Post on 14-Apr-2018
7/27/2019 Electro Final Press Ashish
1/26
a s h i s h . r a c h m a l e 9 2 @ g m a i l . c o m
2012
ELECTRO-DYNAMIC
TETHER
-BY ASHISH RACHMALE
VIT,Pune,India
A RESEARCH / SEMINAR REPORT ON:
7/27/2019 Electro Final Press Ashish
2/26
ELECTRODYNAMIC TETHER
Department of Electronics Engineering
Vishwakarma Institute of Technology 1
A
TECHNICAL SEMINAR REPORT
ON
ELECTRODYNAMIC TETHER
Ashish V. Rachmale
7/27/2019 Electro Final Press Ashish
3/26
ELECTRODYNAMIC TETHER
Department of Electronics Engineering
Vishwakarma Institute of Technology 2
DEPARTMENT OF ELECTRONICS ENGINEERING
VISHWAKARMA INSTITUTE OF TECHNOLOGY
(An Autonomous Institute ,Affiliated to Pune University)
Academic Year 2012-13
7/27/2019 Electro Final Press Ashish
4/26
ELECTRODYNAMIC TETHER
Department of Electronics Engineering
Vishwakarma Institute of Technology 3
ABSTRACT
Electrodynamic tethers (EDTs) are long conducting wires, such as one deployed
from a tether satellite, which can operate on electromagnetic principles, by converting
their kinetic energy to electrical energy(as generators), converting electrical energy to
kinetic energy(or asmotors).
Electric potential is generated across a conductive tether by its motion through the
Earth's magnetic field.
As part of a tether propulsion system, crafts can use long, strong conductors
(though not all tethers are conductive) to change the orbits of spacecraft. It has the
potential to make space travel significantly cheaper. It is a simplified, very low-budget
magnetic sail. It can be used either to accelerate or brake an orbiting spacecraft. When
http://en.wikipedia.org/wiki/Tether_satellitehttp://en.wikipedia.org/wiki/Tether_satellitehttp://en.wikipedia.org/wiki/Kinetic_energyhttp://en.wikipedia.org/wiki/Kinetic_energyhttp://en.wikipedia.org/wiki/Electrical_energyhttp://en.wikipedia.org/wiki/Electrical_energyhttp://en.wikipedia.org/wiki/Electrical_generatorhttp://en.wikipedia.org/wiki/Electrical_generatorhttp://en.wikipedia.org/wiki/Electrical_generatorhttp://en.wikipedia.org/wiki/Electric_motorhttp://en.wikipedia.org/wiki/Electric_motorhttp://en.wikipedia.org/wiki/Electric_motorhttp://en.wikipedia.org/wiki/Tether_propulsionhttp://en.wikipedia.org/wiki/Tether_propulsionhttp://en.wikipedia.org/wiki/Tetherhttp://en.wikipedia.org/wiki/Tetherhttp://en.wikipedia.org/wiki/Orbithttp://en.wikipedia.org/wiki/Orbithttp://en.wikipedia.org/wiki/Spacecrafthttp://en.wikipedia.org/wiki/Spacecrafthttp://en.wikipedia.org/wiki/Magnetic_sailhttp://en.wikipedia.org/wiki/Magnetic_sailhttp://en.wikipedia.org/wiki/Magnetic_sailhttp://en.wikipedia.org/wiki/Spacecrafthttp://en.wikipedia.org/wiki/Orbithttp://en.wikipedia.org/wiki/Tetherhttp://en.wikipedia.org/wiki/Tether_propulsionhttp://en.wikipedia.org/wiki/Electric_motorhttp://en.wikipedia.org/wiki/Electrical_generatorhttp://en.wikipedia.org/wiki/Electrical_energyhttp://en.wikipedia.org/wiki/Kinetic_energyhttp://en.wikipedia.org/wiki/Tether_satellite7/27/2019 Electro Final Press Ashish
5/26
ELECTRODYNAMIC TETHER
Department of Electronics Engineering
Vishwakarma Institute of Technology 4
direct current is pumped through the tether, it exerts a forceagainst the magnetic field,
and the tether accelerates the spacecraft.
It has a strong potential for providing propellant less propulsion to spacecraft in
low earth orbit. An electrodynamic Tether uses the same principle as electric motor in
toys, appliances and computer disk drives. It works as a thruster, because a magnetic field
exerts a force on a current carrying wire. The magnetic field is supplied by the earth. By
properly controlled the forces generated by this electrodynamic tether can be used to pull
or push a spacecraft to act as brake or a booster.
