Post on 28-Mar-2020
This is information on a product in full production.
June 2014 DocID022930 Rev 5 1/27
SPBT2632C1A
Bluetooth® technology class-1 module
Datasheet - production data
Features• Bluetooth radio
– Fully embedded Bluetooth® v3.0 with profiles
– Class 1 module– Complete RF ready module– 128-bit encryption security– Range up to 60 m LOS– Integrated antenna – Multipoint capability
• ST Micro Cortex-M3 microprocessor up to 72 MHz (256kb flash, 48kb RAM memory)
• Modem transmitter speed– With SPP service active: 560kbps
transmission speed
• General I/O– 16 general purpose I/Os
• User interface– AT2 command set (abSerial)– Firmware upgrade over UART
• FCC and Bluetooth® qualified
• Single voltage supply: 2.5 V typical
• Small form factor: 15 x 27 x 2.9 mm
• Operating temperature range: -40 °C to 85 °C
www.st.com
Contents SPBT2632C1A
2/27 DocID022930 Rev 5
Contents
1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2 RoHS compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4 Software architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.1 Lower layer stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.2 Upper layer stack: Amp’ed UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.3 AT command set: abSerial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.4 Bluetooth firmware implantation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5 Hardware specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.1 Recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.2 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.3 High speed mode CPU current consumption . . . . . . . . . . . . . . . . . . . . . . . 8
5.4 Standard CPU mode current consumption . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.5 I/O operating characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.6 Selected RF characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.7 Pin assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.8 Mechanical dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6 Hardware block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7 Hardware design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7.1 Module reflow installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7.2 GPIO interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7.3 GPIO configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7.4 UART interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
7.5 PCB layout guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7.6 Reset circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7.6.1 External reset circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7.6.2 Internal reset circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
DocID022930 Rev 5 3/27
SPBT2632C1A Contents
27
7.7 Apple iOS CP reference design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
8 Regulatory compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8.1 FCC and IC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8.2 Bluetooth certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8.3 CE certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
9 Traceability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
10 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
11 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Description SPBT2632C1A
4/27 DocID022930 Rev 5
1 Description
The SPBT2632C1A.AT2 is an easy to use Bluetooth module, compliant with Bluetooth v3.0.
The module provides complete RF platform in a small form factor.
The SPBT2632C1A.AT2 enables electronic devices with wireless connectivity, not requiring any RF experience or expertise for integration into the final product. The SPBT2632C1A.AT2 module, being a certified solution, optimizes the time to market of the final application.
The module is designed for maximum performance in a minimal space including fast speed UART and 16 general purpose I/O lines, several serial interface options, and up to 560 kbps transmission speed with SPP service active, 250 kbps with iAP service active.
An optimized design allows the integration of a complete working Bluetooth modem, including antenna and LPO (low power oscillator), enabling low power mode capability in the minimum possible size.
The SPBT2632C1A.AT2 is a surface mount PCB module that provides fully embedded, ready-to-use Bluetooth wireless technology. The reprogrammable Flash memory contains embedded firmware for serial cable replacement using the Bluetooth SPP profile.
Embedded Bluetooth AT2 command firmware is a friendly interface, which realizes a simple control for cable replacement, enabling communication with most Bluetooth enabled devices, provided that the devices support SPP profile. The SPBT2532C1A.AT2, supporting iAP profile, provides communication with Android, smartphone and Apple® iOS Bluetooth enabled devices. An Apple authentication IC is required to exchange data with an Apple device or access an Apple device application. The AT2 FW includes the Bluetooth SPP profile capable of recognizing the Apple authentication chip.
Customers using the Apple authentication IC must register as developers, to become an Apple certified MFI member. License fees may apply, for additional information visit: http://developer.apple.com/programs/which-program/index.html.
Certified MFI developers developing electronic accessories that connect to an iPod®, iPhone®, and iPad® can gain access to technical documentation, hardware components, technical support and certification logos.
Customized firmware for peripheral device interaction, power optimization, security, and other proprietary features may be supported and can be ordered pre-loaded and configured.
