Post on 06-Feb-2018
© NMISA 2012
Calibration of Gauge
Blocks using a
Mechanical Comparator
Name: Refiloe Moganedi
Date: 4th September 2012
© NMISA 2012
Overview
1. Introduction2. Uses of gauge blocks 3. Gauge blocks traceability chain 4. Calibration of gauge blocks using a mechanical
comparator 5. Thermal Expansion6. Elastic Properties7. Conclusion
© NMISA 2010© NMISA 2012
Definition of a gauge block
� A gauge block (also known as a gage block , Johansson gauge , slip gauge , or Jo block ) is a precision ground and lapped length block used as a measuring standard.
� Invented in 1896 by Swedish machinist Carl EdvardJohansson,[1]
� used as a reference for the calibration of measuring equipment used in machine shops, such as micrometers, sine bars, calipers, and dial indicators (when used in an inspection role).
� A gauge block is a block of metal or ceramic with two opposing faces ground precisely flat and parallel, a precise distance apart.
� Gauge blocks made in several grades or degrees of accuracy.
© NMISA 2010© NMISA 2012
Examples of gauge blocks
Measuring faces
Measuring faces
© NMISA 2010© NMISA 2012
Uses of gauge blocks, calibration of callipers
� Kinds of callipers
� They can have an inside, outside, depth and step measurement capabilities� They can be digital, analogue with vernier scale or analogue with dial� They are in Imperial, SI or combination� They can be bench or handheld instruments � Measuring range or� Resolution type of jaws etc.
© NMISA 2010© NMISA 2012
What is calibration?
� To determine the deviation of the measurement indication of an instrument against the true value.
� Gauge blocks are much more accurate than micrometers and verniers
� They serve as calibration standards for micrometers and vernier callipers.
© NMISA 2010© NMISA 2012
Properties of gauge blocks
Gauge block material Advantages Disadvantage
Ceramic Very hard Not easily scratchableHardly breakableMaintenance freeCorrosion resistant
CTE not too close to manufactured (steel) partsExpensiveDifficult to wring
SteelCTE very similar to manufactured (steel) parts.•Less expensive(most economical mechanical and properties are adequate in typical workshop environment)
Not too hard Easy to scratchNeed maintenanceCorrodes easily
© NMISA 2010© NMISA 2012
Properties of gauge blocks
Gauge block material Advantages Disadvantage
Tungsten CarbideVery hard Difficult to scratch Hardly breakableCorrosion resistantExcellent wringing capabilityMaintenance free
CTE not close to manufactured (steel) partsVery low expansion coefficient (1/3 of steel) and because of the high density the blocks are deceptively Heavy
Chromium Carbide
Extremely hard Difficult to scratch Hardly breakableCorrosion resistantExcellent wringing capabilityMaintenance free
CTE not close to manufactured (steel) partsExpensive
© NMISA 2010© NMISA 2012
Gauge block gradesAccording to ISO 3650 (specification for gauge bloc ks)
� Grade 00, 0 and K are calibrated using the interferometer.
� Grade 00, 0 and K should be used as the master set or for verification purposes.
� Grade 1 and 2 are calibrated using the mechanical comparator.
� Grade 1 and 2 are used for checking micrometer and vernier caliper measurements.
© NMISA 2010© NMISA 2012
Gauge block traceability chain (1.2)
© NMISA 2010© NMISA 2012
ISO 3650GPS – Length standards - Gauge blocks
“The length of a gauge block is defined as the perpendicular distance from any particular point on the gauge block and a plane surface of an auxiliary plate of the same material and surface texture upon which the measuring face has been wrung.” With a special note: “This length of the gauge block, l, includes the effect of one-face wringing”
© NMISA 2010© NMISA 2012
Calibration of gauge blocks using a mechanical comparator
© NMISA 2010© NMISA 2012
Pictorial view of a mechanical comparator (1.3)
© NMISA 2010© NMISA 2012
Calibration Method
� Equipment required� Pre- and post-handling of gauge blocks.� Measuring face flatness� Verify if mechanical comparator is in calibrated state.� Calibrating gauge blocks of the same material. Can
gauge blocks of dissimilar materials be calibrated?� Stabilise gauge blocks to equalise temperature between
gauge blocks.� Any compensations made
© NMISA 2010© NMISA 2012
Equipment required
� A GB comparator� A set of Master GBs (Grades 00, 0 or K)� Monochromatic sodium lamp and an Optical flat (not
compulsory)� Thermometer (calibrated) with resolution of 0,1 °C� Magnetic field indicator and demagnetizer (not
compulsory)
© NMISA 2010© NMISA 2012
Accessories needed for the care of gauge blocks
1. Vaseline2. Paraffin3. Ethyl acetate4. Soft tissues5. Lint free cloth6. Substrate no. 1 7. Glove8. Plastic gloves9. Beaker10. Gauge block holder (sucker)
© NMISA 2010© NMISA 2012
The care of gauge blocks (Pre and post handling)
© NMISA 2010© NMISA 2012
Before length measuring
� Clean both sets of GBs, master and UUT.� Check magnetisation and demagnetise if needed.� Leave gauge blocks to stabilise for a period of 25
minutes per 20 mm gauge block.
� Measure face flatness
� Before measurement of each UUT GB, inspect the state of the measuring faces with a magnifying glass for burrs or scratches and check the flatness using the optical flat.
© NMISA 2010© NMISA 2012
Measuring face flatness
Before measurement of each UUT GB, inspect the state of the measuring faces with a magnifying glass for burrs or scratches and check the flatness using the optical flat.
