Post on 08-Feb-2018
7/22/2019 Electrical M07 Sensors en TXT
1/28Caterpillar: Confidential Yellow
GlobalManpowerDevelopMent
electronIcStroubleShootInGIltSwItcheS/SenSorS/SolenoIDSMoDule7 - textreference
Serv1877
electronics troubleshooting IltModule 7 - Switches/Sensors/Solenoids
text reference
2010 Caterpillar Inc.
7/22/2019 Electrical M07 Sensors en TXT
2/28
Caterpillar: Confidential Yellow
SERV1877 - 03/10 Module 7 - Switches/Sensors/Solenoids-2-
2_1
Switches
Electronic control systems use several types of switches. Switches may eithermonitor an engine or machine parameter or may be operator activated. They allhave similar functions and are typically two-state devices (ON or OFF) that providepower or grounded inputs in order to control devices.
7/22/2019 Electrical M07 Sensors en TXT
3/28
Caterpillar: Confidential Yellow
SERV1877 - 03/10 Module 7 - Switches/Sensors/Solenoids-3-
ParameterMonitored Switch Makeup
Temperature Variable Input with Thermistor or Thermocouple
PressureStrain Gauge with Variable Resistor and SwitchBellows w/Induction or Capacitor and Switch
Fluid Flow Paddle with Switch
OperatorActivated
- Toggle- Push / Pull- Momentary (Hold)- Push to Set / Push to Release
SWITCHES (ON / OFF INPUT DEVICES)
3_1The above chart shows switches (on/off input devices) classified by the parametemonitored and the switch makeup. Temperature, pressure, fluid flow, and coolan
level switches include a variable resistor or some other method of turning the switcon or off such as a thermocouple. When the machine conditions exceed or decreasbelow a specified limit, the switch opens (or closes) and sends a signal to the ECU.Operator activated switches send a signal to the ECU when the switch is manuallactivated by the operator.
7/22/2019 Electrical M07 Sensors en TXT
4/28
Caterpillar: Confidential Yellow
SERV1877 - 03/10 Module 7 - Switches/Sensors/Solenoids-4-
Rear Brake
4_1
Main Display Module
GNBK
BK 18BK 18
T
Rear Brake Oil
Temperature Switch
temperature Switch
4_2
The top photo shows a brake oil temperature switch (arrow) located on an articulatedtruck. The temperature switch contacts are normally closed. When the engineis running and brake oil temperature is within the desired range determined byengineering, the contacts stay closed and complete the ground circuit. The switchopens once the brake oil temperature exceeds an acceptable limit, alerting theoperator of the condition.
This type of temperature switch can be tested using a digital multimeter on the voltsor ohms scale. An excessive voltage drop across the terminals would indicate adefective switch.
7/22/2019 Electrical M07 Sensors en TXT
5/28
Caterpillar: Confidential Yellow
SERV1877 - 03/10 Module 7 - Switches/Sensors/Solenoids-5-
2Brake Oil Pressure 20
B
5_1
Main Display Module
BK 16
PK 16
RD 16
BK 16
Brake OilPressure Switch
5_2
pressure Switch
The top photo shows a brake oil pressure switch (arrow). The pressure-type switchcontacts are normally open (engine not running/low oil pressure). When the engineis running and brake oil pressure is within the desired range, the contacts close andcomplete the ground circuit.
If brake oil pressure drops to a level where the contacts open, the switch will interruptthe ground circuit signal to the ECU, causing the ECU to activate a fault condition.In the case of a broken wire, the ECU will interpret the signal in the same manner asa low pressure event.
This type of pressure switch can be tested using a digital multimeter on the voltsor ohms scale. An excessive voltage drop across the terminals when adequate
pressure is present would indicate a defective switch.
7/22/2019 Electrical M07 Sensors en TXT
6/28
Caterpillar: Confidential Yellow
SERV1877 - 03/10 Module 7 - Switches/Sensors/Solenoids-6-
6_1
Engine ECM
GroundBU 16
2 BK 16BK 18BK 18
Coolant Flow 18 Coolant Flow Switch
6_2
flow Switch
The top photo shows an example of a coolant flow switch. The flow switch is apaddle type and is normally open, closing once there is sufficient fluid flow. If flow isrestricted, the switch will interrupt the ground circuit signal to the ECU, causing theECU to activate a fault condition. In the case of a broken wire, the ECU will interpretthe signal in the same manner as reduced or no flow.