NASA plans to lasso energy from Earths atmosphere with a tether act as part of
first demonstration of a propellant-free space propulsion system, potentially leading to a
revolutionary space transportation system. Working with Earths magnetic field would
benefit a number of spacecraft including the International Space Station.
http://en.wikipedia.org/wiki/Direct_currenthttp://en.wikipedia.org/wiki/Direct_currenthttp://en.wikipedia.org/wiki/Lorentz_forcehttp://en.wikipedia.org/wiki/Lorentz_forcehttp://en.wikipedia.org/wiki/Lorentz_forcehttp://en.wikipedia.org/wiki/Direct_current7/27/2019 Electro Final Press Ashish
6/26
ELECTRODYNAMIC TETHER
Department of Electronics Engineering
Vishwakarma Institute of Technology 5
TABLE OF CONTENTS
1. INTRODUCTION ....7
2. WHY TETHERS WIN ! ......8
3. HISTORY................10
4. FUNDAMENTALS OF
EDTs.11
4.1.Principle
4.2.Lorentz Force Law
4.3.Flemings Left Hand Rule
5. WORKING..13
6. ENGINEERING OF ELECTRODYNAMIC
TETHER................15
6.1.Mathematics Of EDT
6.2.Voltage across conductor
6.3.Current in conductor
6.4.Tether current
6.5.Circuit Diagram
6.6.Physics in EDTs
7.APPLICATIONS21
7.1.Propellant less Propulsion for LEO Spacecraft
7/27/2019 Electro Final Press Ashish
7/26
ELECTRODYNAMIC TETHER
Department of Electronics Engineering
Vishwakarma Institute of Technology 6
7.2.Power Generation in Low Earth Orbit
7.3.Electro Dynamic Revision-Boost of the International Space Station
7.4.Space Junk Cleanup
7.5.Satellite Tugboat
7.6.Exploring the Outer Planets
8. FUTURE SCOPE...23
9.CONCLUSION24
10.REFERENCES..25
10.1.Websites
10.2.Books and Magazines
7/27/2019 Electro Final Press Ashish
8/26
ELECTRODYNAMIC TETHER
Department of Electronics Engineering
Vishwakarma Institute of Technology 7
1.INTRODUCTION
Satellites have a major part to play in the present communication system. These
satellites are launched with the help of rockets. Typically a payload will placed by a
rocket into Low Earth Orbit or LEO (around 400 km) and then boosted higher by rocket
thrusters. But just transporting a satellite from the lower orbit to its eventual destination
can to several thousand dollars per kilogram of payload. To cut expenses space experts
are reconsidering the technology used to place payload in their final orbits.
There are over eight thousand satellites and other large objects in orbit around the
Earth, and there are countless smaller pieces of debris generated by spacecraft explosions
between satellites. Until recently it has been standard practices to put a satellite in to and
leave it there.However the number of satellites has grown quickly, and as a result, the
amount of orbital debris is growing rapidly. Because this debris is traveling at orbital
speed (78km/s), it poses a significant threat to the space shuttle, the International Space
Station and the many satellites in Earth orbit.
Called an Electrodynamic tether provides a simple and reliable alternative to the
conventional rocket thrusters.Functionally, electrons flow from the space plasma into the
conductive tether, are passed through a resistive load in a control unit and are emitted into
the space plasma by an electron emitter as free electrons. In principle, compact high-
current tether power generators are possible and, with basic hardware, tens, hundreds, and
thousands of kilowatts appears to be attainable.
Electrodynamic tethers work by virtue of the force a magnetic field exerts on a
current carrying wire. In essence, it is a clever way of getting an electric current to flow
in a long conducting wire that is orbiting Earth, so that earths magnetic field will exerts a
force on and accelerate the wire and hence any payload attached to it. By reversing the
direction of current in it, the same tether can be used to deorbit old satellites.
7/27/2019 Electro Final Press Ashish
9/26
ELECTRODYNAMIC TETHER
Department of Electronics Engineering
Vishwakarma Institute of Technology 8
2.WHY TETHERS WIN.!
COMPARISION OF EDT WITH CONVENTIONAL
METHODS
One method of removing a satellite from orbit would be to carry extra propellant
so that the satellite can bring itself down out of orbit. However this method requires a
large mass of propellant and every kilo of propellant that must be carried up reduces the
weight available for revenue-producing transponders. Moreover this requires that the
rocket and satellites guidance systems must be functional after sitting in orbit for ten
years or more.
COST-EFFICIENCY OF EDTs IN REMOVAL OF DEBRIS
What can, without rockets, deploy satellite to Earth-orbit or fling them in to deep
space, can generate electrical power in space, can then catch and eliminate space junk
7/27/2019 Electro Final Press Ashish
10/26
ELECTRODYNAMIC TETHER
Department of Electronics Engineering
Vishwakarma Institute of Technology 9
String! Sounds impossible, but the development in Electrodynamic Space-tethers may
be as significant to future space development as rockets were to its beginnings. Tether
propulsion is completely reusable and environmentally clean,,provides all these features
at low cost and requires no extra fuel.
Much of the weight of any launch vehicle is the propellant and It is expensive to
lift heavy propellants off the ground. Since ED tethers require no propellant, they could
substantially reduce the weight of the spacecraft and provide a cost effective method.
