Brush Holders

Schunk Graphite Technology

Table of Contents

2

8 – 10 Clamping Brush Holders

11 – 20 Box Brush Holders

21 – 25 Tandem Brush Holders

26 – 28 Top & Rocker Rings

29 – 35 Appendix

3 – 7 Leg Brush Holders

Brush - dimensions Holder - dimensions

Brush-Article no. t a r d ** q u M pressure *

06.09.2009.10 6.4 6.4 12.5 10 9.5 44 4 18006.09.2106.07 8 5 12.5 7 8 30 3 50006.09.2108.08 10 5 12.5 8 8 35 3 18006.09.2010.10 12.5 6.3 20 10 9.5 40 4 25006.09.2055.13 16 8 16 13 12 50 4 25006.09.2059.13 16 8 16 13 12 62 4 18006.09.0485... 16 8 20 6-13 12 46 6 20006.09.0486... 16 8 20 6-16 12 60 6 20006.09.0622... 16 8 20 6-13 12 50 6 20006.09.2088.10 20 8 20 10 12 50 6 20006.09.2088.60 20 8 20 13 12 50 5 20006.09.0488... 20 8 25 6-16 12 60 6 20006.09.0489... 20 8 25 6-16 12 70 6 20006.09.0638... 20 8 25 6-13 12 50 6 20006.09.0490... 20 10 25 6-16 14.5 60 6 20006.09.0491... 20 10 25 6-16 14.5 70 6 20006.09.0492... 20 10 25 6-16 14.5 80 6 20006.09.0496... 25 10 25 6-16 14.5 55 6 20006.09.0497... 25 10 25 6-16 14.5 65 6 20006.09.2103... 25 10 25 6-16 14.5 80 6 20006.09.0499... 25 12.5 25 6-16 18 75 6 200

Dimensions in mmd ** grooved version available ( Ø 7 - Ø 20)* cN/cm2 - Specific brush pressureFurther dimensions on request

Design subject to change

One-piece clamp

3

Single Leg Brush Holders

4

Single Leg Brush Holders

Brush - dimensions Holder - dimensions

Brush- AdditionalArticle no. t a r d ** q u M pressure * connector

06.09.0500... 20 10 25 16-20 14.5 70 6 20006.09.0501... 20 10 25 16-20 14.5 80 6 20006.09.0502... 25 10 25 16-20 14.5 75 6 20006.09.0503... 25 10 25 16-20 14.5 85 6 20006.09.0504... 25 12.5 25 16-20 18 75 8 20006.09.0505... 25 12.5 25 16-20 18 85 8 20006.09.0506... 32 12.5 32 16-20 18 80 8 20006.09.0509... 32 16 32 16-20 21 90 8 20006.09.0510... 32 16 32 16-20 21 100 8 20006.09.0666.25 32 16 32 25 24 110 8 22506.09.0681.20 32 16 32 20 21 80 8 20006.09.0514... 40 16 40 16-20 21 90 8 20006.09.0515... 40 16 40 16-20 21 120 8 20006.09.0516.25 40 20 40 25 26 115 10 20006.09.0517.25 40 20 40 25 26 125 10 20006.09.0640.25 40 20 40 25 26 108 10 20006.09.0680.25 40 20 40 25 26 108 10 20006.09.2086.25 50 25 40 25 33 135 10 18006.09.2097.13 20 8 20 13 12 100 6 200 x06.09.2101.16 25 10 25 16 14 80 6 200 x06.09.0028... 25 12 25 12-22 19 94 6 225 x06.09.0571.16 25 12.5 25 16 18 70 5 200 x06.09.2048.16 25 16 32 16 24 85 6 200 x06.09.2100.20 32 12.5 32 20 17.5 100 8 200 x06.09.0036... 32 16 32 13-25 24 110 8 225 x06.09.2049.20 32 16 40 20 24 110 8 250 x06.09.0038... 40 16 40 13-25 24 106 8 225 x06.09.0045... 40 20 40 13-25 28 110 8 225 x06.09.0046... 40 20 40 13-25 28 125 8 225 x06.09.0047... 40 20 40 13-25 28 150 8 225 x06.09.0110... 40 20 40 13-25 28 110 8 225 x06.09.0589... 40 20 40 13-25 28 110 8 225 x06.09.2050.25 40 20 40 25 28 110 8 300 x06.09.2052.25 40 20 40 25 28 150 8 200 x06.09.0051... 40 25 40 13-25 33 165 8 225 x06.09.0695.25 50 25 40 25 33 145 8 200 x06.09.2068.25 50 25 40 25 33 145 8 200 x

Dimensions in mmd ** grooved version available ( Ø 7 - Ø 20)* cN/cm2 - Specific brush pressureFurther dimensions on request

