑖𝑛)
𝐴𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐺𝑇 Equation 12
Where �̇�𝑠𝑜𝑙𝑎𝑟 is the mass flow rate in the solar collector field [kg/s]
𝐶𝑝𝑐𝑜𝑙 is the isobaric specific heat capacity of propylene glycol [13] at average
collector temperature 𝑇𝑐𝑜𝑙 [J/(kg.°C)]
T𝑠𝑜𝑙𝑎𝑟out is the solar collector field outlet temperature [°C]
𝑇solar𝑖𝑛 is the solar collector field inlet temperature [°C]
𝐴𝑠𝑜𝑙𝑎𝑟 is the total aperture area of the solar collector field [m2]
To describe the heat transfer across the heat exchanger between the solar and tank loops (HX1)
the following equation is used [20];
𝑄𝐻𝑋1 = 𝑈𝐴𝐻𝑋1 (𝑇𝐻𝑋1𝑖𝑛𝑠𝑜𝑙𝑎𝑟 − 𝑇𝐻𝑋1𝑜𝑢𝑡𝑡𝑎𝑛𝑘) − (𝑇𝐻𝑋1𝑜𝑢𝑡𝑠𝑜𝑙𝑎𝑟 − 𝑇𝐻𝑋1𝑖𝑛𝑡𝑎𝑛𝑘)
ln(𝑇𝐻𝑋1𝑖𝑛𝑠𝑜𝑙𝑎𝑟 − 𝑇𝐻𝑋1𝑜𝑢𝑡𝑡𝑎𝑛𝑘)
(𝑇𝐻𝑋1𝑜𝑢𝑡𝑠𝑜𝑙𝑎𝑟 − 𝑇𝐻𝑋1𝑖𝑛𝑡𝑎𝑛𝑘)
Equation 13
Where 𝑈𝐴𝐻𝑋1 is the overall heat transfer coefficient of HX1 [W/°C]
𝑇𝐻𝑋1𝑖𝑛𝑠𝑜𝑙𝑎𝑟 is the temperature at the inlet of HX1 on the solar loop side [°C]
𝑇𝐻𝑋1𝑜𝑢𝑡𝑠𝑜𝑙𝑎𝑟 is the temperature at the outlet of HX1 on the solar loop side [°C]
𝑇𝐻𝑋1𝑖𝑛𝑡𝑎𝑛𝑘 is the temperature at the inlet of HX1 on the tank loop side [°C]
𝑇𝐻𝑋1𝑜𝑢𝑡𝑡𝑎𝑛𝑘 is the temperature at the outlet of HX1 on the tank loop side [°C]
The heat transfer may also be written in terms of the sensible heat gained/lost by the fluids on
either side of the heat exchanger as [17], [20];
𝑄𝐻𝑋1 = �̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐶𝑝𝐻𝑋1𝑠𝑜𝑙𝑎𝑟 ⋅ (𝑇𝐻𝑋1𝑖𝑛𝑠𝑜𝑙𝑎𝑟 − 𝑇𝐻𝑋1𝑜𝑢𝑡𝑠𝑜𝑙𝑎𝑟)
= �̇�𝑡𝑎𝑛𝑘𝐻𝑋1 ⋅ 𝐶𝑝𝐻𝑋1𝑡𝑎𝑛𝑘 ⋅ (𝑇𝐻𝑋1𝑜𝑢𝑡𝑡𝑎𝑛𝑘 − 𝑇𝐻𝑋1𝑖𝑛𝑡𝑎𝑛𝑘) Equation 14
Where �̇�𝑡𝑎𝑛𝑘𝐻𝑋1 is the mass flow rate in the HX1 on the cold/tank side [kg/s]
𝐶𝑝𝐻𝑋1𝑠𝑜𝑙𝑎𝑟 is the isobaric specific heat capacity of propylene glycol [13] at mean hot-side
HX1 temperature [J/(kg∙°C)]
25
𝐶𝑝𝐻𝑋1𝑡𝑎𝑛𝑘 is the isobaric specific heat capacity of water (at 2 bar) [14] at mean cold-side
HX1 temperature [J/(kg∙°C)]
The second heat exchanger HX2, between the tank loop and the MD loop (see Figure 5 and
Figure 6), can also be modelled in a similar way with the heat transfer across HX2 given by [20];
𝑄𝐻𝑋2 = 𝑈𝐴𝐻𝑋2 (𝑇𝐻𝑋2𝑖𝑛𝑡𝑎𝑛𝑘 − 𝑇𝑒𝑣𝑎𝑝𝑖𝑛) − (𝑇𝐻𝑋2𝑜𝑢𝑡𝑡𝑎𝑛𝑘 − 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡)
ln(𝑇𝐻𝑋2𝑖𝑛𝑡𝑎𝑛𝑘 − 𝑇𝑒𝑣𝑎𝑝𝑖𝑛)
(𝑇𝐻𝑋2𝑜𝑢𝑡𝑡𝑎𝑛𝑘 − 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡)
Equation 15
Where 𝑈𝐴𝐻𝑋2 is the overall heat transfer coefficient of HX2 [W/°C]
𝑇𝐻𝑋2𝑖𝑛𝑡𝑎𝑛𝑘 is the temperature at the inlet of HX2 on the tank loop side [°C]
𝑇𝐻𝑋2𝑜𝑢𝑡𝑡𝑎𝑛𝑘 is the temperature at the outlet of HX2 on the tank loop side [°C]
In terms of the sensible heat gained/lost by the fluids on either side of the heat exchanger [17],
[20];
𝑄𝐻𝑋2 = �̇�𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡)
= �̇�𝑡𝑎𝑛𝑘𝐻𝑋2 ⋅ 𝐶𝑝𝐻𝑋2𝑡𝑎𝑛𝑘 ⋅ (𝑇𝐻𝑋2𝑜𝑢𝑡𝑡𝑎𝑛𝑘 − 𝑇𝐻𝑋2𝑖𝑛𝑡𝑎𝑛𝑘) Equation 16
Where �̇�𝐹 is the mass flow rate in the HX2 on the cold/MD side [kg/s]
�̇�𝑡𝑎𝑛𝑘𝐻𝑋2 is the mass flow rate in the HX2 on the hot/tank side [kg/s]
𝐶𝑝𝐻𝑋2𝑡𝑎𝑛𝑘 is the isobaric specific heat capacity of water (at 2 bar) [14] at mean hot-side
HX2 temperature [J/(kg∙°C)]
From Equation 7 and Equation 16, 𝑄𝐻𝑋2 may also be expressed in terms of effectiveness of
internal heat recovery 𝜀 [18] as;
𝑄𝐻𝑋2 = �̇�𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (1 − 𝜀) ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛) Equation 17
The overall heat transfer coefficient of a heat exchanger (𝑈𝐴𝐻𝑋), as given in Equation 13 and
Equation 15, is normally determined by the heat exchanger’s physical design/construction which
includes the surface area, thickness, length, surface conditions etc of the heat exchange
material(s) as well as the flow regime, bulk temperature and thermophysical properties of both
fluids besides the unavoidable heat losses that occur during the heat exchange process. A
comprehensive modelling of HX1 and HX2, to reflect the variations in the 𝑈𝐴𝐻𝑋 value that
occur at different operating conditions was beyond the scope of this study and instead Equation
26
14 and Equation 16 will be relied on more heavily to evaluate the heat exchange in HX1 and
HX2 respectively.
To enumerate the variations in the 𝑈𝐴𝐻𝑋 value at different operating conditions, the same was
evaluated for HX2 during the entire experiment campaign. Over the course of all the
experimental runs, it was found that;
𝑈𝐴̅̅ ̅̅ 𝐻𝑋2 = 179.3 𝑊
°𝐶
𝜎𝑈𝐴𝐻𝑋2 = 70.4 𝑊
°𝐶
Where 𝑈𝐴̅̅ ̅̅ 𝐻𝑋2 is the mean overall heat transfer coefficient in HX2 [W/°C]
𝜎𝑈𝐴𝐻𝑋2 is the standard deviation of 𝑈𝐴𝐻𝑋2 [W/°C]
As can be observed above, a single standard deviation makes up almost 40 % of the mean value
which therefore makes the same not a reliable parameter to use in a mathematical model as a
constant value. The exact 𝑈𝐴𝐻𝑋2 values for each experiment run can be found in Appendix E.
Heat losses must also be considered and are most significant in the solar field as it holds the
longest piping (at over 40m). To model this heat loss to the ambient the 𝑈𝐴 value of the pipes is
estimated by first determining the heat losses by the fluid, from the point of exiting the solar
collectors and the point of entry into the heat exchanger HX1, and equating that to the heat loss
through the pipes. The heat lost by the fluid is given by [17], [20];
𝑄𝑙𝑜𝑠𝑠 = �̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐶𝑝𝑆𝐹 ⋅ (𝑇𝑠𝑜𝑙𝑎𝑟𝑜𝑢𝑡 − 𝑇𝐻𝑋1𝑖𝑛𝑠𝑜𝑙𝑎𝑟) Equation 18
The same heat is lost through the pipes and can be expressed as [20];
𝑄𝑙𝑜𝑠𝑠 = 𝑈𝐴𝑝𝑖𝑝𝑒 ⋅ (𝑇𝑠𝑜𝑙𝑎𝑟𝑜𝑢𝑡 + 𝑇𝐻𝑋1𝑖𝑛𝑠𝑜𝑙𝑎𝑟
2− 𝑇𝑎𝑚𝑏) Equation 19
Where 𝐶𝑝𝑆𝐹 is the isobaric specific heat capacity of propylene glycol [13] at mean
field pipe temperature [W/°C]
𝑇𝑎𝑚𝑏 is the ambient temperature [°C]
Of course, as was the case with the 𝑈𝐴 value estimations of the heat exchangers, using this
method to approximately determine a single 𝑈𝐴 value neglects environmental effects (especially
wind speed) and system effects (such as flow velocity, mean fluid temperature etc). However, a
detailed analysis of the solar field heat losses was beyond the scope of this study, hence the same
method was utilised to experimentally determine a 𝑈𝐴 value of the pipes in the solar field. The
𝑈𝐴 value of the pipes was experimentally determined to be;
27
𝑈𝐴̅̅ ̅̅ 𝑝𝑖𝑝𝑒 = 18.26 𝑊
°𝐶
𝜎𝑈𝐴𝑝𝑖𝑝𝑒 = 2.079 𝑊
°𝐶
Where 𝑈𝐴̅̅ ̅̅ 𝑝𝑖𝑝𝑒 is the mean overall heat transfer coefficient in the solar field pipe [W/°C]
𝜎𝑈𝐴𝑝𝑖𝑝𝑒 is the standard deviation of 𝑈𝐴𝑝𝑖𝑝𝑒 [W/°C]
From the outlet of HX1 to the inlet of the solar collector field there is a small length of piping
with some losses as well. However these are ignored as in most cases the heat from compression
which is added by the pump is sufficient to render the net heat lost, to the ambient, negligible.
28
2.2.1 Modelling the MD loop
The MD loop itself cannot be modelled without experimentation on it first to observe and
analyse its performance and behaviour at different operating conditions. While doing the same, it
was observed that the performance indicators, namely the 𝑃𝑓𝑙𝑢𝑥, 𝑆𝑇𝐸𝐶, 𝐺𝑂𝑅 and 𝜀, had a
behaviour predictable with changing operating conditions. A regression analysis was performed,
with the results from the experiment runs (see Table 4 and Table 5), to model the performance
indicators as functions of the varied operating conditions i.e 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 , 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 and �̇�𝐹.
Experimental data was fitted to a quadratic function in [8], although only the 𝑃𝑓𝑙𝑢𝑥 and 𝑆𝑇𝐸𝐶
were modelled in that study, as it was found to have the best fit for the given data. In this study
it was similarly observed that a quadratic function best fit the experimental data for the 𝑃𝑓𝑙𝑢𝑥 and
𝑆𝑇𝐸𝐶 as well as the 𝐺𝑂𝑅 while in the case of the 𝜀 a linear regression model provided the best
fit.
The regression analysis was done using MATLAB and for the linear regression equation;
𝑦 = 𝑦0 + 𝑦1 ⋅ 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 + 𝑦2 ⋅ 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 + 𝑦3 ⋅ �̇�𝐹 Equation 20
the coefficients for 𝜀 were calculated and are presented in Table 2;
Table 2: Linear regression analysis for ε
Response Coefficient
𝜀
Estimate p-value
𝑦0 0.79723 1.1379 × 10−29
𝑦1 0.00034719 0.12625
𝑦2 0.0010569 1.3633 × 10−9
𝑦3 −0.00021779 3.8851 × 10−16
𝑅2 𝑣𝑎𝑙𝑢𝑒 0.957 Root mean square
error 0.0046
𝑂𝑣𝑒𝑟𝑎𝑙𝑙 𝑝 − 𝑣𝑎𝑙𝑢𝑒
8.38 × 10−16
The coefficient of determination i.e 𝑅2 𝑣𝑎𝑙𝑢𝑒 suggests that approximately 95.7% of the
variability in the response variable (𝜀) is explained by the model. Values of 𝑅2 close to 1 are
ideal. The p-value is an indicator of the significance of the term at the 5 % significance level
given to other terms. In other words, terms with p-values above 0.05 are not significant to the
model and may be ignored. For example, in the case of 𝜀, as the p-value of 𝑦1 is greater than
0.05, this term is not significant and is ignored. The root mean square error is the root mean
29
square of the differences between the experimental data values and the values predicted by the
model. The lower the root mean square error, the better is the statistical model.
With an overall 𝑝 − 𝑣𝑎𝑙𝑢𝑒 = 8.38 × 10−16 (should be below 0.05 to be significant) and a root
mean square error of 0.0046, it suggests that the above model is sufficient to evaluate 𝜀. The
final coefficients are then determined by fitting the experimental data with the significant terms.
