Post on 07-Jul-2020
EC centrifugal blowersdual inlet
version 04/2008
The engineer’s choice
D3G_englisch:Axial_D 30.04.2008 10:57 Seite 1
2
New EC centrifugal blowers dual inlet
Energy savings, convenient control and low noise
Cylindrical rotor fans in EC technology
Saving energy is becoming an ever increasingly important topic these days. Especially when it comes
to air-conditioning and ventilation technology, great potential savings can be achieved by using energy-
efficient fans. For this reason, motor and fan specialist ebm-papst Mulfingen has recognised the issue,
and has developed a complete series of dual-inlet, direct-driven cylindrical rotor fans with efficient EC
technology. Without changing the design of the unit, this allows a conversion from a conventional fan
with asynchronous motor to modern energy-saving technology.
The advantages of EC fans speak for themselves. Because the electronically commutated external rotor
motor is integrated within the forward curved impeller, the installation dimensions are reduced and
there is no longer any need for the commonly required belt drive between the motor attached on the
outside and the impeller. This reduces the fan dimensions always desirable for ventilation and
air-conditioning technology as well as the associated installation effort.
Furthermore, the electronically commutated motors are extremely quiet and operate at efficiencies of
up to 90 %. Thus they attain significantly higher values than most voltage-controlled asynchronous
motors, which have typical efficiencies of between 30 % and 60 %. At the same operating point, there-
fore, the power consumption of the EC fans is considerably less.
With integrated motor electronics, the EC fans can be easily speed controlled via a 0-10 V signal or by
the use of a potentiometer. As an option up to three air flow values can be programmed in "Constant
Flow" mode. This means that if the system resistance changes, for example due to polluted filters, the
fan keeps the programmed air flow by changing the speed automatically.
Depending on the motor type used, the double inlet fans with state-of-the-art EC technology cover
almost every conceivable application area. You can choose between eleven sizes with drive outputs
between 85 W and 3 kW. Thus a customised solution is available for virtually any application, including
compact air handling units, air curtains for doors and gates, fan coils, air heaters for factory buildings
or as a cooling fan for forced cooling of power converters, generators or telecommunications systems.
D3G_englisch:Axial_D 30.04.2008 10:57 Seite 2
3
Size 133 4
New EC centrifugal blowers dual inlet 2
Size 146 6
Size 160 8
Size 180 10
Size 200 12
Table of content
Size 225 14
Size 283 (10�� 22
Size 250 16
Size 318 (12�� 26
Size 404 (15�� 34
Size 454 (18�� 38
Electrical connections 40
Distributors, agencies and subsidiaries 46
D3G_englisch:Axial_D 30.04.2008 10:57 Seite 3
4
EC centrifugal blowersdual inlet, Ø 133
– Material: Housing: Galvanised sheet steelImpeller: Galvanised sheet steelRotor: GalvanisedElectronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor– Type of protection: IP 44– Insulation class: "B"– Mounting position: Any– Condensate discharges: Rotor-side– Mode of operation: Continuous operation (S1)– Bearings: Maintenance-free ball bearings
Nominal data
Type Motor
D3G 133 M3G 055-CF
subject to alterations
100 200 300 400 500 600 700 800
0 [CFM]
[Pa]
20
40
60
80
100
120
140
160
180
200
220
240
260
280
0,2
0,4
0,6
[in H
2O]
0,8
1,0
[m3/h]
200100 300 400 50059
10
11
12
1615
14
13
6
7
8
3
4
2
1
Curves
(1) Nominal data in operating point with maximum load
VAC Hz rpm W A Pa °C
1~ 230 50/60 1280 86 0,65 0 -25..+40
Curv
e
Nom
inal
vol
tage
Freq
uenc
y
Spee
d/rp
m
Perm
. am
b. te
mp.
Min
. bac
k pr
essu
re
n[rpm]
P1[W]
LpA[dB(A)]
ηtL[%]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Max
. pow
erin
put(1
)
Max
. cur
rent
draw
(1)
p. 40
H1)
Elec
tr. c
onne
ctio
n
I[A]
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
1280
1550
1825
2055
1270
1460
1720
1930
1110
1270
1440
1570
855
960
1070
1110
86
82
62
47
83
69
51
39
53
44
30
22
25
21
15
10
60
58
54
53
59
56
53
53
55
51
48
48
49
43
39
38
—
46
53
44
—
44
53
41
—
44
51
40
—
41
40
31
0,65
0,63
0,48
0,36
0,63
0,54
0,39
0,30
0,41
0,34
0,23
0,17
0,19
0,16
0,12
0,09
A
D3G_englisch:Axial_D 30.04.2008 10:57 Seite 4
5
– Technical features: • Tach output• Control input 0-10 VDC / PWM • Locked-rotor protection• Output 10 VDC max. 1.1 mA
– EMC: Interference emission acc. to EN 61000-6-3Interference immunity acc. to EN 61000-6-1Harmonics acc. to DIN EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 60950-1– Cable exit: Variable– Protection class: I– Product conforming to standards: EN 60335-1, CE– Approvals: GOST; UL, VDE, CSA, CCC are applied for
Centrifugal blowerwith flange
D3G 133-BF03 -02
kg
3,0
max. 8 m
mDepth of screw
Einschraubtiefe
20497
213
93.5
450+20
270254
100
Ø112
Ø5.512
614
2
232
Mas
s of
cent
rifug
al b
low
er
Electr. connectionp. 40
Brass lead tips
D3G_englisch:Axial_D 30.04.2008 10:57 Seite 5
6
EC centrifugal blowersdual inlet, Ø 146
– Material: Housing: Galvanised sheet steelImpeller: Galvanised sheet steelRotor: GalvanisedElectronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor– Type of protection: IP 44– Insulation class: "B"– Mounting position: Shaft horizontal; rotor on top or rotor on bottom on request– Condensate discharges: None– Mode of operation: Continuous operation (S1)– Bearings: Maintenance-free ball bearings
Motor
D3G 146 M3G 074-CF
200 600400 800 1000
0 [CFM]
[Pa]
100
200
300
400
0,5
1,0
1,5
[in H
2O]
[m3/h]
200 300 400 500 60010059
10
11
12
6
7
83
4
2
1
Curves
1~ 230 50/60 1740 171 1,30 0 -25..+60
n[rpm]
P1[W]
LpA[dB(A)]
ηtL[%]
1
2
3
4
5
6
7
8
9
10
11
12
p. 41
J1)
I[A]
A
A
A
A
A
A
A
A
A
A
A
A
A
A 1740
1960
2150
2410
1460
1650
1820
2020
1090
1220
1330
1480
171
169
165
166
103
102
104
102
47
46
46
46
67
65
65
66
62
60
60
61
55
56
52
53
—
49
56
55
—
46
53
52
—
41
47
44
1,30
1,20
1,20
1,20
0,70
0,80
0,80
0,70
0,40
0,40
0,40
0,40
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load
VAC Hz rpm W A Pa °C
Curv
e
Nom
inal
vol
tage
Freq
uenc
y
Spee
d/rp
m
Perm
. am
b. te
mp.
Min
. bac
k pr
essu
re
Max
. pow
erin
put(1
)
Max
. cur
rent
draw
(1)
Elec
tr. c
onne
ctio
n
D3G_englisch:Axial_D 30.04.2008 10:57 Seite 6
7
– Technical features: • Output 10 VDC max. 1.1 mA• PFC (passive) • Tach output• Control input 0-10 VDC / PWM • Over-temperature protected electronics / motor
– EMC: Interference emission acc. to EN 61000-6-3Interference immunity acc. to EN 61000-6-1Harmonics acc. to DIN EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 60950-1– Cable exit: Variable– Protection class: I– Product conforming to standards: EN 60335-1, EN 61800-5-1, EN 60950-1, CE– Approvals: UL, CSA; CCC, GOST are applied for
D3G 146-AH50 -11
kg
4,2
20696
9821
9
270254
Ø117
100
Ø5.512
614
2
350+20
232
Electr. connectionp. 41
Core-end sleeves
Centrifugal blowerwith flange
Mas
s of
cent
rifug
al b
low
er
D3G_englisch:Axial_D 30.04.2008 10:57 Seite 7
8
EC centrifugal blowersdual inlet, Ø 160
– Material: Housing: Galvanised sheet steelImpeller: Galvanised sheet steelRotor: GalvanisedElectronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor– Type of protection: IP 44– Insulation class: "B"– Mounting position: Shaft horizontal; rotor on top or rotor on bottom on request– Condensate discharges: None– Mode of operation: Continuous operation (S1)– Bearings: Maintenance-free ball bearings
Motor
D3G 160 M3G 074-CF
200 600400 800 1000
0 [CFM]
[Pa]
40
80
120
160
200
240
0,5
1,0
[in H
2O]
0,25
0,75
[m3/h]
200 300 400 500 60010059
10
11
12
6
7
8
3
4
2
1
Curves
1~ 230 50/60 1390 154 1,20 0 -25..+60
n[rpm]
P1[W]
LpA[dB(A)]
ηtL[%]
1
2
3
4
5
6
7
8
9
10
11
12
p. 41
J1)
I[A]
A
A
A
A
A
A
A
A
A
A
A
A
A
A 1390
1440
1540
1590
1180
1220
1270
1310
860
890
910
930
154
129
93
63
96
79
54
37
40
34
24
18
64
61
57
56
59
56
52
51
51
47
43
42
—
53
60
47
—
52
57
44
—
45
45
31
1,20
1,00
0,70
0,50
0,70
0,60
0,40
0,30
0,30
0,30
0,20
0,20
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load
VAC Hz rpm W A Pa °C
Curv
e
Nom
inal
vol
tage
Freq
uenc
y
Spee
d/rp
m
Perm
. am
b. te
mp.