7/27/2019 Electro Final Press Ashish
11/26
ELECTRODYNAMIC TETHER
Department of Electronics Engineering
Vishwakarma Institute of Technology 10
3.HISTORY
Tsiolkovsky once proposed a tower so tall that it reached into space, so that it
would be held there by the rotation of theEarth. However, there was no realistic way to
build it.
To try to solve the problems in Komsomolskaya Pravda(July 31, 1960), another
Russian,Yuri Artsutanov, wrote in greater detail about the idea of a tensile cable to be
deployed from ageosynchronous satellite; downwards towards the ground, and upwards
away; keeping the cable balanced. This is the space elevatoridea, a type of synchronous
tether that would rotate with the Earth. However, given the materials, this too was
impractical on Earth.
In the 1970s Jerome Pearson explored synchronous tethers further, and in
particular analysed the lunar elevatorthat can go through theL1 and L2 points, and this
was found to be possible with materials then existing.
In 1977 Hans Moravec and later Robert L. Forward investigated the physics of
synchronous and non synchronous skyhooktethers, and performed detailed simulations
of tapered tethers that could pick objects off and place objects onto theMoon,Marsandotherplanets, with little, or even a net gain of energy.
In 1979 theUSANASAexamined the feasibility of the idea and gave direction to
the study of tethered systems, especially tethered satellites. In 2000, the NASA and
Boeing considered a HASTOL concept where a tether would take payloads from a
hypersonic aircraft (at half of orbital velocity) toorbit.
http://en.wikipedia.org/wiki/Tsiolkovskyhttp://en.wikipedia.org/wiki/Tsiolkovskyhttp://en.wikipedia.org/wiki/Planet_Earthhttp://en.wikipedia.org/wiki/Planet_Earthhttp://en.wikipedia.org/wiki/Planet_Earthhttp://en.wikipedia.org/wiki/Komsomolskaya_Pravdahttp://en.wikipedia.org/wiki/Komsomolskaya_Pravdahttp://en.wikipedia.org/wiki/Russiahttp://en.wikipedia.org/wiki/Russiahttp://en.wikipedia.org/wiki/Yuri_Artsutanovhttp://en.wikipedia.org/wiki/Yuri_Artsutanovhttp://en.wikipedia.org/wiki/Yuri_Artsutanovhttp://en.wikipedia.org/wiki/Geosynchronous_satellitehttp://en.wikipedia.org/wiki/Geosynchronous_satellitehttp://en.wikipedia.org/wiki/Geosynchronous_satellitehttp://en.wikipedia.org/wiki/Space_elevatorhttp://en.wikipedia.org/wiki/Space_elevatorhttp://en.wikipedia.org/wiki/Jerome_Pearsonhttp://en.wikipedia.org/wiki/Jerome_Pearsonhttp://en.wikipedia.org/wiki/Lunar_elevatorhttp://en.wikipedia.org/wiki/Lunar_elevatorhttp://en.wikipedia.org/wiki/Lunar_elevatorhttp://en.wikipedia.org/wiki/Lagrange_pointhttp://en.wikipedia.org/wiki/Lagrange_pointhttp://en.wikipedia.org/wiki/Lagrange_pointhttp://en.wikipedia.org/wiki/Hans_Moravechttp://en.wikipedia.org/wiki/Hans_Moravechttp://en.wikipedia.org/wiki/Robert_L._Forwardhttp://en.wikipedia.org/wiki/Robert_L._Forwardhttp://en.wikipedia.org/wiki/Robert_L._Forwardhttp://en.wikipedia.org/wiki/Skyhook_%28structure%29http://en.wikipedia.org/wiki/Skyhook_%28structure%29http://en.wikipedia.org/wiki/Skyhook_%28structure%29http://en.wikipedia.org/wiki/Moonhttp://en.wikipedia.org/wiki/Moonhttp://en.wikipedia.org/wiki/Moonhttp://en.wikipedia.org/wiki/Marshttp://en.wikipedia.org/wiki/Marshttp://en.wikipedia.org/wiki/Marshttp://en.wikipedia.org/wiki/Planetshttp://en.wikipedia.org/wiki/Planetshttp://en.wikipedia.org/wiki/Planetshttp://en.wikipedia.org/wiki/USAhttp://en.wikipedia.org/wiki/USAhttp://en.wikipedia.org/wiki/NASAhttp://en.wikipedia.org/wiki/NASAhttp://en.wikipedia.org/wiki/NASAhttp://en.wikipedia.org/wiki/Boeinghttp://en.wikipedia.org/wiki/Boeinghttp://en.wikipedia.org/wiki/HASTOLhttp://en.wikipedia.org/wiki/HASTOLhttp://en.wikipedia.org/wiki/Orbithttp://en.wikipedia.org/wiki/Orbithttp://en.wikipedia.org/wiki/Orbithttp://en.wikipedia.org/wiki/Orbithttp://en.wikipedia.org/wiki/HASTOLhttp://en.wikipedia.org/wiki/Boeinghttp://en.wikipedia.org/wiki/NASAhttp://en.wikipedia.org/wiki/USAhttp://en.wikipedia.org/wiki/Planetshttp://en.wikipedia.org/wiki/Marshttp://en.wikipedia.org/wiki/Moonhttp://en.wikipedia.org/wiki/Skyhook_%28structure%29http://en.wikipedia.org/wiki/Robert_L._Forwardhttp://en.wikipedia.org/wiki/Hans_Moravechttp://en.wikipedia.org/wiki/Lagrange_pointhttp://en.wikipedia.org/wiki/Lunar_elevatorhttp://en.wikipedia.org/wiki/Jerome_Pearsonhttp://en.wikipedia.org/wiki/Space_elevatorhttp://en.wikipedia.org/wiki/Geosynchronous_satellitehttp://en.wikipedia.org/wiki/Yuri_Artsutanovhttp://en.wikipedia.org/wiki/Russiahttp://en.wikipedia.org/wiki/Komsomolskaya_Pravdahttp://en.wikipedia.org/wiki/Planet_Earthhttp://en.wikipedia.org/wiki/Tsiolkovsky7/27/2019 Electro Final Press Ashish
