Designed by Steve GoodDigital Patterns

Hundreds of free PatternsStencil PrinterJigsaw Puzzle TemplatesDVD’sKey Chain Pattern PrinterVideo TutorialsReviewsCommunity Forum and more.

If you enjoy thispattern I amasking $5.

Note to commercial print employees: I give my permission to print as many of this pattern book as your customer requires.

steve@stevedgood.com Copyright Steve Good 2017

Note to commercial print employees: I give my permission to print as many of this pattern book as your customer requires.

steve@stevedgood.com Copyright Steve Good 2017

$5.00

General Pattern InformationYou may use this pattern to make as many of the project as you like. You are free to use any technique including mass production to build the project. The pattern may be copied and

given to others provided the entire book is kept intact. You may not sell the pattern or include it

in another commercial package of any type.

Steve Good retains the right to the pattern. If you have any questions about the use of this

pattern please contact me at steve@stevedgood.com

Printing InstructionsWhen printing this pattern it is important to print it full size. When you bring up the print dialog

box look in the “Page Sizing & Handling” section. Make sure the “Actual Size” is selected

before you hit print.

You also only need to print the page/s you need. After the print dialog opens look for the

“Pages to Print” section. You can print the current page or a range of pages. This will help

save ink by not printing the title/instruction pages.

14 piece lighted nativity project.

The figures are approximately 5.5 inches tall.

The palm tree stands over 9 inches tall.

The pattern calls for 1/2” thick boards for the manger.Home Depot sells laminated spruce boards that workgreat for this project. The boards are 1” X 16” X 48”. Theactual thickness is .6 inches thick. They are cheap at$12.82 per board. This is what I used. You can also justglue up your own panels if you have that available.

If you want to light the manger you needa lighting kit that fits a 1” hole. Theseare available at any good craft orhardware store.

Manger

The next few pages show the completed piece of each patternYou can study these pictures if you need an assembly guide.

Palm Tree

The project is cut mostly from 1/4” Thick wood.The camel body is 1/2” thick.

Baby Jesus

Mary

Joseph

Angel

King 1

King 2

King 3

Camel

Donkey

Lamb

Dog

Little Shepard Boy

Joseph

1/4” Thick

Tab A

Slot A

On all figures the tab fitsin to the slot of the base.

Look at the included picturesfor part placement beforeglueing.

Mary

1/4” Thick

Baby Jesus

1/4” Thick

King 1

1/4” Thick

King 2

1/4” Thick

King 3

1/4” Thick

Angel

1/4” Thick

Shepard Boy

1/4” Thick

Dog

1/4” Thick

Donkey1/4” Thick

Lambs1/4” Thick

Camel

1/2” Thick

1/4” Thick

Extra space to add strength. Place it betweenthe base of both leg sets.

1/4” Thick

1/4” Thick

Manger Left Front

1/2” Thick

Tape with the next page at the dotted lineto make the complete pattern

Manger Right

Manger Left Back

1/2” Thick

Tape with the next page at the dotted lineto make the complete pattern

1 inch hole forlighting kit.

Manger back Right

Manger Left Wall1/2” Thick

Manger Right Wall1.2” Thick

1/4” Thick

Palm Tree part 1

Palm Tree Part 2

1/4” Thick

Palm Tree Base1/4” Thick

The roof are 1/8” X 1.5” X 8” strips. I ripped a constructiongrade 2 X 4 in 1/8” thick strips and cross cut them

8 inches long. You need 10 strips. You could probablyuse 1/4” Thick strips if that’s what you have available.

You could also cover with 1/4” thick solid panelsfor easier assembly

I glued and nailed the strips with small brad nails.

The base is optional. It is 22” X 16”. I used the same spruce laminated panel I made the manger from to cut the base.