Class F3P Indoor Aerobatic Power Model aIRCRafts

Schedule F3P – AF-15

Security line

Take-off procedure

( not judged, not scored )

F3P-AF-15.01: Knife Edge Golf Ball with 3/4 roll up, half roll integrated, 1/4 roll down

F3P-AF-15.01.01

¾ roll¼ roll

½ roll integrated

F3P-AF-15.01: Knife Edge Golf Ball with 3/4 roll up, half roll integrated, 1/4 roll down

F3P-AF-15.01.01

¾ roll¼ roll

½ roll integrated ½ roll is integrated on

circular flightpath of the ¾ loop.

¾ roll and ¼ roll on middle of the lines.

All radii are equal.

During the knife edge flight the wing must be in the vertical plane.

45°

F3P-AF-15.02: Vertical Eight

F3P-AF-15.02.01

F3P-AF-15.02: Vertical Eight

F3P-AF-15.02.02

All radii are equal.

F3P-AF-15.03: Knife Edge Flight Combination with 1/4 roll, roll, 1/4 roll

F3P-AF-15.03.01

Part rolls must have the same roll rate.

Between rolls and part rolls in opposite direction there must be no line.

F3P-AF-15.04: Figure 6 with stall turn, 1/2 roll down

F3P-AF-15.04.01

Pivot on CG

Stop before pivot

½ roll

F3P-AF-15.04: Figure 6 with stall turn, 1/2 roll down

F3P-AF-15.04.02

Pivot on CG

½ roll

F3P-AF-15.04: Figure 6 with stall turn, 1/2 roll down

F3P-AF-15.04.03

Pivot on CG

½ roll

Two wing spans or more – zero points!

½ roll on middle of the line.

All radii are equal.

F3P-AF-15.05: Cubic Top–Hat with 3/4 roll up, 1/4 roll down, 1/2 roll, 3/4 roll up, 1/4 roll down

F3P-AF-15.05.01

¾ torque roll

¼ roll

½ roll

¾ torque roll¼ roll

F3P-AF-15.05: Cubic Top–Hat with 3/4 roll up, 1/4 roll down, 1/2 roll, 3/4 roll up, 1/4 roll down

F3P-AF-15.05.02

¾ torque roll

¼ roll

½ roll

¾ torque roll¼ roll

All radii are equal.

¾ torque rolls, ¼ rolls and ½ roll on middle of the lines.

F3P-AF-15.06: Half Horizontal Square Circle on Corner with ¼ roll, ½ roll, ½ roll, ¼, roll

F3P-AF-15.06.01

¼ roll

¼ roll

½ roll

½ roll

F3P-AF-15.06: Half Horizontal Square Circle on Corner with ¼ roll, ½ roll, ½ roll, ¼, roll

F3P-AF-15.06.02

¼ roll

¼ roll

½ roll

½ roll

All radii are equal.

½ rolls on middle of the line.

During the knife edge flight the wing must be in the vertical plane.

F3P-AF-15.06: Half Horizontal Square Circle on Corner with ¼ roll, ½ roll, ½ roll, ¼, roll

F3P-AF-15.06.03

¼ roll

¼ roll

½ roll

½ rollOption

¾ rollintegrated

F3P-AF-15.07: Eye-Catcher with two 3/4 rolls integrated in opposite directions

F3P-AF-15.07.01

¾ rollintegrated

¾ rollintegrated

F3P-AF-15.07: Eye-Catcher with two 3/4 rolls integrated in opposite directions

F3P-AF-15.07.02

¾ rollintegrated

Al radii are equal.

Rolls must be in opposite directions.

¾ rolls must be integrated on circular flight path of the ¾ loops.

Roll reversal is immediate.

F3P-AF-15.08.1

F3P-AF-15.08: Half Horizontal Hour Glass with ½ roll down, roll up ½ roll down

½ roll

½ rollroll

F3P-AF-15.08.2

F3P-AF-15.08: Half Horizontal Hour Glass with ½ roll down, roll up ½ roll down

½ roll

½ rollroll

All radii are equal.

45°

½ rolls and roll on middle of the lines.

F3P-AF-15.09.01

F3P-AF-15.09: Horizontal Triangular Circle with 1/4 roll, 1/2 roll integrated, roll, 1/2 roll integrated, roll, 1/2 roll integrated, 1/4 roll

¼ roll

½ roll outside integrated

½ roll outside integrated

roll inside

roll inside

F3P-AF-15.09.02

F3P-AF-15.09: Horizontal Triangular Circle with 1/4 roll, 1/2 roll integrated, roll, 1/2 roll integrated, roll, 1/2 roll integrated, 1/4 roll

¼ roll

½ roll outside integrated

½ roll outside integrated

roll inside

roll inside

F3P-AF-15.09.03

F3P-AF-15.09: Horizontal Triangular Circle with 1/4 roll, 1/2 roll integrated, roll, 1/2 roll integrated, roll, 1/2 roll integrated, 1/4 roll

All ½ rolls are outside and integrated on the flightpath in the corners.

During the knife-edge the wing must be in the vertical plane.

All sides are of equal length, all angles are 60°.

All full rolls are inside and on middle of the lines.

All radii are equal.

F3P-AF-15.10.01

F3P-AF-15.10: Tail Slide with two consecutive 1/8 rolls up

1/8 roll

1/8 roll

F3P-AF-15.10.02

F3P-AF-15.10: Tail Slide with two consecutive 1/8 rolls up

Stick back tail slide.

F3P-AF-15.10.03

F3P-AF-15.10: Tail Slide with two consecutive 1/8 rolls up

1/8 roll 1/8 roll

1/8 rolls centered on middle of the line.

All radii are equal.

Between part rolls in opposite direction there must be no line.

Flipover = 0 points.

F3P-AF-15.11.01

F3P-AF-15.11: Roll Combination with 1 3/4 roll, 1 3/4 roll in opposite direction

Between rolls and in opposite direction there must be no line.

1 ¾ roll

1 ¾ roll

Landing sequence( not judged, not scored )

Peter Uhlig, November 2013

security line