12/26
ELECTRODYNAMIC TETHER
Department of Electronics Engineering
Vishwakarma Institute of Technology 11
4.FUNDAMENTALS OF EDTs
4.1.PRINCIPLE
The basic principle of an electrodynamic tether is Lorentz force. It is the force
that a magnetic field exerts on a current carrying wire in a direction perpendicular to both
the direction of current flow and the magnetic field vector.
4.2.Lorentz Force Law
The Lorentz Force Law can be used to describe the effect of a charged particle moving
in a constant magnetic field.
The Dutch physicist Hendrik Androon Lorentz showed that a moving electric
charge experiences a force in a magnetic field. (if the charge is at rest, there will not be
any force on it due to magnetic field ) Hence it is clear that the force experienced by a
current conductor in a magnetic field is due to the drifting of electrons in it. If a current I
flows through a conductor of cross-section A then I = neAv where v is the drift speed of
electronics n is number density in the conductor and e the electronic charge.
For an element dI of the conductor Id = nAdIev But Adi is the volume of the
current element. Therefore, nAdI represents the number (N) of electrons in the element
Hence,
nAdIe =Ne=q,
Thus in above equation represents q is the total charge in the element
Therefore, IdI=qv
But, the force dF on a current carrying element dI in a magnetic field B is given by
dF=IdIBi.e.,dF=qvB
This fundamental force on a charge q moving with a velocity v in a magnetic field B is
called the Magnetic Lorentz Force.
7/27/2019 Electro Final Press Ashish
13/26
ELECTRODYNAMIC TETHER
Department of Electronics Engineering
Vishwakarma Institute of Technology 12
The simplest form of this law given by the scalar equation
F = QvB
F is the force acting on the particle (vector)
V is the velocity of the particle (vector)
Q is charge of particle (scalar)
B is magnetic field (vector)
NOTE: In this case is for v and B perpendicular to each other otherwise use F = QvB (sin
(X) ) where X is the angle between v and B, when v and B are perpendicular X =90 deg.
So sin (x) =1.
Flemings left hand rule comes in to play here to figure out which way the force is acting
4.3.Flemings Left Hand Rule
For a charged particle moving (velocity v) in a magnetic field (field B) the direction of
the resultant force (force F) can be found by:
MIDDLE FINGER of left hand in direction of CURRENT
INDEX FINGER of left hand in direction of FIELD. B
THUMB now points in direction of the FORCE OR MOTION. F
The force will always be perpendicular to the plane of vector v and B no matter what the
angle between v and B is.
7/27/2019 Electro Final Press Ashish
14/26
ELECTRODYNAMIC TETHER
Department of Electronics Engineering
Vishwakarma Institute of Technology 13
5.WORKING
An electrodynamic tether is essentially a long conducting wire extended from a
space craft. The electrodynamic tether is made from aluminium alloy and typically
between 5 and 20 kilometers long. It extends downwards from an orbiting platform.
Aluminium alloy is used since it is strong, lightweight, inexpensive and easily machined.
The gravity gradient field (also known as tidal force) will tend to orient the tether
in a vertical position. If the tether is orbiting around the Earth, it will be crossing the
earths magnetic field lines orbital velocity (7-8 km/s). The motion of the conductor
across the magnetic field induces a voltage along the length of the tether. The voltage
thus created along its length can be up to several hundred volts per kilometer.