Min
. bac
k pr
essu
re
Max
. pow
erin
put(1
)
Max
. cur
rent
draw
(1)
Elec
tr. c
onne
ctio
n
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 8
9
– Technical features: • Output 10 VDC max. 1.1 mA• PFC (passive) • Tach output• Control input 0-10 VDC / PWM • Over-temperature protected electronics / motor
– EMC: Interference emission acc. to EN 61000-6-3Interference immunity acc. to EN 61000-6-1Harmonics acc. to DIN EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 60950-1– Cable exit: Variable– Protection class: I– Product conforming to standards: EN 60335-1, EN 61800-5-1, EN 60950-1, CE– Approvals: UL, CSA; CCC, GOST are applied for
D3G 160-BF60 -11
kg
5,5
226102
241
100,
5
270254
232
103
Ø130
Ø5.5
129
145
400+20
Electr. connectionp. 41
Core-end sleeves
Centrifugal blowerwith flange
Mas
s of
cent
rifug
al b
low
er
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 9
10
EC centrifugal blowersdual inlet, Ø 180
– Material: Housing: Galvanised sheet steelImpeller: Galvanised sheet steelRotor: GalvanisedElectronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor– Type of protection: IP 44– Insulation class: "B"– Mounting position: Shaft horizontal; rotor on top or rotor on bottom on request– Condensate discharges: None– Mode of operation: Continuous operation (S1)– Bearings: Maintenance-free ball bearings
Motor
D3G 180 M3G 074-CF
400 800 1200 1600
0 [CFM]
[Pa]
50
100
150
200
250
0,25
0,50
0,75
[in H
2O]
1,00
[m3/h]
500250 75059
10
11
12
1615
14
13
6
7
8
3
4
2
1
Curves
1~ 230 50/60 1090 165 1,22 0 -25..+60
n[rpm]
P1[W]
LpA[dB(A)]
ηtL[%]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
p. 41
J1)
I[A]
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A 1090
1200
1310
1400
925
1015
1090
1145
690
760
805
840
455
500
525
545
165
155
113
74
101
95
67
45
43
42
31
21
15
15
12
9
64
62
59
56
60
58
54
51
52
50
46
43
40
38
34
32
—
54
62
53
—
51
61
48
—
47
51
39
—
36
35
23
1,22
1,15
0,85
0,55
0,75
0,70
0,50
0,35
0,35
0,30
0,25
0,20
0,15
0,15
0,10
0,10
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load
VAC Hz rpm W A Pa °C
Curv
e
Nom
inal
vol
tage
Freq
uenc
y
Spee
d/rp
m
Perm
. am
b. te
mp.
Min
. bac
k pr
essu
re
Max
. pow
erin
put(1
)
Max
. cur
rent
draw
(1)
Elec
tr. c
onne
ctio
n
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 10
11
– Technical features: • Output 10 VDC max. 1.1 mA• PFC (passive) • Tach output• Control input 0-10 VDC / PWM • Over-temperature protected electronics / motor
– EMC: Interference emission acc. to EN 61000-6-3Interference immunity acc. to EN 61000-6-1Harmonics acc. to DIN EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 60950-1– Cable exit: Variable– Protection class: I– Product conforming to standards: EN 60335-1, EN 61800-5-1, EN 60950-1, CE– Approvals: UL, CSA; CCC, GOST are applied for
D3G 180-AB62 -01
kg
7,0
296133
333
309289180
132
Ø149
Ø7
90 168
188
136
600+
20
255
Electr. connectionp. 41
Core-end sleeves
Centrifugal blowerwith flange
Mas
s of
cent
rifug
al b
low
er
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 11
12
EC centrifugal blowersdual inlet, Ø 200
– Material: Housing: Galvanised sheet steelImpeller: Galvanised sheet steelRotor: Coated in blackElectronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor– Type of protection: IP 54– Insulation class: "B"– Mounting position: Shaft horizontal– Condensate discharges: None– Mode of operation: Continuous operation (S1)– Bearings: Maintenance-free ball bearings
Motor
D3G 200 M3G 084-FA
400 800 1200 1600 2000
0 [CFM]
[Pa]
40
80
120
160
200
240
280
320
360
400
440
0,2
0,4
1,0
[in H
2O]
0,6
0,8
1,2
1,4
1,6
1,8
[m3/h]
400200 600 800 1000 1200
5
9
101112
16 15 1413
6
78
3
4
2
1
Curves
1~ 230 50/60 1640 465 3,00 225 -25..+50
n[rpm]
P1[W]
LpA[dB(A)]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
p. 42
K1)
I[A]
1640
1665
1750
1825
1425
1425
1425
1425
950
950
950
950
475
475
475
475
465
402
308
225
337
251
166
107
100
74
49
32
12
9
6
4
70
68
66
66
68
65
61
61
56
53
50
50
37
34
32
32
3,00
2,60
1,98
1,48
2,18
1,62
1,07
0,70
0,65
0,48
0,32
0,21
0,08
0,06
0,04
0,03
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load
VAC Hz rpm W A Pa °C
Curv
e
Nom
inal
vol
tage
Freq
uenc
y
Spee
d/rp
m
Perm
. am
b. te
mp.
Min
. bac
k pr
essu
re
Max
. pow
erin
put(1
)
Max
. cur
rent
draw
(1)
Elec
tr. c
onne
ctio
n
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 12
13
– Technical features: • Output 10 VDC max. 1.1 mA• PFC (passive) • Alarm relay• Control input 0-10 VDC / PWM • Over-temperature protected electronics / motor
– EMC: Interference emission acc. to EN 61000-6-3Interference immunity acc. to EN 61000-6-2Harmonics acc. to DIN EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 61800-5-1– Cable exit: Variable– Protection class: I– Product conforming to standards: EN 61800-5-1, CE– Approvals: UL, CSA; CCC, GOST is applied for
D3G 200-BB22 -71
kg
9,4
146327
371
151
800 +20
141
341321180
287
Ø7
90 180
200
Ø167
Electr. connectionp. 42
Core-end sleeves
Centrifugal blowerwith flange
Mas
s of
cent
rifug
al b
low
er
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 13
14
EC centrifugal blowersdual inlet, Ø 225
– Material: Housing: Galvanised sheet steelImpeller: Galvanised sheet steelRotor: Coated in blackElectronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor– Type of protection: IP 54– Insulation class: "B"– Mounting position: Shaft horizontal– Condensate discharges: None– Mode of operation: Continuous operation (S1)– Bearings: Maintenance-free ball bearings
Motor
D3G 225 M3G 084-FA
400 800 1200 1600 2000 2400
0 [CFM]
[Pa]
40
80
120
160
200
240
280
320
0,2
0,4
1,0
[in H
2O]
0,6
0,8
1,2
[m3/h]
400200 600 800 1000 1200 1400
5
9
101112
16 15 1413
6
78
3
4
2
1
Curves
1~ 230 50/60 1150 375 2,30 150 -25..+50
n[rpm]
P1[W]
LpA[dB(A)]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
p. 42
K1)
I[A]
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
1150
1210
1275
1345
1050
1050
1050
1050
700
700
700
700
350
350
350
350
375
320
260
190
278
209
145
90
82
62
43
27
10
8
5
3
67
66
64
62
65
62
59
56
53
51
48
45
34
32
31
28
2,30
2,07
1,69
1,26
1,69
1,35
0,94
0,60
0,50
0,40
0,28
0,18
0,06
0,05
0,03
0,02
A
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load
VAC Hz rpm W A Pa °C
Curv
e
Nom
inal
vol
tage
Freq
uenc
y
Spee
d/rp
m
Perm
. am
b. te
mp.
Min
. bac
k pr
essu
re
Max
. pow
erin
put(1
)
Max
. cur
rent
draw
(1)
Elec
tr. c
onne
ctio
n
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 14
15
– Technical features: • Output 10 VDC max. 1.1 mA• PFC (passive) • Alarm relay• Control input 0-10 VDC / PWM • Over-temperature protected electronics / motor
– EMC: Interference emission acc. to EN 61000-6-3Interference immunity acc. to EN 61000-6-2Harmonics acc. to DIN EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 61800-5-1– Cable exit: Variable– Protection class: I– Product conforming to standards: EN 61800-5-1, CE– Approvals: UL, CSA; CCC, GOST is applied for
D3G 225-CC14 -71
kg
10,8
327158
370
151
800+20
250
141
Ø194
387367180
333
180
284
304
Ø7
Electr. connectionp. 42
Core-end sleeves
Centrifugal blowerwith flange
Mas
s of
cent
rifug
al b
low
er
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 15
16
EC centrifugal blowersdual inlet, Ø 250
– Material: Housing: Galvanised sheet steelImpeller: Galvanised sheet steelRotor: Coated in blackElectronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor– Type of protection: IP 54– Insulation class: "B"– Mounting position: Shaft horizontal– Condensate discharges: None– Mode of operation: Continuous operation (S1)– Bearings: Maintenance-free ball bearings
Motor
D3G 250 M3G 084-GF
Curves
1~ 230 50/60 1085 450 2,80 100 -25..+40
n[rpm]
P1[W]
LpA[dB(A)]
p. 42
K1)
I[A]
A
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load
VAC Hz rpm W A Pa °C
Curv
e
Nom
inal
vol
tage
Freq
uenc
y
Spee
d/rp
m
Perm
. am
b. te
mp.
