Post on 19-Jul-2022
Index
® Buick, Chevrolet and GMC are registered trademarks and property of their respective companies.
Vehicle Application Guide.....................................................................................................................................................................
Key2GO...............................................................................................................................................................................................
Installation (Wiring Diagrams & Vehicle Wiring Reference Charts)Type 1a.................................................................................................................................................................................................Type 1b.................................................................................................................................................................................................Type 1c.................................................................................................................................................................................................Type 2a.................................................................................................................................................................................................Type 2b.................................................................................................................................................................................................Type 2c.................................................................................................................................................................................................Type 3..................................................................................................................................................................................................SmartStart/XL202 Installation Notes....................................................................................................................................................
ProgrammingModule Programming...........................................................................................................................................................................Module Reset.......................................................................................................................................................................................Hard Reset...........................................................................................................................................................................................Feature & Option List...........................................................................................................................................................................Feature Programming..........................................................................................................................................................................
LED Diagnostics & Troubleshooting....................................................................................................................................................
Limited One-Year Consumer Warranty.................................................................................................................................................
Quick Reference Guide........................................................................................................................................................................
02
03
0405061112131618
1921212223
24
26
27
Installation Guide
Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product.
This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode with or without a Plug & Play THGM610/THGM610D T-Harness (optional). This solution offers three (3) configuration options to control your system: 3x OEM Lock Remote Start Activation, RF Kit or SmartStart (all sold separately). Refer to section for SmartStart and XL202 installation.
Refer to Quick Reference Guide (QRG) at the end of this guide for more information on how to use the various features offered with this product.
Using this product without RF Kit is not recommended since the factory remote is disabled during run time.
Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance.
Important:
This guide is compatible with the GM10 firmware version 4.03 and later.
This product is NOT compatible with vehicles equipped with a manual transmission.
SmartStart CompatibleSmartStart is equipped with D2D, which means it can be connected to an interface module and used in Remote Start Ready (RSR) mode without the use of a remote starter. See the Module Programming section for more information.
Rev.: 20170412
Platform: DBALL/DBALL2Firmware: GM10 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Vehicle Application GuidePage 2
The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle.
[2] T-Harness THGM610/THGM610D is ONLY compatible with these models IF the vehicle is equipped with OnStar.
[1] T-Harness THGM610/THGM610D is not compatible with 2013-2015 Chevrolet Spark.
Vehicles
2017
2016
2015
2014
2013
2012
2011
2010
PK
-Im
mobilizer
Bypass-D
ata
No
Key
Req'd
CC
-Heate
dS
eats
Activ
atio
n
CC
-Pow
er
win
dow
sR
olld
ow
n
CC
-Pow
er
win
dow
sR
ollu
p
DL-A
rmF
acto
ryS
ecurity
DL-D
isarm
Facto
ryS
ecurity
DL-D
oor
Lock
Contr
ol
DL-D
oor
Unlo
ck
DL-D
river
Priority
Unlo
ck
Key2G
O
RS
-3x
LO
CK
ST
AR
T(S
tart
contr
olu
sin
gO
EM
Rem
ote
)
RS
-3x
LO
CK
ST
OP
(Sto
pcontr
olu
sin
gO
EM
Rem
ote
)
RS
-RA
PS
hutD
ow
n(R
eta
ined
AC
CP
ow
er)
RS
-Rem
ote
Sta
rtR
eady
RS
-Sm
art
Sta
rt
RS
-Tach
/R
PM
Outp
ut
SS
-Entr
yM
onito
ring
ALL
Door
Pin
s
SS
-Entr
yM
onito
ring
Driver
Door
Pin
SS
-Entr
yM
onito
ring
Hood
Pin
SS
-Entr
yM
onito
ring
Tru
nk/H
atc
hP
in
ST
-Bra
ke
Sta
tus
(footbra
ke)
Buick
Encore 1 1 1 1 • • • • • • • • • D D • • • • • •
LaCrosse 1 1 1 1 1 1 1 • • • • • • • • • D D • • • • • •
Regal 1 1 1 1 1 • • • • • • • • • D D • • • • • •
Verano 1 1 1 1 1 1 • • • • • • • • • D D • • • • • •
Chevrolet
Camaro 1 1 1 1 • • • • • • • • • • • • D D • • • • • •
Camaro 1 1 • • • • • • • • • D D • • • • • •
Colorado 2 2 • • • • • • • • • • • • D D • • • • •
Cruze 1 1 1 1 1 1 1 • • • • • • • • • D D • • • • • •
Cruze Limited 1 • • • • • • • • • D D • • • • • •
Equinox 1 1 1 1 1 1 • • • • • • • • • • • • D D • • • • • •
Equinox 1 1 • • • • • • • • • D D • • • • • •
Impala 1 1 1 • • • • • • • • • D D • • • • • •
Impala Limited 1 1 1 • • • • • • • • • D D • • • • • •
Malibu 1 1 1 • • • • • • • • • D D • • • • • •
Malibu Limited 1 • • • • • • • • • D D • • • • • •
Orlando 1 1 • • • • • • • • • D D • • • • • •
Silverado 1500 [2] 2 2 2 • • • • • • • • • • D D • • • • • •
Silverado 2500/3500 [2] 2 2 • • • • • • • • • • D D • • • • • •
Sonic 1 1 1 1 1 • • • • • • • • • D D • • • • • •
Spark [1] 2 3 3 3 • • • • • • • • • D D • • • • • •
Suburban 2 • • • • • • • • • • D D • • • • • •
Tahoe 2 • • • • • • • • • • D D • • • • • •
Trax 1 1 1 1 • • • • • • • • • D D • • • • • •
GMC
Canyon 2 2 • • • • • • • • • • • • D D • • • • • •
Sierra 1500 [2] 2 2 2 • • • • • • • • • • D D • • • • • •
Sierra 2500/3500 [2] 2 2 • • • • • • • • • • D D • • • • • •
Terrain 1 1 1 1 1 1 • • • • • • • • • • • • D D • • • • • •
Terrain 1 1 • • • • • • • • • D D • • • • • •
Yukon 2 • • • • • • • • • • D D • • • • • •
Legend:
CC: Comfort & Convenience Controls RS: Remote Start & Engine Controls
DL: OE Door Lock & Alarm Controls SS: Integrated Security & Monitoring
FOB: Sync CAN Interface w/FOB Remote ST: Function/Feature Status
PK: Transponder & Immobilizer Override
Rev.: 20170412
Platform: DBALL/DBALL2Firmware: GM10 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Rev.: 20170412
Platform: DBALL/DBALL2Firmware: GM10 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Page 3
This feature is required if only one key is available. You can program the interface without the need for Key2Go if two keys are present.
Key2GO has been designed and developed to bypass the advanced encryption layers found in modern vehicles. It uses an array of servers to generate a duplicate of the original key, allowing the installation of a remote starter without having to give up a key.
The advantage is that this feature allows you to use one original key and the server to configure the bypass in the vehicle.
All Key2GO-compatible firmware are clearly indicated in the function list of each vehicle search result page and will also appear on the flash page. Any first-time user must re-register to gain access to Key2GO, and some additional information will be required to complete the registration process, such as your Directed account number and store name. Key2GO requires an XKLoader.
Refer to page 20 of this guide for instructions on how to program features using Key2GO.
Important!The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
Refer to the Vehicle Wiring Reference Chart for more information on specific wiring and connections.