In an electrodynamic tether drag system such as the terminator Tether, the tether
can be used to reduce the orbit of the spacecraft to which it is attached. If the system has
a means for collecting electrons from the ionospheric plasma at one end of the tether and
expelling them back in to the plasma at the other end of the tether, the voltage can drive a
current along the tether. This current bill, in turn, interact with the Earths magnetic field
to cause a Lorentz JXB force, which will oppose the motion of the tether and whatever it
is attached to. This electrodynamics drag force will decrease the orbit of the tether and its
host spacecraft. Essentially, the tether converts the orbital energy of the host spacecraft in
to electrical power, which is dissipated as ohmic heating in the tether.
In an electrodynamic propulsion system, the tether can be used to boost the orbit
of the spacecraft. If a power supply is added to the tether system and used to drive current
in the direction opposite to that which it normally wants to flow, the tether can push
against the Earths magnetic field to raise the spacecrafts orbit. The major advantage of
this technique compared to the other space propulsion system is t hat it doesnt require
any propellant. It uses Earths magnetic field as its reaction mass. By eliminating the
need to launch large amounts of propellant in to orbit, electrodynamic tethers can greatly
reduce the cost of in-space propulsion.The tether is dragged through the atmosphere
ionosheric plasma. The rarefied medium of electrons through which the whole set up is
traveling at a speed of 7-8km/s. In so doing, the 5-km. long aluminium wire extracts
electrons from the plasma at the end farthest from the payload and carries them to the
7/27/2019 Electro Final Press Ashish
15/26
ELECTRODYNAMIC TETHER
Department of Electronics Engineering
Vishwakarma Institute of Technology 14
near end (plasma chamber tests have verified that thin bare wires can collect current from
plasma). There a specially designed devise known as a hollow cathode emitter expels the
electrons, to ensure their return to space currents in the circuit.
Ordinarily, a uniform magnetic field acting on a current-bearing loop of wire yields a net
force of zero, since that cancels the force on one side of the loop on the other side, in
which the current is flowing in the opposite direction However, since the tethered system
is not mechanically attached to the plasma. The magnetic force on the plasma current in
the space does not cancel the forces on the tether. And so the tether experiences a net
force.
As the tether cuts across the magnetic field, its bias voltage is positive at the end
farthest from Earth and negative at the near end. This polarization is due to the action of
Lorentz force on the electrons in the tether. Thus the natural upward current flow due to
the (negatively charged) electrons in the ionosphere being attracted to the tethers far and
then returned to the plasma at the near end. Aided by the hollow cathode emitter. The
hollow cathode is vital: without it, the wires charge distribution would quickly reach
equilibrium and no current would flows.Switching on the hollow cathode causes a small
tungsten tube to heat up and fill with xenon gas from small tank. Electrons from the
tether interacted with the heated gas to create ion plasma. At the far end of the tube. a so
called keeper electrode, which is positively charged with respect to the tube. Draw the
electrons and expels them to space. (the xenon ions, mean while are collected by the
hollow cathode and used to provide additional heating). The rapid discharge of electrons
invites new electrons to follow from the tether and out through the hollow cathode.
Earths magnetic field exerts a drag force on a current carrying tether, decelerating it and
the payload and rapidly lowering their orbit Eventually they re-enter Earths atmosphere.
7/27/2019 Electro Final Press Ashish
16/26
ELECTRODYNAMIC TETHER
Department of Electronics Engineering
Vishwakarma Institute of Technology 15
6.ENGINEERING OF ELECTRODYNAMIC
TETHER
6.1.MATHEMATICS OF EDT
A motional electromotive force (EMF) is generated across a tether element as it
moves relative to a magnetic field. The force is given by Faraday's Law of Induction:
Without loss of generality, it is assumed the tether system is in Earth orbit and it
moves relative to Earths magnetic field. Similarly, if current flows in the tether element,
a force can be generated in accordance with the Lorentz Force Equation
In self-powered mode (de-orbit mode), this EMF can be used by the tether system
to drive the current through the tether and other electrical loads (e.g. resistors, batteries),
emit electrons at the emitting end, or collect electrons at the opposite. In boost mode, on-
board power supplies must overcome this motional EMF to drive current in the opposite
direction, thus creating a force in the opposite direction, as seen in below figure, and
boosting the system.