Design subject to change

With hinge clamp Hinge clamp with additional connector

Brush - dimensions Holder - dimensions Form design

Brush- WithArticle no. t a r d ** q u M pressure * brush A B C

06.09.4004.08 8 5 16 8 9 35 4 400 x06.09.4004.10 8 5 16 10 9 35 4 180 x06.09.4006... 10 5 12.5 8/10 9 35 4 300 x06.09.4006.09 10 5 12.5 9 9 35 3 400 x06.09.0435.12 10 5 15 12 9 40 4 250 x06.09.4135.09 10 6.4 16 9 10 43 5 550 x x06.09.4099.13 12.5 6.4 20 13 10 47 5 250 x x06.09.4019... 12.5 8 16 10-13 12 40 6 180 x06.09.4384.10 15 6 20 10 10 42 4 800 x x06.09.4383.10 16 6.4 16 10 10 42 4 180 x06.09.4023.10 16 8 20 10 12 45 6 200 x06.09.4028.16 16 8 20 16 12 55 6 200 x06.09.4111.50 16 8 20 12.5 12 46 6 300 x x06.09.4349.13 16 8 20 13 12 46 6 200 x06.09.4392.13 16 8 20 13 12 50 5 200 x06.09.4404.13 16 8 20 13 12 55 6 800 x06.09.4155.13 16 8 20 13 12 50 6 350 x06.09.4160.13 16 8 20 13 12 64 6 275 x x06.09.4160.16 16 8 20 16 12 64 6 275 x06.09.4339.13 16 10 25 13 14 65 6 250 x x06.09.4388.13 20 8 20 13 12 50 6 200 x06.09.4161... 20 8 25 8-13 12 50 6 200 x06.09.4352... 20 10 20 13-16 14 75 6 180 x06.09.4115.13 20 10 25 13 14 70 8 250 x x06.09.4189.13 20 12.5 25 13 17 65 8 200 x06.09.4167.10 25 8 25 10 12 60 6 200 x06.09.4119.13 25 10 25 13 12 70 8 180 x x06.09.4355.13 25 10 25 13 12 70 8 180 x06.09.4199... 32 12.5 32 16-20 17 80 8 200 x

Dimensions in mmd ** grooved version available ( Ø 7 - Ø 20)* cN/cm2 - Specific brush pressureFurther dimensions on request

Design subject to change

Form A Form B Form C

5

Double Leg Brush Holders

6

Double Leg Brush Holders

Brush - dimensions Holder - dimensions

Brush- One HingeArticle no. t a r d ** q u M pressure * piece clamp

06.09.0346... 12.5 8 20 6-13 12 48 6 250 x06.09.0347... 16 8 20 6-13 12 46 6 200 x06.09.0623... 16 8 20 6-13 12 50 6 200 x06.09.0348... 16 8 20 6-16 12 60 6 200 x06.09.0350... 16 10 25 6-16 14.5 50 6 200 x06.09.0352... 20 8 25 6-13 12 50 6 200 x06.09.0353... 20 8 25 6-16 12 60 6 200 x06.09.0354... 20 8 25 6-16 12 70 6 200 x06.09.0356... 20 10 25 6-16 14.5 60 6 200 x06.09.0357... 20 10 25 6-16 14.5 70 6 200 x06.09.0358... 20 10 25 6-16 14.5 80 6 200 x06.09.0361... 20 12.5 25 6-16 18 60 6 200 x06.09.0362... 20 12.5 25 6-16 18 75 6 200 x06.09.0363... 25 8 25 6-16 12 55 6 200 x06.09.0365... 25 10 25 6-16 14.5 55 6 200 x06.09.0366... 25 10 25 6-16 14.5 65 6 200 x06.09.0368... 25 10 25 6-16 14.5 75 6 200 x06.09.0374... 20 10 25 16-20 14.5 70 6 200 x06.09.0376... 25 10 25 16-20 14.5 75 6 200 x06.09.0377... 25 10 25 16-20 14.5 85 6 200 x06.09.0378... 25 12.5 25 16-20 18 75 8 200 x06.09.0379... 25 12.5 25 16-20 18 85 8 200 x06.09.0380... 25 12.5 25 16-20 18 95 8 200 x06.09.0382... 32 12.5 32 16-20 18 80 8 200 x06.09.0385... 32 16 32 16-20 21 90 8 200 x06.09.0386... 32 16 32 16-20 21 100 8 200 x06.09.0388... 32 16 32 16-20 21 120 8 200 x06.09.0389.25 32 20 32 25 26 110 10 200 x06.09.0641.25 40 20 40 25 26 125 10 200 x

Dimensions in mmd ** grooved version available ( Ø 7 - Ø 20)* cN/cm2 - Specific brush pressureFurther dimensions on request

Design subject to change

One piece clamp Hinge Clamp

7

Double Leg Brush Holders

Brush - dimensions Holder - dimensions Form design

Brush- WithArticle no. t a r d ** q u M pressure * brush A B

06.09.4320.13 16 6.3 12 13 12 46 4 375 x x06.09.0700.10 22 6.4 13.5 10 12.5 46 4 250 x x06.09.0701.08 22 6.4 13.5 8 12.5 46 4 250 x x06.09.4301.16 25 8 20 16 17 60 6 275 x06.09.4321... 25 8 20 13-16 16 60 6 250 x x06.09.4303.16 32 10 20 16 17 64 8 375 x x06.09.4323.20 32 10 20 20 17 64 8 200 x

Dimensions in mm* cN/cm2 - Specific brush pressureFurther dimensions on request

Dimensions in mmd ** grooved version available ( Ø 7 - Ø 20)* cN/cm2 - Specific brush pressure