Hence, in the case of 𝜀, Equation 20 becomes;
𝜀 = 0.80576 + 0.0010572 ⋅ 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 0.0002173 ⋅ �̇�𝐹 Equation 21
𝑅𝑜𝑜𝑡 𝑚𝑒𝑎𝑛 𝑠𝑞𝑢𝑎𝑟𝑒 𝑒𝑟𝑟𝑜𝑟 𝑜𝑓 𝜀 = 0.00474
𝑃𝑓𝑙𝑢𝑥, 𝑆𝑇𝐸𝐶 and 𝐺𝑂𝑅 were modelled by fitting their experimental data to a quadratic regression
equation given by;
𝑦 = 𝑦0 + 𝑦1 ⋅ 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 + 𝑦2 ⋅ 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 + 𝑦3 ⋅ �̇�𝐹 + 𝑦4 ⋅ 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 ⋅ 𝑇𝑒𝑣𝑎𝑝𝑖𝑛+ 𝑦5 ⋅ 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 ⋅ �̇�𝐹 + 𝑦6 ⋅ 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 ⋅ �̇�𝐹 + 𝑦7 ⋅ 𝑇𝑐𝑜𝑛𝑑𝑖𝑛
2
+ 𝑦8 ⋅ 𝑇𝑒𝑣𝑎𝑝𝑖𝑛2 + 𝑦9 ⋅ �̇�𝐹
2
Equation 22
The results of the regression analysis can be seen in Table 3;
Table 3: Regression analysis for Pflux, STEC and GOR
Response Coefficient
𝑃𝑓𝑙𝑢𝑥 𝑆𝑇𝐸𝐶 𝐺𝑂𝑅
Estimate p-value Estimate p-value Estimate p-value
𝑦0 1.3556 0.49434 881.22 0.0012808 −3.7195 0.19149
𝑦1 −0.091816 0.20262 0.78161 0.92489 −0.045854 0.64448
𝑦2 0.012884 0.7793 −20.105 0.0015325 0.20737 0.0046835
𝑦3 −0.012862 0.00012838 0.90971 0.0088802 −0.0081829 0.039997
𝑦4 0.00094343 0.048688 −0.079829 0.1459 0.0015117 0.027273
𝑦5 −6.6761× 10−5
0.15066 0.0027005 0.61225 −6.2798 × 10−5 0.32904
𝑦6 0.00031488 5.7305× 10−13
−0.010932 0.00054199 7.019 × 10−5 0.035588
𝑦7 0.00046585 0.71224 0.024264 0.87035 −1.6362 × 10−5 0.99265
𝑦8 −0.00039999 0.21543 0.15954 0.00043281 −0.0016426 0.0015926
𝑦9 1.0005 × 10−6 0.74618 2.5926× 10−5
0.9432 3.3181 × 10−6 0.4493
𝑅2 𝑣𝑎𝑙𝑢𝑒 0.996 0.96 0.961 Root mean square error
0.0754 8.88 0.106
𝑂𝑣𝑒𝑟𝑎𝑙𝑙 𝑝 − 𝑣𝑎𝑙𝑢𝑒
2.14 × 10−18 4.19 × 10−10 2.76 × 10−10
30
From Table 3 and Equation 22, the 𝑃𝑓𝑙𝑢𝑥, 𝑆𝑇𝐸𝐶 and 𝐺𝑂𝑅 can be modelled as;
𝑃𝑓𝑙𝑢𝑥 = − 0.010182 ⋅ �̇�𝐹 − 0.00015098 ⋅ 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 ⋅ 𝑇𝑒𝑣𝑎𝑝𝑖𝑛+ 0.00026597 ⋅ 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 ⋅ �̇�𝐹
Equation 23
𝑅𝑜𝑜𝑡 𝑚𝑒𝑎𝑛 𝑠𝑞𝑢𝑎𝑟𝑒 𝑒𝑟𝑟𝑜𝑟 𝑜𝑓 𝑃𝑓𝑙𝑢𝑥 = 0.106𝑙
ℎ ⋅ 𝑚2
𝑆𝑇𝐸𝐶 = 905.18 − 21.813 ⋅ 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 + 0.99132 ⋅ �̇�𝐹 − 0.010969
⋅ 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 ⋅ �̇�𝐹 + 0.1575 ⋅ 𝑇𝑒𝑣𝑎𝑝𝑖𝑛2
Equation 24
𝑅𝑜𝑜𝑡 𝑚𝑒𝑎𝑛 𝑠𝑞𝑢𝑎𝑟𝑒 𝑒𝑟𝑟𝑜𝑟 𝑜𝑓 𝑆𝑇𝐸𝐶 = 15.1𝑘𝑊ℎ
𝑚3
𝐺𝑂𝑅 = 0.08827 ⋅ 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 0.0092547 ⋅ �̇�𝐹 + 0.0005928
⋅ 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 ⋅ 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 + 9.1 × 10−5 ⋅ 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 ⋅ 𝑉𝐹− 0.0006754 ⋅ 𝑇𝑒𝑣𝑎𝑝𝑖𝑛
2
Equation 25
𝑅𝑜𝑜𝑡 𝑚𝑒𝑎𝑛 𝑠𝑞𝑢𝑎𝑟𝑒 𝑒𝑟𝑟𝑜𝑟 𝑜𝑓 𝐺𝑂𝑅 = 0.115
For a fixed set of input conditions (𝑇𝑐𝑜𝑛𝑑𝑖𝑛 , 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 and �̇�𝐹) 𝜀 can be calculated using Equation
21 and then the heat transfer through HX2 (𝑄𝐻𝑋2) using Equation 17. In this way the MD loop
can be modelled from an energetic scope. To determine the evaporator channel outlet
temperature, given only the 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 , 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 and �̇�𝐹, it is necessary to redefine 𝜀 as [20];
𝜀 =𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑒𝑣𝑎𝑝𝑜𝑢𝑡𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛
Equation 26
Where 𝑇𝑒𝑣𝑎𝑝𝑜𝑢𝑡 is the outlet of the evaporator channel [°C]
It is preferred to define 𝜀 in terms of the heat transfer/enthalpy in the condenser channel/cold
stream side, as in Equation 7, rather than in terms of the evaporator channel/hot stream side, as
in Equation 26 above. This is because the mass flow rate and salinity of the fluid stream remain
constant along the length of the condenser channel but, due to evaporation, the same does not
hold true in the evaporator channel. However, only for the purposes of determining the 𝑇𝑒𝑣𝑎𝑝𝑜𝑢𝑡
Equation 26 was utilised which when rearranged in terms of 𝑇𝑒𝑣𝑎𝑝𝑜𝑢𝑡 gives;
𝑇𝑒𝑣𝑎𝑝𝑜𝑢𝑡 = 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝜀 ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛) Equation 27
31
2.2.2 Limitations of mathematical model
The tank loop (see Figure 5) has not been mathematically modelled and hence the developed
model only describes the interaction between the solar loop and the MD loop without an
intermediary buffer/storage system. This was done for the following reasons;
- The tank loop, as explained earlier, acts chiefly as a buffer between the energy source
(solar collector field) and the energy sink (MD module). Its main role is to absorb the
fluctuations in incoming solar irradiation and ensure that the MD operation is not
disturbed. Thus for the sake of simplicity in a steady state analysis, it has been
overlooked and the solar loop is assumed to be directly coupled to the MD loop
- The time constraints of this study did not allow for a detailed analysis and
characterisation of the tank and the tank loop
Furthermore, the model was developed for a system operating in a steady state and hence cannot
be directly applied to an unsteady/transient system. In practical application, especially
considering a MD system coupled to a solar collector field, variations in environmental
parameters (such as solar irradiation, ambient temperature, wind velocity etc) may cause unsteady
operating conditions which may hamper the performance of the system. This topic is briefly
discussed in the following chapter with the operation of the auxiliary cooling system in the solar
field, in order to achieve steady state operation, when there is variable solar irradiation.
An optimisation analysis was not carried out in this study. A dual optimisation of the 𝑃𝑓𝑙𝑢𝑥 and
𝑆𝑇𝐸𝐶/𝐺𝑂𝑅, as carried out in [8], is of particular interest for MD operation as the highest
distillate production operation point and lowest energy consumption operation point do not
coincide and in most cases there is a trade-off between distillate production and energy
consumption [3], [8], [9], [18].
Finally, as the modelling of the PGMD module was carried out based on experimental results
from operation of the module within some set of operating conditions, hence the model itself is
only valid within this experiment matrix. The manufacturer’s specifications of the module allow
for operation well beyond the conditions specified in Chapter 2.1.1 especially with regards to the
�̇�𝐹 and 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 . This was the main reason why a multi-response optimisation was not performed,
as such an optimisation would not be reflected of the entire operational range of the PGMD
module.
32
3. Results and Discussion
3.1 Characterisation and performance evaluation of PGMD module
The performance indicators (𝑆𝑇𝐸𝐶, 𝐺𝑂𝑅, 𝑃𝑓𝑙𝑢𝑥 and 𝜀) at various operation points or
alternatively the results of the experiment runs are presented in Table 4 below. Secondary results,
from experiment runs conducted at �̇�𝐹 = 500 𝑙/ℎ, are shown in Table 5.
Table 4: Primary Experimental Results
𝑇𝑐𝑜𝑛𝑑𝑖𝑛 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 �̇�𝐹 𝑆𝑇𝐸𝐶 ∆𝑆𝑇𝐸𝐶 𝐺𝑂𝑅 ∆𝐺𝑂𝑅 𝑃𝑓𝑙𝑢𝑥 ∆𝑃𝑓𝑙𝑢𝑥 𝜀 ∆𝜀
°C °C l/h kWh/m3 kWh/m3 - - l/(h∙m2) l/(h∙m2) - -
20 60 200 251 32.9 2.67 0.350 1.098 0.0136 0.823 0.0209
20 60 300 266 29.5 2.52 0.279 1.744 0.0136 0.802 0.0198
20 60 400 292 31.2 2.29 0.244 2.236 0.0136 0.782 0.0207
20 70 200 218 24.6 3.07 0.346 1.484 0.0137 0.834 0.0167
20 70 300 228 23.3 2.93 0.300 2.363 0.0137 0.820 0.0164
20 70 400 260 26.4 2.57 0.275 3.201 0.0137 0.792 0.0187
20 80 200 200 20.6 3.33 0.343 2.017 0.0137 0.838 0.0152
20 80 300 219 21.0 3.04 0.292 3.064 0.0137 0.821 0.0152
20 80 400 233 19.7 2.85 0.240 4.135 0.0137 0.803 0.0148
25 60 200 224 32.6 2.99 0.436 1.002 0.0137 0.832 0.0223
25 60 300 266 33.2 2.52 0.315 1.518 0.0137 0.804 0.0220
25 60 400 300 34.1 2.23 0.254 1.981 0.0137 0.779 0.0223
25 70 200 196 26.6 3.42 0.465 1.405 0.0137 0.846 0.0192
25 70 300 216 27.2 3.08 0.388 2.347 0.0137 0.813 0.0213
25 70 400 237 25.5 2.81 0.303 3.089 0.0137 0.794 0.0199
25 80 200 182 22.6 3.65 0.455 1.861 0.0136 0.850 0.0169
25 80 300 208 23.2 3.20 0.359 2.904 0.0136 0.826 0.0173
25 80 400 217 22.4 3.06 0.316 4.103 0.0137 0.802 0.0183
30 60 200 207 33.8 3.23 0.526 0.965 0.0137 0.826 0.0259
30 60 300 258 37.9 2.59 0.380 1.345 0.0137 0.801 0.0263
30 60 400 299 44.6 2.24 0.334 1.743 0.0137 0.779 0.0293
30 70 200 183 27.2 3.65 0.541 1.352 0.0137 0.845 0.0211
30 70 300 199 25.3 3.36 0.428 2.226 0.0137 0.816 0.0212
30 70 400 212 23.9 3.14 0.354 3.046 0.0137 0.798 0.0205
30 80 200 180 22.3 3.70 0.459 1.841 0.0136 0.840 0.0181
30 80 300 188 22.5 3.53 0.421 2.841 0.0136 0.828 0.0187
30 80 400 193 20.1 3.44 0.359 4.076 0.0136 0.812 0.0178
33
Table 5: Secondary Experimental Results
𝑇𝑐𝑜𝑛𝑑𝑖𝑛 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 �̇�𝐹 𝑆𝑇𝐸𝐶 ∆𝑆𝑇𝐸𝐶 𝐺𝑂𝑅 ∆𝐺𝑂𝑅 𝑃𝑓𝑙𝑢𝑥 ∆𝑃𝑓𝑙𝑢𝑥 𝜀 ∆𝜀
°C °C l/h kWh/m3 kWh/m3 - - l/(h∙m2) l/(h∙m2) - -
20 70 500 294 25.6 2.27 0.198 3.900 0.0137 0.770 0.0187
25 60 500 329 35.3 2.04 0.219 2.467 0.0137 0.760 0.0227
25 70 500 288 32.9 2.31 0.264 3.541 0.0137 0.768 0.0234
3.1.1 Variation with feed flow rate (�̇�𝐹)
The variation of the three main performance indicators 𝑃𝑓𝑙𝑢𝑥, 𝑆𝑇𝐸𝐶 and 𝐺𝑂𝑅 with �̇�𝐹, at
different 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 keeping 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 = 25 ℃ constant, is shown in Figure 7, Figure 8 and Figure 9
respectively.
Figure 7: Distillate flux vs feed flow rate at condenser inlet temperature 25 °C
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
100 200 300 400 500 600
Dis
tilla
te f
lux
(l/(
h∙m
2))
Feed flow rate (l/h)
Tevap = 60 °C
Tevap = 70 °C
Tevap = 80 °C
34
Figure 8: STEC vs feed flow rate at condenser inlet temperature 25 °C
Figure 9: GOR vs feed flow rate at condenser inlet temperature 25 °C
As can be observed from Figure 7, as the �̇�𝐹 increases 𝑃𝑓𝑙𝑢𝑥 increases as well. This can be
attributed to an increase in the driving force (vapour pressure difference across the membrane)
brought on by a decreased thermal boundary layer on the membrane surface in the evaporator
channel as well as a better heat transfer within this limiting boundary layer due to the higher flow
rate. In other words the temperature polarisation (the temperature difference between the
membrane surface and the bulk fluid temperature) is reduced due to the higher �̇�𝐹. The
reduction in the temperature polarisation leads to an increase in the transmembrane temperature
difference, which in turn increases the vapour pressure difference/driving force. The
effectiveness of internal heat exchange (𝜀) decreases with an increase in �̇�𝐹 (see Table 4 and
Equation 21) and hence the permeate side of the membrane remains at a lower temperature
150
200
250
300
350
400
100 200 300 400 500 600
STEC
(kW
h/m
3)
Feed flow rate (l/h)
Tevap = 60 °C
Tevap = 70 °C
Tevap = 80 °C
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
100 200 300 400 500 600
GO
R
Feed flow rate (l/h)
Tevap = 60 °C
Tevap = 70 °C
Tevap = 80 °C
35
which further increases the temperature differential and driving force. Thus the 𝑃𝑓𝑙𝑢𝑥 is
positively related to �̇�𝐹.
It is inherently apparent that the heat required to lift a fluid’s temperature between two fixed
temperature limits must increase with an increase in its thermal capacitance. The thermal
capacitance, in this case, increasing chiefly due to an increase in �̇�𝐹. Referring to Equation 16,
with other variables constant, the 𝑄𝐻𝑋2 must increase to match an increase in the �̇�𝐹. Besides
this, a falling 𝜀 with rising �̇�𝐹 implies that the condenser outlet temperature (𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡) decreases
and as can be inferred from Equation 16, this increases the 𝑄𝐻𝑋2. As can be seen from Figure 8
and Figure 9, this increase is large enough to offset the increase in the distillate production and
hence with higher �̇�𝐹, the 𝑆𝑇𝐸𝐶 rises and 𝐺𝑂𝑅 falls.
Alternatively it can be stated that with a larger �̇�𝐹, the distillate production rate increases but
each unit of distillate produced requires more thermal energy than at a lower �̇�𝐹.
Employing the mathematical model, the increase in driving force (represented by an increase in
the average temperature difference between the evaporator and condenser channels) leads to an
increase in distillate production with rising �̇�𝐹 as can be seen in Figure 10. However the rise in
the heat required 𝑄𝐻𝑋2 (see Figure 11) far outpaces this increase as can be observed by
comparing the magnitude of the difference between the final and initial y-axis values in Figure 10
and Figure 11. Hence an overall rise in the 𝑆𝑇𝐸𝐶, and a fall in the 𝐺𝑂𝑅, can be predicted with
increasing �̇�𝐹.