7/27/2019 Electro Final Press Ashish
17/26
ELECTRODYNAMIC TETHER
Department of Electronics Engineering
Vishwakarma Institute of Technology 16
Illustration of the EDT concept
At 300-km altitude, the Earths magnetic field, in the north-south direction, is
approximately 0.18 0.32 Gauss up to ~40 inclination, and the orbital velocity with
respect to the local plasma is about 7500 m/s. This results in a Vemf range of 35 250
V/km along the 5-km length of tether. This EMF dictates the potential difference across
the bare tether which controls where electrons are collected and / or repelled. Here, the
ProSEDS de-boost tether system is configured to enable electron collection to the
positively biased higher altitude section of the bare tether, and returned to the ionosphere
at the lower altitude end. This flow of electrons through the length of the tether in the
presence of the Earths magnetic field creates a force that produces a drag thrust that
helps de-orbit the system, as given by the above equation. The boost mode is similar to
the de-orbit mode, except for the fact that a High Voltage Power Supply (HVPS) is also
inserted in series with the tether system between the tether and the higher positive
potential end. The power supply voltage must be greater than the EMF and the polar
opposite. This drives the current in the opposite direction, which in turn causes the higher
http://en.wikipedia.org/wiki/File:Fig12_Tether_System.PNG7/27/2019 Electro Final Press Ashish
18/26
ELECTRODYNAMIC TETHER
Department of Electronics Engineering
Vishwakarma Institute of Technology 17
altitude end to be negatively charged, while the lower altitude end is positively
charged(Assuming a standard east to west orbit around Earth).
6.2.Voltage across conductor
With a long conducting wire of length L , an electric field E is generated in the
wire. It produces a voltage V between the opposite ends of the wire. This can be
expressed as:
where the angle is between the length vector (L ) of the tether and the electric field
vector (E), assumed to be in the vertical direction at right angles to the velocity vector ( v)in plane and the magnetic field vector (B) is out of the plane.
6.3.Current in conductor
An electrodynamic tether can be described as a type ofthermodynamically"open
system". Electrodynamic tether circuits cannot be completed by simply using another
wire, since another tether will develop a similar voltage. Fortunately, the Earth's
magnetosphere is not "empty", and, in near-Earth regions (especially near the Earth's
atmosphere) there exist highly electrically conductive plasmaswhich are kept partially
ionizedby solar radiation or other radiant energy. The electron and ion density varies
according to various factors, such as the location, altitude, season, sunspot cycle, and
contamination levels. It is known that a positively charged bare conductorcan readily
remove free electrons out of the plasma. Thus, to complete the electrical circuit, a
sufficiently large area of uninsulated conductor is needed at the upper, positively charged
end of the tether, thereby permitting current to flow through the tether.
However, it is more difficult for the opposite (negative) end of the tether to eject
free electrons or to collect positive ions from the plasma. It is plausible that, by using a
very large collection area at one end of the tether, enough ions can be collected to permit
significant current through the plasma. This was demonstrated during the Shuttle orbiter's
http://en.wikipedia.org/wiki/Thermodynamichttp://en.wikipedia.org/wiki/Thermodynamichttp://en.wikipedia.org/wiki/Open_system_%28systems_theory%29http://en.wikipedia.org/wiki/Open_system_%28systems_theory%29http://en.wikipedia.org/wiki/Open_system_%28systems_theory%29http://en.wikipedia.org/wiki/Open_system_%28systems_theory%29http://en.wikipedia.org/wiki/Plasma_%28physics%29http://en.wikipedia.org/wiki/Plasma_%28physics%29http://en.wikipedia.org/wiki/Ionhttp://en.wikipedia.org/wiki/Ionhttp://en.wikipedia.org/wiki/Solar_radiationhttp://en.wikipedia.org/wiki/Solar_radiationhttp://en.wikipedia.org/wiki/Radiant_energyhttp://en.wikipedia.org/wiki/Radiant_energyhttp://en.wikipedia.org/wiki/Conductor_%28material%29http://en.wikipedia.org/wiki/Conductor_%28material%29http://en.wikipedia.org/wiki/Conductor_%28material%29http://en.wikipedia.org/wiki/Radiant_energyhttp://en.wikipedia.org/wiki/Solar_radiationhttp://en.wikipedia.org/wiki/Ionhttp://en.wikipedia.org/wiki/Plasma_%28physics%29http://en.wikipedia.org/wiki/Open_system_%28systems_theory%29http://en.wikipedia.org/wiki/Open_system_%28systems_theory%29http://en.wikipedia.org/wiki/Thermodynamic7/27/2019 Electro Final Press Ashish
19/26
ELECTRODYNAMIC TETHER
Department of Electronics Engineering
Vishwakarma Institute of Technology 18
TSS-1R mission, when the shuttle itself was used as a large plasma contactor to provide
over an ampereof current. Improved methods include creating an electron emitter, such
as a thermionic cathode, plasma cathode, plasma contactor, or field electron
emissiondevice. Since both ends of the tether are "open" to the surrounding plasma,
electrons can flow out of one end of the tether while a corresponding flow of electrons
enters the other end. In this fashion, the voltage that is electromagnetically induced
within the tether can cause current to flow through the surrounding space environment,
completing an electrical circuit through what appears to be, at first glance, an open
circuit.
6.4.Tether current
The amount of current (I) flowing through a tether depends on various factors. One of
these is the circuit's total resistance (R). The circuit's resistance consist of three
components:
1. the effective resistance of the plasma,2. the resistance of the tether, and3. a control variable resistor.In addition, aparasitic loadis needed. The load on the current may take the form of a
charging device which, in turn, charges reserve power sources such as batteries. The
batteries in return will be used to control power and communication circuits, as well as
drive the electron emitting devices at the negative end of the tether. As such the tether
can be completely self-powered, besides the initial charge in the batteries to provide
electrical power for the deployment and startup procedure.