Min
. bac
k pr
essu
re
Max
. pow
erin
put(1
)
Max
. cur
rent
draw
(1)
Elec
tr. c
onne
ctio
n
40
80
120
160
200
240
280
320
360
0,2
0,4
1,0
0,6
0,8
1,2
1,4
500 1000 1500 2000 2500
0 [CFM]
[Pa]
[in H
2O]
[m3/h]
500 1000 1500
10
13
1112
1615
14
6
7
8
3
4
2
1
5
9
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1085
1125
1175
1285
1000
1000
1000
1000
800
800
800
800
600
600
600
600
450
401
346
232
346
282
213
110
177
145
109
56
75
61
46
24
71
69
67
65
69
66
63
58
63
60
56
52
55
51
48
44
2,80
2,55
2,20
1,50
2,21
1,80
1,36
0,71
1,13
0,92
0,70
0,37
0,48
0,39
0,29
0,15
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 16
17
– Technical features: • Output 10 VDC max. 1.1 mA• PFC (passive) • Alarm relay• Control input 0-10 VDC / PWM • Over-temperature protected electronics / motor
– EMC: Interference emission acc. to EN 61000-6-3Interference immunity acc. to EN 61000-6-2Harmonics acc. to DIN EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 61800-5-1– Cable exit: Variable– Protection class: I– Product conforming to standards: EN 61800-5-1, CE– Approvals: UL, CSA; CCC, GOST is applied for
D3G 250-ED01 -71
kg
12,0
387
194
392
173
800+20
Ø200
167
90 190
198
218
349
328
180 Ø7
329
298
Electr. connectionp. 42
Core-end sleeves
Centrifugal blowerwith flange
Mas
s of
cent
rifug
al b
low
er
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 17
18
EC centrifugal blowersdual inlet, Ø 250
– Material: Housing: Galvanised sheet steelImpeller: Galvanised sheet steelRotor: Coated in blackElectronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor– Type of protection: IP 54– Insulation class: "B"– Mounting position: Shaft horizontal– Condensate discharges: None– Mode of operation: Continuous operation (S1)– Bearings: Maintenance-free ball bearings
Motor
D3G 250 M3G 112-EA
500 1000 1500 2000 2500 3000
0 [CFM]
[Pa]
40
80
120
160
200
240
280
320
360
0,2
0,4
1,0
[in H
2O]
0,6
0,8
1,2
1,4
[m3/h]
500 1000 1500
5
9
10
11
12
1615
14
13
6
7
8
3
4
2
1
Curves
1~ 230 50/60 1250 720 3,20 100 -25..+40
n[rpm]
P1[W]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
p. 43
L3)
I[A]
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
LwA[dB(A)]
1250
1305
1345
1395
1200
1200
1200
1200
850
850
850
850
500
500
500
500
720
608
516
383
576
472
366
243
205
168
130
86
42
34
27
18
3,20
2,77
2,37
1,79
2,61
2,15
1,68
1,13
0,93
0,76
0,60
0,40
0,19
0,16
0,12
0,08
A 83
81
79
75
82
79
76
71
73
70
67
62
59
55
53
49
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load
VAC Hz rpm W A Pa °C
Curv
e
Nom
inal
vol
tage
Freq
uenc
y
Spee
d/rp
m
Perm
. am
b. te
mp.
Min
. bac
k pr
essu
re
Max
. pow
erin
put(1
)
Max
. cur
rent
draw
(1)
Elec
tr. c
onne
ctio
n
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 18
19
– Technical features: • Line undervoltage detection• PFC (active) • Motor current limitation• Control input 0-10 VDC / PWM • Over-temperature protected electronics / motor• Output 10 VDC max. 10 mA • Locked-rotor protection• Alarm relay • Soft start
– EMC: Interference emission acc. to EN 61000-6-4Interference immunity acc. to EN 61000-6-2Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 61800-5-1– Cable exit: Variable– Protection class: I– Product conforming to standards: CE– Approvals: UL, CSA; CCC, GOST is applied for
D3G 250-EE51 -11
kg
14,2
387
194
392
173
800+20
298
180
328
349
Ø200
165
329
90 190
198
218
Ø7
Electr. connectionp. 43
Core-end sleeves
Centrifugal blowerwith flange
Mas
s of
cent
rifug
al b
low
er
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 19
20
EC centrifugal blowersdual inlet, Ø 250
– Material: Housing: Galvanised sheet steelImpeller: Galvanised sheet steelRotor: Coated in blackElectronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor– Type of protection: IP 54– Insulation class: "B"– Mounting position: Shaft horizontal– Condensate discharges: None– Mode of operation: Continuous operation (S1)– Bearings: Maintenance-free ball bearings
Motor
D3G 250 M3G 112-GA
100
200
300
400
500
0,4
1,2
0,8
1,6
2,0
500 1000 1500 2000 2500 3000 3500
0 [CFM]
[Pa]
[in H
2O]
[m3/h]
500 1000 1500 2000
10
11
12
1615
14
6
7
83
4
2
Curves
3~ 400 50/60 1500 1000 1,70 180 -25..+40
n[rpm]
P1[W]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
p. 44
L4)
I[A]
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
LwA[dB(A)]
---
1500
1570
1635
---
1280
1320
1365
---
990
1010
1035
---
650
655
670
---
1000
874
700
---
599
501
397
---
286
239
185
---
92
80
66
---
86
83
81
---
82
78
76
---
75
72
69
---
64
61
58
---
1,70
1,39
1,15
---
1,01
0,89
0,76
---
0,57
0,49
0,40
---
0,23
0,21
0,19
A
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load
VAC Hz rpm W A Pa °C
Curv
e
Nom
inal
vol
tage
Freq
uenc
y
Spee
d/rp
m
Perm
. am
b. te
mp.
Min
. bac
k pr
essu
re
Max
. pow
erin
put(1
)
Max
. cur
rent
draw
(1)
Elec
tr. c
onne
ctio
n
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 20
21
– Technical features: • Line undervoltage detection• PFC (passive) • Motor current limitation• Control input 0-10 VDC / PWM • Over-temperature protected electronics / motor• Output 10 VDC max. 10 mA • Locked-rotor protection• Alarm relay • Soft start
– EMC: Interference emission acc. to EN 61000-6-3Interference immunity acc. to EN 61000-6-2Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 61800-5-1– Cable exit: Variable– Protection class: I– Product conforming to standards: CE– Approvals: VDE, UL, CSA; CCC, GOST is applied for
D3G 250-EF41 -01
kg
15,8
387
194
392
173
800+20
298
180
328
349
Ø200
165
329
90 190
198
218
Ø7
Electr. connectionp. 44
Core-end sleeves
Centrifugal blowerwith flange
Mas
s of
cent
rifug
al b
low
er
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 21
22
EC centrifugal blowersdual inlet, Ø 283 (10�)
– Material: Housing: Galvanised sheet steelImpeller: Galvanised sheet steelRotor: Coated in blackElectronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor– Type of protection: IP 54– Insulation class: "B"– Mounting position: Shaft horizontal– Condensate discharges: None– Mode of operation: Continuous operation (S1)– Bearings: Maintenance-free ball bearings
Motor
D3G 283 M3G 112-GA
500 1000 1500 2000 2500 3000 3500
0 [CFM]
[Pa]
40
80
120
160
200
240
280
320
360
0,2
0,4
1,0
[in H
2O]
0,6
0,8
1,2
1,4
[m3/h]
500 1000 1500 2000
10
11
12
1615
14
6
7
8
3
4
2
Curves
1~ 230 50/60 1030 750 3,40 150 -25..+40
n[rpm]
P1[W]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
p. 43
L3)
I[A]
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
LwA[dB(A)]
---
1030
1100
1160
---
880
925
955
---
675
695
715
---
435
445
460
---
750
575
378
---
458
326
209
---
209
150
102
---
68
52
40
---
82
78
74
---
78
74
69
---
71
67
61
---
59
53
50
---
3,40
2,61
1,76
---
2,11
1,57
1,22
---
0,99
0,74
0,57
---
0,41
0,32
0,24
A
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load
VAC Hz rpm W A Pa °C
Curv
e
Nom
inal
vol
tage
Freq
uenc
y
Spee
d/rp
m
Perm
. am
b. te
mp.
Min
. bac
k pr
essu
re
Max
. pow
erin
put(1
)
Max
. cur
rent
draw
(1)
Elec
tr. c
onne
ctio
n
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 22
23
– Technical features: • Line undervoltage detection• PFC (active) • Motor current limitation• Control input 0-10 VDC / PWM • Over-temperature protected electronics / motor• Output 10 VDC max. 10 mA • Locked-rotor protection• Alarm relay • Soft start
– EMC: Interference emission acc. to EN 61000-6-4Interference immunity acc. to EN 61000-6-2Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 61800-5-1– Cable exit: Variable– Protection class: I– Product conforming to standards: CE– Approvals: UL, CSA; CCC, GOST is applied for
D3G 283-AB32 -11
kg
18,2
800+20
437215
444
196
386359
326
289
168
Ø225
311
350
Ø9
Electr. connectionp. 43
Core-endsleeves
Centrifugal blowerwith flange
Mas
s of
cent
rifug
al b
low
er
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 23
24
EC centrifugal blowersdual inlet, Ø 283 (10�)
– Material: Housing: Galvanised sheet steelImpeller: Galvanised sheet steelRotor: Coated in blackElectronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor– Type of protection: IP 54– Insulation class: "B"– Mounting position: Shaft horizontal– Condensate discharges: None– Mode of operation: Continuous operation (S1)– Bearings: Maintenance-free ball bearings
Motor
D3G 283 M3G 112-GA
1000 2000 3000 4000
0 [CFM]
[Pa]
100
200
300
400
500
0,4
1,2
[in H
2O]
0,8
1,6
2,0
[m3/h]
500 1000 1500 2000 2500
10
11
12
1615
14
6
7
83
4
2
Curves
3~ 400 50/60 1150 1000 1,80 200 -25..+40
n[rpm]
P1[W]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
p. 44
L4)
I[A]
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
LwA[dB(A)]
---
1150
1260
1385
---
1020
1080
1160
---
805
840
885
---
540
555
575
---
1000
888
566
---
681
528
342
---
341
258
162
---
108
83
57
---
85
83
81
---
81
79
76
---
75
72
68
---
64
62
59
---
1,80
1,44
0,97
---
1,14
0,93
0,67
---
0,66
0,52
0,36
---
0,26
0,22
0,18
A
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load
VAC Hz rpm W A Pa °C
Curv
e
Nom
inal
vol
tage
Freq
uenc
y
Spee
d/rp
m
Perm
. am
b. te
mp.
