Post on 06-Apr-2018
8/3/2019 Dome Camera
1/13
PTZ Dome Camera Product Instructions
Version 1.3
AC220V
AC24V
Please READ the instructions carefully before using this product
8/3/2019 Dome Camera
2/13
Index
I. Safety warning
II. Features..
. Brief resume.....
. Outlet Diagrams...
V. Setting the coding switch...
. Function description.
. Technical parameters....
. Installation guide...
.Troubleshooting...
8/3/2019 Dome Camera
3/13
Safety Warning:
Exclamatory Mark caution sign. Is used to remind user to operate carefully in this step,
and we should refer to the interrelated service information at this time.
noticenoticenoticenotice
Dangerous when Touch electricity
Do not disassemble by yourself
noticeIn order to prevent you from electric shock and damage of the mechanism,
Please DO NOT disassemble the product by yourself. This problem should besettled by the specialized engineer authorized by the manufacturer.
!
Lightning caution sign. Its used to remind user that there
is dangerous voltage nearby which can make electric
shock.
!
8/3/2019 Dome Camera
4/13
. ATTENTION
1. Please READ the instructions carefully before using this product.2. Dont use it under the conditions of too cold or hot.3. Dont use it under the conditions of too humid or dusty.4. To avoid you and machine being damaged, dont install the unit on an unfixed bracket.5.
To avoid short circuit, please ensure foreign objects are kept away from the machine.
6. Dont hit or shock the machine.7. Please cut off the power before cleaning. Dont use caustic liquid when clean it.8. Please connect the polarity of the power and communication wire correctly.9. To avoid the destruction of the camera CCD, dont aim the camera lens directly at sunlight or other light
objects.
10. Please ensure that you observe the relevant electrical safety standards when connecting the wires, andconfirm the type of the power adapter, there are two specifications of AC24 and AC220 for this product.
Please keep enough distance between the signal of RS-485 & video and high voltage resources, and
anti-lightning, anti-mouse.
11. You should cut off the power at once if there is a peculiar smell or smoking.12. When there is something wrong with machine, Please DO NOT dismantles the product by your self. This
problem should be settled by the specialized engineer authorized by the manufacturer or retailer.
. FEATURES
Long life, little interference, high reliability
Fine-looking
Available in horizontal limit
High capability and low price
Low power consumption, small bulk
Easy wiring
. BRIEF RESUME
This machine integrates multi protocols and available Baud rate. Perfect function design, mature technology,
decoder inside, I2C memory & RS485 remote communication technology used, which make it the best choice in
the area of CCTV.
Technology features:
1. The power supply uses switching power technology, which has high efficiency and a wide range of voltage,so it is applicable for the place of more Fluctuations in power grids in Monitoring Project.
2. In order to improve the reliability of the dome camera, we mostly use chip components, optical isolationdevice, semiconductor devices.
3. The signal of RS-485 & video use TVS technology, which can effectively avoid the damage caused bylightning, surge and so on.
4. We use power chip drives in the control of the camera so that the maximum output current can be up to200mA.
8/3/2019 Dome Camera
5/13
. OUTLET DIAGRAMS
The outlet of the dome camera is as follows:
(Figure 1)
....SETTING OF THE CODING SWITCH
1. The system topology drawing1) The system connection drawing
8/3/2019 Dome Camera
6/13
(Figure 2)
2) Address/protocol coding drawingAs shown in Figure3, there is a 6-bit and a 10-bit coding switch, which is used to set the protocol , the band rate
and the address of the dome camera.
(Figure 3)
2. Selection of the protocol of communicationAs shown in Figure3, U3 is used to set the protocol of communication and the band rate, the protocol is selected
from DIP-4 to DIP-1. The chart of coding switches is as follows:
3. selection of the protocol ofcommunicationType of protocol
DIP-1 DIP-2 DIP-3 DIP-4
B01 ON OFF OFF OFF
PELCO-D ON ON OFF OFF
PELCO-P OFF OFF ON OFF
8/3/2019 Dome Camera
7/13
4. DIP-5 and DIP-6 of U3 are used to set the band rate of communication, there are four different band ratescan be selected as follows:
Band rate setCommunication
band rate DIP-1 DIP-2 DIP-3 DIP-4 DIP-5 DIP-62400bps OFF OFF
4800bps ON OFF
9600bps OFF ON
19200bps ON ON
For example:
(Figure 4)
5. Setting of the address of machine1) Set the correct address before using the unit.2) The address code can be set by DIP-1 to DIP-10 of U4, the setting adopts the rule of the Binary 8421 code.