The charging battery load can be viewed as a resistor which absorbs power, but storesthis for later use (instead of immediately dissipating heat). It is included as part of the
"control resistor". The charging battery load is not treated as a "base resistance" though,
as the charging circuit can be turned off at anytime. When off, the operations can be
continued without interruption using the power stored in the batteries.
http://en.wikipedia.org/wiki/Amperehttp://en.wikipedia.org/wiki/Amperehttp://en.wikipedia.org/wiki/Thermionic_cathodehttp://en.wikipedia.org/wiki/Thermionic_cathodehttp://en.wikipedia.org/wiki/Field_electron_emissionhttp://en.wikipedia.org/wiki/Field_electron_emissionhttp://en.wikipedia.org/wiki/Space_environmenthttp://en.wikipedia.org/wiki/Space_environmenthttp://en.wikipedia.org/wiki/Open_circuithttp://en.wikipedia.org/wiki/Open_circuithttp://en.wikipedia.org/wiki/Open_circuithttp://en.wikipedia.org/wiki/Parasitic_loadhttp://en.wikipedia.org/wiki/Parasitic_loadhttp://en.wikipedia.org/wiki/Parasitic_loadhttp://en.wikipedia.org/wiki/Parasitic_loadhttp://en.wikipedia.org/wiki/Open_circuithttp://en.wikipedia.org/wiki/Open_circuithttp://en.wikipedia.org/wiki/Space_environmenthttp://en.wikipedia.org/wiki/Field_electron_emissionhttp://en.wikipedia.org/wiki/Field_electron_emissionhttp://en.wikipedia.org/wiki/Thermionic_cathodehttp://en.wikipedia.org/wiki/Ampere7/27/2019 Electro Final Press Ashish
20/26
ELECTRODYNAMIC TETHER
Department of Electronics Engineering
Vishwakarma Institute of Technology 19
6.5.CIRCUIT DIAGRAM
The below figure describes a typical EDT system in a series bias grounded gate
configuration (further description of the various types of configurations analyzed have
been presented) with a blow-up of an infinitesimal section of bare tether. This figure is
symmetrically set up so either end can be used as the anode. This tether system is
symmetrical because rotating tether systems will need to use both ends as anodes and
cathodes at some point in its rotation. The V_hvps will only be used in the cathode end of
the EDT system, and is turned off otherwise.
(a) A circuit diagram of a bare tether segment with (b) an equivalent EDT system circuit
model showing the series bias grounded gate configuration.
http://en.wikipedia.org/wiki/File:Fig33_Circuit_Setup.PNG7/27/2019 Electro Final Press Ashish
21/26
ELECTRODYNAMIC TETHER
Department of Electronics Engineering
Vishwakarma Institute of Technology 20
6.6.PHYSICS IN EDTs
To calculate the in-plane and out-of-plane directions, the components of the
velocity and magnetic field vectors must be obtained and the force values calculated. The
component of the force in the direction of travel will serve to enhance the orbit raising
capabilities, while the out-of-plane component of thrust will alter the inclination. In the
below figure, the magnetic field vector is solely in the north (or y-axis) direction, and the
resulting forces on an orbit, with some inclination, can be seen. An orbit with no
inclination would have all the thrust in the in-plane direction.
Description of an in-plane and out-of-plane force.
Drag effects on an
Electrodynamic Tether system
There has been work conducted to stabilize the librations of the tether system to
prevent misalignment of the tether with the gravity gradient. The below figure displaysthe drag effects an EDT system will encounter for a typical orbit. The in-plane angle,
_ip, and out-of-plane angle, _op, can be reduced by increasing the endmass of the
system, or by employing feedback technology.Any deviations in the gravity alignment
must be understood, and accounted for in the system design.
http://en.wikipedia.org/wiki/File:Fig35_Orbit_Drag.PNGhttp://en.wikipedia.org/wiki/File:Fig34_Plane_Thrust.PNGhttp://en.wikipedia.org/wiki/File:Fig35_Orbit_Drag.PNGhttp://en.wikipedia.org/wiki/File:Fig34_Plane_Thrust.PNG7/27/2019 Electro Final Press Ashish
22/26
ELECTRODYNAMIC TETHER
Department of Electronics Engineering
Vishwakarma Institute of Technology 21
7.APPLICATIONS
7.1.Propellant less Propulsion for LEO Spacecraft
ED tether system can provide propellant less propulsion for spacecraft operating in low
Earth orbit.
7.2.Power Generation in Low Earth Orbit
Electro dynamic tethers may also provide an economical means of electrical power in
orbit.