Figure 10: Temperature differential driving force vs feed flow rate
36
Figure 11: Heating power required vs feed flow rate
The model here utilised a 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 = 70 ℃ and 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 = 25 ℃ to generate Figure 10 and
Figure 11.
Additionally it can be observed that at higher 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 there is a better performance both in terms
of distillate production rate (𝑃𝑓𝑙𝑢𝑥) as well as energy efficiency (𝑆𝑇𝐸𝐶 and 𝐺𝑂𝑅). This effect of
the evaporator inlet temperature will be dealt with in more depth in the following section.
37
3.1.2 Variation with evaporator inlet temperature (𝑇𝑒𝑣𝑎𝑝𝑖𝑛)
The variation of the three main performance indicators 𝑃𝑓𝑙𝑢𝑥, 𝑆𝑇𝐸𝐶 and 𝐺𝑂𝑅 with 𝑇𝑒𝑣𝑎𝑝𝑖𝑛,
at different 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 keeping �̇�𝐹 = 200𝑙
ℎ constant, is shown in Figure 12, Figure 13 and Figure 14
respectively.
Figure 12: Distillate flux vs evaporator inlet temperature at feed flow rate of 200 l/h
Figure 13: STEC vs evaporator inlet temperature at feed flow rate of 200 l/h
0.8
1.0
1.2
1.4
1.6
1.8
2.0
2.2
50 55 60 65 70 75 80 85
Dis
tilla
te f
lux
(l/
(h∙m
2 ))
Evaporator inlet temperature (°C)
Tcond = 20 °C
Tcond = 25 °C
Tcond = 30 °C
150
170
190
210
230
250
270
290
310
50 55 60 65 70 75 80 85
STEC
(kW
h/m
3 )
Evaporator inlet temperature (°C)
Tcond = 20 °C
Tcond = 25 °C
Tcond = 30 °C
38
Figure 14: GOR vs evaporator inlet temperature at feed flow rate of 200 l/h
A rise in the 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 , keeping the 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 constant, increases the transmembrane
temperature difference which directly increases the vapour pressure difference and hence the
driving force behind the distillation. This behaviour is reflected in Figure 12 where the 𝑃𝑓𝑙𝑢𝑥
continuously increases with increasing 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 .
However to attain these higher 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 , a larger supply of heat is required (other variables
remaining the same) and hence the 𝑄𝐻𝑋2 also rises with a rise in 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 . This can be easily
understood by referring to Equation 16.
Unlike in the case with �̇�𝐹, the increase in the distillate flow rate is large enough to offset the
increase in the thermal energy consumption of the system and hence the 𝑆𝑇𝐸𝐶 falls and the
𝐺𝑂𝑅 rises continuously with an increasing 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 as can been observed in Figure 13 and Figure
14.
Thus operating at a higher 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 implies both a higher distillate production rate as well as a
lower thermal energy consumption per unit of distillate produced. This double benefit can be
viewed in terms of the variation in the 𝜀. From the Table 4 and Equation 21, it can be seen that
there is a small positive correlation between 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 and 𝜀 which means that the average
condenser temperature should slightly increase but as this increase is much lower than the
increase in the average evaporator temperature, the transmembrane temperature differential
increases and hence the distillate production 𝑃𝑓𝑙𝑢𝑥 increases. The heat required 𝑄𝐻𝑋2 still
increases though, despite the increase in 𝜀, as the magnitude of increase of 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 is not
matched by a similar increase in 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡 .
This behaviour can also be explained using the developed mathematical model. With the rising
𝑇𝑒𝑣𝑎𝑝𝑖𝑛 and 𝜀, the 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡 also increases (see Figure 15) but cannot match the increase in
𝑇𝑒𝑣𝑎𝑝𝑖𝑛 (see Figure 16).
2.0
2.5
3.0
3.5
4.0
4.5
50 55 60 65 70 75 80 85
GO
R
Evaporator inlet temperature (°C)
Tcond = 20 °C
Tcond = 25 °C
Tcond = 30 °C
39
The driving force hence also increases and the same can be represented by plotting the
average temperature difference that exists between the evaporator and condenser channels as can
be seen in Figure 17. It should be noted that the model used 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 = 20 ℃ and �̇�𝐹 = 200𝑙
ℎ
when generating Figure 15, Figure 16 and Figure 17.
Figure 17: Temperature differential driving force vs evaporator inlet temperature
Figure 15: Condenser outlet temperature vs evaporator inlet
temperature
Figure 16: Temperature difference between evaporator inlet and
condenser outlet temperatures vs evaporator inlet temperature
40
3.1.3 Variation with condenser inlet temperature (𝑇𝑐𝑜𝑛𝑑𝑖𝑛)
The variation of the three main performance indicators 𝑃𝑓𝑙𝑢𝑥, 𝑆𝑇𝐸𝐶 and 𝐺𝑂𝑅 with 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 ,
at different �̇�𝐹, keeping 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 = 70 ℃ constant, is shown in Figure 18, Figure 19 and Figure
20 respectively.
Figure 18: Distillate flux vs condenser inlet temperature at evaporator inlet temperature of 70°C
Figure 19: STEC vs condenser inlet temperature at evaporator inlet temperature of 70°C
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
18 20 22 24 26 28 30 32
Dis
tilla
te f
lux
(l/(
h.m
2 ))
Condenser inlet temperature (°C)
Vf = 200 l/h
Vf = 300 l/h
Vf = 400 l/h
Vf = 500 l/h
150
170
190
210
230
250
270
290
310
330
18 20 22 24 26 28 30 32
STEC
(kW
h/m
3 )
Condenser inlet temperature (°C)
Vf =200 l/h
Vf = 300 l/h
Vf = 400 l/h
Vf = 500 l/h
41
Figure 20: GOR vs condenser inlet temperature at evaporator inlet temperature of 70°C
The driving force continuously decreases with an increase in the 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 as the temperature
difference in the evaporator and condenser channel narrows. Thus, the distillate production and
flux 𝑃𝑓𝑙𝑢𝑥 fall in Figure 18 although the decrease is relatively small. The heat required to drive
the MD process must also decline as the 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 , and hence the 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡 , draw closer to the
𝑇𝑒𝑣𝑎𝑝𝑖𝑛 . It can be observed in Figure 19 and Figure 20 that the energy required to produce a unit
volume of distillate continuously decreases with increasing 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 . Hence the effect of
decreasing heat required is consistently larger than the effect of decreasing distillate production
at higher 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 . Therefore, it can be summarised that the distillate production marginally
decreases with increasing 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 but the energy cost for producing a unit of distillate also falls.
Note that, from Table 4 and Equation 21, the effectiveness 𝜀 is virtually independent of 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 .
The mathematical model developed confirms the above findings with the driving force, and thus
distillate production, along with the heat required predicted to fall (see Figure 21 and Figure 22)
1.7
2.2
2.7
3.2
3.7
4.2
4.7
18 20 22 24 26 28 30 32
GO
R
Condenser inlet temperature (°C)
Vf =200 l/h
Vf = 300 l/h
Vf = 400 l/h
Vf = 500 l/h
Figure 21: Temperature differential driving force vs condenser inlet temperature
42
Figure 22: Heating power required vs condenser inlet temperature
The model assumed a 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 = 70 ℃ and �̇�𝐹 = 300𝑙
ℎ while generating Figure 21 and
Figure 22.
3.1.4 Repetition of experiment run
To check the accuracy of the experiments vis-à-vis experiment errors, variation of
performance parameters and system stability over time, a random experiment run was selected
and performed 3 times on different days. The experiment run chosen was;
𝑇𝑒𝑣𝑎𝑝𝑖𝑛 = 70 ℃, 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 = 20 ℃ and �̇�𝐹 = 300𝑙
ℎ
The results of the three runs are shown in Table 6 below. As can be seen, there were fairly
small deviations between experiment runs given the magnitude of the respective errors in final
values due to propagation of errors.
Table 6: Results from experiment run repetition
Experiment 𝑆𝑇𝐸𝐶 ∆𝑆𝑇𝐸𝐶 𝐺𝑂𝑅 ∆𝐺𝑂𝑅 𝑃𝑓𝑙𝑢𝑥 ∆𝑃𝑓𝑙𝑢𝑥
kWh/m3 kWh/m3 - - l/(h∙m2) l/(h∙m2)
1 228 23.3 2.93 0.300 2.363 0.0137
2 243 24.8 2.74 0.280 2.347 0.0137
3 235 26.8 2.84 0.323 2.376 0.0137
Mean 235 25.0 2.84 0.301 2.362 0.0137
Std Dev 6 1.4 0.08 0.017 0.012 0.0000
43
3.1.5 Validation and comparison of experimental results
The results from the experiment campaign on the PGMD module yielded results that match
well with expected trends and conclusions from previous studies and experimental works using
the same type and construction of MD module i.e spiral wound PGMD [3], [8]–[10]. While the
size of the module was slightly different from the ones used in other works, the performance
indicators were within the expected range.
Experimental results were compared with findings from [8] and are presented in Figure 23,
Figure 24 and Figure 25.
Tcond = 20 °CTevap = 60 °CVf = 400 l/h
Tcond = 20 °CTevap = 80 °CVf = 400 l/h
Tcond = 30 °CTevap = 60 °CVf = 400 l/h
Tcond = 30 °CTevap = 80 °CVf = 400 l/h
Tcond = 25 °CTevap = 70 °CVf = 400 l/h
Tcond = 25 °CTevap = 70 °CVf = 500 l/h
Tcond = 25 °CTevap = 60 °CVf = 500 l/h
Tcond = 20 °CTevap = 70 °CVf = 500 l/h
Ruiz et al [8] 1 1.97 0.85 1.77 1.38 1.76 1.13 1.87
Current study 2.24 4.14 1.74 4.08 3.09 3.54 2.47 3.90
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
Dis
tilla
te f
lux
(l/
h.m
2 )
Tcond = 20 °CTevap = 60 °CVf = 400 l/h
Tcond = 20 °CTevap = 80 °CVf = 400 l/h
Tcond = 30 °CTevap = 60 °CVf = 400 l/h
Tcond = 30 °CTevap = 80 °CVf = 400 l/h
Tcond = 25 °CTevap = 70 °CVf = 400 l/h
Tcond = 25 °CTevap = 70 °CVf = 500 l/h
Tcond = 25 °CTevap = 60 °CVf = 500 l/h
Tcond = 20 °CTevap = 70 °CVf = 500 l/h
Ruiz et al [8] 302.47 224.13 305.4 234.56 257.12 266.84 322.46 315.61
Current study 292 233.36 298.76 192.91 236.84 288.10 328.54 293.95
0
50
100
150
200
250
300
350
STEC
(kW
h/m
3 )
Figure 24: Comparison of distillate fluxes between current study and [8]
Figure 23: Comparison of STEC between current study and [8]
44
As can be seen from Figure 24, the 𝑃𝑓𝑙𝑢𝑥 of the current PGMD module is consistently and
considerably higher than the PGMD module tested in [8]. The 𝑆𝑇𝐸𝐶 and 𝐺𝑂𝑅 of both modules
are almost on par and no conclusive inference can be drawn from Figure 23 and Figure 25
regarding the relative energy performance of one module over the other.
In [10], a spiral wound PGMD module with a membrane area of 10 m2 was found to have
𝑃𝑓𝑙𝑢𝑥 = 1.33𝑙
ℎ⋅𝑚2 and 𝑆𝑇𝐸𝐶 = 142𝑘𝑊ℎ
𝑚3 at 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 = 25 ℃, 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 = 80 ℃ and �̇�𝐹 =
300𝑘𝑔
ℎ (≅ �̇�𝐹 = 300
𝑙
ℎ ). By comparison, the current module, at the same operating conditions,
had 𝑃𝑓𝑙𝑢𝑥 = 2.904𝑙
ℎ⋅𝑚2 and 𝑆𝑇𝐸𝐶 = 208
𝑘𝑊ℎ
𝑚3.
Hence the distillate production rate of the current spiral wound PGMD module is significantly
higher than that of earlier modules while its energy consumption is comparable. The
improvement in the distillate production rate can be attributed to an increased driving force. The
driving force may be increased due to a reduction in the temperature polarisation in the PGMD
module channels which in turn might be due to changes in the design and construction of the
spacers placed in the flow channels to increase the turbulence and hence reduce the temperature
difference between the fluid bulk and the membrane surface i.e the temperature polarisation.
Differences in the channel widths lead to different flow velocities, at the same volumetric flow
rate, and this may also lead to changes in the driving force. Of course, the differences in the
membranes themselves, each having their own permeability, tortuosity and porosity, cause
variations in the mass transfer (as well as heat transfer) resistance which directly impacts the
driving force. A more thorough analysis of the individual spiral wound PGMD modules needs to
be carried out to reveal the exact cause(s) of this increased driving force however this is beyond
the scope of the current work.
Tcond = 20 °CTevap = 60 °CVf = 400 l/h
Tcond = 20 °CTevap = 80 °CVf = 400 l/h
Tcond = 30 °CTevap = 60 °CVf = 400 l/h
Tcond = 30 °CTevap = 80 °CVf = 400 l/h
Tcond = 25 °CTevap = 70 °CVf = 400 l/h
Tcond = 25 °CTevap = 70 °CVf = 500 l/h
Tcond = 25 °CTevap = 60 °CVf = 500 l/h
Tcond = 20 °CTevap = 70 °CVf = 500 l/h
Ruiz et al [8] 2.22 2.96 2.18 3.24 2.63 2.5 2.1 2.13
Current study 2.29 2.85 2.24 3.44 2.81 2.31 2.04 2.27
0
0.5
1
1.5
2
2.5
3
3.5
GO
R
Figure 25: Comparison of GOR between current study and [8]
45
0.45
0.47
0.49
0.51
0.53
0.55
0.57
0.59
0.61
13:55:12 14:02:24 14:09:36 14:16:48 14:24:00 14:31:12 14:38:24 14:45:36 14:52:48 15:00:00 15:07:12
Sola
r C
olle
cto
r E
ffic
ien
cy
Time of day
Model
Exp
3.2 Analysis with Mathematical Model
3.2.1 Validation of mathematical model of solar loop
To validate the model of the solar collector field, experimental runs were made to test the
accuracy of the theoretical predictions with experimental results. The overall efficiency of the
solar collector field was estimated using Equation 10 and compared with experimental findings
using Equation 12. An uncertainty analysis of the same can be found in Appendix D.
Figure 26 below shows the comparison of the theoretically and experimentally determined
efficiency of solar collection during an hour’s long steady state experiment. The experiment was
carried out on 02/02/2018 between 14:00-15:00 local time (no daylights savings). As the data is
plotted for every second of the hour the individual data points are impossible to distinguish and
this holds true for the error bars as well.
