Post on 25-Feb-2016
description
CREATING A DRAGSTER BLOCK ON
AUTODESK INVENTOR
Fall 2013
Jonas E. Salk Middle SchoolTechnology Education
PLTWPROJECT LEAD THE WAY
1. Open the ‘Inventor’ program and select ‘NEW’2. Click on the ‘+’ sign next to the ‘Templates’ folder (See arrow - Figure 1) 3. Select ‘Metric’4. Select the ‘Standard (mm).ipt from the ‘Parts’ category5. Select the ‘Create’ button
Dragster Block Construction - InstructionsPage 1
Fall 2013
Figure 1
1. Select ‘Create 2D Sketch (small arrow – Figure 2)2. Select the YZ Plane (large arrow - Figure 2)
Dragster Block Construction - InstructionsPage 2
Fall 2013
Figure 2
1. To make the Y axis vertical, rotate the ‘Right’ view of the ‘View Cube’ by using the view cube rotation arrow (Figure 3A)
2. Ensure that the ‘Y’ axis points up when viewing the axis indicator (Figure 3B)
Dragster Block Construction - InstructionsPage 3
Fall 2013
Figure 3A
Figure 3B
1. Using either the rectangle tool or the line tool, create a rectanglewith the following dimensions:
Length = 305 mmHeight = 70 mm
(See Figure 4)
Dragster Block Construction - InstructionsPage 4
Fall 2013
Figure 4
1. Select ‘Finish Sketch’ (sketch will rotate to a diagonal position)2. Select the ‘Extrude’ icon, and extrude the block 42 mm3. Insure that the ‘Direction 2’ button is selected – see arrow in Figure 54. Select OK.
Dragster Block Construction - InstructionsPage 5
Fall 2013
Figure 5
1. Hover your cursor over the ‘View Cube,’ and a house symbol will appear (see arrow – Figure 6) 2. Right click the Home icon (house symbol) and select ‘Select Current View as Home’ – ‘Fit to View’3. Left click to select
Dragster Block Construction - InstructionsPage 6
Fall 2013
Figure 6
1. In the ‘Browser Window’ double click the Sketch icon (if the Sketch icon is not visible, click the‘+’ sign next to the ‘Extrude’ icon). Drawing will revert to the ‘Sketch’ mode.Note: If the sketch icon is grey (and not active), right click on the word ‘Sketch’ and check off the
‘Visibility’ function. This will make the ‘Sketch’ icon active. 2. If necessary, select the rotation arrow on the view cube to correct drawing orientation 3. Selecting the ‘Line Tool,’ make a diagonal line as shown in Figure 74. Dimension the left end of this line 19 mm from the bottom line of the block (see arrows - Figure 7)
Dragster Block Construction - InstructionsPage 7
Fall 2013
Figure 7
1. Select ‘Finish Sketch.’ Drawing should revert back to the 3D view.2. In the Browser window, right click the word (not icon) ‘Sketch’ and select ‘Visibility’
(the right view will display dimensions)3. Click the ‘Extrude’ tool and select the ‘Cut’ and ‘Direction 2’ icons (see arrows – Figure 8)4. Select the upper face of block (as shown) and select ‘OK
Dragster Block Construction - InstructionsPage 8
Fall 2013
Figure 8
1. In the ‘Browser Window’ right click the ‘Sketch’ word (not icon) and un-check ‘Visibility’2. Block should look like Figure 9 3. On the ‘View Cube’ select the ‘Right’ view. Using the direction arrows, select the ‘Back’ view4. Select ‘Create 2D Sketch,’ and select the back face of block
Dragster Block Construction - InstructionsPage 9
Fall 2013
Figure 9
1. Select the ‘Point’ tool and place a point in the center of the block (when in center, a black dotted horizontal line and black dotted vertical line will appear)
2. Select ‘Finish Sketch.’ Select the ‘Home’ icon from the view cube3. Using the ‘Free Rotate’ button on the Navigation Bar, position the block as shown in Figure 10
Dragster Block Construction - InstructionsPage 10
Fall 2013
Figure 10
1. Select the ‘Hole’ tool and insure that the ‘Termination’ option is set to ‘Distance’2. Put in the following dimensions:
Diameter = 19 mmDepth = 51 mm
2. Also select the Drilled, Flat, and Simple Hole icons (See arrows)3. Select OK
Dragster Block Construction - InstructionsPage 11
Fall 2013
Figure 11
Dragster Block Construction - InstructionsPage 12
Fall 2013
CONGRATULATIONS!
Your block is now completed!