Min
. bac
k pr
essu
re
Max
. pow
erin
put(1
)
Max
. cur
rent
draw
(1)
Elec
tr. c
onne
ctio
n
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 24
25
– Technical features: • Line undervoltage detection• PFC (passive) • Motor current limitation• Control input 0-10 VDC / PWM • Over-temperature protected electronics / motor• Output 10 VDC max. 10 mA • Locked-rotor protection• Alarm relay • Soft start
– EMC: Interference emission acc. to EN 61000-6-3Interference immunity acc. to EN 61000-6-2Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 61800-5-1– Cable exit: Variable– Protection class: I– Product conforming to standards: CE– Approvals: VDE, UL, CSA; CCC, GOST is applied for
D3G 283-AB37 -01
kg
18,2
800+20
437215
444
196
386359
326
289
168
Ø225
311
350
Ø9
Electr. connectionp. 44
Core-endsleeves
Centrifugal blowerwith flange
Mas
s of
cent
rifug
al b
low
er
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 25
26
EC centrifugal blowersdual inlet, Ø 318 (12�)
– Material: Housing: Galvanised sheet steelImpeller: Galvanised sheet steelRotor: Coated in blackElectronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor– Type of protection: IP 54– Insulation class: "B"– Mounting position: Shaft horizontal– Condensate discharges: None– Mode of operation: Continuous operation (S1)– Bearings: Maintenance-free ball bearings
Motor
D3G 318 M3G 112-GA
1000500 1500 2000 2500 3000 3500 4000
0 [CFM]
[Pa]
50
100
150
200
250
300
350
400
0,2
0,6
[in H
2O]
0,4
0,8
1,0
1,2
1,4
1,6
[m3/h]
500 1000 1500 2000
10
11
12
1615
14
6
7
83
4
Curves
1~ 230 50/60 960 750 3,40 260 -25..+40
n[rpm]
P1[W]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
p. 43
L3)
I[A]
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
LwA[dB(A)]
---
---
960
1050
---
780
830
885
---
610
630
660
---
400
410
425
---
---
750
548
---
563
450
297
---
262
205
140
---
82
66
50
---
---
78
74
---
78
74
70
---
71
67
63
---
59
55
51
---
---
3,40
2,49
---
2,56
2,07
1,39
---
1,22
0,97
0,73
---
0,46
0,37
0,28
A
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load
VAC Hz rpm W A Pa °C
Curv
e
Nom
inal
vol
tage
Freq
uenc
y
Spee
d/rp
m
Perm
. am
b. te
mp.
Min
. bac
k pr
essu
re
Max
. pow
erin
put(1
)
Max
. cur
rent
draw
(1)
Elec
tr. c
onne
ctio
n
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 26
27
– Technical features: • Line undervoltage detection• PFC (active) • Motor current limitation• Control input 0-10 VDC / PWM • Over-temperature protected electronics / motor• Output 10 VDC max. 10 mA • Locked-rotor protection• Alarm relay • Soft start
– EMC: Interference emission acc. to EN 61000-6-4Interference immunity acc. to EN 61000-6-2Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 61800-5-1– Cable exit: Variable– Protection class: I– Product conforming to standards: CE– Approvals: UL, CSA; CCC, GOST is applied for
D3G 318-AA37 -11
kg
20,8
+20
509245
524
232
800
369335
309
340
204
Ø256
Ø9
357
402
Electr. connectionp. 43
Core-end sleeves
Centrifugal blowerwith flange
Mas
s of
cent
rifug
al b
low
er
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 27
28
EC centrifugal blowersdual inlet, Ø 318 (12�)
– Material: Housing: Galvanised sheet steelImpeller: Galvanised sheet steelRotor: Coated in blackElectronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor– Type of protection: IP 54– Insulation class: "B"– Mounting position: Shaft horizontal– Condensate discharges: None– Mode of operation: Continuous operation (S1)– Bearings: Maintenance-free ball bearings
Motor
D3G 318 M3G 112-GA
1000 2000 3000 50004000
0 [CFM]
[Pa]
50
100
150
200
250
300
350
400
0,2
0,6
[in H
2O]
0,4
0,8
1,0
1,2
1,4
1,6
450 1,8
[m3/h]
500 1000 1500 2000 2500
10
11
12
1615
14
6
7
83
2
4
Curves
3~ 400 50/60 880 1000 1,80 100 -25..+40
n[rpm]
P1[W]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
p. 44
L4)
I[A]
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
LwA[dB(A)]
---
880
970
1065
---
775
840
905
---
620
660
695
---
420
440
455
---
1000
797
568
---
635
487
335
---
323
240
158
---
105
78
55
---
83
79
75
---
79
75
71
---
73
69
64
---
62
57
53
---
1,80
1,31
0,99
---
1,08
0,88
0,66
---
0,64
0,50
0,35
---
0,26
0,21
0,18
A
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load
VAC Hz rpm W A Pa °C
Curv
e
Nom
inal
vol
tage
Freq
uenc
y
Spee
d/rp
m
Perm
. am
b. te
mp.
Min
. bac
k pr
essu
re
Max
. pow
erin
put(1
)
Max
. cur
rent
draw
(1)
Elec
tr. c
onne
ctio
n
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 28
29
– Technical features: • Line undervoltage detection• PFC (passive) • Motor current limitation• Control input 0-10 VDC / PWM • Over-temperature protected electronics / motor• Output 10 VDC max. 10 mA • Locked-rotor protection• Alarm relay • Soft start
– EMC: Interference emission acc. to EN 61000-6-3Interference immunity acc. to EN 61000-6-2Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 61800-5-1– Cable exit: Variable– Protection class: I– Product conforming to standards: CE– Approvals: VDE, UL, CSA; CCC, GOST is applied for
D3G 318-AA35 -01
kg
20,8
+20
509245
524
232
800
369335
309
340
204
Ø256
Ø9
357
402
Electr. connectionp. 44
Core-end sleeves
Centrifugal blowerwith flange
Mas
s of
cent
rifug
al b
low
er
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 29
30
EC centrifugal blowersdual inlet, Ø 318 (12�)
– Material: Housing: Galvanised sheet steelImpeller: Galvanised sheet steelRotor: Coated in blackElectronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor– Type of protection: IP 54– Insulation class: "B"– Mounting position: Shaft horizontal– Condensate discharges: None– Mode of operation: Continuous operation (S1)– Bearings: Maintenance-free ball bearings
Motor
D3G 318 M3G 112-GA
1000 2000 3000 4000
0 [CFM]
[Pa]
50
100
150
200
250
300
350
0,2
0,6
[in H
2O]
0,4
0,8
1,0
1,2
1,4
[m3/h]
500 1000 1500 2000 2500
10
11
12
1615
14
6
7
8
3
4
Curves
1~ 230 50/60 900 700 3,20 250 -25..+40
n[rpm]
P1[W]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
p. 43
L3)
I[A]
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
LwA[dB(A)]
---
---
900
970
---
740
780
815
---
575
600
620
---
380
390
400
---
---
700
529
---
562
434
328
---
267
202
148
---
82
65
51
---
---
75
73
---
75
71
69
---
69
64
61
---
57
52
49
---
---
3,20
2,42
---
2,55
1,99
1,58
---
1,24
0,94
0,72
---
0,44
0,34
0,27
A
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load
VAC Hz rpm W A Pa °C
Curv
e
Nom
inal
vol
tage
Freq
uenc
y
Spee
d/rp
m
Perm
. am
b. te
mp.
Min
. bac
k pr
essu
re
Max
. pow
erin
put(1
)
Max
. cur
rent
draw
(1)
Elec
tr. c
onne
ctio
n
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 30
31
– Technical features: • Line undervoltage detection• PFC (active) • Motor current limitation• Control input 0-10 VDC / PWM • Over-temperature protected electronics / motor• Output 10 VDC max. 10 mA • Locked-rotor protection• Alarm relay • Soft start
– EMC: Interference emission acc. to EN 61000-6-4Interference immunity acc. to EN 61000-6-2Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 61800-5-1– Cable exit: Variable– Protection class: I– Product conforming to standards: CE– Approvals: UL, CSA; CCC, GOST is applied for
D3G 318-BB34 -11
kg
22,6
800+20
509245
524
232
446421
386
340
204
Ø256
Ø9
357
402
Electr. connectionp. 43
Core-end sleeves
Centrifugal blowerwith flange
Mas
s of
cent
rifug
al b
low
er
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 31
32
EC centrifugal blowersdual inlet, Ø 318 (12�)
– Material: Housing: Galvanised sheet steelImpeller: Galvanised sheet steelRotor: Coated in blackElectronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor– Type of protection: IP 54– Insulation class: "B"– Mounting position: Shaft horizontal– Condensate discharges: None– Mode of operation: Continuous operation (S1)– Bearings: Maintenance-free ball bearings
Motor
D3G 318 M3G 112-GA
1000 2000 3000 4000 5000
0 [CFM]
[Pa]
50
100
150
200
250
300
350
0,2
0,6
[in H
2O]
0,4
0,8
1,0
1,2
1,4
[m3/h]
500 1000 1500 2000 2500 3000
10
11
12
1615
14
6
7
8 3
2
4
450 1,8
400 1,6
Curves
3~ 400 50/60 880 1000 1,70 150 -25..+40
n[rpm]
P1[W]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
p. 44
L4)
I[A]
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
LwA[dB(A)]
---
880
960
1065
---
770
830
900
---
615
650
690
---
420
435
450
---
1000
813
554
---
645
505
332
---
329
248
157
---
108
82
56
---
62
62
62
---
77
73
70
---
71
66
63
---
60
55
51
---
1,70
1,36
0,97
---
1,10
0,93
0,65
---
0,65
0,51
0,35
---
0,26
0,22
0,18
A
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load
VAC Hz rpm W A Pa °C
Curv
e
Nom
inal
vol
tage
Freq
uenc
y
Spee
d/rp
m
Perm
. am
b. te
mp.