Figure 26: Theoretical and experimental solar collector efficiency
The average relative error was found to be 4 %. This was deemed to be within the
acceptable limit of accuracy, given the propagation of error and uncertainties in the
measurements themselves, and hence the mathematical modelling of the solar collector field is
experimentally validated. The differences in the efficiencies arise because of the approximation
of the total collector area as one large collector instead of treating it as 4 different collectors
connected in series. Additionally, there is a capacitance effect where the collector outlet
temperature does not change quickly with changes to the collector inlet temperature which
continuously rises due to the charging tank. As the tank heats up, the temperature at the inlet to
the heat exchanger from the tank increases and hence the solar collector inlet temperature also
increases. However, the solar collector outlet temperature doesn't rise immediately due to the
thermal capacitance and this raises the average collector temperature. This capacitance effect
provides another source of error besides ambient conditions such as wind, humidity etc which
are ignored in the theoretical model.
46
3.2.2 Validation of MD module and loop
To validate the MD module and loop operation using the model, it is tested against the
experimental data from the experiment runs. The following experiment runs were randomly
chosen to test the accuracy of the model;
𝑇𝑒𝑣𝑎𝑝𝑖𝑛 = 70 ℃, 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 = 25 ℃, �̇�𝐹 = 200, 300, 400 𝑎𝑛𝑑 500𝑙
ℎ
The parameter evaluated theoretically and experimentally is the heat required 𝑄𝐻𝑋2 and the
results from the trials can be seen in Figure 27.
Figure 27: Theoretical and experimental heat required
The average relative error was 4 %. Given the error propagation and uncertainties in
measurements (see Appendix D for a more detailed uncertainty analysis), this deviation falls
within the acceptable range of error. Thus the mathematical model of the MD module can be
said to be experimentally validated.
47
3.2.3 Minimum radiation required for MD operation
Using the mathematical model and applying some simplifying assumptions, it is possible to
derive the minimum global solar radiation (on the titled plane/collector surface) required to
operate the MD module at different conditions. The exact mathematical manipulations and
assumptions made are discussed in detail in Appendix F. As can be observed in Table 7, the
behaviour of minimum solar radiation required at various operating conditions is the same as
that of heat required for MD operation 𝑄𝐻𝑋2.
Table 7: Minimum solar radiation required at different MD operating conditions
𝑇𝑐𝑜𝑛𝑑𝑖𝑛 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 �̇�𝐹 𝐺𝑇 ∆𝐺𝑇
°C °C l/h W/m2 W/m2
20 60 200 286.9 1.06
20 60 300 317.5 1.63
20 60 400 353.5 2.21
20 70 200 353.5 1.37
20 70 300 390.5 2.09
20 70 400 434.3 2.85
20 80 200 423.1 1.69
20 80 300 466.1 2.58
20 80 400 517.5 3.51
25 60 200 284.3 0.93
25 60 300 311.7 1.43
25 60 400 343.8 1.94
25 70 200 351.0 1.24
25 70 300 384.8 1.89
25 70 400 424.7 2.57
25 80 200 420.7 1.55
25 80 300 460.5 2.37
25 80 400 508.1 3.22
30 60 200 281.7 0.80
30 60 300 305.9 1.23
30 60 400 334.0 1.67
30 70 200 348.5 1.10
30 70 300 379.1 1.68
30 70 400 415.1 2.29
30 80 200 418.4 1.41
30 80 300 455.0 2.16
30 80 400 498.7 2.93
48
3.2.4 Auxiliary cooling required in solar loop for steady state operation
In practice it is often desired to operate in steady state conditions and not in fluctuating
conditions brought on by variations in incoming solar irradiation. Given that, within the scope of
this study, there is only a single heat source, the solar collector field, hence there is no possibility
of additional heating if the irradiation is insufficient. However, cooling may be carried out in the
case of excessive irradiation. To this end, the mathematical model is applied to determine the
auxiliary cooling necessary to maintain a near-constant heat exchanger (on the solar side) input at
higher than required solar irradiations for a given set of operating conditions (see Table 7). A
detailed explanation on the mathematical manipulations as well as simplifying assumptions made
can be found in Appendix F.
Table 8: Auxiliary cooling required for steady state operation at 700 W/m2 total irradiation on slope
𝑇𝑐𝑜𝑛𝑑𝑖𝑛 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 �̇�𝐹 𝑄𝑐𝑜𝑜𝑙𝑖𝑛𝑔 ∆𝑄𝑐𝑜𝑜𝑙𝑖𝑛𝑔
°C °C l/h kW kW
20 60 200 13.9 0.04
20 60 300 12.9 0.05
20 60 400 11.7 0.07
20 70 200 11.6 0.05
20 70 300 10.4 0.07
20 70 400 9.0 0.09
20 80 200 9.3 0.06
20 80 300 7.9 0.09
20 80 400 6.3 0.12
25 60 200 14.0 0.03
25 60 300 13.1 0.05
25 60 400 12.0 0.06
25 70 200 11.7 0.04
25 70 300 10.6 0.06
25 70 400 9.3 0.09
25 80 200 9.4 0.05
25 80 300 8.1 0.08
25 80 400 6.6 0.11
30 60 200 14.0 0.03
30 60 300 13.3 0.04
30 60 400 12.3 0.06
30 70 200 11.8 0.04
30 70 300 10.8 0.06
30 70 400 9.6 0.08
30 80 200 9.5 0.05
30 80 300 8.3 0.07
30 80 400 6.9 0.10
49
4. Further Discussion
4.1 Operation with solar thermal collector field
This section will delve into general principles and guidelines to improved operation of a MD
system in conjunction with a solar collector system. The following is based on operational
experience as well as previous studies [5], [7], [11], [12], [17];
- First the desired steady state operation point for the MD module must be decided. It
may be based on optimising 𝑃𝑓𝑙𝑢𝑥, 𝑆𝑇𝐸𝐶/𝐺𝑂𝑅 or both. This fixes the 𝑇𝑒𝑣𝑎𝑝𝑖𝑛, 𝑇𝑐𝑜𝑛𝑑𝑖𝑛
and �̇�𝐹
- Matched flow on either side of a heat exchanger provides the best heat transfer rate and
hence the flow rate in the solar collector loop should aim to match �̇�𝐹
Depending on whether the overall system’s objective is for maximum daily production
(operation spread over a longer time period per day) or simply for steady state operation during
permitting sunshine hours, a storage tank or inertia tank may be used respectively. Each case
must be treated separately because of their different objectives.
4.1.1 System with inertia tank
- The solar collector outlet temperature may then be fixed to a few degrees above the
𝑇𝑒𝑣𝑎𝑝𝑖𝑛 . This is because solar collector efficiency declines at higher operating
temperatures as can be seen in Figure 28 below. While Figure 28 has been drawn using
Equation 10 and the characteristics for the flat plate collector used in this study, the
negative relation between mean collector temperature and collector efficiency holds true
for all collectors. Besides for overcoming environmental heat losses, there is no reason to
operate the solar collector at temperatures much higher than 𝑇𝑒𝑣𝑎𝑝𝑖𝑛.
50
Figure 28: Solar collector efficiency vs average collector temperature at 25°C ambient
- In order to limit the solar collector operating temperature, especially when the irradiation
is higher than required, an auxiliary cooler must be employed. Of course, as discussed in
Chapter 3.2.4 , the cooling required is a function of the incident irradiation and is hence
variable in nature. Some active variable control, such as a PID controller, must thus be
implemented to deliver the necessary degree of cooling.
4.1.2 System with storage tank
- The solar collector temperature in this case does not need to be restricted and it may be
allowed to rise, within limits of its operation, to charge the storage tank to a higher
temperature than required for MD operation. High temperature tank charging allows for
operation of the MD unit even after the irradiation levels fall below the minimum
required.
- Of course during the course of tank charging the tank’s temperature will rise and so will
it’s outlet temperature to the heat exchanger connected to the MD loop. In order to
regulate this temperature, the return from the heat exchanger needs to be suitably mixed
with the tank’s outlet to the MD loop. An active tempering valve needs to be utilised for
this purpose and its setting needs to be actively controlled, potentially by PID control, to
obtain the desired temperature to the heat exchanger with the MD loop.
51
4.2 Future areas of interest and investigation
With respect to the current specific PGMD module used in this study, a complete
characterisation of the module, within its operational limits, would reveal its maximum 𝑃𝑓𝑙𝑢𝑥,
𝐺𝑂𝑅 and minimum 𝑆𝑇𝐸𝐶. The module has the capacity to operate at �̇�𝐹 = 700𝑙
ℎ which is far
above the highest level used in this study. Moreover, the upper limit of 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 could be raised
to analyse the performance of the module at elevated condenser temperatures which may be the
case in regions (especially in the Arabian gulf) with higher seawater temperatures. The PGMD
module’s 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 upper operational limit, provided by the manufacturer, was 90 °C which is not
much higher than the 80 °C used in this investigation however is still an are for further study.
Spiral wound modules are especially sensitive to the 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 because at elevated temperatures the
seals and adhesives, used in its construction, are degraded and eventually fail causing leakages. It
is for this reason that a 10 °C margin of safety was used. A full characterisation of the PGMD
module would allow for an optimisation analysis into the optimum operation conditions for
maximum distillate production and minimum energy consumption. Lastly, an investigation into
the effects of inlet feed water salinity should be carried out to test the variation in performance at
different concentration levels. This, along with an investigation with increased 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 , would
give an idea about the suitability for batch operation. Batch operation here refers to the mixing
of the inlet feedwater with some proportion of the outgoing brine.
More generally, a comparative study should be made of different control strategies and
configurations of MD systems coupled to solar thermal collectors vis-à-vis solar fraction,
distillate production etc. A detailed investigation could also be carried out into the optimal
placement of nodes on a storage tank and inertia tank which is important given the low
temperature drop (around 8 °C) observed across the heat exchanger with the MD loop. To
preserve the stratification of the tank, care must be taken to place the returning node at the
appropriate height.
Electrical consumption is often ignored as it is much smaller in magnitude than the heat
consumption. However this facet must not be completely neglected and future studies must
consider it as well as it’s especially useful for off-grid stand alone system design and application
[5], [6] which requires some source of electrical energy as well.
With respect to the mathematical model developed, it would be interesting to see the utility and
insightfulness of employing the effectiveness of internal heat recovery as a means of modelling
the MD module. As it was observed in this study, a linear regression analysis of the effectiveness
provided a simple yet accurate tool to model the PGMD unit at different operating conditions. A
more detailed mathematical model could be developed and would need to consider the
storage/inertia tank operation as well as more thoroughly analyse the system’s heat losses to the
environment and the heat transfer process through the heat exchangers. Besides this, the current
model developed simply considered the PGMD module from a thermal energy consumption
standpoint but a more complete model would have to consider the distillate production as well.
52
5. Conclusions
A complete characterisation of a precommercial spiral wound Permeate Gap Membrane
Distillation (PGMD) module, for the purpose of seawater (3.5 %) desalination, has been carried
out to determine the performance of the PGMD module at different operating conditions. The
performance indicators utilised in this study were the distillate flux (𝑃𝑓𝑙𝑢𝑥), specific thermal
energy consumption (𝑆𝑇𝐸𝐶) and the gross output ratio (𝐺𝑂𝑅). The operating variables varied
were the evaporator inlet temperature (𝑇𝑒𝑣𝑎𝑝𝑖𝑛), condenser inlet temperature (𝑇𝑐𝑜𝑛𝑑𝑖𝑛) and the
feed flow rate (�̇�𝐹). These three operating variables were set at the following levels;
𝑇𝑒𝑣𝑎𝑝𝑖𝑛 = 60 ℃, 70 ℃, 80 ℃
𝑇𝑐𝑜𝑛𝑑𝑖𝑛 = 20 ℃, 25 ℃, 30 ℃
�̇�𝐹 = 200𝑙
ℎ, 300
𝑙
ℎ, 400
𝑙
ℎ
Within this experiment matrix, the highest distillate flux 𝑃𝑓𝑙𝑢𝑥 = 4.135𝑙
ℎ.𝑚2 was recorded at
𝑇𝑒𝑣𝑎𝑝𝑖𝑛 = 80 ℃, 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 = 20 ℃, �̇�𝐹 = 400𝑙
ℎ. This equates to a distillate production rate of
21.3𝑙
ℎ. The lowest specific thermal consumption 𝑆𝑇𝐸𝐶 = 180
𝑘𝑊ℎ
𝑚3 and highest gross output
ratio 𝐺𝑂𝑅 = 3.7 simultaneously occurred at 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 = 80 ℃, 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 = 30 ℃, �̇�𝐹 = 200𝑙
ℎ.
These results were found to be consistent with previous studies and indicate a considerable
improvement in the distillate production rate over previous PGMD modules of the spiral wound
construction. There was no noticeable change in the specific thermal energy consumption in the
studied PGMD module over previously studied modules.
Additionally, three experiment runs were made at a higher feed flow rate. The three experiment
runs were at operating conditions;
1. 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 = 70 ℃, 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 = 20 ℃, �̇�𝐹 = 500𝑙
ℎ
2. 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 = 60 ℃, 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 = 25 ℃, �̇�𝐹 = 500𝑙
ℎ
3. 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 = 70 ℃, 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 = 25 ℃, �̇�𝐹 = 500𝑙
ℎ
Maximum distillate production rate of the PGMD module is expected to be higher as, according
to the manufacturer’s specifications, it can operate at a maximum feed flow rate of 700𝑙
ℎ and a
maximum evaporator inlet temperature of 90 ℃. An increase in either of these operating
parameters would lead to an increase in the distillate production rate.
A simplified generic mathematical model of a flat plate solar collector field coupled with a MD
module was developed, and experimentally validated, to further analyse the overall system. The
model was used to derive the minimum global irradiation (on the collector plane) required to
operate the MD module at steady state as well as auxiliary cooling required in the solar collector
53
field to regulate the operating temperature of the MD operation and ensure steady state
conditions of operation.
Modelling of the spiral wound PGMD module utilised a novel method of evaluation namely
through the effectiveness of internal heat exchange between the evaporator and condenser
channels. This parameter, which was found to vary linearly with the evaporator inlet temperature
and feed flow rate, could be used to accurately model the PGMD module (in temperature and
energy terms).
Finally, general guidelines and principles toward optimum usage of a solar thermal collector
system in conjunction with a MD system, using inertia or storage tanks, were presented and
discussed.
54
6. References
Book [3] D. Winter, Membrane distillation: a thermodynamic, technological and economic analysis. Aachen:
Shaker, 2015. [17] J. A. Duffie and W. A. Beckman, Solar engineering of thermal processes, 4. ed. New York: Wiley,
2013. [20] J. H. Lienhard IV and J. H. Lienhard V, A Heat Transfer Textbook, Fourth. Cambridge,
Massachusetts, U.S.A: Phlogiston Press, 2017.
Book chapter
[13] M. Conde, ‘Thermophysical properties of brines’, in Properties of working fluids, M. Conde
Engineering, 2011.
Journal Article
[5] J. Koschikowski, M. Wieghaus, M. Rommel, V. S. Ortin, B. P. Suarez, and J. R. Betancort Rodríguez, ‘Experimental investigations on solar driven stand-alone membrane distillation systems for remote areas’, Desalination, vol. 248, no. 1–3, pp. 125–131, Nov. 2009.