Design subject to change

Design subject to change

Form A Form B

Phase Version Grounding Version

Double leg brush-holders with carbon hinge

Contact arrangement

Brush - dimensions Holder - dimensions

Brush-Article no. t a r d ** q u M pressure *

06.09.2009.10 6.4 6.4 12.5 10 9.5 44 4 18006.09.2106.07 8 5 12.5 7 8 30 3 500

8

Double Clamping Brush Holders

Brush - dimensions Holder Dimensions

StandardArticle no. *9 t a r c e h l q u v w x z M1 M2 M3

DRDS 06.03.3056... 25 10 32 35.5 20.5 18 20.0 17.5 26 17 8.5 19.5 38 6 6DRDS1 06.03.3100... " " " 35.5 20.5 18 20.0 17.5 26 17 8.5 19.5 38 6 6 8DRDS2 06.03.3130... " " " 35.5 20.5 18 20.0 17.5 26 17 8.5 19.5 38 6 6 8DRDS 06.03.3057... 25 12.5 32 35.5 20.5 18 20.0 17.5 26 17 8.5 19.5 38 6 6DRDS1 06.03.3101... " " " 35.5 20.5 18 20.0 17.5 26 17 8.5 19.5 38 6 6 8DRDS2 06.03.3131... " " " 35.5 20.5 18 20.0 17.5 26 17 8.5 19.5 38 6 6 8DRDS 06.03.3058... 32 12.5 40 43.5 26.0 18 25.5 20.5 29.5 17 12.5 19.5 51 6 6DRDS1 06.03.3102... " " " 43.5 26.0 18 25.5 20.5 29.5 17 12.5 19.5 51 6 6 8DRDS2 06.03.3122... " " " 43.5 26.0 18 25.5 20.5 29.5 17 12.5 19.5 51 6 6 8DRDS 06.03.3065... 32 16 40 43.5 26.0 25 25.5 24.0 32 23 12.5 25 51 8 8DRDS1 06.03.3103... " " " 43.5 26.0 25 25.5 24.0 32 23 12.5 25 51 8 8 10DRDS2 06.03.3123... " " " 43.5 26.0 25 25.5 24.0 32 23 12.5 25 51 8 8 10DRDS 06.03.3066... 32 20 40 43.5 26.0 25 25.5 25.5 32 23 12.5 25 48.3 8 8DRDS1 06.03.3104... " " " 43.5 26.0 25 25.5 25.5 32 23 12.5 25 48.3 8 8 10DRDS2 06.03.3124... " " " 43.5 26.0 25 25.5 25.5 32 23 12.5 25 48.3 8 8 10DRDS 06.03.3069... 40 20 50 43.5 27.5 25 27.0 25.5 38 23 12.5 25 49 8 8DRDS1 06.03.3107... " " " 43.5 27.5 25 27.0 25.5 38 23 12.5 25 49 8 8 10DRDS2 06.03.3127... " " " 43.5 27.5 25 27.0 25.5 38 23 12.5 25 49 8 8 10DRDS 06.03.3070... 40 25 50 43.5 27.5 25 27.0 30.5 38 23 12.5 25 49 8 8DRDS1 06.03.3108... " " " 43.5 27.5 25 27.0 30.5 38 23 12.5 25 49 8 8 10DRDS2 06.03.3128... " " " 43.5 27.5 25 27.0 30.5 38 23 12.5 25 49 8 8 10DRDS 06.03.3071... 40 32 50 43.5 27.5 25 27.0 37.5 38 23 12.5 25 49 8 8DRDS1 06.03.3109... " " " 43.5 27.5 25 27.0 37.5 38 23 12.5 25 49 8 8 10DRDS2 06.03.3129... " " " 43.5 27.5 25 27.0 37.5 38 23 12.5 25 49 8 8 10

Dimensions in mm*d = complete dimension "d" in part number* cN/cm2 - Specific brush pressureFurther dimensions on request

Type DRDS, DRDS1, DRDS2

Design subject to change

DRDS

DRDS1

DRDS2

9

Type DRDF, DRDF1, DRDF2

DRDF

DRDF1

DRDF2

Double Clamping Brush Holders

Brush - dimensions Holder Dimensions

StandardArticle no. *9 t a r c e h l q u v w x z M1 M2 M3

DRDF 06.03.4056... 25 10 32 35.5 20.5 18 20.0 17.5 26 17 8.5 19.5 38 6 6DRDF1 06.03.4100... " " " 35.5 20.5 18 20.0 17.5 26 17 8.5 19.5 38 6 6 8DRDF2 06.03.4130... " " " 35.5 20.5 18 20.0 17.5 26 17 8.5 19.5 38 6 6 8DRDF 06.03.4057... 25 12.5 32 35.5 20.5 18 20.0 17.5 26 17 8.5 19.5 38 6 6DRDF1 06.03.4101... " " " 35.5 20.5 18 20.0 17.5 26 17 8.5 19.5 38 6 6 8DRDF2 06.03.4131... " " " 35.5 20.5 18 20.0 17.5 26 17 8.5 19.5 38 6 6 8DRDF 06.03.4058... 32 12.5 40 43.5 26.0 18 25.5 20.5 29.5 17 12.5 19.5 51 6 6DRDF1 06.03.4102... " " " 43.5 26.0 18 25.5 20.5 29.5 17 12.5 19.5 51 6 6 8DRDF2 06.03.4122... " " " 43.5 26.0 18 25.5 20.5 29.5 17 12.5 19.5 51 6 6 8DRDF 06.03.4065... 32 16 40 43.5 26.0 25 25.5 24.0 32 23 12.5 25 51 8 8DRDF1 06.03.4103... " " " 43.5 26.0 25 25.5 24.0 32 23 12.5 25 51 8 8 10DRDF2 06.03.4123... " " " 43.5 26.0 25 25.5 24.0 32 23 12.5 25 51 8 8 10DRDF 06.03.4066... 32 20 40 43.5 26.0 25 25.5 25.5 32 23 12.5 25 48.3 8 8DRDF1 06.03.4104... " " " 43.5 26.0 25 25.5 25.5 32 23 12.5 25 48.3 8 8 10DRDF2 06.03.4124... " " " 43.5 26.0 25 25.5 25.5 32 23 12.5 25 48.3 8 8 10DRDF 06.03.4069... 40 20 50 43.5 27.5 25 27.0 25.5 38 23 12.5 25 49 8 8DRDF1 06.03.4107... " " " 43.5 27.5 25 27.0 25.5 38 23 12.5 25 49 8 8 10DRDF2 06.03.4127... " " " 43.5 27.5 25 27.0 25.5 38 23 12.5 25 49 8 8 10DRDF 06.03.4070... 40 25 50 43.5 27.5 25 27.0 30.5 38 23 12.5 25 49 8 8DRDF1 06.03.4108... " " " 43.5 27.5 25 27.0 30.5 38 23 12.5 25 49 8 8 10DRDF2 06.03.4128... " " " 43.5 27.5 25 27.0 30.5 38 23 12.5 25 49 8 8 10DRDF 06.03.4071... 40 32 50 43.5 27.5 25 27.0 37.5 38 23 12.5 25 49 8 8DRDF1 06.03.4109... " " " 43.5 27.5 25 27.0 37.5 38 23 12.5 25 49 8 8 10DRDF2 06.03.4129... " " " 43.5 27.5 25 27.0 37.5 38 23 12.5 25 49 8 8 10