SW CAN: Green, pin 1
HS CAN High: Tan/Black or Blue, pin 6
(-) Ground: Black, pin 4
HS CAN Low: Tan or White,
pin 14
(+) 12V: pin 16
OBDIIDiagnostic Connector
321
ImmobilizerControl Module (black conn. under
ignition switch)
Cut
(-) Driver Door Input [1]
1 8
169
Single Wire CAN: Light Green: 1
(+) Ignition Output: Yellow: 8
(+) 12V Ignition Input: Brown: 7
Immo. Data Interr. (veh. side): Yellow/Red: 11
(+) 12V: Red: 13
(-) Ground: Black: 14
Immo. Data Interr. (conn. side): Orange/Red: 10
[1] (-) RAP Off Output: Green/Black: 2
(-) Parking Light Output: Black/White: 1
Immo. Data (veh. side): Orange/Black: 11
(+) Accessory Output: Gray/Black: 7
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
654321
(+) Ignition: pin 1
(+) Accessory: pin 3
Headlight Switch (black 12-pin conn.)
1 2 3 4 5
7
6
121198 10
(-) Parking Lights: pin 3
Ignition Switch(black or white 6-pin conn.)
Immo. Data: pin 2
6: White/Black: (-) Hood
Hood Pin
Remote Start Safety Override Switch
Note: Hood pin only required on vehicles not equipped with a factory hood pin.
Type 1a (Without T-Harness)Page 4
[1] If the RAP Off wire is not connected, the radio will turn OFF but some lights will remain ON in the center console for 10 minutes. Connect the Green/Black, pin 2/12 to the vehicle driver door input to avoid the issue.
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
14
12
2
10
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
DBALL/DBALL2
RF
Prog. Button
LED
4
Rev.: 20170412
Platform: DBALL/DBALL2Firmware: GM10 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
To vehicle 6-pin connector
Ignition 6-pin connector
Use connectors labeled GM10
[1] (-) RAP Off Output: Green/Black
(-) Parking Light Output:Black/White
(-) Driver Door Input [1]
N/A: Violet/Green
N/A: Violet/Brown
N/A:Pink
Remote Start Safety Override Switch
Hood Pin
Note: hood pin only required on vehicles not equipped with a factory hood pin
Wh
ite/B
lack
T-HarnessTHGM610(Optional)
Ignition Barrel
Cut away the 4-pin connector and connect the three wires to the OBDII 16-pin connector.
1 8
169
HS CAN High: Tan/Black or Blue, pin 6
Tan
/Bla
ck
HS CAN Low: Tan or White, pin 14
Tan
SW CAN: Green, pin 1
Lt. G
reen
Away from Immobilizer
Control Module
(vehicle side)
GM10 GM10
T-01
GM06
NOT USED
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
To Immobilizer Control Moduleunder ignition switch(black 3-pin connector)
Headlight Switch
(white 12-pin conn.)1 2 3 4 5
7
6
121198 10
T-02
NOT USED
(-) Parking Lights: pin 3
T-01
Buick Encore
Buick LaCrosse
Buick Regal
Buick Verano
Chevrolet Camaro
Chevrolet Cruze
Chevrolet Equinox
Chevrolet Impala
Chevrolet Malibu
Chevrolet Orlando
Chevrolet Sonic
Chevrolet Trax
GMC Terrain
Refer to the Vehicle Wiring Reference Chart for more information on specific wiring and connections.
OBDIIDiagnostic Connector
Type 1b (With T-Harness - THGM610 Rev. 1)Page 5
14
12
[1] If the RAP Off wire is not connected, the radio will turn OFF but some lights will remain ON in the center console for 10 minutes. Connect the Green/Black, to the driver door input to avoid the issue.
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
14
12
2
10
DBALL/DBALL2
RF
Prog. Button
LED
4
Rev.: 20170412
Platform: DBALL/DBALL2Firmware: GM10 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Ignition Barrel
(-) Parking Lights Output:Black/White
To vehicle 6-pin connector
To Ignition 6-pin connector
To Immobilizer Control Moduleunder ignition switch(black 3-pin connector)
NOT USED
(-) Driver Door Input [1]
N/A: Pink
T-HarnessTHGM610/THGM610D(Optional)
GM10
GM06
GM10
T-01
Use connectors labeled GM10.
Away from Immobilizer Control Module (ICM)(vehicle side)
[1] RAP Off Green/Black
Diagnostic ConnectorOBDII (connector side view)
1 8
169
CAN High: Tan/Black or Blue, pin 6
CAN Low: Tan or White, pin 14
SW CAN: Green, pin 1
Lt.G
ree
n
Tan
Tan
/Bla
ck
T-02NOT USED
Headlight Switch(white 12-pin)
1 2 3 4 5
7
6
121198 10
(-) Parking Lights:pin 3
T-01
Buick Encore
Buick LaCrosse
Buick Regal
Buick Verano
Chevrolet Camaro
Chevrolet Cruze
Chevrolet Equinox
Chevrolet Impala
Chevrolet Malibu
Chevrolet Orlando
Chevrolet Sonic
Chevrolet Trax
GMC Terrain
Cut away the 4-pin connector and connect the three wires to the OBDII 16-pin connector.
Refer to the Wiring Reference Chart for more information on specific wiring and connections.
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
Remote Start Safety Override Switch
Hood Pin
Note: hood pin only required on vehicles not equipped with a factory hood pin
Wh
ite/B
lack
Type 1c - (With T-Harness - Rev. 2 & 3)Page 6
[1] If the RAP Off wire is not connected, the radio will turn OFF but some lights will remain ON in the center console for 10 minutes. Connect the Green/Black) to the driver door input to avoid the issue. RAP Off/Door Input color and location can be found in the Vehicle Wiring Reference Charts.
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
10
DBALL/DBALL2
RF
Prog. Button
LED
4
14
12
2
Rev.: 20170412
Platform: DBALL/DBALL2Firmware: GM10 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Rev.: 20170412
Platform: DBALL/DBALL2Firmware: GM10 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Page 7
Wire colors should only be used as a reference. You should always test a wire's function and pin location before connecting to it.
Vehicle Wiring Reference Chart - Type 1
Function Color Pin Polarity Location Color Pins
Ignition Violet/ Black 1 (+) Ignition Control Switch Black 6
Accessory Violet/Yellow 3 (+) Ignition Control Switch Black 6
Parking Lights Green/Gray 3 (-) Headlight Switch Black 12
DATA Bypass Green/Violet 2 Data Immobilizer Control Module, under ignition switch Violet 3
RAP Off Gray 6 (-) Driver Window Motor, in driver's door Black 7
SW CAN Green 1 Data OBDII Black 16
CAN High Blue 6 Data OBDII Black 16
CAN Low White 14 Data OBDII Black 16
Ignition Pink 1 (+) Ignition Switch Black 6
Accessory Brown 3 (+) Ignition Switch Black 6
Parking Lights Lt. Blue 3 (-) Headlight Switch Black 12
Immo. Data Lt. Blue 2 Data Immo. Control Module, under Ignition Switch Violet 3
RAP Off Gray/Black 6 (-) Driver Window Motor Black 7
SW CAN Dk. Green 1 Data OBDII Connector Black 16
CAN High Tan/Black 6 Data OBDII Connector Black 16
CAN Low Tan 14 Data OBDII Connector Black 16
Ignition Violet 1 (+) Ignition Switch Black 6
Accessory Violet 3 (+) Ignition Switch Black 6
Parking Lights Lt. Green 3 (-) Headlight Switch Black 12
Immo. Data Green/Violet 2 Data Immo. Control Module, under Ignition Switch Violet 3
RAP Off Gray 6 (-) Driver Window Motor Black 7
SW CAN Green 1 Data OBDII Connector Black 16
CAN High Dk. Blue 6 Data OBDII Connector Black 16
CAN Low White 14 Data OBDII Connector Black 16
Ignition Violet/Black 1 (+) Ignition Switch Black 6
Accessory Violet/Yellow 3 (+) Ignition Switch Black 6
Parking Lights Green/Brown 3 (-) Headlight Switch Black 12
Immo. Data Green/Violet 2 Data Immo. Control Module, under Ignition Switch Violet 3
RAP Off Gray 6 (-) Driver Window Motor Black 7
SW CAN Green 1 Data OBDII Connector Black 16
CAN High Dk. Blue 6 Data OBDII Connector Black 16
CAN Low White 14 Data OBDII Connector Black 16
Ignition Violet 1 (+) Ignition Switch Black 6
Accessory Lt. Green 3 (+) Ignition Switch Black 6
Parking Lights Lt. Green 3 (-) Headlight Switch Black 12
Immo. Data Green/Violet 2 Data Immo. Control Module, under Ignition Switch Violet 3
RAP Off Gray 6 (-) Driver Window Motor Black 7
SW CAN Lt. Green 1 Data OBDII Connector Black 16
CAN High Dk. Blue 6 Data OBDII Connector Black 16
CAN Low White 14 Data OBDII Connector Black 16
Ignition Violet/Black 1 (+) Ignition Switch Black 6
Accessory Violet/Yellow 3 (+) Ignition Switch Black 6
Parking Lights Green/Gray 3 (-) Headlight Switch Black 12
Immo. Data Lt. Green/White or Green/Violet 2 Data Immo. Control Module, under Ignition Switch Violet 3
RAP Off Gray 6 (-) Driver Window Motor Black 7
SW CAN Green 1 Data OBDII Connector Black 16
CAN High Blue 6 Data OBDII Connector Black 16
CAN Low White 14 Data OBDII Connector Black 16
Buick LaCrosse 2013
Buick LaCrosse 2014-2016
Buick Regal 2011
Wire Information Connector Information
Buick Encore 2013-2016
Buick LaCrosse 2010
Buick LaCrosse 2011-2012
Rev.: 20170412
Platform: DBALL/DBALL2Firmware: GM10 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Page 8
Wire colors should only be used as a reference. You should always test a wire's function and pin location before connecting to it.