[6] F. Banat, N. Jwaied, M. Rommel, J. Koschikowski, and M. Wieghaus, ‘Desalination by a “compact SMADES” autonomous solarpowered membrane distillation unit’, Desalination, vol. 217, no. 1–3, pp. 29–37, Nov. 2007.
[7] J. Koschikowski, M. Wieghaus, and M. Rommel, ‘Solar thermal-driven desalination plants based on membrane distillation’, Desalination, vol. 156, no. 1–3, pp. 295–304, Aug. 2003.
[8] A. Ruiz-Aguirre, J. A. Andrés-Mañas, J. M. Fernández-Sevilla, and G. Zaragoza, ‘Modeling and optimization of a commercial permeate gap spiral wound membrane distillation module for seawater desalination’, Desalination, vol. 419, pp. 160–168, Oct. 2017.
[9] D. Winter, J. Koschikowski, and M. Wieghaus, ‘Desalination using membrane distillation: Experimental studies on full scale spiral wound modules’, J. Membr. Sci., vol. 375, no. 1–2, pp. 104–112, Jun. 2011.
[10] D. Winter, J. Koschikowski, and S. Ripperger, ‘Desalination using membrane distillation: Flux enhancement by feed water deaeration on spiral-wound modules’, J. Membr. Sci., vol. 423–424, pp. 215–224, Dec. 2012.
[12] P. A. Hogan, Sudjito, A. G. Fane, and G. L. Morrison, ‘Desalination by solar heated membrane distillation’, Desalination, vol. 81, no. 1–3, pp. 81–90, Jul. 1991.
[14] J. Pátek, J. Hrubý, J. Klomfar, M. Součková, and A. H. Harvey, ‘Reference Correlations for Thermophysical Properties of Liquid Water at 0.1MPa’, J. Phys. Chem. Ref. Data, vol. 38, no. 1, pp. 21–29, Mar. 2009.
[15] K. G. Nayar, M. H. Sharqawy, L. D. Banchik, and J. H. Lienhard V, ‘Thermophysical properties of seawater: A review and new correlations that include pressure dependence’, Desalination, vol. 390, pp. 1–24, Jul. 2016.
[16] C. O. Popiel and J. Wojtkowiak, ‘Simple Formulas for Thermophysical Properties of Liquid Water for Heat Transfer Calculations (from 0°C to 150°C)’, Heat Transf. Eng., vol. 19, no. 3, pp. 87–101, Jan. 1998.
[18] J. Swaminathan, H. W. Chung, D. M. Warsinger, and J. H. Lienhard V, ‘Membrane distillation model based on heat exchanger theory and configuration comparison’, Appl. Energy, vol. 184, pp. 491–505, Dec. 2016.
55
[19] A. Chorak, P. Palenzuela, D.-C. Alarcón-Padilla, and A. Ben Abdellah, ‘Experimental characterization of a multi-effect distillation system coupled to a flat plate solar collector field: Empirical correlations’, Appl. Therm. Eng., vol. 120, pp. 298–313, Jun. 2017.
[21] S. Fischer, W. Heidemann, H. Müller-Steinhagen, B. Perers, P. Bergquist, and B. Hellström,
‘Collector test method under quasi-dynamic conditions according to the European Standard EN
12975-2’, Sol. Energy, vol. 76, no. 1–3, pp. 117–123, Jan. 2004.
Conference Paper
[11] C. Bier and U. Plantikow, ‘Solar powered desalination by membrane distillation’, in IDA WORLD CONGRESS ON DESALINATION AND WATER SCIENCES, Abu Dhabi, 1995, pp. 397–410.
Report
[1] ‘Renewable Energy in the Water, Energy & Food Nexus’, IRENA, 2015.
[2] E. Hameeteman, ‘Future Water (In)Security: Facts, Figures, and Predictions’, Global Water Institute, 2013.
Web document
[4] ‘Desalination industry enjoys growth spurt as scarcity starts to bite’, Global Water Intelligence. [Online]. Available: https://www.globalwaterintel.com/desalination-industry-enjoys-growth-spurt-scarcity-starts-bite/. [Accessed: 13-May-2018].
Figures reused
Figure 1: "Reprinted from Desalination, Vol 248 Issue 1-3, J. Koschikowski, M. Wieghaus, M.
Rommel, Vicente Subiela Ortin, Baltasar Peñate Suarez, Juana Rosa Betancort Rodríguez,
Experimental investigations on solar driven stand-alone membrane distillation systems for
remote areas, 125-131, 2009, with permission from Elsevier"
Figure 2: "Reprinted from Journal of Membrane Science, Vol 423, D. Winter, J. Koschikowski,
S. Ripperger, Desalination using membrane distillation: Flux enhancement by feed water
deaeration on spiral-wound modules, 215-224, 2012, with permission from Elsevier"
"Reprinted from Journal of Membrane Science, Vol 375/Issue 1-2, D. Winter, J. Koschikowski,
M. Wieghaus, Desalination using membrane distillation: Experimental studies on full scale spiral
wound modules, 104-112, 2011, with permission from Elsevier"
Figure 3: "Reprinted from Journal of Membrane Science, Vol 375/Issue 1-2, D. Winter, J.
Koschikowski, M. Wieghaus, Desalination using membrane distillation: Experimental studies on
full scale spiral wound modules, 104-112, 2011, with permission from Elsevier"
56
7. Appendices
7.1 Appendix A
7.1.1 Technical details of experimental setup and its components
1. Solar collector field
The solar collector field consisted of four LBM 10 HTF manufactured by Wagner and Co.
based in Madrid, Spain. Below is attached some technical data on the flat plate collector and a
picture of the collector field itself.
57
2. Permeate Gap Membrane Distillation Module
The technical details of the permeate gap distillation module, as provided by the
manufacturer, are:
Membrane Contactor module LS6.707.4 (stainless steel distillate spacer)
Configuration: LGMD (liquid gap MD)
Membrane area: 5.15 m2
Channel length: 6.3 m; Distillate channel spacer: stainless steel 316 mesh, 0.35 mm thickness
Channel widths 415 mm; Feed spacer: 2.85 mm; Membrane channel spacer: 2.85 mm
3. Tank loop
Tank volume = 1.5 m3
Direct no heat exchanger type tank.
Working fluid : Water at 2 bar pressure
Number of nodes = 4
7.1.2 Images/Pictures of experimental setup
Figure 29: Solar collector field (tank in distance)
58
Figure 30: Solar and tank loops
59
7.2 Appendix B
Table 9: Experiment input parameters with dispersion and standard deviations for all experiment runs
𝑇𝑐𝑜𝑛𝑑𝑖𝑛 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 �̇�𝐹 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 �̇�𝐹
°C °C l/h Mean Max Min 𝜎 Mean Max Min 𝜎 Mean Max Min 𝜎
20 60 200 19.71 20.05 19.26 0.16 59.97 60.74 59.04 0.32 199.71 207.64 190.80 2.57
20 60 300 19.82 20.30 19.26 0.26 60.01 60.65 59.35 0.22 301.64 312.04 296.78 2.09
20 60 400 21.03 21.70 20.25 0.43 60.05 61.06 59.04 0.29 398.51 418.73 392.33 3.08
20 70 200 19.85 19.97 19.73 0.06 70.00 70.55 69.55 0.17 192.89 205.20 183.68 4.52
20 70 300 19.96 20.26 19.65 0.13 70.08 70.35 69.74 0.09 297.00 308.44 256.24 5.16
20 70 400 20.04 20.76 19.16 0.30 69.84 70.67 68.83 0.44 400.99 414.53 392.44 3.00
20 70 500 20.31 22.15 18.06 1.20 70.16 70.73 69.63 0.23 500.35 507.15 496.73 2.11
20 80 200 20.12 20.56 19.55 0.22 80.06 80.55 79.65 0.19 199.22 203.36 194.63 1.47
20 80 300 19.92 20.16 19.75 0.09 79.84 80.64 79.04 0.23 297.00 313.99 283.69 5.73
20 80 400 20.71 21.05 20.55 0.09 80.07 80.56 79.52 0.18 397.06 401.44 393.53 1.13
25 60 200 24.77 25.17 24.26 0.26 59.71 60.24 58.95 0.26 197.75 210.68 189.83 4.01
25 60 300 25.07 25.20 24.67 0.10 60.20 60.64 59.51 0.18 302.24 313.50 283.28 3.68
25 60 400 25.01 25.27 24.66 0.13 60.06 60.64 59.54 0.18 398.02 407.55 389.33 3.89
25 60 500 25.01 25.47 24.46 0.23 60.10 60.74 59.34 0.28 498.61 504.90 492.56 2.29
25 70 200 24.86 25.37 24.45 0.26 69.88 70.34 69.53 0.18 196.21 208.46 189.75 3.58
25 70 300 24.99 25.18 24.75 0.07 70.09 71.00 69.20 0.39 299.47 308.14 294.56 2.18
25 70 400 25.30 25.90 24.75 0.25 69.86 70.57 69.23 0.24 397.41 407.89 389.63 3.28
25 70 500 25.67 26.66 24.67 0.49 69.63 70.54 68.24 0.57 499.65 507.34 493.31 2.30
25 80 200 25.04 25.57 24.64 0.24 79.96 80.45 79.45 0.19 197.25 209.36 189.04 3.74
25 80 300 24.74 24.97 24.46 0.11 80.08 81.05 79.34 0.35 299.84 313.80 287.29 6.21
25 80 400 25.11 25.67 24.26 0.26 79.55 80.27 78.36 0.43 396.49 403.46 392.33 2.05
30 60 200 30.13 30.45 29.74 0.17 59.89 60.15 59.56 0.09 198.85 204.38 195.71 1.30
30 60 300 29.98 30.75 29.55 0.22 60.21 60.74 59.66 0.20 297.98 302.48 284.40 3.02
30 60 400 30.03 30.65 29.55 0.23 60.33 61.35 59.36 0.41 401.55 409.24 380.96 4.19
30 70 200 30.00 30.55 29.53 0.29 70.10 70.44 69.75 0.11 197.49 202.35 193.91 1.35
30 70 300 30.04 30.35 29.55 0.16 69.88 70.31 69.33 0.20 299.24 307.35 295.61 1.89
30 70 400 30.01 30.35 29.45 0.20 70.05 70.64 69.64 0.13 396.75 402.08 392.06 1.63
30 80 200 29.96 30.65 29.54 0.25 80.10 80.55 79.45 0.16 197.10 207.71 185.81 2.55
30 80 300 30.07 30.35 29.84 0.12 79.93 81.35 78.95 0.27 297.87 303.23 292.43 2.40
30 80 400 29.95 30.35 29.55 0.15 80.09 80.35 79.84 0.08 399.16 407.59 393.94 1.84
60
7.3 Appendix C
Table 10: Date and time of experiment runs
𝑇𝑐𝑜𝑛𝑑𝑖𝑛 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 �̇�𝐹 Date Time
°C °C l/h All in 2018
20 60 200 26/02 13:23-14:23
20 60 300 08/03 13:59-14:59
20 60 400 09/03 9:30-10:30
20 70 200 06/04 11:05-11:50
20 70 300 06/04 15:26-16:11
20 70 400 12/03 14:17-15:02
20 70 500 13/03 14:05-14:50
20 80 200 16/04 15:22-16:07
20 80 300 04/04 15:26-16:11
20 80 400 11/04 15:06-15:51
25 60 200 14/03 14:20-15:05
25 60 300 05/04 11:16-12:01
25 60 400 16/03 13:08-13:53
25 60 500 14/3 12:15-13:00
25 70 200 16/03 15:20-16:05
25 70 300 20/03 11:26-12:11
25 70 400 21/03 12:15-13:00
25 70 500 19/03 12:22-13:07
25 80 200 21/03 15:33-16:18
25 80 300 05/04 15:25-16:10
25 80 400 13/04 15:04-15:49
30 60 200 23/05 12:45-13:30
30 60 300 12/04 12:15-13:00
30 60 400 10/04 12:00-12:45
30 70 200 22/05 15:25-16:10
30 70 300 12/04 15:23-16:07
30 70 400 18/04 12:30-13:15
30 80 200 20/04 15:30-16:15
30 80 300 18/04 15:30-16:15
30 80 400 25/05 15:00-15:45
61
7.4 Appendix D
7.4.1 Derivation of uncertainty/error of performance indicators
Equation 9 has been applied to the respective equations (Equation 2 for 𝑃𝑓𝑙𝑢𝑥, Equation 4
for 𝑆𝑇𝐸𝐶, Equation 6 for 𝐺𝑂𝑅 and Equation 7 for 𝜀) to determine the final reduced uncertainty
equation for each of the above performance indicator.
a) 𝑃𝑓𝑙𝑢𝑥
Recalling the expression for 𝑃𝑓𝑙𝑢𝑥;
𝑃𝑓𝑙𝑢𝑥 =�̇�𝑝
𝜌𝑝 ⋅ 𝐴𝑀
Equation 2
Where �̇�𝑝 and 𝜌𝑝 are measured and derived variables respectively and 𝐴𝑀 is constant.