Min
. bac
k pr
essu
re
Max
. pow
erin
put(1
)
Max
. cur
rent
draw
(1)
Elec
tr. c
onne
ctio
n
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 32
33
– Technical features: • Line undervoltage detection• PFC (passive) • Motor current limitation• Control input 0-10 VDC / PWM • Over-temperature protected electronics / motor• Output 10 VDC max. 10 mA • Locked-rotor protection• Alarm relay • Soft start
– EMC: Interference emission acc. to EN 61000-6-3Interference immunity acc. to EN 61000-6-2Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 61800-5-1– Cable exit: Variable– Protection class: I– Product conforming to standards: CE– Approvals: VDE, UL, CSA; CCC, GOST is applied for
D3G 318-BB35 -01
kg
22,4
800+20
509245
524
232
446421
386
340
204
Ø256
Ø9
357
402
Electr. connectionp. 44
Core-end sleeves
Centrifugal blowerwith flange
Mas
s of
cent
rifug
al b
low
er
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 33
34
EC centrifugal blowersdual inlet, Ø 404 (15�)
– Material: Housing: Galvanised sheet steelImpeller: Galvanised sheet steelRotor: Coated in blackElectronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor– Type of protection: IP 54– Insulation class: "F"– Mounting position: Shaft horizontal– Condensate discharges: Rotor-side– Mode of operation: Continuous operation (S1)– Bearings: Maintenance-free ball bearings
Motor
D3G 404 M3G 150-NA
2000 4000 6000 8000
0 [CFM]
[Pa]
100
200
300
400
500
600
0,8
[in H
2O]
0,4
1,2
1,6
2,0
2,4
[m3/h]
1000 2000 3000 4000 5000
10
1112
16 1514
6
78
3
2
13
5
9
1
4700 2,8
Curves
3~ 400 50/60 1000 3000 4,80 300 -25..+40
n[rpm]
P1[W]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
p. 45
M1)
I[A]
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
LwA[dB(A)]
1000
1065
1120
1180
900
900
900
900
700
700
700
700
500
500
500
500
3000
2647
2116
1341
2108
1603
1095
596
992
754
515
281
361
275
188
102
91
89
86
83
88
85
81
77
81
77
74
71
72
69
65
61
4,80
4,00
3,21
2,06
3,18
2,42
1,66
0,92
1,50
1,14
0,78
0,43
0,55
0,42
0,29
0,16
A
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load
VAC Hz rpm W A Pa °C
Curv
e
Nom
inal
vol
tage
Freq
uenc
y
Spee
d/rp
m
Perm
. am
b. te
mp.
Min
. bac
k pr
essu
re
Max
. pow
erin
put(1
)
Max
. cur
rent
draw
(1)
Elec
tr. c
onne
ctio
n
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 34
35
– Technical features: • Line undervoltage / phase failure detection• PFC (passive) • Motor current limitation• Control input 0-10 VDC / PWM • Over-temperature protected electronics / motor• Output 10 VDC max. 10 mA • Locked-rotor protection• Alarm relay • Soft start
– EMC: Interference emission acc. to EN 61000-6-3Interference immunity acc. to EN 61000-6-2Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 61800-5-1– Cable exit: Variable– Protection class: I– Product conforming to standards: CE– Approvals: VDE, UL, CSA; CCC, GOST is applied for
D3G 404-AA02 -03
kg
52,9
Electr. connectionp. 45
Core-end sleeves
Centrifugal blowerwith flange
Mas
s of
cent
rifug
al b
low
er
583273
531
45.5
46046.5
274
641
800 +20
374402432
Ø10
125
429
454
Ø309
255
406
125370400422
Ø8
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 35
36
EC centrifugal blowersdual inlet, Ø 404 (15�)
– Material: Housing: Galvanised sheet steelImpeller: Galvanised sheet steelRotor: Coated in blackElectronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor– Type of protection: IP 54– Insulation class: "F"– Mounting position: Shaft horizontal– Condensate discharges: Rotor-side– Mode of operation: Continuous operation (S1)– Bearings: Maintenance-free ball bearings
Motor
D3G 404 M3G 150-NA
2000 4000 6000 8000
0 [CFM]
[Pa]
100
200
300
400
500
600
0,8
[in H
2O]
0,4
1,2
1,6
2,0
2,4
[m3/h]
1000 2000 3000 4000 5000
1011
12
16 1514
6
78
3
2
13
5
9
1
4700 2,8
Curves
3~ 400 50/60 1000 3000 4,80 375 -25..+40
n[rpm]
P1[W]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
p. 45
M1)
I[A]
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
LwA[dB(A)]
1000
1055
1125
1180
800
800
800
800
650
650
650
650
500
500
500
500
3000
2705
2007
1407
1445
1152
682
447
787
623
376
259
360
294
186
133
89
86
84
84
82
79
75
74
76
74
69
69
70
67
64
63
4,80
4,12
3,06
2,16
2,20
1,78
1,10
0,79
1,25
1,02
0,69
0,51
0,69
0,57
0,39
0,30
A
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load
VAC Hz rpm W A Pa °C
Curv
e
Nom
inal
vol
tage
Freq
uenc
y
Spee
d/rp
m
Perm
. am
b. te
mp.
Min
. bac
k pr
essu
re
Max
. pow
erin
put(1
)
Max
. cur
rent
draw
(1)
Elec
tr. c
onne
ctio
n
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 36
37
– Technical features: • Line undervoltage / phase failure detection• PFC (passive) • Motor current limitation• Control input 0-10 VDC / PWM • Over-temperature protected electronics / motor• Output 10 VDC max. 10 mA • Locked-rotor protection• Alarm relay • Soft start
– EMC: Interference emission acc. to EN 61000-6-3Interference immunity acc. to EN 61000-6-2Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 61800-5-1– Cable exit: Variable– Protection class: I– Product conforming to standards: CE– Approvals: VDE, UL, CSA; CCC, GOST is applied for
D3G 404-BB02 -03
kg
56,5
Electr. connectionp. 45
Core-end sleeves
Centrifugal blowerwith flange
Mas
s of
cent
rifug
al b
low
er
583
641
274
46.5 460
45.5
531
273
800 +20
523500470375
429
454
474502532
Ø309
255
406
125 Ø8
125
Ø10
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 37
38
EC centrifugal blowersdual inlet, Ø 454 (18�)
– Material: Housing: Galvanised sheet steelImpeller: Galvanised sheet steelRotor: Coated in blackElectronics enclosure: Die-cast aluminium
– Direction of rotation: Clockwise, seen on rotor– Type of protection: IP 54– Insulation class: "F"– Mounting position: Shaft horizontal– Condensate discharges: Rotor-side– Mode of operation: Continuous operation (S1)– Bearings: Maintenance-free ball bearings
Motor
D3G 454 M3G 150-NA
2000 4000 6000 8000 10000 12000
0 [CFM]
[Pa]
50
100
150
300
350
400
0,4
[in H
2O]
0,2
0,6
200 0,8
250 1,0
1,2
1,4
1,6
[m3/h]
1000 2000 3000 4000 5000 6000 7000
10
11
12
16
15
14
6
7
8
3
2
4450 1,
8
500 2,0
550 2,2
Curves
3~ 400 50/60 660 2900 4,50 150 -25..+40
n[rpm]
P1[W]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
p. 45
M1)
I[A]
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
LwA[dB(A)]
---
660
715
790
---
615
665
720
---
500
525
555
---
355
365
385
---
2900
2414
1759
---
2225
1813
1251
---
1123
875
574
---
400
308
209
---
89
85
81
---
86
83
78
---
81
77
72
---
72
67
62
---
4,50
4,20
3,20
---
3,38
2,76
1,91
---
1,73
1,37
0,95
---
0,74
0,60
0,43
A
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load
VAC Hz rpm W A Pa °C
Curv
e
Nom
inal
vol
tage
Freq
uenc
y
Spee
d/rp
m
Perm
. am
b. te
mp.