DIP-10 stand for the highest digit, DIP-1 stand for the lowest digit, the biggest address code is 1023, 1means the state ON and 0means the state OFF, details as following:
DIP1 DIP2 DIP3 DIP4 DIP5 DIP6 DIP7 DIP8 DIP9 DIP10
0 OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
1 ON OFF OFF OFF OFF OFF OFF OFF OFF OFF
2 OFF ON OFF OFF OFF OFF OFF OFF OFF OFF
3 ON ON OFF OFF OFF OFF OFF OFF OFF OFF
8/3/2019 Dome Camera
8/13
4 OFF OFF ON OFF OFF OFF OFF OFF OFF OFF
5 ON OFF ON OFF OFF OFF OFF OFF OFF OFF
6 OFF ON ON OFF OFF OFF OFF OFF OFF OFF
7 ON ON ON OFF OFF OFF OFF OFF OFF OFF
8 OFF OFF OFF ON OFF OFF OFF OFF OFF OFF
9 ON OFF OFF ON OFF OFF OFF OFF OFF OFF10 OFF ON OFF ON OFF OFF OFF OFF OFF OFF
11 ON ON OFF ON OFF OFF OFF OFF OFF OFF
12 OFF OFF ON ON OFF OFF OFF OFF OFF OFF
13 ON OFF ON ON OFF OFF OFF OFF OFF OFF
14 OFF ON ON ON OFF OFF OFF OFF OFF OFF
15 ON ON ON ON OFF OFF OFF OFF OFF OFF
16 OFF OFF OFF OFF ON OFF OFF OFF OFF OFF
OFF
1023 ON ON ON ON ON ON ON ON ON ON
2) Setting of the Ending Resistor
Connect the ending resistor to both ends of the RS-485 bus, and do not connect it in other nodes. There are three
pins JP-1, as shown in figure 5. The standard of RS-485 bus requests the device be connected by the way of
daisy chain, so you must connect the 120 resistor in terminal, as shown in figure 6.(notice: D stands for the
maximum distance of 7 meters)
(Figure 5)
(Figure 6)
....FUNCTION DESCRIPTION
1. the control of the lens1) The dome camera controls the zoom, focus, iris of the camera through the voltage. When the camera
receives the command of tele and near, it outputs positive voltage, then, when the camera receives the
command of wide and far, it outputs negative voltage. Conversely, please reverse connection.2) The output of the control voltage: +DC12V.
8/3/2019 Dome Camera
9/13
(Figure 7)
.TECHINICAL PARAMETERS
Input voltage AC24V10% 50/60HZ
AC220V10% 50/60HZ(anyone available)
Input power Inside12W outside30W
The band rate 2400bps4800bps9600bps19200bps(anyone available)The range of address 0511
Means of communication RS-485
Protocol of communication Multi protocol available
The range of rotate Level0355 Vertical090
Limit of rotate Level
Speed of rotate Level8/s2% Vertical12/s2%
Available temperature Inside045 Outside-3555
Installation size 112mm(L) 60mm(W) 70mm(H)
....INSTALLATION GUIDEINSTALLATION GUIDEINSTALLATION GUIDEINSTALLATION GUIDE
1.Installation requirements:
1) Electric power supply: You should select the suitable wire size and transmission distance, so that you canmeet your power requirements.
2) Installation: for safety, please ensure the surface the camera is mounted is able to handle the total productweight.
8/3/2019 Dome Camera
10/13
2.Installation size:
1) Internal wall hanging installation
(Figure 8)
2) Internal ceiling hanging installation
(Figure 9)
3.Bracket installation
1) Wall hanging bracket installation:The installation wall should be solid and not come off.
Confirm the bracket is installed on a solid wall and not on the outer covering.
If the protocol or band rate or dome address needs to be adjusted, please refer to Figure3 .
Steps of installation:
a) Select a suitable place on the solid wall, take the wall hanging bracket and draw a center place of fixedinstallation hole with pencil on surface.
b) Drill 4 installation holes for the M8 metal bolts with a drill, then assemble the M8 bolt.(Figure 10)
8/3/2019 Dome Camera
11/13
c) Fix the bracket on the wall with 4 M8 bolts and gaskets.
(Figure 10)
2) Ceiling hanging bracket installation:a) Select a suitable place on a solid wall, take the ceiling hanging bracket and draw a center place for fixed
installation hole with a pencil on the surface.(Figure11)
b) Drill 4 installation holes for the M8 bolts using an electric drill, then assemble the M8 bolt.c) Fix the ceiling hanging bracket on the ceiling as shown Figure 12.
(Figure 11) (Figure 12)
4. The dome camera and bracket installation:
a) Take out the dome from package
b) Put the combination wire through the bracket
c) Rotate the dome to the bracket according to the direction of arrow
d) Fix the dome transparent cover through tightening bolt. (Figure13)
8/3/2019 Dome Camera
12/13
(Figure 13)
5. Transparent dome cover installation:
a) Aim the interface of transparent dome cover at the one of outer cover of the dome.
b) Rotate the dome to the bracket according to the direction of arrow, till outer cover tallies with transparent
dome cover (Figure14)
(Figure 14)
6. Remove the locknut
Before using the dome, please remove the locknut, which fix the dome so as to prevent it from shocking
during transport.
8/3/2019 Dome Camera
13/13
(Figure 15)
....TROUBLESHOOTING
Problem cause solution
Bad connection Check all connections to the camera
Dome ID is unavailable Select ID again
Dome can not be controlled Protocol or band rate
is unmatched
Adjust protocol ,control match and
on power again
Video line is bad RemoveVague image
Power supply is not enough Replace
Bad connection of control Reconnect the control
Bad control Power off/on again
Lost control of domeToo much load or communication
away distance too far
1. The ending resistance of the
farthest dome from controller should
be on the state of on, others is
off.
2. Add the code distributors