Applying Equation 9 to the Equation 2;
∆𝑃𝑓𝑙𝑢𝑥 = √(𝜕𝑃𝑓𝑙𝑢𝑥
𝜕�̇�𝑝⋅ ∆�̇�𝑝)
2
+ (𝜕𝑃𝑓𝑙𝑢𝑥
𝜕𝜌𝑝⋅ ∆𝜌𝑝)
2
= √(1
𝜌𝑝 ⋅ 𝐴𝑀⋅ ∆�̇�𝑝)
2
+ (−�̇�𝑝
𝜌𝑝2 ⋅ 𝐴𝑀⋅ ∆𝜌𝑝)
2
=1
𝐴𝑀⋅ √(
∆�̇�𝑝
𝜌𝑝)
2
+ (−�̇�𝑝 ⋅ ∆𝜌𝑝
𝜌𝑝2)
2
b) 𝑆𝑇𝐸𝐶
Recalling the expression for 𝑆𝑇𝐸𝐶;
𝑆𝑇𝐸𝐶 =�̇�𝐹 ⋅ 𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ 𝜌𝑝 ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡)
�̇�𝑃 Equation 4
Where �̇�𝐹, 𝑇𝑒𝑣𝑎𝑝𝑖𝑛, 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡 and �̇�𝑝 are measured variables and 𝜌𝐹, 𝐶𝑝𝐹 and 𝜌𝑝 are
derived variables. Applying Equation 9 to the Equation 4;
∆𝑆𝑇𝐸𝐶 =
√
(𝜕𝑆𝑇𝐸𝐶
𝜕�̇�𝐹⋅ ∆�̇�𝐹)
2
+ (𝜕𝑆𝑇𝐸𝐶
𝜕𝜌𝐹⋅ ∆𝜌𝐹)
2
+ (𝜕𝑆𝑇𝐸𝐶
𝜕𝐶𝑝𝐹⋅ ∆𝐶𝑝𝐹)
2
+ (𝜕𝑆𝑇𝐸𝐶
𝜕𝜌𝑝⋅ ∆𝜌𝑝)
2
+(𝜕𝑆𝑇𝐸𝐶
𝜕𝑇𝑒𝑣𝑎𝑝𝑖𝑛⋅ ∆𝑇𝑒𝑣𝑎𝑝𝑖𝑛)
2
+ (𝜕𝑆𝑇𝐸𝐶
𝜕𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡⋅ ∆𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡)
2
+ (𝜕𝑆𝑇𝐸𝐶
𝜕�̇�𝑃⋅ ∆�̇�𝑃)
2
62
=
√
(𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ 𝜌𝑝 ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡)
�̇�𝑃⋅ ∆�̇�𝐹)
2
+(�̇�𝐹 ⋅ 𝐶𝑝𝐹 ⋅ 𝜌𝑝 ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡)
�̇�𝑃⋅ ∆𝜌𝐹)
2
+ (�̇�𝐹 ⋅ 𝜌𝐹 ⋅ 𝜌𝑝 ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡)
�̇�𝑃⋅ ∆𝐶𝑝𝐹)
2
+(�̇�𝐹 ⋅ 𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡)
�̇�𝑃⋅ ∆𝜌𝑝)
2
+ (�̇�𝐹 ⋅ 𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ 𝜌𝑝
�̇�𝑃⋅ ∆𝑇𝑒𝑣𝑎𝑝𝑖𝑛)
2
+(−�̇�𝐹 ⋅ 𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ 𝜌𝑝
�̇�𝑃⋅ ∆𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡)
2
+ (−�̇�𝐹 ⋅ 𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ 𝜌𝑝 ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡)
�̇�𝑃2 ⋅ ∆�̇�𝑃)
2
c) 𝐺𝑂𝑅
Recalling the expression for 𝐺𝑂𝑅;
𝐺𝑂𝑅 =�̇�𝑝 ⋅ 𝛥ℎ𝑣
�̇�𝐹 ⋅ 𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡) Equation 6
Where �̇�𝑝, �̇�𝐹, 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 and 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡 are measured variables and 𝛥ℎ𝑣 , 𝜌𝐹 and 𝐶𝑝𝐹 are
derived variables. Applying Equation 9 to Equation 6;
∆𝐺𝑂𝑅 =
√
(𝜕𝐺𝑂𝑅
𝜕�̇�𝑝⋅ ∆�̇�𝑝)
2
+ (𝜕𝐺𝑂𝑅
𝜕(𝛥ℎ𝑣)⋅ ∆(𝛥ℎ𝑣))
2
+ (𝜕𝐺𝑂𝑅
𝜕�̇�𝐹⋅ ∆�̇�𝐹)
2
+ (𝜕𝐺𝑂𝑅
𝜕𝜌𝐹⋅ ∆𝜌𝐹)
2
+(𝜕𝐺𝑂𝑅
𝜕𝐶𝑝𝐹⋅ ∆𝐶𝑝𝐹)
2
+ (𝜕𝐺𝑂𝑅
𝜕𝑇𝑒𝑣𝑎𝑝𝑖𝑛⋅ ∆𝑇𝑒𝑣𝑎𝑝𝑖𝑛)
2
+ (𝜕𝐺𝑂𝑅
𝜕𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡⋅ ∆𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡)
2
=
√
(𝛥ℎ𝑣
�̇�𝐹 ⋅ 𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡)⋅ ∆�̇�𝑝)
2
+ (𝛥ℎ𝑣
�̇�𝐹 ⋅ 𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡)⋅ ∆(𝛥ℎ𝑣))
2
+(−�̇�𝑝 ⋅ 𝛥ℎ𝑣
�̇�𝐹2 ⋅ 𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡)
⋅ ∆�̇�𝐹)
2
+ (−�̇�𝑝 ⋅ 𝛥ℎ𝑣
�̇�𝐹 ⋅ 𝜌𝐹2 ⋅ 𝐶𝑝𝐹 ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡)
⋅ ∆𝜌𝐹)
2
+
(−�̇�𝑝 ⋅ 𝛥ℎ𝑣
�̇�𝐹 ⋅ 𝜌𝐹 ⋅ 𝐶𝑝𝐹2 ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡)
⋅ ∆𝐶𝑝𝐹)
2
+ (−�̇�𝑝 ⋅ 𝛥ℎ𝑣
�̇�𝐹 ⋅ 𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡)2 ⋅ ∆𝑇𝑒𝑣𝑎𝑝𝑖𝑛)
2
+(�̇�𝑝 ⋅ 𝛥ℎ𝑣
�̇�𝐹 ⋅ 𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡)2 ⋅ ∆𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡)
2
63
d) 𝜀
Recalling the expression for 𝜀;
𝜀 =𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛
Equation 7
Where 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡 , 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 and 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 are measured variables. Applying Equation 9 to
Equation 7;
∆𝜀 = √(𝜕𝜀
𝜕𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡⋅ ∆𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡)
2
+ (𝜕𝜀
𝜕𝑇𝑐𝑜𝑛𝑑𝑖𝑛⋅ ∆𝑇𝑐𝑜𝑛𝑑𝑖𝑛)
2
+ (𝜕𝜀
𝜕𝑇𝑒𝑣𝑎𝑝𝑖𝑛⋅ ∆𝑇𝑒𝑣𝑎𝑝𝑖𝑛)
2
=
√
(1
𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛⋅ ∆𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡)
2
+ (𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡 − 𝑇𝑒𝑣𝑎𝑝𝑖𝑛
(𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛)2 ⋅ ∆𝑇𝑐𝑜𝑛𝑑𝑖𝑛)
2
+(−𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛
(𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛)2 ⋅ ∆𝑇𝑒𝑣𝑎𝑝𝑖𝑛)
2
64
7.4.2 Derivation of uncertainty/error of solar collector efficiency
Equation 9 has been applied to the experimentally determined solar collector efficiency
(given by Equation 12) and the theoretically determined efficiency (given by Equation 10) to
calculate the uncertainty/error of the above two parameters.
a) Experimental 𝜂𝑠𝑜𝑙𝑎𝑟
Recalling the expression for 𝜂𝑠𝑜𝑙𝑎𝑟 ;
𝜂𝑠𝑜𝑙𝑎𝑟𝑒𝑥𝑝 = �̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐶𝑝𝑐𝑜𝑙 ⋅ (𝑇𝑠𝑜𝑙𝑎𝑟𝑜𝑢𝑡 − 𝑇𝑠𝑜𝑙𝑎𝑟𝑖𝑛)
𝐴𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐺𝑇 Equation 12
This needs to be rewritten in terms of the measured variables as;
𝜂𝑠𝑜𝑙𝑎𝑟𝑒𝑥𝑝 = �̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝜌𝑐𝑜𝑙 ⋅ 𝐶𝑝𝑐𝑜𝑙 ⋅ (𝑇𝑠𝑜𝑙𝑎𝑟𝑜𝑢𝑡 − 𝑇𝑠𝑜𝑙𝑎𝑟𝑖𝑛)
𝐴𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐺𝑇
Where �̇�𝑠𝑜𝑙𝑎𝑟 is the volumetric flow rate in the solar loop [l/s]
𝜌𝑐𝑜𝑙 is the density of the fluid at mean collector temperature [kg/l]
Here �̇�𝑠𝑜𝑙𝑎𝑟, 𝐶𝑝𝑐𝑜𝑙 , 𝑇𝑠𝑜𝑙𝑎𝑟𝑜𝑢𝑡 , 𝑇𝑠𝑜𝑙𝑎𝑟𝑖𝑛 and 𝐺𝑇 are measured variables, 𝜌𝑐𝑜𝑙 and 𝐶𝑝𝑐𝑜𝑙 are
derived variables and 𝐴𝑠𝑜𝑙𝑎𝑟 is a constant. Applying Equation 9 to this;
∆𝜂𝑠𝑜𝑙𝑎𝑟𝑒𝑥𝑝 =
√
(𝜕𝜂𝑠𝑜𝑙𝑎𝑟𝑒𝑥𝑝
𝜕�̇�𝑠𝑜𝑙𝑎𝑟⋅ ∆�̇�𝑠𝑜𝑙𝑎𝑟)
2
+ (𝜕𝜂𝑠𝑜𝑙𝑎𝑟𝑒𝑥𝑝𝜕𝜌𝑐𝑜𝑙
⋅ ∆𝜌𝑐𝑜𝑙)
2
+ (𝜕𝜂𝑠𝑜𝑙𝑎𝑟𝑒𝑥𝑝𝜕𝐶𝑝𝑐𝑜𝑙
⋅ ∆𝐶𝑝𝑐𝑜𝑙)
2
+
(𝜕𝜂𝑠𝑜𝑙𝑎𝑟𝑒𝑥𝑝𝜕𝑇𝑠𝑜𝑙𝑎𝑟𝑜𝑢𝑡
⋅ ∆𝑇𝑠𝑜𝑙𝑎𝑟𝑜𝑢𝑡)
2
+ (𝜕𝜂𝑠𝑜𝑙𝑎𝑟𝑒𝑥𝑝𝜕𝑇𝑠𝑜𝑙𝑎𝑟𝑖𝑛
⋅ ∆𝑇𝑠𝑜𝑙𝑎𝑟𝑖𝑛)
2
+ (𝜕𝜂𝑠𝑜𝑙𝑎𝑟𝑒𝑥𝑝𝜕𝐺𝑇
⋅ ∆𝐺𝑇)
2
=
√
(𝜌𝑐𝑜𝑙 ⋅ 𝐶𝑝𝑐𝑜𝑙 ⋅ (𝑇𝑠𝑜𝑙𝑎𝑟𝑜𝑢𝑡 − 𝑇𝑠𝑜𝑙𝑎𝑟𝑖𝑛)
𝐴𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐺𝑇⋅ ∆�̇�𝑠𝑜𝑙𝑎𝑟)
2
+ (�̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐶𝑝𝑐𝑜𝑙 ⋅ (𝑇𝑠𝑜𝑙𝑎𝑟𝑜𝑢𝑡 − 𝑇𝑠𝑜𝑙𝑎𝑟𝑖𝑛)
𝐴𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐺𝑇⋅ ∆𝜌𝑐𝑜𝑙)
2
+(�̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝜌𝑐𝑜𝑙 ⋅ (𝑇𝑠𝑜𝑙𝑎𝑟𝑜𝑢𝑡 − 𝑇𝑠𝑜𝑙𝑎𝑟𝑖𝑛)
𝐴𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐺𝑇⋅ ∆𝐶𝑝𝑐𝑜𝑙)
2
+ (�̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝜌𝑐𝑜𝑙 ⋅ 𝐶𝑝𝑐𝑜𝑙
𝐴𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐺𝑇⋅ ∆𝑇𝑠𝑜𝑙𝑎𝑟𝑜𝑢𝑡)
2
+(�̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝜌𝑐𝑜𝑙 ⋅ 𝐶𝑝𝑐𝑜𝑙
𝐴𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐺𝑇⋅ ∆𝑇𝑠𝑜𝑙𝑎𝑟𝑖𝑛)
2
+ (−�̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝜌𝑐𝑜𝑙 ⋅ 𝐶𝑝𝑐𝑜𝑙 ⋅ (𝑇𝑠𝑜𝑙𝑎𝑟𝑜𝑢𝑡 − 𝑇𝑠𝑜𝑙𝑎𝑟𝑖𝑛)
𝐴𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐺𝑇2 ⋅ ∆𝐺𝑇)
2
65
=1
𝐴𝑠𝑜𝑙𝑎𝑟
√
(𝜌𝑐𝑜𝑙 ⋅ 𝐶𝑝𝑐𝑜𝑙 ⋅ (𝑇𝑠𝑜𝑙𝑎𝑟𝑜𝑢𝑡 − 𝑇𝑠𝑜𝑙𝑎𝑟𝑖𝑛)
𝐺𝑇⋅ ∆�̇�𝑠𝑜𝑙𝑎𝑟)
2
+ (�̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐶𝑝𝑐𝑜𝑙 ⋅ (𝑇𝑠𝑜𝑙𝑎𝑟𝑜𝑢𝑡 − 𝑇𝑠𝑜𝑙𝑎𝑟𝑖𝑛)
𝐺𝑇⋅ ∆𝜌𝑐𝑜𝑙)
2
+(�̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝜌𝑐𝑜𝑙 ⋅ (𝑇𝑠𝑜𝑙𝑎𝑟𝑜𝑢𝑡 − 𝑇𝑠𝑜𝑙𝑎𝑟𝑖𝑛)
𝐺𝑇⋅ ∆𝐶𝑝𝑐𝑜𝑙)
2
+ (�̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝜌𝑐𝑜𝑙 ⋅ 𝐶𝑝𝑐𝑜𝑙
𝐺𝑇⋅ ∆𝑇𝑠𝑜𝑙𝑎𝑟𝑜𝑢𝑡)
2
+(�̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝜌𝑐𝑜𝑙 ⋅ 𝐶𝑝𝑐𝑜𝑙
𝐺𝑇⋅ ∆𝑇𝑠𝑜𝑙𝑎𝑟𝑖𝑛)
2
+ (−�̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝜌𝑐𝑜𝑙 ⋅ 𝐶𝑝𝑐𝑜𝑙 ⋅ (𝑇𝑠𝑜𝑙𝑎𝑟𝑜𝑢𝑡 − 𝑇𝑠𝑜𝑙𝑎𝑟𝑖𝑛)
𝐺𝑇2 ⋅ ∆𝐺𝑇)
2
b) Theoretical efficiency
Recalling the equation for 𝜂𝑠𝑜𝑙𝑎𝑟 ;
𝜂𝑠𝑜𝑙𝑎𝑟𝑐𝑎𝑙𝑐 = 𝜂0 ⋅ 𝐾𝜏𝛼 −𝑘1𝐺𝑇
(𝑇𝑐𝑜𝑙 − 𝑇𝑎𝑚𝑏) −𝑘2𝐺𝑇
(𝑇𝑐𝑜𝑙 − 𝑇𝑎𝑚𝑏)2 Equation 10
Where 𝐺𝑇, 𝑇𝑐𝑜𝑙 and 𝑇𝑎𝑚𝑏 are measured variables, 𝐾𝜏𝛼 is a derived variable and 𝜂0, 𝑘1 and
𝑘2 are constants. Applying Equation 9 to Equation 10;
∆𝜂𝑠𝑜𝑙𝑎𝑟𝑐𝑎𝑙𝑐 =
√
(𝜕𝜂𝑠𝑜𝑙𝑎𝑟𝑐𝑎𝑙𝑐𝜕𝐾𝜏𝛼
⋅ ∆𝐾𝜏𝛼)
2
+ (𝜕𝜂𝑠𝑜𝑙𝑎𝑟𝑐𝑎𝑙𝑐𝜕𝐺𝑇
⋅ ∆𝐺𝑇)
2
+ (𝜕𝜂𝑠𝑜𝑙𝑎𝑟𝑐𝑎𝑙𝑐𝜕𝑇𝑐𝑜𝑙
⋅ ∆𝑇𝑐𝑜𝑙)
2
+(𝜕𝜂𝑠𝑜𝑙𝑎𝑟𝑐𝑎𝑙𝑐𝜕𝑇𝑎𝑚𝑏
⋅ ∆𝑇𝑎𝑚𝑏)
2
=
√
(𝜂0 ⋅ ∆𝐾𝜏𝛼)2 + ((𝑘1
𝐺𝑇2(𝑇𝑐𝑜𝑙 − 𝑇𝑎𝑚𝑏) +
𝑘2
𝐺𝑇2(𝑇𝑐𝑜𝑙 − 𝑇𝑎𝑚𝑏)2) ⋅ ∆𝐺𝑇)
2
+( (−𝑘1𝐺𝑇
+ 2 ⋅𝑘2𝐺𝑇
(𝑇𝑐𝑜𝑙 − 𝑇𝑎𝑚𝑏)) ⋅ ∆𝑇𝑐𝑜𝑙)
2
+((𝑘1𝐺𝑇
+ 2 ⋅𝑘2𝐺𝑇
(𝑇𝑐𝑜𝑙 − 𝑇𝑎𝑚𝑏)) ⋅ ∆𝑇𝑎𝑚𝑏)
2
66
7.4.3 Derivation of uncertainty/error of heat required for MD
The heat required by the PGMD module was calculated using the model and then validated
against the experimentally determined values for the same operating conditions. Equation 16 and
Equation 17 was used to determine the heat required for the experimentally and theoretically
determined 𝑄𝐻𝑋2 respectively;
a) Experimental 𝑄𝐻𝑋2
Recalling the expression (Equation 16) for 𝑄𝐻𝑋2;
𝑄𝐻𝑋2 = �̇�𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡) Equation 16
Which, when expressed in terms of measured variables, becomes;
𝑄𝐻𝑋2 = �̇�𝐹 ⋅ 𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡)
Where �̇�𝐹, 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 and 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡 are measured variables in the case of the experimental 𝑄𝐻𝑋2 and
𝜌𝐹 and 𝐶𝑝𝐹 are derived variables. Applying Equation 9 to the above equation;
∆𝑄𝐻𝑋2 =
√
(𝜕𝑄𝐻𝑋2
𝜕�̇�𝐹⋅ ∆�̇�𝐹)
2
+ (𝜕𝑄𝐻𝑋2𝜕𝜌𝐹
⋅ ∆𝜌𝐹)2
+ (𝜕𝑄𝐻𝑋2𝜕𝐶𝑝𝐹
⋅ ∆𝐶𝑝𝐹)
2
+(𝜕𝑄𝐻𝑋2𝜕𝑇𝑒𝑣𝑎𝑝𝑖𝑛
⋅ ∆𝑇𝑒𝑣𝑎𝑝𝑖𝑛)
2
+ (𝜕𝑄𝐻𝑋2𝜕𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡
⋅ ∆𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡)
2
= √(𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡) ⋅ ∆�̇�𝐹)
2+ (�̇�𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡) ⋅ ∆𝜌𝐹)
2 +
(�̇�𝐹 ⋅ 𝜌𝐹 ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡) ⋅ ∆𝐶𝑝𝐹)2+ (�̇�𝐹 ⋅ 𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ ∆𝑇𝑒𝑣𝑎𝑝𝑖𝑛)
2+ (−�̇�𝐹 ⋅ 𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ ∆𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡)
2
b) Theoretical 𝑄𝐻𝑋2
Recalling the expression for 𝑄𝐻𝑋2 in terms of 𝜀 (Equation 17) gives;
𝑄𝐻𝑋2 = �̇�𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (1 − 𝜀) ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛) Equation 28
Which, when expressed in terms of set operating variables, becomes;
𝑄𝐻𝑋2 = �̇�𝐹 ⋅ 𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (1 − 𝜀) ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛)
The set operating variables �̇�𝐹, 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 and 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 do not have any uncertainty as they are
assumed input parameters in the theoretical model. The 𝜀 may be determined using Equation 21
67
but as it is also a function of the input variables, it’s uncertainty is only due to error in the
statistical model i.e the root mean square error.