Vehicle Wiring Reference Chart - Type 1
Function Color Pin Polarity Location Color Pins
Immo. Data Green/Violet 2 Data Transponder Key Amplifier on ignition switch. Violet 3
Accessory Violet/Yellow 3 (+) Ignition switch. Black 6
Ignition Violet/Black 1 (+) Ignition switch. Black 6
Door Input/RAP Off Gray 6 (-) Driver window module in drivers door. Black 7
Parking Lights Green/Gray 3 (-) Headlight switch. Black 12
HS CAN High Blue 6 Data OBDII. Black 16
HS CAN Low White 14 Data OBDII. Black 16
SW CAN Green 1 Data OBDII. Black 16
12V Red/Yellow 4 (+) BCM, above driver kick panel. Blue 27
Clutch Yellow B MUX Clutch pedal switch. Black 3
Immo. Data Green/Violet 2 Data Transponder Key Amplifier on ignition switch. Violet 3
Accessory Violet/Yellow 3 (+) Ignition switch. Black 6
Ignition Violet/Black 1 (+) Ignition switch. Black 6
Door Input/RAP Off Gray 6 (-) Driver window module in drivers door. Black 7
Parking Lights Green/Gray 3 (-) Headlight switch. Black 12
HS CAN High Blue 6 Data OBDII. Black 16
HS CAN Low White 14 Data OBDII. Black 16
SW CAN Green 1 Data OBDII. Black 16
12V Red/Brown 4 (+) BCM, above driver kick panel. Blue 27
Clutch Yellow B MUX Clutch pedal switch. Black 3
Immo. Data Lt. Blue 2 Data Transponder Key Amplifier on ignition switch. Violet 3
Accessory Brown 3 (+) Ignition switch. Black 6
Ignition Pink 1 (+) Ignition switch. Black 6
Door Input/RAP Off Gray 6 (-) Driver window module in drivers door. Black 7
Parking Lights Lt. Blue 3 (-) Headlight switch. Black 12
HS CAN High Tan/Black 6 Data OBDII. Black 16
HS CAN Low Tan 14 Data OBDII. Black 16
SW CAN Dk. Green 1 Data OBDII. Black 16
12V Red/White 4 (+) BCM, above driver kick panel. Blue 27
Clutch Yellow B MUX Clutch pedal switch. Black 3
Immo. Data Green/Violet 2 Data Transponder Key Amplifier on ignition switch. Violet 3
Accessory Violet/Yellow 3 (+) Ignition switch. Black 6
Ignition Violet/Black 1 (+) Ignition switch. Black 6
Driver Window Switch (driver window auto down only). Black 8
Driver Window Motor (driver window auto up & down). Black 7
Parking Lights Green/Gray 3 (-) Headlight switch. Black 12
HS CAN High Blue 6 Data OBDII. Black 16
HS CAN Low White 14 Data OBDII. Black 16
SW CAN Green 1 Data OBDII. Black 16
12V Red/Gray 4 (+) BCM, above driver kick panel. Blue 27
Clutch Yellow B MUX Clutch pedal switch. Black 3
Immo. Data Green/Violet 2 Data Transponder Key Amplifier on ignition switch. Violet 3
Accessory Violet/Yellow 3 (+) Ignition switch. Black 6
Ignition Violet/Black 1 (+) Ignition switch. Black 6
Driver Window Switch (driver window auto down only). Black 8
Driver Window Motor (driver window auto up & down). Black 7
Parking Lights Green/Gray 3 (-) Headlight switch. Black 12
HS CAN High Blue 6 Data OBDII. Black 16
HS CAN Low White 14 Data OBDII. Black 16
SW CAN Green 1 Data OBDII. Black 16
12V Red/Gray 4 (+) BCM, above driver kick panel. Blue 27
Clutch Yellow B MUX Clutch pedal switch. Black 3
Connector Information
Chevrolet Camaro 2010-2015
Chevrolet Cruze 2011-2017
Chevrolet Cruze Limited 2016
Door Input/RAP Off Gray 6 (-)
Wire Information
Buick Regal 2012-2015
Buick Verano 2012-2017
Door Input/RAP Off Gray 6 (-)
Rev.: 20170412
Platform: DBALL/DBALL2Firmware: GM10 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Page 9
Wire colors should only be used as a reference. You should always test a wire's function and pin location before connecting to it.