DocID022930 Rev 5 5/27
SPBT2632C1A RoHS compliance
27
2 RoHS compliance
ST Bluetooth modules comply with the ECOPACK2 level of RoHS compliance. The Material Declaration file is available from the ST website at the following URL: http://www.st.com/web/catalog/sense_power/FM1968/CL1976/SC1324/PF253471#.
3 Applications
• Serial cable replacement
• M2M industrial control
• Service diagnostics
• Data acquisition equipment
• Machine controls
• Sensor monitoring
• Security systems
• Mobile health.
Software architecture SPBT2632C1A
6/27 DocID022930 Rev 5
4 Software architecture
4.1 Lower layer stack • Bluetooth v3.0
• Device power active, sleep and deep sleep
• Wake on Bluetooth feature optimized power consumption of host CPU
• Authentication and encryption
• Encryption key length from 8 bits to 128 bits
• Persistent Flash memory for BD address and radio parameter storage
• All ACL (asynchronous connection less) packet types
• Multipoint capability
• Sniff mode: fully supported to maximum allowed intervals
• Master slave switch supported during connection and post connection
• Dedicated inquiry access code for improved inquiry scan performance
• Dynamic packet selection channel quality driven data rate to optimize link performance
• Dynamic power control
• Bluetooth radio natively supports 802.11b coexistence AFH
4.2 Upper layer stack: Amp’ed UP• SPP, IAP, SDAP and GAP protocols
• RFComm, SDP and L2CAP supported
• Multipoint with simultaneous slaves
4.3 AT command set: abSerial• The complete command list including the iAP commands is reported in user manual
UM1547
DocID022930 Rev 5 7/27
SPBT2632C1A Software architecture
27
4.4 Bluetooth firmware implantation
Figure 1. FW architecture
Hardware specifications SPBT2632C1A
8/27 DocID022930 Rev 5
5 Hardware specifications
General conditions (VIN= 2.5 V and 25 °C).
5.1 Recommended operating conditions
5.2 Absolute maximum ratings
5.3 High speed mode CPU current consumption• High speed CPU mode current consumption
– CPU 32 MHz
– UART supports up to 921 Kbps
– Max data throughput
– Shallow sleep enabled
Table 1. Recommended operating conditions
Rating Min. Typ. Max. Unit
Operating temperature range -40 - 85 °C
Supply voltage VIN 2.0 2.5 3.6 V
Signal pin voltage - 2.1 - V
RF frequency 2400 - 2483.5 MHz
Table 2. Absolute maximum ratings
Rating Min. Typ. Max. Unit
Storage temperature range -55 - +105 °C
Supply voltage, VIN -0.3 - + 5.0 V
I/O pin voltage, VIO -0.3 - + 5.5 V
RF input power - - -5 dBm
Table 3. Current consumption
Modes (typical power consumption) Avg Unit
ACL data 115 K Baud UART at max. throughput (master) 23 mA
ACL data 115 K Baud UART at max. throughput (slave) 27.5 mA
Connection, no data traffic, master 9.1 mA
Connection, no data traffic, slave 11.2 mA
Connection in sniff (Tsniff=375 ms), no data traffic, master 490 µA
DocID022930 Rev 5 9/27
SPBT2632C1A Hardware specifications
27
5.4 Standard CPU mode current consumption• High speed CPU mode
– CPU 8 MHz
– UART supports up to 115 Kbps
– Data throughput up to 200 Kbps
– Shallow sleep enabled
5.5 I/O operating characteristics
Standby, without deep sleep 8.6 mA
Standby, with deep sleep 60 µA
Page/inquiry scan, deep sleep 520 µA
Table 3. Current consumption (continued)
Modes (typical power consumption) Avg Unit
Table 4. Standard CPU mode current consumption
Modes (typical power consumption) Avg. Unit