Applying Equation 9 to the above equation yields;
∆𝑄𝐻𝑋2 = √+(𝜕𝑄𝐻𝑋2𝜕𝜌𝐹
⋅ ∆𝜌𝐹)2
+ (𝜕𝑄𝐻𝑋2𝜕𝐶𝑝𝐹
⋅ ∆𝐶𝑝𝐹)
2
+ (𝜕𝑄𝐻𝑋2𝜕𝜀
⋅ ∆𝜀)2
= √(�̇�𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (1 − 𝜀) ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛) ⋅ ∆𝜌𝐹)
2
+ (�̇�𝐹 ⋅ 𝜌𝐹 ⋅ (1 − 𝜀) ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛) ⋅ ∆𝐶𝑝𝐹)2+ (− �̇�𝐹 ⋅ 𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛) ⋅ ∆𝜀)
2
68
7.5 Appendix E
Table 11: Variation of UAHX2 at different operating conditions
𝑇𝑐𝑜𝑛𝑑𝑖𝑛 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 �̇�𝐹 𝑈𝐴𝐻𝑋2
°C °C l/h W/°C
20 60 200 113.002
20 60 300 132.998
20 60 400 212.567
20 70 200 161.103
20 70 300 191.150
20 70 400 292.808
20 70 500 352.705
20 80 200 130.786
20 80 300 245.233
20 80 400 305.276
25 60 200 83.826
25 60 300 142.506
25 60 400 158.756
25 60 500 279.750
25 70 200 98.507
25 70 300 213.826
25 70 400 206.049
25 70 500 430.083
25 80 200 123.670
25 80 300 209.118
25 80 400 345.054
30 60 200 67.566
30 60 300 122.669
30 60 400 175.005
30 70 200 82.156
30 70 300 220.754
30 70 400 214.614
30 80 200 129.388
30 80 300 191.276
30 80 400 272.508
69
7.6 Appendix F
7.6.1 Derivation of Minimum Radiation required for MD operation
For any MD operation, the three defined input parameters are the �̇�𝐹, 𝑇𝑒𝑣𝑎𝑝𝑖𝑛 and 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 .
Starting from the MD loop, we know that the heat required for MD operation (as in Equation
17) is;
𝑄𝐻𝑋 = �̇�𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (1 − 𝜀) ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛)
= �̇�𝐹 ⋅ 𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (1 − 𝜀) ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛)
This heat is provided, via the heat exchanger, from the solar loop. Hence, ignoring heat losses,
the same heat is transferred from the solar loop and can be expressed (Equation 14) as;
𝑄𝐻𝑋 = �̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐶𝑝𝐻𝑋𝑠𝑜𝑙𝑎𝑟 ⋅ (𝑇𝐻𝑋𝑖𝑛𝑠𝑜𝑙𝑎𝑟 − 𝑇𝐻𝑋𝑜𝑢𝑡𝑠𝑜𝑙𝑎𝑟)
Assuming matched flow across the heat exchanger i.e (�̇�𝑠𝑜𝑙𝑎𝑟 = �̇�𝐹), the �̇�𝑠𝑜𝑙𝑎𝑟 can be
calculated. Rearranging the above equation;
𝑇𝐻𝑋𝑖𝑛𝑠𝑜𝑙𝑎𝑟 − 𝑇𝐻𝑋𝑜𝑢𝑡𝑠𝑜𝑙𝑎𝑟 =𝑄𝐻𝑋
�̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐶𝑝𝐻𝑋𝑠𝑜𝑙𝑎𝑟
Assuming that from the outlet of the solar collector field to the inlet of the heat exchanger, there
is a temperature drop of 1.2 °C. This value is chosen based on field experience and can be said to
deviate from this value by, at most, 0.5 °C.
Between the heat exchanger outlet and the solar collector field inlet there is a small heat loss.
However this heat loss to the ambient is neglected as it is largely compensated for by the heat of
compression which is added to the fluid by the pump. The error associated with this assumption
is taken, by experience, as 0.3 °C.
Hence the above equation can be rewritten as;
𝑇𝑠𝑜𝑙𝑎𝑟𝑜𝑢𝑡 − 𝑇𝑠𝑜𝑙𝑎𝑟𝑖𝑛 =𝑄𝐻𝑋
�̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐶𝑝𝐻𝑋𝑠𝑜𝑙𝑎𝑟− 1.2
Recalling Equation 12, the efficiency of the solar collector field can be expressed as;
𝜂𝑠𝑜𝑙𝑎𝑟 =�̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐶𝑝𝑐𝑜𝑙 ⋅ (𝑇𝑠𝑜𝑙𝑎𝑟𝑜𝑢𝑡 − 𝑇𝑠𝑜𝑙𝑎𝑟𝑖𝑛)
𝐴𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐺𝑇
The solar collector efficiency is also given by Equation 10 as;
70
𝜂𝑠𝑜𝑙𝑎𝑟 = 𝜂0 ⋅ 𝐾𝜏𝛼 −𝑘1𝐺𝑇
(𝑇𝑐𝑜𝑙 − 𝑇𝑎𝑚𝑏) −𝑘2𝐺𝑇
(𝑇𝑐𝑜𝑙 − 𝑇𝑎𝑚𝑏)2
In both the above expressions of 𝜂𝑠𝑜𝑙𝑎𝑟 , the average collector temperature 𝑇𝑐𝑜𝑙 is required and
may be assumed to be around 10 °C above the average heat exchanger temperature on the MD
side. Or in equation form;
𝑇𝑐𝑜𝑙 ≅𝑇𝑒𝑣𝑎𝑝𝑖𝑛 + 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡
2+ 10
This is a reasonable assumption as it provides a sufficient temperature differential to drive the
sensible heat exchange across the heat exchanger while simultaneously not being excessively high
so as to reduce the efficiency of the solar collectors due to a high operating temperature. In
practice, anywhere between 8 °C - 12 °C was used throughout the course of the experiments at
the HX2.
The ambient temperature was assumed to be 25 °C.
From the two equations of 𝜂𝑠𝑜𝑙𝑎𝑟 ;
𝜂0 ⋅ 𝐾𝜏𝛼 −𝑘1𝐺𝑇
(𝑇𝑐𝑜𝑙 − 𝑇𝑎𝑚𝑏) −𝑘2𝐺𝑇
(𝑇𝑐𝑜𝑙 − 𝑇𝑎𝑚𝑏)2 =
�̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐶𝑝𝑐𝑜𝑙 ⋅ (𝑇𝑠𝑜𝑙𝑎𝑟𝑜𝑢𝑡 − 𝑇𝑠𝑜𝑙𝑎𝑟𝑖𝑛)
𝐴𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐺𝑇
Rearranging in terms of 𝐺𝑇;
𝐺𝑇 =
�̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐶𝑝𝑐𝑜𝑙 ⋅ (𝑇𝑠𝑜𝑙𝑎𝑟𝑜𝑢𝑡 − 𝑇𝑠𝑜𝑙𝑎𝑟𝑖𝑛)𝐴𝑠𝑜𝑙𝑎𝑟
+ 𝑘1 ⋅ (𝑇𝑐𝑜𝑙 − 𝑇𝑎𝑚𝑏) + 𝑘2 ⋅ (𝑇𝑐𝑜𝑙 − 𝑇𝑎𝑚𝑏)2
𝜂0 ⋅ 𝐾𝜏𝛼
For the sake of simplicity, the incident angle modifier is assumed as 1 i.e the calculation is done
for solar noon. Hence the final reduced equation for 𝐺𝑡 becomes;
𝐺𝑇 =1
𝜂0(�̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐶𝑝𝑐𝑜𝑙 ⋅ (𝑇𝑠𝑜𝑙𝑎𝑟𝑜𝑢𝑡 − 𝑇𝑠𝑜𝑙𝑎𝑟𝑖𝑛)
𝐴𝑠𝑜𝑙𝑎𝑟+ 𝑘1 ⋅ (𝑇𝑐𝑜𝑙 − 𝑇𝑎𝑚𝑏) + 𝑘2 ⋅ (𝑇𝑐𝑜𝑙 − 𝑇𝑎𝑚𝑏)
2)
71
7.6.2 Uncertainty in calculated Minimum Radiation for MD operation
The expression for minimum radiation must first be given in terms of the modelled and derived
variables;
𝐺𝑇 =1
𝜂0
(
�̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝜌𝑐𝑜𝑙 ⋅ 𝐶𝑝𝑐𝑜𝑙 ⋅ (
�̇�𝐹 ⋅ 𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (1 − 𝜀) ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛)
�̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝜌𝑐𝑜𝑙 ⋅ 𝐶𝑝𝐻𝑋𝑠𝑜𝑙𝑎𝑟− 1.2)
𝐴𝑠𝑜𝑙𝑎𝑟+ 𝑘1
⋅ (𝑇𝑐𝑜𝑙 − 𝑇𝑎𝑚𝑏) + 𝑘2 ⋅ (𝑇𝑐𝑜𝑙 − 𝑇𝑎𝑚𝑏)2
)
As �̇�𝑠𝑜𝑙𝑎𝑟 = �̇�𝐹;
𝐺𝑇 =1
𝜂0
(
�̇�𝐹 ⋅ 𝜌𝑐𝑜𝑙 ⋅ 𝐶𝑝𝑐𝑜𝑙 ⋅ (
𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (1 − 𝜀) ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛)𝜌𝑐𝑜𝑙 ⋅ 𝐶𝑝𝐻𝑋𝑠𝑜𝑙𝑎𝑟
− 1.2)
𝐴𝑠𝑜𝑙𝑎𝑟+ 𝑘1
⋅ (𝑇𝑐𝑜𝑙 − 𝑇𝑎𝑚𝑏) + 𝑘2 ⋅ (𝑇𝑐𝑜𝑙 − 𝑇𝑎𝑚𝑏)2
)
Applying Equation 9 to the above equation to determine its uncertainty;
∆𝐺𝑇 =
√
(𝜕𝐺𝑇𝜕𝜌𝑐𝑜𝑙
∆𝜌𝑐𝑜𝑙)2
+ (𝜕𝐺𝑇𝜕𝐶𝑝𝑐𝑜𝑙
∆𝐶𝑝𝑐𝑜𝑙)
2
+ (𝜕𝐺𝑇𝜕𝜌𝐹
∆𝜌𝐹)2
+ (𝜕𝐺𝑇𝜕𝐶𝑝𝐹
∆𝐶𝑝𝐹)
2
+(𝜕𝐺𝑇𝜕𝜀
∆𝜀)2
+ (𝜕𝐺𝑇
𝜕𝐶𝑝𝐻𝑋𝑠𝑜𝑙𝑎𝑟∆𝐶𝑝𝐻𝑋𝑠𝑜𝑙𝑎𝑟)
2
72
=1
𝜂0
√
(− 1.2 ⋅ �̇�𝐹 ⋅ 𝐶𝑝𝑐𝑜𝑙
𝐴𝑠𝑜𝑙𝑎𝑟⋅ ∆𝜌𝑐𝑜𝑙)
2
+
(
�̇�𝐹 ⋅ 𝜌𝑐𝑜𝑙 ⋅ (
𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (1 − 𝜀) ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛)𝜌𝑐𝑜𝑙 ⋅ 𝐶𝑝𝐻𝑋𝑠𝑜𝑙𝑎𝑟
− 1.2)
𝐴𝑠𝑜𝑙𝑎𝑟⋅ ∆𝐶𝑝𝑐𝑜𝑙
)
2
+(�̇�𝐹 ⋅ 𝐶𝑝𝑐𝑜𝑙 ⋅ 𝐶𝑝𝐹 ⋅ (1 − 𝜀) ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛)
𝐴𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐶𝑝𝐻𝑋𝑠𝑜𝑙𝑎𝑟⋅ ∆𝜌𝐹)
2
+(�̇�𝐹 ⋅ 𝐶𝑝𝑐𝑜𝑙 ⋅ 𝜌𝐹 ⋅ (1 − 𝜀) ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛)
𝐴𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐶𝑝𝐻𝑋𝑠𝑜𝑙𝑎𝑟⋅ ∆𝐶𝑝𝐹)
2
+(−�̇�𝐹 ⋅ 𝐶𝑝𝑐𝑜𝑙 ⋅ 𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛)
𝐴𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐶𝑝𝐻𝑋𝑠𝑜𝑙𝑎𝑟⋅ ∆𝜀)
2
+(−�̇�𝐹 ⋅ 𝐶𝑝𝑐𝑜𝑙 ⋅ 𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (1 − 𝜀) ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛)
𝐴𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐶𝑝𝐻𝑋𝑠𝑜𝑙𝑎𝑟2
⋅ ∆𝐶𝑝𝐻𝑋𝑠𝑜𝑙𝑎𝑟)
2
7.6.3 Derivation of Auxiliary cooling required for steady state operation
As in the case for the derivation of the minimum radiation required for MD operation, the
calculation must start at the MD loop within which lie the defined input parameters �̇�𝐹, 𝑇𝑒𝑣𝑎𝑝𝑖𝑛
and 𝑇𝑐𝑜𝑛𝑑𝑖𝑛 . The heat required for MD operation (as in Equation 17) is;
𝑄𝐻𝑋 = �̇�𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (1 − 𝜀) ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛)
= �̇�𝐹 ⋅ 𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (1 − 𝜀) ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛)
This heat is provided, via the heat exchanger, from the solar loop. Hence, ignoring heat losses,
the same heat is transferred from the solar loop and can be expressed (Equation 14) as;
𝑄𝐻𝑋 = �̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐶𝑝𝐻𝑋𝑠𝑜𝑙𝑎𝑟 ⋅ (𝑇𝐻𝑋𝑖𝑛𝑠𝑜𝑙𝑎𝑟 − 𝑇𝐻𝑋𝑜𝑢𝑡𝑠𝑜𝑙𝑎𝑟)
Assuming matched flow across the heat exchanger i.e (�̇�𝑠𝑜𝑙𝑎𝑟 = �̇�𝐹), the �̇�𝑠𝑜𝑙𝑎𝑟 can be
calculated. Rearranging the above equation;
𝑇𝐻𝑋𝑖𝑛𝑠𝑜𝑙𝑎𝑟 − 𝑇𝐻𝑋𝑜𝑢𝑡𝑠𝑜𝑙𝑎𝑟 =𝑄𝐻𝑋
�̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐶𝑝𝐻𝑋𝑠𝑜𝑙𝑎𝑟
73
Assuming that from the outlet of the solar collector field to the inlet of the heat exchanger, there
is a temperature drop of 1.2 °C. This value is chosen based on field experience and can be said to
deviate from this value by, at most, 0.5 °C.