Vehicle Wiring Reference Chart - Type 1
Function Color Pin Polarity Location Color Pins
Immo. Data Lt. Blue 2 Data Transponder Key Amplifier on ignition switch. Violet 3
Accessory Brown 3 (+) Ignition switch. Black 6
Ignition Pink 1 (+) Ignition switch. Black 6
Door Input/RAP Off Gray/Black 6 (-) Driver window module in drivers door. Black 8
Parking Lights Lt. Blue 3 (-) Headlight switch. Black 12
HS CAN High Tan/Black 6 Data OBDII. Black 16
HS CAN Low Tan 14 Data OBDII. Black 16
SW CAN Lt. Green 1 Data OBDII. Black 16
12V Red/Violet 4 (+) BCM, above driver kick panel. Blue 27
Immo. Data Green/Violet 2 Data Transponder Key Amplifier on ignition switch. Violet 3
Accessory Yellow 3 (+) Ignition switch. Black 6
Ignition Violet 1 (+) Ignition switch. Black 6
Door Input/RAP Off Gray 6 (-) Driver window module in drivers door. Black 7
Parking Lights Green/Gray 3 (-) Headlight switch. Black 12
HS CAN High Blue 6 Data OBDII. Black 16
HS CAN Low White 14 Data OBDII. Black 16
SW CAN Green 1 Data OBDII. Black 16
12V Red/Yellow 4 (+) BCM, above driver kick panel. Blue 27
Immo. Data Green/Violet 2 Data Transponder Key Amplifier on ignition switch. Violet 3
Accessory Yellow 3 (+) Ignition switch. Black 6
Ignition Violet 1 (+) Ignition switch. Black 6
Driver Window Switch (driver window auto down only) Black 8
Driver Window Motor (driver window auto up & down) Black 7
Parking Lights Gray 3 (-) Headlight switch. Black 12
HS CAN High Blue 6 Data OBDII. Black 16
HS CAN Low White 14 Data OBDII. Black 16
SW CAN Green 1 Data OBDII. Black 16
12V Red/Violet 4 (+) BCM, above driver kick panel. Blue 27
Immo. Data Green/Violet 2 Data Transponder Key Amplifier on ignition switch. Violet 3
Accessory Yellow 3 (+) Ignition switch. Black 6
Ignition Violet 1 (+) Ignition switch. Black 6
Driver Window Switch (driver window auto down only) Black 8
Driver Window Motor (driver window auto up & down) Black 7
Parking Lights Gray 3 (-) Headlight switch. Black 12
HS CAN High Blue 6 Data OBDII. Black 16
HS CAN Low White 14 Data OBDII. Black 16
SW CAN Green 1 Data OBDII. Black 16
12V Red/Violet 4 (+) BCM, above driver kick panel. Blue 27
Immo. Data Green/Violet 2 Data Transponder Key Amplifier on ignition switch. Violet 3
Accessory Violet/Yellow 3 (+) Ignition switch. Black 6
Ignition Violet/Black 1 (+) Ignition switch. Black 6
Door Input/RAP Off Gray 6 (-) Driver window module in drivers door. Black 7
Parking Lights Green/Gray 3 (-) Headlight switch. Black 12
HS CAN High Blue 6 Data OBDII. Black 16
HS CAN Low White 14 Data OBDII. Black 16
SW CAN Green 1 Data OBDII. Black 16
12V Red/Yellow 3 (+) BCM, above driver kick panel. White 26
Chevrolet Orlando 2012-2013
Door Input/RAP Off Gray 6 (-)
Door Input/RAP Off Gray
Chevrolet Impala 2014-2015
6 (-)
Wire Information Connector Information
Chevrolet Equinox 2010-2017
Chevrolet Malibu 2013-2016
Chevrolet Malibu Limited 2016
Rev.: 20170412
Platform: DBALL/DBALL2Firmware: GM10 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Wire colors should only be used as a reference. You should always test a wire's function and pin location before connecting to it.
Vehicle Wiring Reference Chart - Type 1Page 10
Function Color Pin Polarity Location Color Pins
Immo. Data Green/Violet 2 Data Transponder Key Amplifier on ignition switch. Violet 3Accessory Violet/Yellow 3 (+) Ignition switch. Black 6Ignition Violet/Black 1 (+) Ignition switch. Black 6
6 Driver window module (with power windows) Black 722 BCM, above driver kick panel (without power windows) Pink 27
Parking Lights Green/Gray 3 (-) Headlight switch. Black 12HS CAN High Blue 6 Data OBDII. Black 16HS CAN Low White 14 Data OBDII. Black 16SW CAN Green 1 Data OBDII. Black 1612V Red/White 4 (+) BCM, above driver kick panel. Blue 27Clutch Yellow B MUX Clutch pedal switch. Black 3
Immo. Data Green/Violet 2 Data Transponder Key Amplifier on ignition switch. Violet 3Accessory Violet/Yellow 3 (+) Ignition switch. Black 6Ignition Violet/Black 1 (+) Ignition switch. Black 6Door Input/RAP Off Gray 6 (-) Driver window module in drivers door. Black 7Parking Lights Green/Gray 3 (-) Headlight switch. Black 12HS CAN High Blue 6 Data OBDII. Black 16HS CAN Low White 14 Data OBDII. Black 16SW CAN Green 1 Data OBDII. Black 1612V Red/Yellow 4 (+) BCM, above driver kick panel. Blue 27
Immo. Data Lt. Blue 2 Data Transponder Key Amplifier on ignition switch. Violet 3Accessory Brown 3 (+) Ignition switch. Black 6Ignition Lt. Blue 1 (+) Ignition switch. Black 6Door Input/RAP Off Gray/Black 6 (-) Driver window module in drivers door. Black 8Parking Lights Lt. Blue 3 (-) Headlight switch. Black 12HS CAN High Tan/Black 6 Data OBDII. Black 16HS CAN Low Tan 14 Data OBDII. Black 16SW CAN Dk. Green 1 Data OBDII. Black 1612V Red/White 4 (+) BCM, above driver kick panel. Blue 27
Chevrolet Trax 2013-2016
GMC Terrain 2010-2017
Wire Information Connector Information
Chevrolet Sonic 2012-2016
Door Input/RAP Off Gray (-)
1 2 3 4 5
7
6
121198 10
Important!The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
SW CAN: Green, pin 1
HS CAN High:Blue, pin 6
Ground: Black, pin 4
HS CAN Low:White,pin 14
(+) 12V:pin 16
OBDIIDiagnostic Connector
321
Immo. Data:Green/Violet,pin 2
ImmobilizerControl Module
(black connectorunder ignition switch)
Cut
(-) Driver Door Input [1]
1 8
169
6: White/Black: (-) Hood
Hood Pin
Remote Start Safety Override Switch
Note: Hood pin only required on vehicles not equipped with a factory hood pin.
BCM (under driver-side of dash)
Single Wire CAN: Light Green: 1
(+) Ignition Output: Yellow: 8
(+) 12V Ignition Input: Brown: 7
Immo. Data Interr. (veh. side): Yellow/Red: 11
(+) 12V: Red: 13
(-) Ground: Black: 14
Immo. Data Interr. (conn. side): Orange/Red: 10
[1] (-) RAP Off Output: Green/Black: 2
(-) Parking Lights Output: Black/White: 1
Immo. Data (veh.side): Orange/Black: 11
(+) Accessory Output: Gray/Black: 7
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
[2] (-) Lock Output: Red/Black: 4
[2] (-) Unlock Output: Blue/Red: 12
(-) Lock:Brown/Yellow,pin 19
(-) Unlock:Brown/White,pin 15
[2] ONLY if vehicle is NOT equipped with OnStar
654321
(+) Ignition:Violet/Black, pin 2
(+) Accessory:Violet/Yellow, pin 3
Ignition Switch(black or white 6-pin conn.)
Headlight Switch(black 12-pin conn.)
41
8
9
16
22
17 18 20 21
23 24 26 27
15
19
5
2 3
6 7
10 11 12 13 14
(-) Parking Lights:pin 5
Refer to the Wiring Reference Chart for more information on specific wiring and connections.
Type 2a (Without T-Harness)Page 11
[1] If the RAP Off wire is not connected, the radio will turn OFF but some lights will remain ON in the center console for 10 minutes. Connect this wire (Green/Black, pin 2/12) to the driver door input to avoid the issue. RAP Off/Door Input color and location can be found in the Vehicle Wiring Reference Charts.
[2] ONLY if vehicle is NOT equipped with OnStar.
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
10
DBALL/DBALL2
RF
Prog. Button
LED
4
14
12
2
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
Rev.: 20170412
Platform: DBALL/DBALL2Firmware: GM10 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
1 2 3 4 5
7
6
121198 10
To vehicle 6-pin connector
To Ignition Switch
(6-pin conn.)
Use connectors labeled GM10
[1] (-) RAP Off Output: Green/Black
(-) Parking Light Output: Black/White
N/A: Violet/Green
N/A: Violet/Brown
N/A:Pink
Remote Start Safety Override Switch
Hood Pin
Note: hood pin only required on vehicles not equipped with a factory hood pin
Wh
ite/B
lack
T-HarnessTHGM610(Optional)
Ignition Barrel
Cut away the 4-pin connector and connect the three wires to the OBDII 16-pin connector.