© NMISA 2010© NMISA 2012
Pair No. Nominal lengthA
(mm)
Nominal lengthB
(mm)1 0,5 0,5
2 1,0 1,005
3 1,0 1,01
4 4,0 4,0
5 100,0 100,0
6 6,0 6,0*
Calibration of mechanical comparator according the EAL-G21. Ceramic gauge blocks were used (1.4)
© NMISA 2010© NMISA 2012
Std GB used(mm)
Reading on Std GB
(µm)
Reading on UUT GB
(µm)
Average reading of
UUT(µm)
Corrected Size of UUT(mm)
15 -0,04 -0,05
-0,01 -0,05 -5x10-8 X 1000
0,00 -0,04 -0.00005
-0,02 -0,05 -0,05
15,00010 –0,00005
=15,00005
Table 1: Verification of the same materials -Ceramic vs Ceramic
© NMISA 2010© NMISA 2012
Table 2: Verification of dissimilar materials - Ceramic vs Steel
Std GB used(mm)
Std GB used(mm)
Reading on Std GB
(µm)
Reading on UUT GB
(µm)
Average reading of
UUT(µm)
Corrected Size of UUT(mm)
20 0,00 0,13
0,03 0,03 6x10-8 X 1000
-0,08 0,01 0.00006
-0,02 0,06 0,0620,00001 + 0,00006 = 20,00007
© NMISA 2010© NMISA 2012
Table 3: Verification of dissimilar materials - Steel vs Tungsten Carbide
Std GB used(mm)
Reading on Std GB
(µm)
Reading on UUT GB
(µm)
Average reading of
UUT(µm)
Corrected Size of UUT(mm)
10 0,05 -0.05
0,08 -0,05 -6 x10-8 x 1000
0,09 -0.07 -0.00006
0,08 -0,06 -0.06
0.10 -0.08 9,99997 –0,00006 = 9,99991
© NMISA 2010© NMISA 2012
Same material vs. dissimilar materials
Ceramic vs Ceramic
Steel vs Steel
Tungsten Carbide
vs Tungsten Carbide
Ceramic vs Steel
Tungsten Carbide
vs ceramic
Steel vs Tungsten Carbide
?
© NMISA 2010© NMISA 2012
Thermal Expansion
In most materials, a change in temperature causes a change in dimensions. This change depends on both the size of the temperature change at which the change occurs.
Formulae used for temperature calculations on gauge blocks:
∆L/L = αL ∆TWhere
L = is the length∆L = is the change in lengthα = is the coefficient of thermal expansion (CTE)
∆T = change in temperature
© NMISA 2010© NMISA 2012
Coefficient of thermal expansionMaterial Material Thermal Expansion
Coefficient(10-6/ºC)
Aluminium 24
Free Cutting Brass 20,5
Steel Gauge Block 11,5
Steel Gauge Block ( 500 mm ) 10,6
Ceramic Gauge Block (zirconia) 9,2
Chrome Carbide 8,4
Granite 6,3
Oak (across grain) 5,4
Oak (along grain) 4,9
Tungsten Carbide 4,5
Invar 1,2
Fused Silica 0,55
Zerodur 0,05
© NMISA 2010© NMISA 2012
Example:
The steel gauge block can be used to gauge any material if corrections are made for the differential thermal expansion of the two materials involved. If a steel gauge block is used to gauge a 100 mm aluminium part at 25 ºC, a correction factor must be used. Since the expansion coefficient of aluminium is about twice that of steel, when the part is brought to 20 ºC it will shrink twice as much as the steel. Thus the aluminium block must be made oversized by the amount.
∆L = (αAluminium - αSteel) x L x ∆T = (24 – 11,5) x 10-6 x 100 mm x 5ºC= 6,25 µm
Measurements not made at exactly 20°C needs thermal expansion correction using CTE.
© NMISA 2010© NMISA 2012
Elastic Properties
� When a force is exerted on any material, the material deforms. � For steel and other gauge block materials this effect is small, but not
completely negligible. � There are two-dimensional effects due to the elastic properties of gauge
blocks. The first, and least important, is the compression of blocks under their own weight.
� When a block is supported horizontally, the force on each point is the weight of the steel above it, and the steel is slightly compressed.
� The compression is, however, not in the direction of the gauging dimension of the block and the effect is negligible.
� If the block is set upright, the force is now in the direction of the gauging surfaces, and for very long blocks the weight of the block can become significant.
© NMISA 2010© NMISA 2012
Gravitational sag
∆L = ρgL2/2EWhere
∆L = length of shorteningρ = density of materialg = acceleration of gravityL = total length of blockE = Young's modulus for material
© NMISA 2010© NMISA 2012
Conclusions
� All Gauge blocks of the same material e.g. steel vs steel can be calibrated using the mechanical comparator.
� Any ceramic vs steel gauge block could directly be measured using the mechanical comparator.
� Ceramic blocks have favourable mechanical and thermal properties. It also compares the closest to steel of any alternative gauge block material.
� Steel/ceramic vs tungsten carbide gauge blocks could be measured using the mechanical comparator but temperature and elastic compression corrections have to be made.
© NMISA 2010© NMISA 2012
References
� Definition of calibration: According to BIPM (1.1)� Traceability chain of gauge blocks (1.2) – From Dr. Miguel Viliesid
(Mexico)� Pictorial view of a electromechanical comparator (1.3) Dr. Miguel
Viliesid (Mexico)� Verification of mechanical comparator’s calibration state: From the
EAL-G21 (1.4)� Table of all the thermal Expansion Coefficient (1.5) - The Gauge
Block Handbook� By Ted Doiron and John Beers Dimensional Metrology Group
Precision Engineering Division National Institute of Standards and Technology
� Verify if mechanical comparator is in calibrated state using the EAL-G21
© NMISA 2010© NMISA 2012
Thank you for your attention.