Dimensions in mm*d = complete dimension "d" in part number* cN/cm2 - Specific brush pressureFurther dimensions on request

Design subject to change

10

Double Clamping Brush Holders

Slip Ring Diameter

Brush Holder 90 100 125 160 200 250 315 400 500DRDF 2510 35 34 33 32.5 32 31.5 31.5 31DRDS 2512 35 34 33 32.5 32 31.5 31.5 31

3212 40 39 38 37.5 36.5 36 36 35.53216 44.5 43.5 43 42 41.5 41 40.53220 44.5 43.5 43 42 41.5 41 40.53225 44.5 43.5 43 42 41.5 41 40.54020 49 48 47 46.5 45.5 454025 49 48 47 46.5 45.5 454032 49 48 47 46.5 45.5 45

DRDF1 2510 35 34 33 32.5 32 31.5 31.5 31DRDF2 2512 35 34 33 32.5 32 31.5 31.5 31DRDS1 3212 40 39 38 37.5 36.5 36 36 35.5DRDS2 3216 44.5 43.5 43 42 41.5 41 40.5

3220 44.5 43.5 43 42 41.5 41 40.53225 44.5 43.5 43 42 41.5 41 40.54020 45.5 44.5 43.5 42.5 42 41.54025 45.5 44.5 43.5 42.5 42 41.54032 45.5 44.5 43.5 42.5 42 41.5

Dimensions in mmDimensions rounded in 0.5 mm incrementsFurther dimensions on request

Slip Ring Measurements

Design subject to change

11

Single Brush Holders

Type BRD

Made of die cast brass with extension spring and spark protection

Brush - dimensions Holder - dimensions Pressure

Type Article no. t a r u c e k m q v z pBRD - 1025 06.04.2108.02 10 25 40 15 37 25 6.4 10.2 29 5.5 58 200BRD - 1225 06.04.2109.01 12.5 25 40 16.3 38 25 6.4 10.2 29 5.5 59 200BRD - 1625 06.04.2110.00 16 25 40 18 40 25 6.4 10.2 29 5.5 61 200BRD - 2025 06.04.2116.02 20 25 40 20 42 25 6.4 10.2 29 5.5 63 200BRD - 1032 06.04.2111.01 10 32 40 15.5 37 25 6.4 10.2 36 5.5 58 200BRD - 1232 06.04.2112.00 12.5 32 40 16.8 38 25 6.4 10.2 36 5.5 59 200BRD - 1632 06.04.2113.00 16 32 40 18.5 40 25 6.4 10.2 36 5.5 61 200BRD - 2032 06.04.2114.00 20 32 40 20.5 42 25 6.4 10.2 36 5.5 63 200BRD - 2532 06.04.2115.00 25 32 40 23 44.5 25 6.4 10.2 36 5.5 65.5 200

Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2

Design subject to change

12

Type BRS

Made from sheet brass with extension spring and spark protection

Brush - dimensions Holder - dimensions Pressure

Type Article no. t a r u c e/I k m q v z pBRS - 1025 06.04.2349.00 10 25 40 15 37 25 6.4 10.2 29 4.5 46 200BRS - 1225 06.04.2350.00 12.5 25 40 16.3 38.25 25 6.4 10.2 29 4.5 46 200BRS - 1625 06.04.2351.00 16 25 40 18 40 25 6.4 10.2 29 4.5 46 200BRS - 2025 06.04.2352.00 20 25 40 20 42 25 6.4 10.2 29 4.5 46 200BRS - 1032 06.04.2353.00 10 32 50 15.5 41.5 30 8.4 14.2 36 4.5 51 200BRS - 1232 06.04.2354.00 12.5 32 50 16.8 42.75 30 8.4 14.2 36 4.5 51 200BRS - 1632 06.04.2355.00 16 32 50 18.5 44.5 30 8.4 14.2 36 4.5 52 200BRS - 2032 06.04.2356.00 20 32 50 20.5 46.5 30 8.4 14.2 36 4.5 54 200BRS - 2532 06.04.2357.00 25 32 50 23 49 30 8.4 14.2 36 4.5 56 200

Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2

Design subject to change

Single Brush Holders

13

Type BRM

Made of die cast brass with extension spring and spark protection

Single Brush Holders

Brush - dimensions Holder - dimensions Pressure

Type Article no. t a r u c e g I k m q v pBRM - 1032 06.04.2329.00 10 32 50 15.5 63 64 40 32 8.5 14.5 37 6 200BRM - 1232 06.04.3089.00 12.5 32 50 16.8 63 64 40 32 8.5 14.5 37 6 200BRM - 1632 06.04.2327.02 16 32 50 18.5 64 64 40 32 8.5 14.5 37 6 200BRM - 2032 06.04.3058.00 20 32 50 28 76 88 43 32 8.5 14.5 37 12.5 200BRM - 2032 06.04.2258.00 20 32 50 26 76 88 43 32 8.5 16.5 37 10.5 200BRM - 2032 06.04.2258.22 20 32 50 20.5 76 88 43 32 8.5 14.5 37 6 200BRM - 2532 06.04.2261.00 25 32 50 26 76 88 43 32 8.5 16.5 37 8 200BRM - 2532 06.04.2261.19 25 32 50 23 76 88 43 32 8.5 14.5 37 6 200

Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2

Design subject to change

14

Type BRG + BRH

Made of die cast brass with extension spring

Single Brush Holders

Brush - dimensions Holder - dimensions Pressure

Type Article no. t a r u c e I k m n q v w pBRG1 - 1025 06.04.2175.00 10 25 50 15 59 84 32 6.4 10.2 20 29.5 5 7 180BRG1 - 1225 06.04.2176.00 12.5 25 50 16.3 60 84 32 6.4 10.2 20 29.5 5 7 180BRG1 - 1625 06.04.2177.00 16 25 50 18 62 84 32 6.4 10.2 20 29.5 5 9 180BRG1 - 1232 06.04.2181.00 12.5 32 64 16.8 76 100 40 8.4 14.2 25 37 6 7 180BRG1 - 1632 06.04.2182.04 16 32 64 18.5 78 100 40 8.4 14.2 25 37 6 9 200BRG1 - 2032 06.04.2184.04 20 32 64 20.5 80 100 40 8.4 14.2 25 37 6 12 200BRG1 - 2532 06.04.2186.00 25 32 64 23 82 100 40 8.4 14.2 25 37 6 12 180BRG1 - 3232 06.04.2188.00 32 32 64 26.5 86 100 40 8.4 14.2 25 37 6 12 180BRG3 - 4032 06.04.2194.00 40 32 64 32 90 100 40 8.4 16.1 25 37 6.5 14 180

Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2

Design subject to change

15

Type ARB1, ARB4, ARB6*

Made from brass sheet with clock spring and spark protection

Single Brush Holders

Spark Protection

Brush - dimensions Holder - dimensions Pressure

Type Article no. t a r u c e I k m q v z pARB1 - 0812 06.04.0028.00 8 12.5 25 14 21 16 20 5.4 9.2 17.5 7 29 180ARB1 - 1012 06.04.0029.00 10 12.5 25 15 22 16 20 5.4 9.2 17.5 7 29 180ARB1 - 0816 06.04.0030.00 8 16 25 14 24 16 20 6.4 10.2 21 7 34 180ARB1 - 1016 06.04.0031.00 10 16 25 15 25 16 20 6.4 10.2 21 7 34 180ARB1 - 1216 06.04.0032.00 12.5 16 25 16.3 26.5 16 20 6.4 10.2 21 7 34 180ARB6 - 0820 06.04.0033.00 8 20 25 14 24 16 20 6.4 10.2 25 7 34 180ARB6 - 1020 06.04.0034.00 10 20 25 15 25 16 20 6.4 10.2 25 7 34 180ARB6 - 1220 06.04.0035.00 12.5 20 25 16.3 26.5 16 20 6.4 10.2 25 7 34 180ARB6 - 1620 06.04.0036.00 16 20 25 18 28 16 20 6.4 10.2 25 7 34 180ARB6 - 1025 06.04.0037.00 10 25 32 15 30.5 20 25 6.4 10.2 30 7 42 180ARB6 - 1225 06.04.0038.00 12.5 25 32 16.3 31.8 20 25 6.4 10.2 30 7 42 180ARB6 - 1625 06.04.0039.00 16 25 32 18 33.5 20 25 6.4 10.2 30 7 42 180ARB6 - 2025 06.04.0040.01 20 25 32 20 35.5 20 25 6.4 10.2 30 7 42 250ARB4 - 1632 06.04.0024.00 16 32 40 18.5 37.5 25 25 8.4 14.2 38 6.5 42 180ARB4 - 2532 06.04.0044.00 25 32 40 23 42 25 25 8.4 14.2 38 6.5 47 180

Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2

ARB1 without spark arrestorARB4 with raised clamping faceARB6 with spark arrestor

*

Design subject to change

Single Brush Holders

Type BRB1

Made of sheet brass with extension spring

16

Brush - dimensions Holder - dimensions Pressure

Type Article no. t a r u c e I k m q v z pBRB1 - 2010 06.04.2296.00 20 10 32 20 33.5 22 20 6.4 10.2 13 5.5 37 200BRB1 - 2512 06.04.2297.00 25 12.5 32 22.5 36 22 22 6.4 10.2 15.5 5.5 38 200BRB1 - 2516 06.04.2298.01 25 16 32 22.5 36 22 22 6.4 10.2 19 5.5 38 200BRB1 - 3216 06.04.2299.00 32 16 40 26.5 42.5 26 26 8.4 14.2 20 5.5 48 200BRB1 - 3220 06.04.2300.00 32 20 40 26.5 42.5 26 26 8.4 14.2 24 5.5 48 200BRB1 - 4020 06.04.2301.00 40 20 40 30.5 46.5 28 28 8.4 14.2 24 5.5 50 200BRB1 - 4025 06.04.2302.00 40 25 40 30.5 46.5 28 28 8.4 14.2 29 5.5 50 200

Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2

Design subject to change

Single Brush Holders

Type CRB

Brass Extrusion with Self Recoiling Spring

17

Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2

Brush - dimensions Holder - dimensions Pressure

Type Article no. t a r u c e I k m q v pCRB - 1025 06.04.4088.01 10 25 50 15 17 63 40 6.4 10.2 29.5 5.5 200CRB - 1225 06.04.4089.01 12.5 25 50 16.3 18.3 63 40 6.4 10.2 29.5 5.5 200CRB - 1625 06.04.4090.02 16 25 50 18 20 67 40 6.4 10.2 29.5 5.5 200CRB - 2025 06.04.4091.02 20 25 50 20 22 70 40 6.4 10.2 29.5 5.5 200CRB - 3030 06.04.4173.00 30 30 64 25.5 27 88 50 6.4 14.2 34.5 6 200CRB - 1032 06.04.4092.02 10 32 64 15.5 17 77 50 6.4 10.2 36.5 6 200CRB - 1232 06.04.4093.02 12.5 32 64 16.8 18.5 77 50 6.4 10.2 36.5 6 200CRB - 1632 06.04.4094.03 16 32 64 18.5 20 81 50 6.4 10.2 36.5 6 200CRB - 2032 06.04.4095.05 20 32 64 20.5 22 84 50 6.4 10.2 36.5 6 200CRB - 2532 06.04.4096.27 25 32 64 23 24.5 88 50 6.4 10.2 36.5 6 200