1 8
169
CAN High: Blue, pin 6
Tan
/Bla
ck
CAN Low: White, pin 14
Tan
SW CAN: Green, pin 1
Lt. G
reenTo
Immobilizer Control Module
(vehicle side)
GM10 GM10
T-01
GM06NOT USED
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
To Immobilizer Control Moduleunder ignition switch(black 3-pin connector)
Headlight Switch (black 12-pin conn.)
T-02
Lock and Unlock will only function if vehicle is equipped with OnStar.
(-) Parking Lights:pin 5
T-01
Chevrolet Colorado
Chevrolet Spark
GMC Canyon
T-02
Chevrolet Silverado 1500
Chevrolet Silverado 2500/3500
Chevrolet Suburban
Chevrolet Tahoe
GMC Sierra 1500
GMC Sierra 2500/3500
GMC Yukon
Refer to the Wiring Reference Chart for more information on specific wiring and connections.
(-) Driver Door Input [1]
OR
OBDIIDiagnostic Connector
Type 2b - (With T-Harness - Rev. 1)Page 12
10
DBALL/DBALL2
RF
Prog. Button
LED
4
14
12
2
[1] If the RAP Off wire is not connected, the radio will turn OFF but some lights will remain ON in the center console for 10 minutes. Connect this wire Green/Black wire to the driver door input to avoid the issue. RAP Off/Door Input color and location can be found in the Vehicle Wiring Reference Charts.
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
Rev.: 20170412
Platform: DBALL/DBALL2Firmware: GM10 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Remote Start Safety Override Switch
Hood Pin
Note: hood pin only required on vehicles not equipped with a factory hood pin
Wh
ite/B
lack
Lock and Unlock will only function if vehicle is equipped with OnStar.
Ignition Barrel
To vehicle 6-pin connector
To Ignition 6-pin connector
GM10 GM10
Use connectors labeled GM10.
To Immobilizer Control Module(vehicle side)
[2] RAP Off Output: Green/Black
Diagnostic ConnectorOBDII (connector side view)
1 8
169
CAN High: Blue, pin 6
CAN Low: White, pin 14
Lt.G
ree
n
Ta
n
Ta
n/B
lack
Headlight Switch (black 12-pin conn.)
1 2 3 4 5
7
6
121198 10
(-) Parking Lights: pin 5
GM06
NOT USED
SW CAN: Green, pin 1
T-01
T-02
N/A: Pink
(-) Parking Light Output:Black/White
Cut away the 4-pin connector and connect the three wires to the OBDII 16-pin connector.
T-01
Chevrolet Colorado
Chevrolet Spark
GMC Canyon
T-02
Chevrolet Silverado 1500
Chevrolet Silverado 2500/3500
Chevrolet Suburban
Chevrolet Tahoe
GMC Sierra 1500
GMC Sierra 2500/3500
GMC Yukon
T-HarnessTHGM610/THGM610D(Optional)
Refer to the Wiring Reference Chart for more information on specific wiring and connections.
To Immobilizer Control Moduleunder ignition switch(black 3-pin connector)
(-) Driver Door Input [1]
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
Type 2c - (With T-Harness - THGM610 Rev. 2 & 3 or THGM610D Rev. 1)Page 13
[1] If the RAP Off wire is not connected, the radio will turn OFF but some lights will remain ON in the center console for 10 minutes. Connect this wire Green/Black to the driver door input to avoid the issue. RAP Off/Door Input color and location can be found in the Vehicle Wiring Reference Charts.
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
10
DBALL/DBALL2
RF
Prog. Button
LED
4
14
12
2
Rev.: 20170412
Platform: DBALL/DBALL2Firmware: GM10 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Rev.: 20170412
Platform: DBALL/DBALL2Firmware: GM10 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Page 14
Wire colors should only be used as a reference. You should always test a wire's function and pin location before connecting to it.
Vehicle Wiring Reference Chart - Type 2
Function Color Pin Polarity Location Color Pins
Ignition Violet/Black 1 (+) Ignition Switch Black 6
Accessory Violet/Yellow 3 (+) Ignition Switch Black 6
Parking Lights Lt. Green/Gray 5 (-) Headlight Switch Black 12
Immo. Data Lt. Green/Violet 2 Data Immo. Control Module, under Ignition Switch Violet 3
RAP Off Gray 6 (-) Driver Window Motor Black 7
SW CAN Lt Green 1 Data OBDII Connector Black 16
CAN High Lt. Blue 6 Data OBDII Connector Black 16
CAN Low White 14 Data OBDII Connector Black 16
Ignition Violet/Black 2 (+) Ignition Switch Black 6
Accessory Violet/Yellow 3 (+) Ignition Switch Black 6
Parking Lights Green/Gray 5 (-) Headlight Switch Black 12
Immo. Data Green/Violet 2 Data Immo. Control Module, under Ignition Switch Violet 3
Gray 25 (-) BCM - under driver dash (without power windows) Gray 26
Gray 6 (-) Driver Window Motor (with power windows) Black 7
SW CAN Green 1 Data OBDII Connector Black 16
CAN High Blue 6 Data OBDII Connector Black 16
CAN Low White 14 Data OBDII Connector Black 16
Ignition Violet/Black 2 (+) Ignition Switch Black 6
Accessory Violet/Yellow 3 (+) Ignition Switch Black 6
Parking Lights Green/Gray 5 (-) Headlight Switch Black 12
Immo. Data Green/Violet 2 Data Immo. Control Module, under Ignition Switch Violet 3
Gray 25 (-) BCM - under driver dash (without power windows) Gray 26
Gray 6 (-) Driver Window Motor (with power windows) Black 7
SW CAN Green 1 Data OBDII Connector Black 16
CAN High Blue 6 Data OBDII Connector Black 16
CAN Low White 14 Data OBDII Connector Black 16
Ignition Violet/Black 2 (+) Ignition Switch Black 6
Accessory Violet/Yellow 3 (+) Ignition Switch Black 6
Parking Lights Green/Gray 5 (-) Headlight Switch Black 12
Immo. Data Green/Violet 2 Data Immo. Control Module, under Ignition Switch Violet 3
Gray 25 (-) BCM - under driver dash (without power windows) Gray 26
Gray 6 (-) Driver Window Motor (with power windows) Black 7
SW CAN Green 1 Data OBDII Connector Black 16
CAN High Blue 6 Data OBDII Connector Black 16
CAN Low White 14 Data OBDII Connector Black 16
Ignition Violet/Black 1 (+) Ignition Switch Black 6
Accessory Violet/Yellow 3 (+) Ignition Switch Black 6
Parking Lights Green/Gray 5 (-) Headlight Switch Black 12
Immo. Data Lt. Green/Violet 2 Data Immo. Control Module, under Ignition Switch Black 3
RAP Off Gray 13 (-) BCM - under driver dash Black 27
SW CAN Green 1 Data OBDII Connector Black 16
CAN High Blue 6 Data OBDII Connector Black 16
CAN Low White 14 Data OBDII Connector Black 16
Chevrolet Silverado 2500/3500 2015-2016
RAP Off
Chevrolet Suburban 2015
RAP Off
Chevrolet Spark 2016
Wire Information Connector Information
Chevrolet Colorado 2015-2016
Chevrolet Silverado 1500 2014-2016
RAP Off
Rev.: 20170412
Platform: DBALL/DBALL2Firmware: GM10 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Page 15
Wire colors should only be used as a reference. You should always test a wire's function and pin location before connecting to it.