Min
. bac
k pr
essu
re
Max
. pow
erin
put(1
)
Max
. cur
rent
draw
(1)
Elec
tr. c
onne
ctio
n
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 38
39
– Technical features: • Line undervoltage / phase failure detection• PFC (passive) • Motor current limitation• Control input 0-10 VDC / PWM • Over-temperature protected electronics / motor• Output 10 VDC max. 10 mA • Locked-rotor protection• Alarm relay • Soft start
– EMC: Interference emission acc. to EN 61000-6-3Interference immunity acc. to EN 61000-6-2Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3.5 mA acc. to EN 61800-5-1– Cable exit: Variable– Protection class: I– Product conforming to standards: CE– Approvals: VDE, UL, CSA; CCC, GOST is applied for
D3G 454-AA07 -03
kg
61,5
Electr. connectionp. 45
Core-end sleeves
Centrifugal blowerwith flange
Mas
s of
cent
rifug
al b
low
er
56.5
641
700321
800+20
55356.5
331
773
478455423125
428462498
480
310
Ø381
Ø10
125
395
505
532
Ø8
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 39
40
Electrical connections EC
+
-
+
-
H1) EC motors (size 055, line-fed)
Speed setting
PWM 1 - 10 kHz
Speed settingwith variable resistance
Full speed
100% PWM -> n=maxapprox. 10% PWM -> n=min
< 10% PWM -> n=0
start up at > 1.4 V
Speed setting
1 V - 10 V
10 V -> n=maxapprox. 1 V -> n=min
< 1 V -> n=0
start up at > 1.4 V
10 K
PWM
12 V
U
Speed display
Alarm
Controller
Counter
yellow
white
blue
Lin/PWM control input0-10 VDC / PWM
green/yellowPE
blueNbrownL
red
Voltage output+10 V max. 1.1 mA
Tach output1 pulse per revolution
GND
Isink max. 10 mA
680 Ω47 V
Customer circuit
Notes on various control possibilities and their applications
Connection Fan
Imax =10 mA
Umin = 15 V
1 μF
Mains50/60 Hz
L PEN
Line Connection Colour Assignment / function Line Connection Colour Assignment / function1 2L brown Mains 50/60 Hz, phase +10 V red
0-10 V / PWM yellow Control input (Impedance 100 kΩ)N blue Mains 50/60 Hz, neutral
PE green/yel Protective earth
Line 1
brown green/yellowblue
+10
V
0-10
VPW
M
Line 2
red yellow
Voltage output +10 V max. 1.1 mA
GND blue
Tach white Tach output: 1 pulse per revolution
GND
Tach
GND
whiteblue
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 40
41
+
-
+
-
J1) EC motors (size 074, line-fed)
Speed setting
PWM 1 - 10 kHz
Speed settingwith variable resistance
Full speed
100% PWM -> n=maxapprox. 10% PWM -> n=min
< 10% PWM -> n=0
start up at > 1.4 V
Speed setting
1 V - 10 V
10 V -> n=maxapprox. 1 V -> n=min
< 1 V -> n=0
start up at > 1.4 V
10 K
PWM
12 V
U
Speed display
Alarm
Controller
Counter
yellow
white
blue
Lin/PWM control input0-10 VDC / PWM
green/yellowPE
blueNblackL
red
Voltage output+10 V max. 1.1 mA
Tach output1 pulse per revolution
GND
Isink max. 10 mA
680 Ω47 V
Customer circuit
Notes on various control possibilities and their applications
Connection Fan
Imax =10 mA
Umin = 15 V
1 μF
Mains50/60 Hz
L PEN
Line Connection Colour Assignment / function Line Connection Colour Assignment / function1 2L black Mains 50/60 Hz, phase +10 V red
0-10 V / PWM yellow Control input (Impedance 100 kΩ)N blue Mains 50/60 Hz, neutral
PE green/yel Protective earth
Line 1
black green/yellowblue
+10
V
0-10
VPW
M
Line 2
red yellow
Voltage output +10 V max. 1.1 mA
GND blue
Tach white Tach output: 1 pulse per revolution
GND
Tach
GND
whiteblue
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 41
42
Electrical connections EC
+
-
+
-
K1) EC motors (size 084, line-fed)
white1NC
white2COM
Speed setting
PWM 1 - 10 kHz
Speed settingwith variable resistance
Full speed
100% PWM -> n=maxapprox. 10% PWM -> n=min
< 10% PWM -> n=0
start up at > 1.4 V
Speed setting
1 V - 10 V
10 V -> n=maxapprox. 1 V -> n=min
< 1 V -> n=0
start up at > 1.4 V
10 K
PWM
12 V
U
yellow
blue
Lin/PWM control input
0-10 VDC /PWM
green/yellowPEblueNblackL
redVoltage output
+10 V max. 1.1 mA
GND
Customer circuit
Notes on various control possibilities and their applications
Connection Fan
Imax =10 mA
Umin = 15 V
1 μF
Mains50/60 Hz
Alarm relay:Break for failure(2 A, 250 VAC, AC1)
L PEN
Line Connection Colour Assignment / function Line Connection Colour Assignment / function1 2L black Mains 50/60 Hz, phase +10 V red
0-10 V / PWM yellow Control input (Impedance 100 kΩ)N blue Mains 50/60 Hz, neutral
PE green/yel Protective earth
Line 1
black green/yellowblue
+10
V
0-10
VPW
M
Line 2
red yellow
Voltage output +10 V max. 1.1 mA
NC white1 Alarm relay, break for failure
COM white2 Alarm relay, COMMON
GND blue GND
NC GND
white1
COM
white2 blue
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 42
43
speedFull
potentiometerwithSpeed setting
<1 V -> n = 01 V -> n = min
10 V -> n = max
settingSpeed
1-10 V
10 K
47 K
Imax=10 mA10
47 K
PE1
A1A2
1114
P
NAC2
AC1
10 A (T)
470 nF
L
N
GND
PE
10 V
P
0-10 V
COM
NC
8
8
8 8
6
5
4
3
2
12
12
12
11
11
1110 V
10
0 V
0-10 V
L3) EC motors (size 112, single-phase mains-powered)
Customer circuit Connection Fan
NPE
Line Connection Colour Assignment / function1 PE green/yellow Protective earth
1
1
1
N blue Mains 50/60 Hz, neutral
Line 1
blackblue
0-10
V
P
Line 2
yellow orange
L black Mains 50/60 Hz, phase
COM white1 Alarm relay, COMMON (2A, max. 250 VAC, min. 10 mA, AC1)
L
+10
V
COM
white1 red
NC
white2green/yellow
GND
blue
No.2
3
4
5
1 NC white2 Alarm relay, break for failure6
2 0-10 V yellow Control input (Impedance 100 kΩ), SELV8
2 P orange not designated10
2 +10 V red Voltage output 10 VDC (+/- 3%), max. 10 mA, supply voltage for external units (e.g. potentiometer), SELV11
2 GND blue GND, SELV12
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 43
44
Electrical connections EC
speedFull
potentiometerwithSpeed setting
<1 V -> n = 01 V -> n = min
10 V -> n = max
settingSpeed
1-10 V
10 K
47 K
Imax=10 mA
47 K
PE1
A1A2
1114
P
NAC3AC2AC1
470 nF
L3
L2
L1
GND
PE
+10 V
P
0-10 V
COM
NC
8
8
8
8
7
6
5
4
3
2
12
12
12
11
11
11
10 V
10
0 V
0-10 V
L4) EC motors (size 112, three-phase mains-powered)
PE L2L1
Line Connection Colour Assignment / function1 PE green/yellow Protective earth
1
1
1
L1 black Mains 50/60 Hz, phase
Line 1
blackgreen/yellow black
0-10
V
P
Line 2
yellow orange
L3 black Mains 50/60 Hz, phase
COM white1 Alarm relay, COMMON (2A, max. 250 VAC, min. 10 mA, AC1)
L3
+10
V
COM
white1 red
NC
white2black
GND
blue
No.2
3
5
6
1 NC white2 Alarm relay, break for failure7
2 0-10 V yellow Control input (Impedance 100 kΩ), SELV8
2 P orange not designated10
2 +10 V red Voltage output 10 VDC (+/- 3%), max. 10 mA, supply voltage for external units (e.g. potentiometer), SELV11
2 GND blue GND, SELV12
1 L2 black Mains 50/60 Hz, phase4
Customer circuit Connection Fan
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 44
45
speedFull
potentiometerwithSpeed setting
<1 V -> n = 01 V -> n = min
10 V -> n = max
settingSpeed
1-10 V
10 K
47 K
Imax=10 mA33
47 K
PE1
A1A2
1114
P
NAC3AC2AC1
2,2 μF
L3
L2
L1
GND
PE
+10 V
0-10 V
COM
NC
8
8
8
8
7
6
5
4
3
2
12
12
12
11
11
11 10 V
0 V
RSB
RSA
14
13 RSA
RSB
0-10 V
M1) EC motors (size 150, three-phase mains-powered)
PE L2L1