This type of switch can be tested using a digital multimeter on the volts or ohms scale.An excessive voltage drop across the terminals when adequate flow is present (orwhen the paddle is hand actuated) would indicate a defective switch.
7/22/2019 Electrical M07 Sensors en TXT
7/28
Caterpillar: Confidential Yellow
SERV1877 - 03/10 Module 7 - Switches/Sensors/Solenoids-7-
Sensor r Ret r 12 BN
Parking BrakeOp tc 44
16 1PK 16
7_1
Transmission ECM J1
Parking
Brake Switch
operator-activated Switch
7_2
Operator activated switches send a signal to the ECU when activated by the operator.The switch opens or closes and sends a signal to the ECU informing the ECU toperform an action. In this application a parking brake switch (arrow) on an articulatedtruck sends a signal to the ECU when actuated by the operator. The ECU processesthe signal and sends an output signal to engage the parking brake.
This type of switch can be tested using a digital multimeter on the volts or ohmsscale. An excessive voltage drop or excessive resistance across the terminals whilethe switch is closed would indicate a defective switch.
7/22/2019 Electrical M07 Sensors en TXT
8/28
Caterpillar: Confidential Yellow
SERV1877 - 03/10 Module 7 - Switches/Sensors/Solenoids-8-
ParameterMonitored SensorMakeup Active orPassive DMMMeasurements
Speed Pickup Coil Passive (2 Wire) Volts / Hz / OhmsHall Effect Active (2/3/4 Wire) Volts / Hz / Duty Cycle
TemperatureVariable Resistor Passive (2 Wire) Volts / OhmsVariable Resistor Active (3 Wire) Volts / OhmsVariable Resistor Active (3 Wire) Volts / Hz / Duty Cycle
Pressure Strain Gauge withVariable Resistor
Active (3 Wire) VoltsActive (3 Wire) Volts / Hz / Duty Cycle
PositionVariable Resistor Active (3 Wire)
Volts / Hz / Duty CycleHall Effect Active (3 Wire)Magnetostrictive Active (3 Wire)
Fuel Level Variable Resistor Passive (2 Wire) Volts / OhmsUltrasonic Active (4 Wire) Volts / Hz / Duty Cycle
SENDERS / SENSORS (VARIABLE INPUT DEVICES)
8_1Sensors
Sensors (variable input devices) can be classified in several ways as illustrated ithe chart above. This chart shows the typical sensors and senders found on Caengines and machines.
The types of senders and sensors in this chart are classified by the parametermonitored. Other sensor characteristics include:
Sensor Makeup: Internal components that determine the type of signalproduced.
Active or Passive: An active sensor receives power from the ECU orbattery and must be powered to check operation. A passive sensordoes not require power from the ECU and can be tested without powerapplied.
DMM Measurements: Type of electronic signals for a sensor that adigital multimeter can measure.
NOTE: Most variable input devices are referred to as sensors. The fuel leveinput device with a variable resistor is normally referred to as a sender. Alvariable input devices will be referred to as sensors in this presentation.
7/22/2019 Electrical M07 Sensors en TXT
9/28
Caterpillar: Confidential Yellow
SERV1877 - 03/10 Module 7 - Switches/Sensors/Solenoids-9-
Do not have to be powered inorder to test.
test off engine or machine(static test).
9_1 9_2
passive Sensors
Passive sensors are typically two-wire sensors, with the exception of single-wiresenders. Passive sensors do not require ECU or battery power in order to functionand test. Testing can usually be accomplished by checking the resistance of the
sensor. All passive sensors will be of the analog type.
Pin assignments for passive sensors are as follows:
Position 1: Signal
Position 2: Return/Ground
7/22/2019 Electrical M07 Sensors en TXT
10/28
Caterpillar: Confidential Yellow
SERV1877 - 03/10 Module 7 - Switches/Sensors/Solenoids-10-
10_1
10_2
active Sensors
Active sensors are typically three-wire sensors, but can be two- or four-wire. Activesensors require ECU or battery power in order to function and test. Active sensorsfall into one of two categories:
Analog (top photo): A signal that varies smoothly over time and inproportion to the measured parameter. These signals are typically DCvoltage.