Design subject to change

Single Brush Holders

Type CRA

Brass Die Casting with Self Recoiling Spring

18

Brush - dimensions Holder - dimensions Pressure

Type Article no. t a r u c e k m I q v pCRA - 0616 06.04.4030.03 6.4 16 40 14 14.5 38 6.4 10.2 26 20 5.5 250CRA - 0818 06.04.4031.03 8 16 40 14 14.5 38 6.4 10.2 26 20 5.5 200CRA - 1016 06.04.4032.11 10 16 40 15 15.5 38 6.4 10.2 26 20 5.5 200CRA - 1216 06.04.4033.01 12.5 16 40 16.3 16.8 38 6.4 10.2 26 20 5.5 200CRA - 0820 06.04.4034.01 8 20 40 14 14.5 38 6.4 10.2 26 24 5.5 200CRA - 1020 06.04.4035.05 10 20 40 15 15.5 38 6.4 10.2 26 24 5.5 200CRA - 1220 06.04.4036.01 12 20 40 16.3 16.8 38 6.4 10.2 26 24 5.5 200CRA - 1620 06.04.4037.01 16 20 40 18 18.5 38 6.4 10.2 26 24 5.5 200CRA - 1225 06.04.4198.02 12.5 25 50 16.25 20.75 50 5.5 10.2 35 29.5 5.5 200CRA - 1625 06.04.4181.01 16 25 50 17.5 22.5 58 6.4 10.2 35 29.5 5.5 160CRA - 1232 06.04.4163.01 12.5 32 64 16.8 23.25 60 8.5 14.2 40 36.5 6 200CRA - 1632 06.04.4164.01 16 32 64 18.5 25 60 8.5 14.2 40 36.5 6 200CRA - 2032 06.04.4165.01 20 32 64 20.5 27 60 8.5 14.2 40 36.5 6 200CRA - 2532 06.04.4166.01 25 32 64 23 29.5 60 8.5 14.2 40 36.5 6 200

Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2

Design subject to change

Double Brush Holders

Type BRE

Made of die cast brass with extension spring and spark protection

19

Brush - dimensions Holder - dimensions Pressure

Type Article no. t a r u c e I q z pBRE - 1012 06.04.2244.00 10 12.5 32 17 38.5 26 22 31.5 43 200BRE - 1612 06.04.2245.00 16 12.5 32 20 41.5 26 22 31.5 45 200BRE - 2012 06.04.2246.00 20 12.5 32 22 43.5 26 22 31.5 45 200BRE - 1216 06.04.2248.00 12.5 16 32 18 45 26 23 38.5 49 200BRE - 1616 06.04.2249.00 16 16 40 20 50 31 25 38.5 55 200BRE - 2016 06.04.2250.00 20 16 40 22 52 31 25 38.5 55 200BRE - 2516 06.04.2251.00 25 16 50 24.5 55 37 30 38.5 59 200BRE - 1620 06.04.2252.00 16 20 40 20 52 31 25 46.5 55 200

Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2

Design subject to change

Triple Brush Holders

Type BRF

Made of Cast Bronze with extension spring and spark protection

20

Brush - dimensions Holder - dimensions Pressure

Type Article no. t a r u c e I q z pBRF - 1012 06.04.2254.00 10 12.5 32 17 38.5 26 22 46 43 200BRF - 1612 06.04.2255.00 16 12.5 32 20 41.5 26 22 49 45 200BRF - 2012 06.04.2256.00 20 12.5 32 22 43.5 26 22 46.5 45 200BRF - 2516 06.04.2257.00 25 16 50 24.5 55 37 30 59 59 200

Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2

Design subject to change

Tandem Brush Holders

Type TRA, TRA2*

Made of brass die casting with extension spring and spark protection

21

Brush - dimensions Holder - dimensions Pressure

Type Article no. t a r u v c e z pTRA2 - 1032 06.07.0098.02 10 32 50 28 10.5 65.7 33 63 200*TRA2 - 1232 06.07.0099.02 12.5 32 50 28 8 70.7 39.7 68 200*TRA2 - 1632 06.07.0100.02 16 32 50 32 8.5 89.2 42.5 86 200TRA - 2032 06.07.0101.00 20 32 50 36 8.5 93.9 40 86 200

Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2

* - please be advised that when the peripheral speed is greater than 40 m/sec, it is recommended that the spring pressure beequal to or greater than 250 cN/cm2

TRA is with cast brush fingersTRA2 is with stamped brush fingers*

Design subject to change

Tandem Brush Holders

Type TRB1, TRB2, TRB3, TRB4*

Made of brass die casting with extension spring and spark protection

22

Brush - dimensions Holder - dimensions Pressure

Type Article no. t a r u v c e z pTRB3 - 0832 06.07.0193.00 8 32 50 28 12 63.5 35 73 350TRB3 - 1032 06.07.0061.03 10 32 50 28 9.5 63.5 35 73 200*TRB3 - 1232 06.07.0062.06 12.5 32 50 28 9.5 63.5 35 75 200*TRB3 - 1632 06.07.0063.05 16 32 50 28 6.5 63.5 35 76 200TRB1 - 2032 06.07.0064.06 20 32 50 28 6.5 63.5 35 80 200TRB4 - 1032 06.07.0049.02 10 32 50 28 9.5 63.5 35 73 250TRB4 - 1232 06.07.0050.03 12.5 32 50 28 9.5 63.5 35 75 250TRB4 - 1632 06.07.0051.02 16 32 50 28 6.5 63.5 35 76 200TRB2 - 2032 06.07.0052.00 20 32 50 32 6.5 63.5 35 80 200

Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2

* - please be advised that when the peripheral speed is greater than 40 m/sec, it is recommended that the spring pressure beequal to or greater than 250 cN/cm2

TRB1 is with die cast pressure fingers and serrated mounting faceTRB2 is with die cast pressure fingers and mounting cavityTRB3 is with stamped pressure fingers and serrated mounting faceTRB4 is with stamped pressure fingers and mounting cavity

*

Design subject to change

Tandem Brush Holders

Type TNA, TNA2* 7.5°

Made of brass die casting with extension spring and spark protection

23

Brush - dimensions Holder - dimensions Pressure

Type Article no. t a r u v c e z pTNA2 - 1032 06.07.0102.03 10 32 50 28 6 60.8 40.7 64 200*TNA2 - 1232 06.07.0103.05 12.5 32 50 28 6 66.2 42 68 200*TNA2 - 1632 06.07.0104.02 16 32 50 32 6 85.5 44.7 86 200TNA - 2032 06.07.0105.00 20 32 50 28 6 87 44.9 87 200

Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2

* - please be advised that when the peripheral speed is greater than 40 m/sec, it is recommended that the spring pressure beequal to or greater than 250 cN/cm2

TNA is with die cast pressure fingers and serrated mounting faceTNA2 is with stamped pressure fingers and serrated mounting face*

Design subject to change

Tandem Brush Holders

Type TNC1, TNC2, TNC3, TNC4* 8°

Made of brass die casting with extension spring and spark protection

24

Brush - dimensions Holder - dimensions Pressure

Type Article no. t a r u v c e z pTNC3 - 1032 06.07.0094.09 10 32 50 27 6.5 60.5 41 63 200*TNC3 - 1232 06.07.0095.12 12.5 32 50 29.5 6.5 65.8 42.7 68 200*TNC3 - 1632 06.07.0096.14 16 32 50 32 6.5 84.7 45.3 86 200TNC1 - 2032 06.07.0097.06 20 32 50 36 6.5 86.7 45.3 86 200TNC1 - 2532 06.07.0194.04 25 32 50 42 6.5 94 42 90 200TNC4 - 1032 06.07.0082.06 10 32 50 27 6.5 60.5 41 63 250TNC4 - 1232 06.07.0083.06 12.5 32 50 29.5 6.5 65.8 42.7 68 250TNC4 - 1632 06.07.0084.06 16 32 50 32.5 6.5 84.7 45.3 86 200TNC2 - 2032 06.07.0085.06 20 32 50 36.5 6.5 86.7 45.3 86 200TNC2 - 2532 06.07.0194.02 25 32 50 42 6.5 94 42 90 200

Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2

* - please be advised that when the peripheral speed is greater than 40 m/sec, it is recommended that the spring pressure beequal to or greater than 250 cN/cm2

TNC1 is with die cast pressure fingers and serrated mounting faceTNC2 is with die cast pressure fingers and mounting cavityTNC3 is with stamped pressure fingers and serrated mounting faceTNC4 is with stamped pressure fingers and mounting cavity

*

Design subject to change

Tandem Brush Holders

Type TRG2, TNH2, TNH4*

Made of brass die casting with self recoiling spring

25

Brush - dimensions Holder - dimensions Pressure

Type Article no. t a r u k b I pTRG2 - 0832 06.07.0191.00 8 32 64 42.7 90 82 11.5 225TRG2 - 1032 06.07.0189.00 10 32 64 42.7 90 82 11.5 225TRG2 - 1232 06.07.0179.01 12 32 64 42.7 90 82 11.5 225TNH2 - 1232 06.07.0113.02 12.5 32 64 42 84 68 11.5 225TNH4 - 1232 06.07.0111.02 12.5 32 64 42 84 68 11.5 225TNH2 - 1632 06.07.0114.01 16 32 64 45 86 74.4 13 200TNH4 - 1632 06.07.0112.02 16 32 64 45 86 74.4 12 200

Dimensions in mmFurther dimensions on requestSerration per DIN 43 040Brush box tolerances DIN 43 000/2 E10p = specific brush pressure in cN/cm2

TRG2 and TNH2 are with serrated mounting faceTNH4 is with mounting cavity*

Design subject to change

26

Top Rings

SMK no. D d Pole Wd TK51.60.0176.04 303 254 4 Loch 11 27451.60.0168.00 305 271 4 Loch 8 28851.60.5100.01 305 241 4 Loch 6 26051.60.5100.02 305 241 4 Loch 6 26051.60.5100.03 305 241 4 Loch 6 28451.60.5100.04 305 241 4 Loch 6 28451.60.5100.05 305 241 4 Loch 6 26051.60.5100.06 305 253 4 Loch 6 26051.60.5100.07 305 253 4 Loch 6 28451.60.5100.08 305 253 4 Loch 6 26051.60.5100.09 305 253 4 Loch 6 28451.60.5101.01 340 276 4 Loch 6 29451.60.5101.02 340 276 4 Loch 6 29451.60.5101.03 340 276 4 Loch 6 32051.60.0176.03 343 294 4 Loch 11 31451.60.0167.00 345 306 4 Loch 8 32651.60.5114.01 350 290 4 Loch 8 31051.60.5114.02 350 290 4 Loch 8 31051.60.0176.05 363 314 4 Loch 11 33551.60.0176.02 400 354 4 Loch 10 37351.60.0176.01 450 404 4 Loch 10 42551.60.0176.00 500 454 6 Loch 10 47051.60.0176.08 370 326 4 Loch 10 345