Line Connection Colour Assignment / function1 PE green/yellow Protective earth
1
1
1
L1 black Mains 50/60 Hz, phase
Line 1
blackgreen/yellow black
0-10
V
+10
V
Line 2
yellow red
L3 black Mains 50/60 Hz, phase
COM white1 Alarm relay, COMMON (2A, max. 250 VAC, min. 10 mA, AC1)
L3 GND
COM
white1 blue
NC
white2black
RSA
No.2
3
5
6
1 NC white2 Alarm relay, break for failure7
2 0-10 V yellow Control input (Impedance 100 kΩ), SELV8
2 +10 V red Voltage output 10 VDC (+/- 3%), max. 10 mA, supply voltage for external units (e.g. potentiometer), SELV11
2 GND blue GND, SELV12
1 L2 black Mains 50/60 Hz, phase4
2 RSA orange RS485 interface for ebmBUS; RSA, SELV13
2 RSB black RS485 interface for ebmBUS; RSB, SELV14
RSB
blackorange
Customer circuit Connection Fan
D3G_englisch:Axial_D 30.04.2008 10:58 Seite 45
46
KoblenzWinfried SchaeferHinter der Kirch 10D-56767 UersfeldPhone +49 (0) 26 57 / 16 96Fax +49 (0) 26 57 / 16 76Winfried.Schaefer@de.ebmpapst.com
MunichDipl.-Wirt.-Ing. (FH) Jens Peter Steinbergweg 6D-82285 HattenhofenPhone +49 (0) 81 45 / 80 92 25Fax +49 (0) 81 45 / 80 92 26Jens.Peter@de.ebmpapst.com
NurembergFriedrich KleinAdlerstraße 49/1D-73540 HeubachPhone +49 (0) 71 73 / 49 83Fax +49 (0) 71 73 / 80 53Friedrich.Klein@de.ebmpapst.com
OffenburgDipl.-Ing (FH) Ralf BraunHubeneck 21D-77704 OberkirchPhone +49 (0) 78 02 / 98 22 52Fax +49 (0) 78 02 / 98 22 53Ralf.Braun@de.ebmpapst.com
StuttgartDipl.-Ing. (FH) Rudi WeinmannHindenburgstraße 100/1D-73207 PlochingenPhone +49 (0) 71 53 / 92 89 80Fax +49 (0) 71 53 / 92 89 81Rudi.Weinmann@de.ebmpapst.com
UlmGünter WilhelmAllgäuer Straße 7D-89269 VöhringenPhone +49 (0) 73 06 / 92 46 08Fax +49 (0) 73 06 / 92 46 48Guenter.Wilhelm@de.ebmpapst.com
Distributors
FrankfurtR.E.D. Handelsgesellschaft mbHGutenbergstraße 3D-63110 Rodgau - JügesheimPhone +49 (0) 61 06 / 84 10Fax +49 (0) 61 06 / 84 11 11info@red-elektromechanik.dewww.red-elektromechanik.de
HamburgBreuell + Hilgenfeldt GmbHGrützmühlenweg 40D-22339 HamburgPhone +49 (0) 40 / 53 80 92 20Fax +49 (0) 40 / 53 80 92 84info@breuell.de
MunichA. Schweiger GmbHOhmstraße 1D-82054 SauerlachPhone +49 (0) 81 04 / 8 97 0Fax +49 (0) 81 04 / 8 97 90info@schweiger-gmbh.dewww.schweiger-gmbh.com
(1 to 5 pieces)
NorthBreuell + Hilgenfeldt GmbHGrützmühlenweg 40D-22339 HamburgPhone +49 (0) 40 / 53 80 92 20Fax +49 (0) 40 / 53 80 92 84ebm@breuell.de
SouthHDS Ventilatoren Vertriebs GmbHGlaswiesenstraße 1D-74677 DörzbachPhone +49 (0) 79 37 / 80 29 68Fax +49 (0) 79 37 / 80 25 78info@hds-gmbh.net
Agencies
BerlinDipl.-Ing. (TH) Jens DuchowHändelstraße 7D-16341 PanketalPhone +49 (0) 30 / 94 41 49 62Fax +49 (0) 30 / 94 41 49 63Jens.Duchow@de.ebmpapst.com
DortmundDipl.-Ing. (FH) Hans-Joachim PundtAuf den Steinern 3D-59519 Möhnesee-VöllinghausenPhone +49 (0) 29 25 / 80 04 07Fax +49 (0) 29 25 / 80 04 08Hans-Joachim.Pundt@de.ebmpapst.com
FrankfurtDipl.-Ing. Christian KleffmannDr. Hermann-Krause Straße 23D-63452 HanauPhone +49 (0) 61 81 / 18 98 12Fax +49 (0) 61 81 / 18 98 13Christian.Kleffmann@de.ebmpapst.com
HalleDipl.-Ing. (TU) Michael HanningLerchenweg 4D-06120 LieskauPhone +49 (0) 3 45 / 5 51 24 56Fax +49 (0) 3 45 / 5 51 24 57Michael.Hanning@de.ebmpapst.com
HamburgIngenieurbüro Breuell GmbHDirk KahlElektroingenieurGrützmühlenweg 40D-22339 HamburgPhone +49 (0) 40 / 53 80 92 10Fax +49 (0) 40 / 53 80 92 84Dirk.Kahl@de.ebmpapst.com
KasselDipl.-Ing. (FH) Ralph BrückHoherainstraße 38D-35075 GladenbachPhone +49 (0) 64 62 / 40 71 10Fax +49 (0) 64 62 / 40 71 11Ralph.Brueck@de.ebmpapst.com
Distributors, agencies and subsidiaries
Germany
ebm-papstMulfingen GmbH & Co. KG
Bachmühle 2D-74673 MulfingenPhone +49 (0) 79 38 / 81-0Fax +49 (0) 79 38 / 81-110info1@de.ebmpapst.com
www.ebmpapst.com
ebm-papstSt. Georgen GmbH & Co. KG
Hermann-Papst-Straße 1D-78112 St. GeorgenPhone +49 (0) 77 24 / 81-0Fax +49 (0) 77 24 / 81-13 09info2@de.ebmpapst.com
www.ebmpapst.com
ebm-papstLandshut GmbH
Hofmark-Aich-Straße 25D-84030 LandshutPhone +49 (0) 8 71 / 707-0Fax +49 (0) 8 71 / 707-465info3@de.ebmpapst.com
www.ebmpapst.com
fan agent
compact fan agent
motor specialist
motor agent
D3G_englisch:Axial_D 30.04.2008 10:59 Seite 46
47
Europe
Austriaebm-papst Motoren & Ventilatoren GmbHWestbahnstraße 5A-4490 St. FlorianPhone +43 / 72 24 / 66 01 10Fax +43 / 72 24 / 66 01 120info@at.ebmpapst.comwww.ebmpapst.at
Belarusebm-papst Bel AgmbHProspekt Nesavisimosti 11/2 Zimmer 325, 512BY-220050 MinskPhone +375 / 17 / 209 95 61Fax +375 / 17 / 209 95 61info@by.ebmpapst.com
BelgiumVIBO Benelux B. V.Sales office Belgium-LuxemburgRomeinsestraat 6/0101Research Park HaasrodeB-3001 Heverlee-LeuvenPhone +32 / 16 / 39 62 00Fax +32 / 16 / 39 62 20info@vibobenelux.comwww.vibobenelux.com
Bulgariaebm-papst Romania S.R.L.Str. Tirnavei Nr. 20RO-500327 BrasovPhone +40 / 268 / 312 805Fax +40 / 268 / 312 805dudasludovic@xnet.ro
Croatiaebm-papst Industries Kft.Ezred u. 2.H-1044 BudapestPhone +36 / 1 / 87 22 190Fax +36 / 1 / 87 22 194office@hu.ebmpapst.comwww.ebmpapst.hu
CyprusMATERO LTD37, St. Kyriakides AvenueP.O. Box 51744CY-3080 LimassolPhone +357 / 25 / 87 00 30Fax +357 / 25 / 38 13 66matero@cytanet.com.cywww.matero.com.cy
Czech Republic / Slovakiaebm-papst CZ s.r.o.Krátká 379CZ-66461 Rajhradice u BrnaPhone +420 / 5 / 47 23 26 16Fax +420 / 5 / 47 23 26 22info@ebmpapst.czwww.ebmpapst.cz
DenmarkJenk A/SVallensbækvej 21DK-2605 BrøndbyPhone +45 / 43 / 63 11 11Fax +45 / 43 / 63 05 05jenk@jenk.dkwww.jenk.dk
Estoniaebm-papst Oy Eesti FiliaalKadaka tee 3EST-10621 TallinnPhone +372 / 65 56 / 978Fax +372 / 65 56 / 979www.ebmpapst.ee
Finlandebm-papst OyPuistotie 1FIN-02760 EspooPhone +358 / 9 / 88 70 22 0Fax +358 / 9 / 88 70 22 13mailbox@ebmpapst.fiwww.ebmpapst.fi
Franceebm-papst SARLZI Nord - rue A. MohlerBP 62F-67212 Obernai-CedexPhone +33 / 820 326 266Fax +33 / 3 / 88 67 38 83info@ebmpapst.frwww.ebmpapst.fr
GreeceHelcomaTh. Rotas & Co OEDavaki 65GR-17672 Kallithea-AttikiPhone +30 / 210 / 951 37 05Fax +30 / 210 / 951 34 90contact@helcoma.grwww.helcoma.gr
Hungaryebm-papst Industries Kft.Ezred u. 2.H-1044 BudapestPhone +36 / 1 / 87 22 190Fax +36 / 1 / 87 22 194office@hu.ebmpapst.comwww.ebmpapst.hu
IcelandRJ EngineersStangarhyl 1AIS-110 ReykjavikPhone +354 / 567 80 30Fax +354 / 567 80 15rj@rj.iswww.rj.is
Irelandebm-papst LimitedPortlaoise Business & Technology ParkMountrath RoadIRL-Portlaoise, Co. LaoisPhone +353 / 57 86 / 643 43Fax +353 / 57 86 / 643 46sales@ie.ebmpapst.comwww.ebmpapst.ie
Italyebm-papst SrlVia Cornaggia 108I-22076 Mozzate (Co)Phone +39 / 03 31 / 83 62 01Fax +39 / 03 31 / 82 15 10info@it.ebmpapst.comwww.ebmpapst.it
Macedoniaebm-papst Industries Kft.Ezred u. 2.H-1044 BudapestPhone +36 / 1 / 87 22 190Fax +36 / 1 / 87 22 194office@hu.ebmpapst.comwww.ebmpapst.hu
D3G_englisch:Axial_D 30.04.2008 10:59 Seite 47
48
Russiaebm-papst Ural GmbHRosa Luxemburg Strasse 59RU-620026 JekaterinburgPhone +7 / 343 / 378 31 75Fax +7 / 343 / 378 31 89Konstantin.Molokov@ru.ebmpapst.comwww.ebmpapst.ur.ru
ebm-papst Rus GmbHNizhegorodskaya 32, str. 15 office 420RU-109029 MoskauPhone +7 / 495 / 671 53 93Fax +7 / 495 / 671 53 95info@ebmpapst.ruwww.ebmpapst.ru