Digital (bottom photo): Digital signals are usually associated withcomputerized electronic controls and measuring devices. The signal(s)will switch between two distinct levels, such as 0 to +10 Volts, or moresimply stated as low and high. The internal electronics of a sensordetermine the amplitude or level.
Pin assignments for active sensors are as follows:
A or 1 position: Power
B or 2 position: Return/Ground
C or 3 and 4 position: Signal
7/22/2019 Electrical M07 Sensors en TXT
11/28
Caterpillar: Confidential Yellow
SERV1877 - 03/10 Module 7 - Switches/Sensors/Solenoids-11-
DCV
olts
+
0Pressure (kPa)
11_1
analog Signals
As previously mentioned, an analog signal is a signal that varies smoothly over timeand in proportion to the measured parameter. Analog signals on Cat equipment aretypically AC or DC voltage.
The above illustration shows a DC analog signal trace of a pressure sensor. Thistype of electronic signal is proportional to the amount of pressure sensed in a system.
As pressure increases, the resistance of the sensing device changes. The change inresistance, and thereby voltage, would be sensed by the ECU.
NOTE: Analog sensors that have a DC output will have a typical operatingrange of 0.2 volts to 4.8 volts. Voltage ranges may be different, depending onapplication.
7/22/2019 Electrical M07 Sensors en TXT
12/28
Caterpillar: Confidential Yellow
SERV1877 - 03/10 Module 7 - Switches/Sensors/Solenoids-12-
One Cycle
0
Time12_1
The above illustration depicts a sine wave produced by analog speed/timing sensors.Sine waves are types of signals that change direction (alternating current). In the
above example, the voltage rises to a peak positive value, drops to zero, reversespolarity, rises to a peak negative value, and returns to zero. One positive and onenegative alternation produces one cycle. The cycle is repeated continuously.
The number of cycles that occur in one second is called frequency, expressed in Hertz(Hz). As the speed of the measured parameter increases, so will the frequency.
7/22/2019 Electrical M07 Sensors en TXT
13/28
Caterpillar: Confidential Yellow
SERV1877 - 03/10 Module 7 - Switches/Sensors/Solenoids-13-
hall effect: varying requency,onstant Duty ycle
pwM: onstant requency,varying Duty ycle.
High
Two Distinct
Amplitude Levels
Low
13_1
Digital Signals
As previously stated, digital signals switch between two distinct levels such as 0 to+10 Volts, or more simply stated as high and low. The internal electronics of aspecific device determine the amplitude or level. Digital signals on Cat equipment
are typically of the Hall-Effect or pulse width modulated (PWM) type.
The above illustration depicts a typical Hall-Effect signal. Hall-Effect sensorsoperate using a current field and a piece of iron (gear tooth). When the gear toothis introduced perpendicular to the current field, all of the electrons are forced toone side of the semiconductor (rememberlike forces repel and opposites attract).When current is forced to one side of a semiconductor, a difference in potential(differential voltage change) can be detected. The gear tooth moving across the Hallcell gives a highstate. The lowstate indicates the Hall cell is located in the valley
between two teeth.
Digital signals created by Hall-Effect will have a frequency that varies with the speedof the parameter being measured, and will typically have a constant duty cycle of50%.
7/22/2019 Electrical M07 Sensors en TXT
14/28
Caterpillar: Confidential Yellow
SERV1877 - 03/10 Module 7 - Switches/Sensors/Solenoids-14-
PULSE WIDTH MODULATION
+ OnON (80%) OFF (20%)
0
Off One Period14_1
The above illustration shows a PWM signal. A PWM signal is measured in dutcycle, which is defined as % time on (high) vs. % time off (low) for one pulse. In th
example above, the signal is on (or high) for 80% of the pulse and off (or low) for 20of the pulse. This would indicate a duty cycle of 80%.
On Cat equipment, a position sensor would be a good example of a device thaproduces a PWM signal. A PWM signal has a constant frequency output and thduty cycle (percentage of time on versus time off) of the signal varies as condition(rotary position) change. The output of the sensor is sent to an ECU where the signais processed.