Vehicle Wiring Reference Chart - Type 2
Function Color Pin Polarity Location Color Pins
Ignition Violet/Black 2 (+) Ignition Switch Black 6
Accessory Violet/Yellow 3 (+) Ignition Switch Black 6
Parking Lights Green/Gray 5 (-) Headlight Switch Black 12
Immo. Data Green/Violet 2 Data Immo. Control Module, under Ignition Switch Violet 3
Gray 25 (-) BCM - under driver dash (without power windows) Gray 26
Gray 6 (-) Driver Window Motor (with power windows) Black 7
SW CAN Green 1 Data OBDII Connector Black 16
CAN High Blue 6 Data OBDII Connector Black 16
CAN Low White 14 Data OBDII Connector Black 16
Ignition Violet/Black 1 (+) Ignition Switch Black 6
Accessory Violet/Yellow 3 (+) Ignition Switch Black 6
Parking Lights Lt.Green/Gray 5 (-) Headlight Switch Black 12
Immo. Data Lt.Green/Violet 2 Data Immo. Control Module, under Ignition Switch Violet 3
RAP Off Gray 6 (-) Driver Window Motor Black 7
SW CAN Lt.Green 1 Data OBDII Connector Black 16
CAN High Lt. Blue 6 Data OBDII Connector Black 16
CAN Low White 14 Data OBDII Connector Black 16
Ignition Violet/Black 2 (+) Ignition Switch Black 6
Accessory Violet/Yellow 3 (+) Ignition Switch Black 6
Parking Lights Green/Gray 5 (-) Headlight Switch Black 12
Immo. Data Green/Violet 2 Data Immo. Control Module, under Ignition Switch Violet 3
Gray 25 (-) BCM - under driver dash (without power windows) Gray 26
Gray 6 (-) Driver Window Motor (with power windows) Black 7
SW CAN Green 1 Data OBDII Connector Black 16
CAN High Blue 6 Data OBDII Connector Black 16
CAN Low White 14 Data OBDII Connector Black 16
Ignition Violet/Black 2 (+) Ignition Switch Black 6
Accessory Violet/Yellow 3 (+) Ignition Switch Black 6
Parking Lights Green/Gray 5 (-) Headlight Switch Black 12
Immo. Data Green/Violet 2 Data Immo. Control Module, under Ignition Switch Violet 3
Gray 25 (-) BCM - under driver dash (without power windows) Gray 26
Gray 6 (-) Driver Window Motor (with power windows) Black 7
SW CAN Green 1 Data OBDII Connector Black 16
CAN High Blue 6 Data OBDII Connector Black 16
CAN Low White 14 Data OBDII Connector Black 16
Ignition Violet/Black 2 (+) Ignition Switch Black 6
Accessory Violet/Yellow 3 (+) Ignition Switch Black 6
Parking Lights Green/Gray 5 (-) Headlight Switch Black 12
Immo. Data Green/Violet 2 Data Immo. Control Module, under Ignition Switch Violet 3
Gray 25 (-) BCM - under driver dash (without power windows) Gray 26
Gray 6 (-) Driver Window Motor (with power windows) Black 7
SW CAN Green 1 Data OBDII Connector Black 16
CAN High Blue 6 Data OBDII Connector Black 16
CAN Low White 14 Data OBDII Connector Black 16
Wire Information Connector Information
RAP Off
GMC Yukon 2015
RAP Off
GMC Canyon 2015-2016
GMC Sierra 1500 2014-2016
RAP Off
GMC Sierra 2500/3500 2016
Chevrolet Tahoe 2015
RAP Off
145 236
Important!The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
SW CAN: Green, pin 1
CAN High: Blue, pin 6
Ground: Black, pin 4
CAN Low:White, pin 14
(+) 12V:Red/Brown,pin 16
321
Immo.Data: Green/Violet, pin 2
ImmobilizerControl Module
(violet connectorunder ignition switch)
Cut
(-) Driver Door Input [1]
1 8
169
6: White/Black: (-) Hood
Hood Pin
Remote Start Safety Override Switch
Note: Hood pin only required on vehicles not equipped with a factory hood pin.
Single Wire CAN: Light Green: 1
(+) Ignition Output: Yellow: 8
(+) 12V Ignition Input: Brown: 7
Immo. Data Interr. (veh.side): Yellow/Red: 11
(+) 12V: Red: 13
(-) Ground: Black: 14
Immo. Data Interr. (conn. side): Orange/Red: 10
[1] (-) RAP Off Output: Green/Black: 2
(-) Parking Lights Output: Black/White: 1
Immo. Data (veh. side): Orange/Black: 11
(+) Accessory Output: Gray/Black: 7
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
(+) Ignition: Violet/Black, pin 4
(+) Accessory:Violet/Yellow, pin 6
Ignition Switch(black or white 6-pin conn.)
Headlight Switch (black 9-pin conn.)54321
986 7
(-) Parking Lights:Green/Gray, pin 2
Refer to the Wiring Reference Chart for more information on specific wiring and connections.
OBDIIDiagnostic Connector
Type 3Page 16
[1] If the RAP Off wire is not connected, the radio will turn OFF but some lights will remain ON in the center console for 10 minutes. Connect this wire (Green/Black, pin 2/12) to the driver door input to avoid the issue. RAP Off/Door Input color and location can be found in the Vehicle Wiring Reference Charts.
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
10
DBALL/DBALL2
RF
Prog. Button
LED
4
14
12
2
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
Rev.: 20170412
Platform: DBALL/DBALL2Firmware: GM10 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Rev.: 20170412
Platform: DBALL/DBALL2Firmware: GM10 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Page 17
Wire colors should only be used as a reference. You should always test a wire's function and pin location before connecting to it.
Vehicle Wiring Reference Chart - Type 3
Function Color Pin Polarity Location Color Pins
Ignition Violet/Black 4 (+) Ignition switch. Gray 6
Accessory Violet/Yellow 6 (+) Ignition switch. Gray 6
Parking Lights Green/Gray 2 (-) Headlight Switch Black 9
Immo. Data Green/Violet 2 Data Immo. Control Module, under Ignition Switch Violet 3
RAP Off Gray 22 (-) BCM, above driver kick panel Pink 27
SW CAN Green 1 Data OBDII Connector Black 16
CAN High Blue 6 Data OBDII Connector Black 16
CAN Low White 14 Data OBDII Connector Black 16
Wire Information Connector Information
Chevrolet Spark 2013-2015
SmartStart/XL202 Installation Notes
The optional XL202 and antenna are not included and MUST be purchased separately.
Refer to the Passive Keyless Entry (PKE) Installation Guide (N2102T) for detailed wiring information.
4
4
XL202
An
ten
na
XOVER
SmartStart is optional and not included. It MUST be purchased separately.
SmartStart is optional and not included. It MUST be purchased separately.
Configuration Wires (Gray & White)Connect Gray wire to (-) Ground
5 pins
D2D (4 pins, white)
4 pins
2 pins, not usedCABLE
CABLE
The modules must be connected in a specific order. Refer to the Module Programming section for more information.
1. Use the D2D Crossover (XOVER) cable that is provided with XL202, and NOT the one in the DBALL package.2. The modules must be connected in a specific order. Refer to the Module Programming section for more information.
The modules must be connected in a specific order. Refer to the Module Programming section for more information.
SmartStart Revision B
RF Kit
RF Kit & PKE Combination
Refer to the Passive Keyless Entry (PKE) Installation Guide (N2102T) for detailed wiring information.
RF Kit, PKE & SmartStart BT Combination
SmartStart Revision A
DBALL/DBALL2
DBALL/DBALL2
DBALL/DBALL2
LED
Prog.Button
D2D (4 pins, white)
4 pins
2 pins, not used
OR
SmartStart
Configuration Wires (White & Brown or Blue)Cut Brown or Blue Loop
LED
THIS SIDE UP
LED
Page 18
The DBALL Remote Start Ready (RSR) solution offers three (3) configuration options to control your system: 3x OEM Lock Remote Start Activation, RF Kits or SmartStart (all sold separately). This section provides specific installation information for SmartStart and XL202.