ebm-papst RusSaint-Petersburg´s FilialZastavskaya 7RU-196084 Sankt-PetersburgPhone +7 / 812 / 449 96 07Fax +7 / 812 / 449 96 07spb@ru.ebmpapst.com
Serbia & Montenegroebm-papst Industries Kft.Ezred u. 2.H-1044 BudapestPhone +36 / 1 / 87 22 190Fax +36 / 1 / 87 22 194office@hu.ebmpapst.comwww.ebmpapst.hu
Spainebm-papst Ibérica S.L.Avda. del Sistema Solar, 29E-28830 San Fernando de Henares (Madrid)Phone +34 / 91 / 678 08 94Fax +34 / 91 / 678 15 30ventas@ebmpapst.es
Swedenebm-papst ABÄggelundavägen 2S-17562 JärfällaPhone +46 / 8 / 761 94 00Fax +46 / 8 / 36 23 06info@ebmpapst.sewww.ebmpapst.se
Switzerlandebm-papst AGRütisbergstraße 1CH-8156 OberhasliPhone +41 / 44 / 732 20 70Fax +41 / 44 / 732 20 77verkauf@ebmpapst.chwww.ebmpapst.ch
TurkeyAkantel Elektronik San. Tic. LTD. Sti.Atatürk Organize SanayiBölgesi 10007 SK. No.:6TR-35620 Cigli-IzmirPhone +90 / 2 32 / 32 82 090 -91Fax +90 / 2 32 / 32 80 270akantel@akantel.com.trwww.akantel.com.tr
Ukraineebm-papst Ukraine LLCLepse Boulevard, 4, Building 47UA-03067 KievPhone +38 / 044 / 206 30 91Fax +38 / 044 / 206 30 91mail@ebmpapst.uawww.ebmpapst.ua
United Kingdomebm-papst UK Ltd.Chelmsford Business ParkGB-Chelmsford Essex CM2 5EZPhone +44 / 12 45 / 46 85 55Fax +44 / 12 45 / 46 63 36sales@uk.ebmpapst.comwww.ebmpapst.co.uk
ebm-papst Automotive & Drives (UK) Ltd.The SmithyFidlers Lane, East IlsleyGB-Berkshire RG20 7LGPhone +44 / 87 07 / 66 51 70Fax +44 / 87 07 / 66 51 80A&Dsales@uk.ebmpapst.comwww.ebmpapst-ad.com
NetherlandsVIBO Benelux B. V.Engelseweg 127Postbus 230NL-5705 AC HelmondPhone +31 / 4 92 / 50 29 00Fax +31 / 4 92 / 50 29 50verkoop@vibobenelux.comwww.vibobenelux.com
Norwayebm-papst ASP.B. 173 HolmliaN-1203 OsloPhone +47 / 22 / 76 33 40Fax +47 / 22 / 61 91 73mailbox@ebmpapst.nowww.ebmpapst.no
Polandebm-papst Polska Sp. z o.o.ul. Annopol 4APL-03236 WarszawaPhone +48 / 22 / 675 78 19Fax +48 / 22 / 676 95 87office@ebmpapst.plwww.ebmpapst.pl
Portugalebm-papst (Portugal), Lda.Av. Marechal Gomes da Costa, 35 eRua Conselheiro Emidio NavarroP-1800-255 LisboaPhone +351 / 21 / 839 48 80Fax +351 / 21 / 839 47 59info@pt.ebmpapst.com
Romaniaebm-papst Romania S.R.L.Str. Tirnavei Nr. 20RO-500327 BrasovPhone +40 / 268 / 312 805Fax +40 / 268 / 312 805dudasludovic@xnet.ro
Distributors, agencies and subsidiariesfan agent
compact fan agent
motor specialist
motor agent
D3G_englisch:Axial_D 30.04.2008 10:59 Seite 48
49
America
Argentinaebm-papst de Argentina S.A.Hernandarias 148 Lomas del MiradorPcia. de Buenos Aires (1752)Phone +54 / 11 46 57 61 35Fax +54 / 11 46 57 20 92ventas@ar.ebmpapst.com
Brasilebm-papst Motores Ventiladores Ltda.Av. José Giorgi, 301 Galpões B6+B7Condominio Logical CenterBR-06707-100 Cotia - São PauloPhone +55 /11 / 31 64 89 00Fax +55 /11 / 47 77 14 56vendas@br.ebmpapst.comwww.ebmpapst.com.br
Canadaebm-papst Canada Inc.1800 Ironstone Manor, Unit 2CDN-Pickering, Ontario, L1W3J9Phone +1 / 905 / 420 / 35 33Fax +1 / 905 / 420 / 37 72sales@ca.ebmpapst.comwww.ebmpapst.ca
Mexicoebm Industrial S.de R.L. de C.V.Paseo de Tamarindos 400-A-5to PisoCol. Bosques de las LomasMEX-Mexico 05120, D.F.Phone +52 / 55 / 50 91 44 44Fax +52 / 55 / 50 91 44 43sales@mx.ebmpapst.comwww.ebmpapst.com.mx
USAebm-papst Inc.P.O. Box 4009100 Hyde RoadUSA-Farmington, CT 06034Phone +1 / 860 / 674 15 15Fax +1 / 860 / 674 85 36sales@us.ebmpapst.comwww.ebmpapst.us
ebm-papst Automotive & Drives, Inc.3200 Greenfield, Suite 255USA-Dearborn, MI 48120Phone +1 / 313 / 406 80 80Fax +1 / 313 / 406 80 81automotive@us.ebmpapst.comwww.ebmpapst-automotive.us
Africa
South Africaebm-papst South Africa (Pty) Ltd.P.O. Box 31241119 Yacht AvenueZA-2040 HoneydewPhone +27 / 11 / 794 34 34Fax +27 / 11 / 794 50 20info@za.ebmpapst.comwww.ebmpapst.co.za
D3G_englisch:Axial_D 30.04.2008 10:59 Seite 49
50
Distributors, agencies and subsidiaries
Asia
Chinaebm-papst Ventilator (Shanghai) Co., Ltd.No. 418, Huajing RoadWaiGaoQiao Free Trade ZoneNo. 2001, Yang Gao (N) RoadVRC-200131 Shanghai, P.R. of ChinaPhone +86 / 21 / 50 46 01 83Fax +86 / 21 / 50 46 11 19sales@cn.ebmpapst.com
Hong Kongebm-papst Ventilator (Shanghai) Co., Ltd.Hong Kong Representative OfficeUnit Nos. 13, 9/F, Technology Park18 On Lai Street, Sha Tin, N.T.HK-Hong Kong P.R. of ChinaPhone +852 / 21 45 / 86 78Fax +852 / 21 45 / 76 78chenghong@cn.ebmpapst.com
Indiaebm NADI International Pvt Ltd.26/3, G.N.T. Road, ErukkencherryIND-Chennai-600118Phone +91 / 44 / 25 37 25 56Fax +91 / 44 / 25 37 11 49ebmnadi@md2.vsnl.net.inwww.ebmnadi.com
Indonesiaebm-papst IndonesiaWisma Slipi, Jl. Letjend S. Parman Kav. 1214th Floor, No. 1410RI-Jakarta Barat 11480Phone +62 / 21 / 536 619 01Fax +62 / 21 / 536 619 05sonny.sanjaya@id.ebmpapst.com
IsraelPolak Bros. Import Agencies Ltd.9 Hamefalsim StreetIL-Kiryat Arie, Petach-Tikva 49514Phone +972 / 3 / 910 03 00Fax +972 / 3 / 579 66 79polak@polak.co.ilwww.polak.co.il
Japanebm-papst Industries Japan K.K.12 Floor, Benex S-3 Bldg.3-20-8 Shinyokohama, Kohoku-kuJ-222-0033 YokohamaPhone +81 / 45 / 470 / 57 51Fax +81 / 45 / 470 / 57 52info@jp.ebmpapst.comwww.ebmpapst.jp
Koreaebm-papst Korea Co. Ltd.6F, Trutec Bldg.B 6-2, Digital Media City (DMC)Sangam-Dong, Mapo-Gu ROK-Seoul 121-270Phone +82 / 2 / 36 62 / 13 24Fax +82 / 2 / 36 62 / 13 26info@kr.ebmpapst.com www.ebmpapst.co.kr
Malaysiaebm-papst MalaysiaRepresentative OfficeBlock F1, 9A-4, Jalan PJU 1/42Dataran PrimaMAL-47301 Petaling JayaPhone +60 / 3 / 78 06 54 40Fax +60 / 3 / 78 06 54 41john.bulder@my.ebmpapst.com
Singaporeebm-papst SEA Pte. Ltd.23 Ubi Road 4, #05-00Olympia Industrial BuildingSGP-Singapore 408620Phone +65 / 68 42 84 38Fax +65 / 68 42 84 39salesdept@sg.ebmpapst.com
TaiwanETECO Engineering & Trading Corp.10F-I, No. 92, Teh-Wei Str.RC-Tsow-Inn District, KaohsiungPhone +886 / 7 / 557 42 68Fax +886 / 7 / 557 27 88eteco@ms22.hinet.net
Thailandebm-papst Thailand Co. Ltd.Representative Office99/349 Chaeng Wattana Road, LaksiBangkok 10210, ThailandPhone +66 / 2 / 576 / 15 24-5Fax +66 / 2 / 576 / 15 42salesdept@th.ebmpapst.com
United Arab Emiratesebm-papst Middle East FZEPO Box 17755Jebel Ali Free Zone / FZS1 / AP05UAE-DubaiPhone +971 / 4 / 886 08 26Fax +971 / 4 / 886 08 27info@ae.ebmpapst.com
fan agent
compact fan agent
motor specialist
motor agent
D3G_englisch:Axial_D 30.04.2008 10:59 Seite 50
51
Australia
Australiaebm-papst Australia Pty Ltd.2 Silverton CloseAUS-Laverton North, Victoria, 3026Phone +61 / 3 / 83 25 64 00Fax +61 / 3 / 83 25 64 64sales@ebm-papst.com.auwww.ebm-papst.com.au
New Zealandebm-papst Australia Pty Ltd.102 Henderson Valley RoadNZ-Henderson, Auckland 1230Phone +64 / 9 / 837 18 84Fax +64 / 9 / 837 18 99sales@ebm-papst.com.auwww.ebm-papst.com.au
D3G_englisch:Axial_D 30.04.2008 10:59 Seite 51
37799-7-8811 · RA-04/08-3’
ebm-papst
Mulfingen GmbH & Co. KG
Bachmühle 2
D-74673 Mulfingen
Phone +49 (0) 79 38 / 81-0
Fax +49 (0) 79 38 / 81-110
info1@de.ebmpapst.com
www.ebmpapst.com
D3G_englisch:Axial_D 30.04.2008 10:59 Seite 52