7/22/2019 Electrical M07 Sensors en TXT
15/28
Caterpillar: Confidential Yellow
SERV1877 - 03/10 -15- Module 7 - Switches/Sensors/Solenoids
Sensor ypes
15_1
Sensors convert a physical parameter into an electronic signal. Electronic controlsuse this signal (input information) to monitor engine and machine conditions anddetermine appropriate output signals.
Several different types of sensors provide this input information to the ECU. Theseinclude:
Speed/Timing
Temperature
Pressure
Position
Fluid Level
7/22/2019 Electrical M07 Sensors en TXT
16/28
Caterpillar: Confidential Yellow
SERV1877 - 03/10 Module 7 - Switches/Sensors/Solenoids-16-
basically a small generator.
he Speed/ iming sensorprovides signals to the .
he signals are created as thetiming wheel rotates past thesensor pickup.
unique pattern of teeth indicatesengine position (timing) to the
each tooth is spacedapart the same number ofdegrees, with one extra tooth
in the pattern. he detectsthis extra tooth and uses it asa reference point to determinetiming.
PASSIVE SPEED SENSORS
- Two-Wire Sensor
- Magnetic Pickup Coil
16_1 16_2
DMM MEASUREMENTS
- Volts
- Hz
- Ohms
16_3 16_4
A passive (two-wire) magnetic frequency-type sensor converts mechanical motion toan AC voltage. A typical magnetic pickup consists of a coil, pole piece, magnet, and
housing. The sensor produces a magnetic field that, when altered by the passage ofa gear tooth, generates an AC voltage in the coil. The AC voltage and the frequencyof the AC signal is proportional to speed.
Magnetic pickup sensors rely on the distance between the end of the pickup andthe passing gear teeth to operate properly. Typically, when the pickup is installed, itis turned in until it makes contact with the top of a gear tooth and then turned back
out a partial turn before it is locked in place with a locking nut. A weak signal mayindicate that the sensor is too far away from the gear. It is important to check thespecifications when installing these sensors to insure the proper spacing. Variablegap speed sensors are no longer used on new production equipment as fixed gapsensors are becoming more commonplace.
Magnetic engine speed sensors may be used in pairs. One sensor is specificallydesigned for optimum performance at slower engine speeds which occur duringcranking and when the engine first starts. The other sensor is designed for optimumperformance at normal engine operating speeds. The mounting for the sensorsdiffer from each other to keep them from being interchanged.
7/22/2019 Electrical M07 Sensors en TXT
17/28
Caterpillar: Confidential Yellow
SERV1877 - 03/10 Module 7 - Switches/Sensors/Solenoids-17-
Although the sensors have an optimum operating range, the ECU will use the signalfrom the remaining sensor as a backup in case of a failure.
A magnetic pickup may be checked for both static and dynamic operation. With thepickup disconnected from the machine electrical harness, a resistance reading of thepickup coil (measured between pins) should indicate a coil resistance referenced in
the specifications. The resistance value differs between pickup types, but an infiniteresistance measurement would indicate an open coil, while a zero reading wouldindicate a shorted coil.
7/22/2019 Electrical M07 Sensors en TXT
18/28
Caterpillar: Confidential Yellow
SERV1877 - 03/10 Module 7 - Switches/Sensors/Solenoids-18-
ower speed sensitivity; muchmore accurate than mag pickup
type
all are three-wire ( ctive)
Dependent on metal passingthough a magnetic field
requency (hz) varies
Duty constant
Square wave signal
voltage may change some butis a signal carrier, not the mainsignal to be measured
ACTIVE SPEED SENSORS
- Two, Three, or Four-Wire
- Hall-Effect
18_1 18_2
Engine ECU
SPEED SENSOR CIRCUIT
J1
DMM MEASUREMENTS+V SensorSupply
Sensor Ground
Return
11 OR 18 A
BR 18 B
YL 18 C
12
OR 18
BK 18
YL 18
+V
Ground
Signal
Engine
Speed
Sensor
-Volts
- FrequencyEngine Speed 62
18_3 18_4
Some Caterpillar electronic systems use a Hall-Effect sensor for detecting magneticfields. The electronic transmission control uses this type of sensor to determine
transmission output speed, and the electronic unit injection system uses this type ofsensor to provide pulse signals for determining the speed and timing of the engine.