Rev.: 20170412
Platform: DBALL/DBALL2Firmware: GM10 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Page 19
Module Programming
Refer to the LED Diagnostics section on page 24 for more information and for troubleshooting purposes.
Remove the key from the ignition barrel.The LED will keep flashing green.
Key OUT OF
F
START
IGN
3
2
4
Turn the key to the ACC position.The LED will start to flash orange. &
Key IN OF
F
IGN
ACC
START
Key IN OF
F
IGN
ACC
START
Flashes
Turn the key to the IGN position.The LED will start to flash green continuously. &
Flashescontinuously
Go to the next page to complete the module programming.
Important
1 10-pinD2D
st1
12-pin14-pin
nd2
rd3
&Solid
Connect the 10-pin, 12-pin and 14-pin harnesses to DBALL, then wait until the LED turns ON solid red.
10-pinD2D
XL202
10-pinD2DSmartStart
OR
The DBALL module must be disconnected from any power source before SmartStart can be connected to it. Failing to do so could damage DBALL.
a. To ensure that the D2D communication between SmartStart and DBALL works properly, the Gray wire must be connected to a ground source (Rev B SmartStart), and the Brown or Blue loop must be cut (Rev A SmartStart).
b. Do NOT connect the 2-pin harness (on SmartStart). Power and ground will be provided by the DBALL D2D connector.
Connect SmartStart to DBALL using the D2D port.
SmartStart Installation
Connect XL202 to DBALL using the D2D port.
XL202 Installation
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step.
Note: Before connecting either the XL202 or SmartStart module to DBALL, it is important to ensure that the proper feature and function programming is selected using XpressVIP (version 4.5 or higher). Visit www.directechs.com to download the latest version of the application.
Warning! To take advantage of advanced features, you must use XpressVIP 4.5 (and higher) or the Directechs Mobile app.
When the flashing operation is successful, you can proceed with the programming instructions below.
Flashing a module using your computer:
1. Connect the interface module to your computer using the XKLoader2.
2. Go to www.directechs.com using Internet Explorer, and select the Config for RSR button.
3. Follow the instructions to select your vehicle, installation type, and configure your options.
4. Once you have configured the firmware options, click on the FLASH button.
Flashing a module using your smartphone or tablet
1. Connect the interface module to your XKLoader3.
2. Launch the Directechs Mobile app on your smartphone or tablet.
3. Select FLASH YOUR MODULE and follow the on screen instructions.
Rev.: 20170412
Platform: DBALL/DBALL2Firmware: GM10 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Page 20
You have successfully completed the module programming sequence.
5
Within 1 sec.
Insert the key and turn it to the IGN position. The LED turns ON solid green for 3 seconds then shuts off.
Note: If the LED flashes slowly orange, Key2GO programming will be required for your vehicle.
Remove the module from the vehicle and reconnect it to your computer. The Directechsweb site will automatically recognize that you are moving onto the second phase of theprogramming sequence. Select the method and click on Submit Key2Go Request. Once theconfiguration is completed, reconnect the module.
Key IN OF
F
START
IGN
& &
Solid 3x secs Off
6 Remove the key from the ignition barrel.Key OUT O
FF
START
IGN
Rev.: 20170412
Platform: DBALL/DBALL2Firmware: GM10 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Rev.: 20170412
Platform: DBALL/DBALL2Firmware: GM10 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
1If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.
10-pinD2D
st1
12-pin14-pin
nd2
th4
rd3
Warning Against Executing a Hard Reset! A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such as RFTD and D2D options) may have to be reconfigured. See the Feature & Option List section of this guide.
2
Solid
&Release
3 Release the programming button. The LED turns ON solid red.
Module Reset
Hard Reset
2 & &
1
Wait 3 seconds until the LED turns ON solid orange then release the programming button. The LED turns ON solid red.
If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.
10-pinD2D
st1
12-pin14-pin
nd2
th4
rd3
A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed to the module using the web config tool will not be affected.
Solid Release Solid
Solid Flashes
&Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds until the LED starts to flash orange and red.
Page 21
Feature & Option ListPage 22
It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page on www.directechs.com. The web offers more options such as RSR; however, manual configuration of the features is possible using the information on this page.
Feat. Operation Flashes/Option Description
1. No RF
Output*Module is connected to a remote starter using a standard installation.
2. RFTD Output Module is connected to an XL202 using an RSR or RXT installation (when available).
3. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).
1. Driver
priority*
Unlocks only the driver door when the button is first pressed, and unlocks all doors when it is
pressed a second time within 5 seconds.
2. All Unlocks all doors when the button is first pressed.
1. Disabled* No action.
2. Enabled for
WindowsModule will perform windows roll up upon lock command.
3. Enabled for
Windows and
Sunroof
Module will perform windows roll up and close sunroof upon lock command.
1. Disabled* No operation.
2. Enabled When the feature is enabled, it will activate the Heated Seats and heated steering wheel.
1. 32°F (0°C)*When Heated Seats or Defroster feature is enabled, it will activate the feature upon remote start
when temperature is below 32 °F (0 °C).
2. 23°F (-5°C)When Heated Seats or Defroster feature is enabled, it will activate the feature upon remote start
when temperature is below 23 °F (-5 °C).
3. 41°F (+5°C)When Heated Seats or Defroster feature is enabled, it will activate the feature upon remote start
when temperature is below 41 °F (5 °C).
4. Always ON When Heated Seats or Defroster feature is enabled, it will activate the feature at any temperature.
1. Disabled
The OEM alarm will not be controlled by the interface upon remote start. No disarm or arm
command will be executed at the beginning or end of the sequence; it must be controlled by the
Remote Starter.
2. SafelockSmart OEM Alarm Control will behave like a standard Safelock feature on a remote starter. It will
unlock at the beginning of the sequence, and relock after start and shutdown.
3. Enabled*
Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm and rearm the
vehicle in the remote start sequence, only when required. Smart OEM Alarm Control will monitor
the alarm and door lock status to detect if the disarm or rearm is required. If the vehicle is unlocked
or is not equipped with factory alarm, the disarm/rearm will not be executed.
Smart OEM Alarm
Control6
Heated
Seats/Defroster
Temperature Control
5
* Default Option
RFTD Output Type1
Unlock Driver Priority
4
Comfort Closure with
Lock3
2
Heated Seats
Rev.: 20170412
Platform: DBALL/DBALL2Firmware: GM10 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Page 23
To enter feature programming routine- Turn the ignition ON, then OFF. - Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the
Programming button.- The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate
the current option of feature 1 (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1). The flashing sequence will repeat until a new command is entered.
Changing feature options- Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. When installing the
DBALL in RSR using 3x OEM Lock Remote Start Activation only, there is no aftermarket transmitter on which to press lock/unlock to change the options of the selected feature. Tapping the green or blue lock/unlock wires on the black 10-pin harness to ground will change the option for the selected feature.
- The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green slowly the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered.
Accessing another feature- Press and release the programming button a number of times to advance from the current feature to the next desired feature. - The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to
indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered.
When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option.
Once a feature is programmed- Other features can be programmed.- The feature programming can be exited.
Exiting feature programming- No activity for 30 seconds; after 30 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming
sequence.OR
- Press and HOLD the programming button for 3 seconds. After 3 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming sequence.
Feature ProgrammingProgramming
Button
Rev.: 20170412
Platform: DBALL/DBALL2Firmware: GM10 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Page 24
LED Diagnostics & Troubleshooting
LED Description Troubleshooting
Module has no power.
Make sure the D2D harness is connected or that the 12
Volt is present between the red and black wires. If the
12 Volt is present, the module may be defective.
Waiting to begin the programming sequence.Ensure the correct programming procedure is being
followed.