Design subject to change

27

Rocker Rings

SMK no. Outer Dia. D Inner Dia. d Pole R B b51.60.0178.00 64.5 40 2 6 1051.60.0178.01 64.5 40 2 6 1051.60.5162.00 76 43 2 8 851.60.5027.00 87 48 2 19 11.551.60.0174.00 88 58 4 6 651.60.5028.00 88 52 2 8 16 851.60.5102.00 100 55 2 17 551.60.5108.00 100 62 2 12 2451.60.5080.01 102 45 4 551.60.5104.00 114 72 4 10 30 1051.60.5120.01 135 95 2 10 18 1051.60.5120.02 135 95 2 10 18 1051.60.0151.00 140 100 4 13 39.75 1351.60.5007.00 140 100 4 13 16.5 1351.60.5007.02 140 100 4 13 1351.60.5043.00 140 100 4 13 26.5 1351.60.5044.00 140 100 4 16 16.5 1351.60.0179.00 150 92 2 10 13 751.60.5006.01 160 120 4 12 24 1251.60.5006.04 160 120 4 12 35 1251.60.5006.10 160 120 4 12 31 1251.60.5008.00 160 110 4 16.5 31.5 16.551.60.5022.00 160 140 4 12 26 1251.60.5047.00 160 110 2 14 14 1451.60.5146.00 160 110 4 16 19.5 1651.60.0180.00 165 107 2 10 13 751.60.0183.00 165 107 4 13 37.7 851.60.0184.00 165 92 2 13 40.2 851.60.5049.00 165 105 4 13 30 851.60.0082.00 170 115 2 12 10.5 651.60.5050.01 170 126 4 18 43 851.60.5050.02 170 126 4 18 43 851.60.5041.00 172 125/69 4 24 651.60.5042.00 172 125/84 4 24 651.60.0181.00 175 118 2 15 15 751.60.5023.00 180 140 4 12 16 1251.60.5023.02 180 140 4 12 16 1251.60.5138.00 185 120 4 9 551.60.5138.01 185 120 4 9 551.60.5053.01 190 140 4 16 37 1651.60.5053.02 190 140 4 16 43 1651.60.5016.00 193 145 4 18 47 851.60.5002.00 200 140 4 15 41 1051.60.5021.00 200 160 4 12 25 1251.60.5054.00 200 145 4 16 1651.60.0188.00 202 150 4 18 30 1851.60.5131.00 205 138 4 22 20 1051.60.5131.01 205 138 4 22 47 10

Design subject to change

28

Rocker Rings

51.60.5017.00 223 173 4 16 20 1651.60.5058.00 223 173 4 16 25 1651.60.0173.00 225 164 4 25 48 1051.60.5132.00 225 164 4 27 25 1051.60.5132.01 225 164 4 27 52 1051.60.5019.00 235 175 4 18 61 851.60.5019.02 235 175 4 18 28 851.60.0154.03 240 170 4 17 23 1051.60.0154.02 240.5 170 4 17 23 1051.60.5097.01 250 175.4 4 18 76 1051.60.5105.01 250 174 4 18 50 1051.60.0169.00 255 186 4 18 24 1451.60.0169.01 255 186 4 18 24 1451.60.0185.00 255 186 4 22 24 1451.60.0098.02 260 205 4 20 2051.60.5012.00 260 190 4 25 41.5 751.60.5089.01 270 205 4 20 31 2051.60.0097.01 275 204 21.551.60.0109.01 285 215 4 25 10.551.60.0109.00 287 215 4 24.3 26.6 11.351.60.0186.00 288 200 4 27 29.5 1451.60.5091.01 288 200 4 27 29.5 1451.60.0166.01 295 219 4 17 33.5 1451.60.0166.02 295 219 4 17 33.5 1451.60.5061.00 295 235 4 30 63.5 751.60.5062.00 295 235 4 30 37 751.60.0150.00 315 225 4 25 2051.60.0150.02 315 225 4 25 2051.60.5013.00 320 235 4 30 77 951.60.5014.00 320 235 4 30 50.5 951.60.5095.00 335 235 4 30 32 1451.60.5095.01 335 235 4 30 32 1451.60.0150.01 340 250 4 25 2051.60.0150.03 340 250 4 25 2051.60.5161.00 340 250 4 32 35 1451.60.5092.00 370 270 4 32 35 1451.60.5092.01 370 270 4 32 40 1451.60.5093.00 370 270 4 32 35 1451.60.5093.01 370 270 4 32 35 1451.60.5093.02 370 270 4 32 40 1451.60.5149.00 380 270 4 34 106.5 1051.60.5149.01 380 270 4 34 80.5 1051.60.5149.02 380 270 4 34 79.5 1051.60.5149.03 380 270 4 34 46 1051.60.5150.00 420 310 4 36 120 1051.60.5150.01 420 310 4 36 111.5 1051.60.5150.02 420 310 4 36 85.5 1051.60.5150.03 420 310 4 36 51 1051.60.0170.00 450 330 4 40 42 1451.60.0171.00 570 425 4 / 6 50 52 14

SMK no. Outer Dia. D Inner Dia. d Pole R B b

Design subject to change

29

1 2 3

4 5

6 7

30

8

10

12

14 15

13

11

9

31

16

21

26

31 32 33 34 35

27 28 29 30

22 23 24 25

17 18 19 20

32

36

40

44 45 46 47

41 42 43

37 38 39

33

48

54

60

66

72 73 74 75 76 77

67 68 69 70 71

61 62 63 64 65

55 56 57 59

49 50 51 52 53

34

78

82

85

88 89 90

86 87

83 84

79 80 81

35

Other Special Designs

Plug-inbrushholder

EarthingContacts

Roller-holders

Flange-brush-holder

Schunk Graphite Technology

W146 N9300 Held DriveMenomonee Falls, WI 53051

Phone: 262-253-8720Toll Free: 888-560-7744Fax: 262-644-6073

www.schunkgraphite.com