Both sensor types have a Hall cell (sensing element) located in the tip of the sensor.As a gear tooth passes the Hall cell, the change in the magnetic field produces a
small signal. The internal electronics of the sensor process the signal and sends adigital signal to the ECU.
The sensing element is extremely accurate because it is not speed dependent. Thesensing element operates down to 0 rpm over a wide temperature operating range.
7/22/2019 Electrical M07 Sensors en TXT
19/28
Caterpillar: Confidential Yellow
SERV1877 - 03/10 Module 7 - Switches/Sensors/Solenoids-19-
19_1
The timing measurement function of a speed/timing sensor uses a change in themagnetic field as a gear tooth passes to determine a tooth edge. A unique tooth
pattern on the timing wheel allows the ECU to determine crankshaft position, directionof rotation, and rpm. The ECU counts each pulse and determines speed, memorizesthe pattern (unique tooth pattern) of the pulses, and compares that pattern to adesigned standard to determine crankshaft position and direction of rotation.
This view shows a timing wheel and sensor. As each square gear tooth (arrow)passes the cell, the sensing element generates a small signal. If the signal is belowaverage (gap), the output will be low. If the signal is above average (tooth undercell), the output will be high.
7/22/2019 Electrical M07 Sensors en TXT
20/28
Caterpillar: Confidential Yellow
SERV1877 - 03/10 -20- Module 7 - Switches/Sensors/Solenoids
20_1
temperature Sensors
Temperature sensors measure the temperature of coolant, oil, intake air, fuel,exhaust, etc. Temperature sensors can be active (three-wire) or passive (two-wire).
This sensor includes a temperature-sensitive variable resistor (thermistor). Thevoltage drops of passive sensors and the voltage output of active analog sensorscorrelate to a specific temperature. On this type of temperature sensor, the signal(DC Volts) can be checked with power ON. The sensor resistance of passive sensorscan be checked with power OFF.
Active digital temperature sensors also use a thermistor that is sensitive to changesin temperature. The circuitry inside the sensor body converts the analog output ofthe thermistor to a PWM signal, which is sent to the ECU.
7/22/2019 Electrical M07 Sensors en TXT
21/28
Caterpillar: Confidential Yellow
SERV1877 - 03/10 Module 7 - Switches/Sensors/Solenoids-21-
21_1
pressure Sensors
Pressure sensors are used to measure pressures of oil, fuel, intake manifold (boost),atmosphere, crankcase, injection actuation, etc. Most pressure sensors found onCat equipment are active (three-wire) analog sensors.
Pressure sensors contain a strain gauge which changes resistance when a pressureis applied to it. The sensor circuitry detects this change in resistance and outputs avoltage in accordance with this resistance. The voltage output of a pressure sensorcorrelates to a specific pressure.
7/22/2019 Electrical M07 Sensors en TXT
22/28
7/22/2019 Electrical M07 Sensors en TXT
23/28
Caterpillar: Confidential Yellow
SERV1877 - 03/10 Module 7 - Switches/Sensors/Solenoids-23-
23_1
Magnetostrictive position Sensor
A magnetostrictive position sensor is shown in the above photo. This type of positionsensor provides a PWM signal to the ECU, indicating cylinder position.
In a magnetostrictive sensor, a pulse is induced in a specially-designedmagnetostrictive wave guide by the momentary interaction of two magnetic fields.The magnetostrictive principle is defined as a change in resistance when a magneticfield is applied perpendicular to the current flow in a thin strip of ferrous material.
7/22/2019 Electrical M07 Sensors en TXT
24/28
Caterpillar: Confidential Yellow
SERV1877 - 03/10 Module 7 - Switches/Sensors/Solenoids-24-
24_1
In magnetostrictive sensors, a thin piece of wire (wave guide) is placed inside aprotective tube. The wave guide transmits the input and output signals. An electronic
current (input) pulse from the sensor electronic assembly creates a magnetic fieldaround the protective tube. The magnetic field interacts with the position magnetsmagnetic field and causes the wave guide to twist. This twist is the return signal thatis sent back to the sensor electronics at a sonic speed along the wave guide.