Initialization failed.Reset the module and complete the programming again.
If the issue persists, please contact Technical Support.
Transponder functions were skipped.
(If compatible) when RXT mode is not desired or
convenience features are needed, please reset and
reprogram the module.
All required CAN networks has been detected. Normal operation.
1 of 2 CAN networks has been detected. Normal operation
Key2GO initiated.Please follow the steps indicated in “Module
programming” to complete the Key2GO programming.
Module was successfully programmed with all functions. Normal operation
Module was successfully programmed without
transponder functions.Normal operation.
CAN2 not detected.
Check the CAN2 Orange/Green and Orange/Brown wire
connections. Wake up the data bus by turning the
ignition on and try again. If your installation does not
require this connection, skip this step by pressing the
programming button 5 times.
J1850 not detected.Check the J1850 wire connection. Wake up the data bus
by turning the ignition on and try again.
CAN1 not detected.
Check the CAN1 Tan and Tan/Black wire connections.
Wake up the data bus by turning the ignition on and try
again. If your installation does not require this
connection, skip this step by pressing the programming
button 5 times.
Bypass data not detected.
Check the bypass line connection. If more than one wire
is used, make sure they are not inverted. Ensure the
vehicle still operates correctly using the factory key.
Bypass processing error.
The bypass calculation failed. Reset the module and try
again. If the condition persists, please contact Technical
Support.
ISO 1 not detected.
The Yellow/Black wire did not detect the expected
signal. Refer to "Installation (wiring diagrams & vehicle
wiring reference charts)" to check the connections.
ISO 2 not detected.
The Orange/Black wire did not detect the expected
signal. Refer to "Installation (wiring diagrams & vehicle
wiring reference charts)" to check the connections.
MUX not detected.
The Violet/Green or Violet/Brown wire did not detect the
expected voltage value. Refer to "Installation (wiring
diagrams & vehicle wiring reference charts)" to check
the connections.
Module Programming
Module Programming - Error Codes
Solid red
Flashes redx 1
Flashes redx 1
Flashes redx 2
Flashes redx 3
Flashes redx 4
Flashes redx 5
Flashes redx 6
Flashes redx 7
Solid greenx 3 secs
Flashesgreen
Solid orange
Flashes red& green
Off
Flashesorange
Flashesorangeslowly
Solid orangex 3 secs
Rev.: 20170412
Platform: DBALL/DBALL2Firmware: GM10 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Page 25
LED Description Troubleshooting
OBDII feature is not supported.The diagnostic data bus was not detected, therefore the
SmartStart features will be limited.
Ground When Running (Status) command received. The module has initialized the remote start sequence.
Ignition ON command received.The module has received the Ignition ON command and
is processing the remote start sequence.
Start ON command received.The module has received the Start ON command and is
processing the remote start sequence.
PTS shutdown error.The PTS output from the module was not activated due
to safety protection.
CAN bus incorrectly detected.
Verify the CAN1 and CAN2 connections. Refer to
“Installation (wiring diagrams & vehicle wiring reference
charts)” to check the connections.
LOCK command received.
UNLOCK command received.
TRUNK command received.
AUX1 command received.
AUX2 command received.
AUX3 command received.
Takeover successful. Normal operation.
Runsafe was not disabled.No UNLOCK command was received prior to opening the
door, or the 45 second timer expired in takeover mode.
Brake was not detected.The brakes were not detected, which prevents the
system from shutting down the vehicle.
Smart key was not detected.The smart key was not detected, which prevents the
system from shutting down the vehicle.
Speed was detected.The vehicle was detected as moving, which prevents the
system from shutting it down.
3x OEM Lock Remote Start Activation was attempted
when RFTD feature is disabled.
Activated from Web automatically when using RSR flash
tool or can be done manually. Refer to feature
programing section for more information.
Feature error.An RSR feature file mismatch was detected. Please
contact Technical Support.
RSR codes
External module synchronization
Commands
Activation Ground When Running (Status)
If the bypass module fails to flash, it did not receive the
signal. Commands can come from RF or D2D.
Shutdown codes
(Flashes red,red thenorange) x 10
Flashes red& orange
Flashes redx 21
Flashes redx 2
Flashes redx 4
Flashes redx 7
Flashes redx 9
Flashes redx 10
Flashes redx 1
Flashes redx 3
Flashesgreen
Flashesgreenquickly
Flashesgreen x 1
Flashesorange x 1
Flashesorange x 2
Flashesorange x 3
Flashesorange x 5
Flashesorange x 4
Flashesorange x 6
Rev.: 20170412
Platform: DBALL/DBALL2Firmware: GM10 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Limited One Year Consumer WarrantyPage 26
For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and Part description.
This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED’S OPTION THE PART AS DESCRIBED ABOVE.
This warranty only covers Parts sold within the United States of America and Canada. Parts sold outside of the United States of America or Canada are sold “AS-IS” and shall have NO WARRANTY, express or implied. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.For further details relating to warranty information of Directed products, please visit the support section of DIRECTED’s website at: www.directed.com
920-10012-01 2013-07
This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only.
Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876 B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1; 7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent: 2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; European Patent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.
Rev.: 20170412
Platform: DBALL/DBALL2Firmware: GM10 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Quick Reference GuideDBALL/DBALL2-GM10 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Button(s) Actions
Press & hold for 1 second to lock.
Press & hold for 1 second to unlock.
Press & hold for 1 second to remote
start.
Press & hold for 5 seconds to activate
the trunk release (optional).
Press once, then to activate the
rear hatch/tail glass release (optional).*
Press 3 times, then to activate
the panic mode.
Press once, then to reset the
remote starter runtime.
List of Available Commands
x1 +
x3 +
x1 +
* This output is configurable. see your authorized installation center for more information.
Note that the information below is for Viper, Clifford and Python models. Icons and commands may differ depending on the remote brand and model purchased. Refer to your authorized installation center for more information.
Remote Start Ready (RSR)
Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance.
Parking Light Error CodesThe parking lights on your vehicle will flash a specific number of times 3 seconds following an unscheduled shutdown or failure to start. Each flashing pattern is described below.
Flashes Diagnostic
1 Runtime expired.
2 Over-rev shutdown.
3 Low/No RPM.
4 Transmitter shutdown.
5 Brake shutdown.
6 Hood shutdown/Remote start safety override switch is ON*.
7 Remote start safety override switch is ON*.
3x OEM Lock Remote Start Activation
This solution includes the option to remote start your vehicle by pressing the Lock button 3 times consecutively. If your vehicle allows the OEM remote to remain active while the engine is running, you may shut down your remote starter by pressing the Lock button 3 times once more.
Note: The range offered by OEM remotes is limited and typically requires you to be within eyesight of the vehicle to control it.
* If the vehicle hood status is supported through data, it will also report a 7 flash safety override code.
Quick Reference GuideDBALL/DBALL2-GM10 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
NotesSmartStart Compatible
This system is compatible with Directed SmartStart 3.0. For a complete list of supported features, please visit www.mysmartstart.com.
What is SmartStart?
Now you can remote start, lock and unlock your car just by pushing a button on your smartphone; using the SmartStart App from Directed, the leader in vehicle security and remote start. The simple graphical interface gives you control over the following features of your installed remote start or security with remote start system:
Lock/Arm Unlock/Disarm Remote Car Starter Trunk Release Panic Aux Channels
You can also control multiple vehicles – great for families – and assign more than one user to control a vehicle. It's easy with SmartStart!
But, this is only the beginning! SmartStart is loaded with additional features including GPS tracking, SmartSchedule, vehicle status, roadside assistance, home control, parked car finder and more.
3.0 enables a "Cloud-Connected Car" like never before, providing an entirely new level of 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet.
For more information, visit www.mysmartstart.com.