7.3.Electro Dynamic Revision-Boost of the International Space Station
NASA currently plans to launch several large rockets every year to carry fuel up to the
station so that it can re-boost its orbit.
7.4.Space Junk Cleanup
The most direct application of ProSEDS would be to get rid of space junk.
7.5.Satellite Tugboat
Another idea is for the ED tether to be attached to an unmanned space tugboat
that would ferry satellites to higher orbits. After being launched in to low Earth orbit, the
7/27/2019 Electro Final Press Ashish
23/26
ELECTRODYNAMIC TETHER
Department of Electronics Engineering
Vishwakarma Institute of Technology 22
so called Orbital Transfer Vehicle would grapple the satellite and maneuver it to a new
altitude or inclination. The tug could then lower its own orbit to rendezvous with another
payload and repeat the process
7.6.Exploring the Outer Planets
Perhaps the most exotic use of ED tether technology would be to propel and
power spacecraft exploring the outer planets. Existing vessels have relied on solar cells,
but at distances far from the Sun, the power available is typically less than 100 W.
Jupiter and its moons have an environment particularly favorable to ED tethers; the
planet has a strong magnetic field and a rapid rotation rate, and its mass dictates high
orbital velocities. With the magnetic field moving much faster than the spacecraft, the
tether would essentially be stealing energy from the planet's magnetic field.
7/27/2019 Electro Final Press Ashish
24/26
ELECTRODYNAMIC TETHER
Department of Electronics Engineering
Vishwakarma Institute of Technology 23
8.FUTURE SCOPE
Researchers are investigating the use of ED tethers to
extend and enhance future scientific missions to Jupiter and its moons. In theory, Ed
tether propulsion could be used near any planet with a Previous visits to the largest planet
in the solar system - including the "Grand Tour" flyby missions of Voyager 1 and 2,
launched in 1977, and an orbital visit by the Galileo probe, which left Earth in 1989 and i
continues to tour and study the Jovian system today- were illuminating, but the fuel
limitations and minimum maneuverability of those probes hampers long term, more
detailed scientific study.
Development of a propellant free, ED tether propulsion system would make it
possible to put a long term probe in Jupiter's orbit - one that could leverage the planet's
powerful magnetic field and magneto sphere to travel freely among the Jovian
moons,providing more information and new insight about them as well.
Tether Transport from Low Earth to the Lunar Surface
A concept developed by Tethers Unlimited wherein several rotating tethers in orbit
around the earth and moon may provide a means of exchanging supplies between low
Earth orbit facilities and Lunar bases without requiring the use of propellants.
Tethers for Rapid Autonomous Deorbit of Leo Satellites
Tethers Unlimited Inc. is currently developing a system called "Terminator Tether" that
will provide a low cost, light weight and reliable method of removing objects from Low
Earth Orbit (LEO).
7/27/2019 Electro Final Press Ashish
25/26
ELECTRODYNAMIC TETHER
Department of Electronics Engineering
Vishwakarma Institute of Technology 24
9.CONCLUSION
Electrodynamic tether now becoming the most popular fuel carrier for space
crafts. The use of space tethers is the answer to all the current problems as they dont
require propellents..ED tethers can provide long-term propellant less propulsion
capability for orbital maneuvering and station keeping of small satellites in low-Earth-
orbit..
Over the years, numerous applications for electrodynamic tethers have been
identified for potential use in industry, government, and scientific exploration.
Electro dynamic tethers may also provide an economical means of electrical
power in orbit. TUI is currently developing a propulsion system called the "Micro
satellite Propellant less Electro dynamic Tether Propulsion System"
Beyond these,ETDs are opening new doors in space explorations and getting
close to the answer of ARE WE ALONE in this universe..
The universe is eagerly waiting for the application of these tethers in future..!
7/27/2019 Electro Final Press Ashish
26/26
ELECTRODYNAMIC TETHER
Department of Electronics Engineering
10.REFERENCES
10.1.WEBSITES:
http://www.tethers.com/
http://www.wikipedia.org/
http://www.ieee.com/
http://www.tuiengineering.com/
http://www.google.com/
10.2.BOOKS and MAGAZINES:
THE TERMINATOR TETHER - HOYT, R.P., FORWARD, R.L
DYNAMICS OF SPACE TETHER SYSTEMS - BELETSKII, V.V.. LEVIN,
STABILIZATION OF ELECTRODYNAMIC - HOYT. R.P & HEINEN
SPACE TETHERS
ELECTRON ICS FOR YOU - JANUARY 2005
ELECTRONICS TODAY - JUNE 2004
ASHISH RACHMALE
2012-13
http://www.tethers.com/http://www.tethers.com/http://www.wikipedia.org/http://www.wikipedia.org/http://www.tuiengineering.com/http://www.tuiengineering.com/http://www.google.com/http://www.google.com/http://www.google.com/http://www.tuiengineering.com/http://www.wikipedia.org/http://www.tethers.com/