The position of the moving magnet is precisely determined by measuring the elapsedtime between the release of the electronic pulse and the arrival of the return signal(wave guide twist).
7/22/2019 Electrical M07 Sensors en TXT
25/28
Caterpillar: Confidential Yellow
SERV1877 - 03/10 Module 7 - Switches/Sensors/Solenoids-25-
25_1
level Sensors
A level sender assembly is located in the top or side of a tank and measures thedepth of fuel or oil in the tank.
The depth of liquid in the tank determines the position of a float. This float will beattached to a lever or a spiral rod. The float will cause the lever to move up or down,or the float will travel up or down the spiral rod, rotating the rod as it moves. Thesender is attached to the lever or rod, and changes resistances as the lever movesup and down, or as the rod rotates. This resistance is measured by the ECU or amechanical gauge.
7/22/2019 Electrical M07 Sensors en TXT
26/28
Caterpillar: Confidential Yellow
SERV1877 - 03/10 Module 7 - Switches/Sensors/Solenoids-26-
26_1
Some Cat machines are equipped with an ultrasonic level sensor. This type of sensoris used on fuel systems and replaces older types of sensors that used a resistive
sending unit inside the fuel tank.
The ultrasonic fuel level reacts to the level of fuel in the tank. The sensor emits anultrasonic signal that travels up a guide tube in the tank. The signal is reflected off ofa metal disk on the bottom of a float that rides on the fuel and is directed back to thesensor. The sensor measures the amount of time it takes for the signal to leave thesensor, reflect off the disk, and return to the sensor.
The sensor has four contacts. The open or grounded status of contact three on theconnector tells the ECU whether the sensor is installed in a deep tank or a shallowtank. Contact three should be open for a deep tank and grounded for a shallowtank.
Troubleshooting procedures for the ultrasonic sensor would be the same as thoseused for other PWM sensors. The ultrasonic sensor must be installed in a fuel tankto be tested.
7/22/2019 Electrical M07 Sensors en TXT
27/28
Caterpillar: Confidential Yellow
SERV1877 - 03/10 Module 7 - Switches/Sensors/Solenoids-27-
lthough voltage is typicallythe measured parameterfor troubleshooting, currentperforms the work.
simple compass may alsobe used to check for electricalfunctionality of a solenoid, aswell as checking the resistanceof the coil and comparing it tospecifications.
27_1
Solenoids
Many Caterpillar electronic control systems use solenoids to perform a controlfunction. Some examples are shifting the transmission, raising an implement, fuelinjection, etc.
Solenoids are electronic devices that work on the principle of an electrical currentpassing through a conductive coil, thereby producing a magnetic field. This magnetic
field can be used to perform work, typically moving an internal spool. The type ofsolenoid that is used is determined by the task that is to be performed. Thetransmission shift solenoids in the above photo divert oil when the spools are movedby their respective magnetic field.
Solenoid valves in Cat equipment are either two-state (ON/OFF), or variable (PWM).Two-state solenoids actuate with a constant voltage, usually +12 or +24 VDC.Variable solenoids actuate using a PWM current. The less current needed, the lowerthe duty cycle of the source voltage. As more current is needed, the duty cycle isincreased.
To quickly check if a solenoid is energizing, set a screwdriver on the coil nut. If thecoil is energized, the screwdriver blade will be attracted to the nut by the coil smagnetic field.
7/22/2019 Electrical M07 Sensors en TXT
28/28
SERV1877 - 03/10 Module 7 - Switches/Sensors/Solenoids-28-
he red dashed line shows thebaseline current versuspressure for a solenoid valveused in the lectro- ydraulicImplement System. he areabetween the two solid lines is theacceptable tolerance bands forsolenoid valve performance.
600
500
400
300
200
100
0
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
Solenoid Current (Amps)
28_1
PWM solenoids receive a varying PWM current from their respective ECU. A fault isrecorded if the ECU senses the signal to the actuator solenoid as open, shorted to
ground, or shorted to battery.
The above graph shows the relationship between the current sent by the ImplementECU to the pilot actuator solenoids and the resulting pilot pressure.