Between the heat exchanger outlet and the solar collector field inlet there is a small heat loss.
However this heat loss to the ambient is neglected as it is largely compensated for by the heat of
compression which is added to the fluid by the pump. The error associated with this assumption
is taken, by experience, as 0.3 °C.
Hence the above equation can be rewritten as;
𝑇𝑠𝑜𝑙𝑎𝑟𝑜𝑢𝑡 − 𝑇𝑠𝑜𝑙𝑎𝑟𝑖𝑛 =𝑄𝐻𝑋
�̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐶𝑝𝐻𝑋𝑠𝑜𝑙𝑎𝑟− 1.2
The solar collector efficiency is also given by Equation 10 as;
𝜂𝑠𝑜𝑙𝑎𝑟 = 𝜂0 ⋅ 𝐾𝜏𝛼 −𝑘1𝐺𝑇
(𝑇𝑐𝑜𝑙 − 𝑇𝑎𝑚𝑏) −𝑘2𝐺𝑇
(𝑇𝑐𝑜𝑙 − 𝑇𝑎𝑚𝑏)2
Here the ambient temperature is assumed to be 25 °C, the global titled radiation is assumed as
700 W/m2 and the incidence angle modifier is taken as unity for simplification. The average
collector temperature may be assumed to be around 10 °C above the average heat exchanger
temperature on the MD side. Or in equation form;
𝑇𝑐𝑜𝑙 ≅𝑇𝑒𝑣𝑎𝑝𝑖𝑛 + 𝑇𝑐𝑜𝑛𝑑𝑜𝑢𝑡
2+ 10
This is a reasonable assumption as it provides a sufficient temperature differential to drive the
sensible heat exchange across the heat exchanger while simultaneously not being excessively high
so as to reduce the efficiency of the solar collectors due to a high operating temperature. In
practice, anywhere between 8 °C - 12 °C was used throughout the course of the experiments at
the HX2.
The heat from the solar collectors (𝑄𝑠𝑜𝑙𝑎𝑟) can be expressed as;
𝑄𝑠𝑜𝑙𝑎𝑟 = 𝜂𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐺𝑇 ⋅ 𝐴𝑠𝑜𝑙𝑎𝑟
To determine the heat losses between the outlet of the solar collector field and the heat
exchanger inlet, the solar outlet temperature as well as the heat exchanger inlet temperature must
be determined. The solar outlet temperature can be calculated as the average collector
temperature as well as the temperature difference across the collector field is known;
𝑇𝑠𝑜𝑙𝑎𝑟𝑜𝑢𝑡 =2 ⋅ 𝑇𝑐𝑜𝑙 + 𝑇𝑠𝑜𝑙𝑎𝑟𝑜𝑢𝑡 − 𝑇𝑠𝑜𝑙𝑎𝑟𝑖𝑛
2
As mentioned before, the fluid is assumed to lose 1.2 °C to the environment and hence the heat
loss (Equation 18) may be given as;
𝑄𝑙𝑜𝑠𝑠 = 1.2 ⋅ �̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐶𝑝𝑆𝐹
74
By the first law of thermodynamics, i.e the law of conservation of energy, the heat into the
system must be balanced by the heat leaving it and hence the auxiliary cooling required may be
expressed as;
𝑄𝑐𝑜𝑜𝑙𝑒𝑟 = 𝑄𝑠𝑜𝑙𝑎𝑟 − 𝑄𝐻𝑋 − 𝑄𝑙𝑜𝑠𝑠
= 𝜂𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐺𝑇 ⋅ 𝐴𝑠𝑜𝑙𝑎𝑟 − �̇�𝐹 ⋅ 𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (1 − 𝜀) ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛) − 1.2 ⋅ �̇�𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐶𝑝𝑆𝐹
7.6.4 Uncertainty in calculated Auxiliary Cooling required for steady state
Rewriting the previously derived equation for auxiliary cooling in terms of modelled and
derived variables;
𝑄𝑐𝑜𝑜𝑙𝑒𝑟 = 𝜂𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐺𝑇 ⋅ 𝐴𝑠𝑜𝑙𝑎𝑟 − �̇�𝐹 ⋅ 𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (1 − 𝜀) ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛) − 1.2 ⋅ �̇�𝑠𝑜𝑙𝑎𝑟⋅ 𝜌𝑆𝐹 ⋅ 𝐶𝑝𝑆𝐹
Where 𝜌𝑆𝐹 is the density of propylene glycol at solar field temperature [kg/m3]
As �̇�𝑠𝑜𝑙𝑎𝑟 = �̇�𝐹;
𝑄𝑐𝑜𝑜𝑙𝑒𝑟 = 𝜂𝑠𝑜𝑙𝑎𝑟 ⋅ 𝐺𝑇 ⋅ 𝐴𝑠𝑜𝑙𝑎𝑟 − �̇�𝐹 ⋅ 𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (1 − 𝜀) ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛) − 1.2 ⋅ �̇�𝐹 ⋅ 𝜌𝑆𝐹⋅ 𝐶𝑝𝑆𝐹
Applying Equation 9 to the above equation;
∆𝑄𝑐𝑜𝑜𝑙𝑒𝑟 =
√
(𝜕𝑄𝑐𝑜𝑜𝑙𝑒𝑟𝜕𝜌𝐹
⋅ ∆𝜌𝐹)2
+ (𝜕𝑄𝑐𝑜𝑜𝑙𝑒𝑟𝜕𝐶𝑝𝐹
⋅ ∆𝐶𝑝𝐹)
2
+ (𝜕𝑄𝑐𝑜𝑜𝑙𝑒𝑟𝜕𝜀
⋅ ∆𝜀)2
+(𝜕𝑄𝑐𝑜𝑜𝑙𝑒𝑟𝜕𝜌𝑆𝐹
⋅ ∆𝜌𝑆𝐹)2
+ (𝜕𝑄𝑐𝑜𝑜𝑙𝑒𝑟𝜕𝐶𝑝𝑆𝐹
⋅ ∆𝐶𝑝𝑆𝐹)
2
= √(−�̇�𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (1 − 𝜀) ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛) ⋅ ∆𝜌𝐹)
2+ (−�̇�𝐹 ⋅ 𝜌𝐹 ⋅ (1 − 𝜀) ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛) ⋅ ∆𝐶𝑝𝐹)
2
+(�̇�𝐹 ⋅ 𝜌𝐹 ⋅ 𝐶𝑝𝐹 ⋅ (𝑇𝑒𝑣𝑎𝑝𝑖𝑛 − 𝑇𝑐𝑜𝑛𝑑𝑖𝑛) ⋅ ∆𝜀)2+ (−1.2 ⋅ �̇�𝐹 ⋅ 𝐶𝑝𝑆𝐹 ⋅ ∆𝜌𝑆𝐹)
2+ (−1.2 ⋅ �̇�𝐹 ⋅ 𝜌𝑆𝐹 ⋅ ∆𝐶𝑝𝑆𝐹)
2
75
Check-list before submitting your first draft Please go through this check-list before you submit your first draft to your supervisor. To show
that you have done it; mark the done parts by clicking on the check box☒. If the instructions in this document are not followed, your supervisor can refuse to read your thesis. You will remove the checklist from the appendix after you have received grade and the comments from the examiner.
☒ Use the given thesis template and do not change the style. Note the page breaks after each section were taken away to make the document shorter. Please add them where it is necessary. Each section should always start on a new page.
☒ Always use the spell check in the text editor before you hand in a report to avoid
misspellings. Set the language before you start writing in the document. You can use US or UK English but you must be consistent with the one style all the way through the thesis
☒ Use the check-list in [7] for the SI rules and style conventions.
☒ The Abstract should include the important parts of introduction, method, results and
conclusion with focus on method and conclusions.
☒ The Abstract should stand alone from the report, thus no references or cross-reference to figures or tables should be made.
☒ All abbreviations have to be listed in alphabetical order in the Abbreviation section and
have to be introduced the first time they are used in the text; same for the nomenclature list.
☒ Do not include a list of figures to the thesis.
☒ Does the Introduction give a good background to the research question and is it put into
perspective and do you describe why it is relevant to make this investigation?
☒ Does the Method section clearly describe the procedure of the study and performed experiments and are the main simplifications and limitations of the method discussed.
☒ Preferably the used method should be motivated in relation to the aim of the study and
other possible methods.
☒ Are the results clearly presented and easy to understand for the reader?
☒ Have you really looked at the results with critical eyes and tried to find contradictory data
and unexplainable results or trends?
☒ Have you critically evaluated the results and critically discussed simplifications and uncertainties in the method and possible implications for the results due to these imperfections?
76
☒ Have you critically evaluated the results and critically discussed simplifications and
uncertainties in the method and possible implications for the results due to these imperfections?
☒ Are your results put in relation to the results from other similar studies?
☒ Excluding or avoiding the presentation of data which does not fit what you expect is
strictly forbidden. Just if you know that there was a specific mistake in the measurement or the methodology for that particular data point, then the data could be excluded and the criteria to exclude data should be given in the Method section.
☒ Recommendation for further work should be included in the thesis.
☒ Are all figures, tables, equations, references and appendices referred to in the text? Use the Word cross-reference function.
☒ A report is usually a formal text where personal words such as “I”, “we”, “us”, “our” etc.
are seldom or never used. Therefore formulate without using these words, i.e. the passive form, e.g.: Do not write: I will investigate the effect of climate on xxxx. Instead: The effect of climate on xxxx will be investigated.
☒ Original figures (copy/paste) used from other sources should be referred in the figure text and permission needs to be requested from the author. In that case the figure text will include “[ref] with permission from (the publisher/copyright owner)” This should be only done if it is really necessary to understand the context. Otherwise avoid it.
☒ Redrawn figures used from other sources should be referred in the figure text. In that case
the figure text is “Reprinted from [ref]”.
☒ All statements and conclusions presented must be backed up with either a reference, a logical discussion, which explains the point of view or it should be concluded from your own results.
☒ If you use labels in equations or figures they must be explained the first time they appear
and then shown in a nomenclature list (with units) placed before the reference section.
☒ Use consistent terminology if you talk about the same thing: e.g. do not use once “solar radiation” and somewhere else “sunlight”.
77
Summary of your thesis for the examiner
Right from the start of this thesis work, one of the main challenges was the balance
between membrane distillation (which has little to nothing to do with solar energy by itself) and
the solar thermal part. My local supervisor at the PSA, Guillermo Zaragoza, understood this and
hence left it up to me to decide to what extent I wanted to include the solar part. Of course I
couldn’t make it a purely solar thermal thesis because that would not work for the needs of the
PSA and the company whose MD module I was testing. Mats Ronnelid, who was my supercisor
at DU, was not very knowledgeable on this topic but all three of us agreed that, to some extent,
the thesis should be a hybrid between solar thermal and membrane distillation. This is the main
reason why along with performing the characterisation of the MD module (which in my opinion
is a thesis in and of itself), I worked on developing a mathematical model to cover the whole
operation and experimental setup including the solar thermal field.
Unfortunately I did not have the time to make the mathematical model in more depth and I
would have liked to have been able to model the losses as well as the tank loop better but this
was just not possible in the time frame. There were several delays in the experiment work with
the final experiment only taking place on the 25rd of May due to a combination of bad weather,
control system (SCADA) problems, maintenance work on the system etc. Thankfully, Mats was
flexible enough to allow me to finish my thesis in June despite these delays.
The evaluation that Mats has filled out was done before all the experiments had been complete
and though the thesis that he read then was almost complete, I had added and edited some parts
based on the points he mentioned in this assessment and comments.
I would’ve like to have done a multi-response optimisation analysis, and it would not have been
very difficult to do using the desirability theory, but it would not have been so meaningful given
that the characterisation was not done for the entire operation range of the MD module and the
level of uncertainty in the results.
The only way to reduce this uncertainty, I was informed by Dr Zaragoza who was my local
supervisor and very knowledgeable in the field, is to perform repetitions of experiments and use
the average value of results obtained and the standard deviations as errors. Of course, because of
time constraints this was not possible for me and I could only perform one or at most two
repetitions of an experiment run.
I think that I have written a fairly comprehensive thesis, if not a bit long, and both my
supervisors were happy with the work I did in the given time span. It was a great practical
learning experience for me to work with the world class facilities at the PSA and after given me a
brief introduction to the system, Guillermo left me to access and operate the system completely
independently with little to no supervision. However we did discuss the results in depth and I
hope that has come through in the results and discussion section.
Thank you for your time and sorry for making such a long thesis!