ACL data 115 K Baud UART at max. throughput (master) 16.7 mA
ACL data 115 K Baud UART at max. throughput (slave) 18 mA
Connection, no data traffic, master 4.9 mA
Connection, no data traffic, slave 7.0 mA
Connection in sniff (Tsniff=375 ms), no data traffic, master 490 µA
Standby, without deep sleep 4.2 mA
Standby, with deep sleep 60 µA
Page/Inquiry scan, deep sleep 520 µA
Table 5. I/O operating characteristics
Symbol Parameter Min. Max. Unit Conditions
VIL Low level input voltage - 0.6 V VIN, 2.1 V
VIH High level input voltage 1.4 - V VIN, 2.1 V
VOL Low level output voltage - 0.4 V VIN, 2.1 V
VOH High level output voltage 1.8 - V VIN, 2.1 V
IOL Low level output current - 4.0 mA VOL = 0.4 V
IOH High level output current - 4.0 mA VOH = 1.8 V
RPU Pull-up resistor 80 120 kW Resistor turned on
RPD Pull-down resistor 80 120 kW Resistor turned on
Hardware specifications SPBT2632C1A
10/27 DocID022930 Rev 5
5.6 Selected RF characteristics
5.7 Pin assignment
Figure 2. Pin connection diagram
Table 6. Selected RF characteristics
Parameters Conditions Typical(1)
1. RF characteristics can be influenced by physical characteristics of final application
Unit
Antenna load 50 ohm
Radio receiver
Sensitivity level BER < .001 with DH5 -90 dBm
Maximum usable level BER < .001 with DH1 0 dBm
Input VSWR 2.5:1
Radio transmitter
Maximum output power 50 W load +10 dBm
Initial carrier frequency tolerance 0 kHz
20 dB bandwidth for modulated carrier 935 kHz
DocID022930 Rev 5 11/27
SPBT2632C1A Hardware specifications
27
Table 7. Pin assignment
Name Type Pin # Description ALT function(1) 5 V tolerant
UART interface
RXD I 8 Receive data Y
TXD O 6 Transmit data Y
CTS I 9 Clear to send (active low) Y
RTS O 10Request to send (active
low)Y
Boot loader
Boot 0 I 2 Reserved
Power and ground
VDD 24 VDD
GND 23 GND
Reset
RESETN I 3Reset input (active low for
5 ms)2.5 Vmax
GPIO - general purpose input/output
GPIO [0] I/O 16General purpose
input/outputY
GPIO [1] I/O 17General purpose
input/outputY
GPIO [2] I/O 19General purpose
input/outputY
GPIO [3] I/O 1General purpose
input/outputY
GPIO [4] I/O 18General purpose
input/outputUART 2 RXD Y
GPIO [5] I/O 20General purpose
input/outputUART 2 TXD Y
GPIO [6] I/O 22General purpose
input/outputADC 0 2.5 Vmax
GPIO [7] I/O 13General purpose
input/outputADC 1 2.5 Vmax
GPIO [8] I/O 4General purpose
input/outputADC 2 2.5 Vmax
GPIO [9] I/O 7General purpose
input/outputADC 3 2.5 Vmax
GPIO [10] I/O 5General purpose
input/outputY
Hardware specifications SPBT2632C1A
12/27 DocID022930 Rev 5
GPIO [11] I/O 11General purpose
input/outputI2C SCL Y
GPIO [12] I/O 12General purpose
input/outputI2C SDA Y
GPIO [13] I/O 15General purpose
input/outputY
GPIO [14] I/O 14General purpose
input/outputY
GPIO [15] I/O 21General purpose
input/outputDAC 2.5 Vmax
1. Please note that the usage of ALT function is dependant upon the firmware that is loaded into the module, and is beyond the scope of this document. The AT command interface uses the main UART by default.
Table 7. Pin assignment (continued)
Name Type Pin # Description ALT function(1) 5 V tolerant
DocID022930 Rev 5 13/27
SPBT2632C1A Hardware specifications
27
5.8 Mechanical dimensions
Figure 3. Mechanical dimensions
Hardware specifications SPBT2632C1A
14/27 DocID022930 Rev 5
Figure 4. Recommend land pattern top view
DocID022930 Rev 5 15/27
SPBT2632C1A Hardware block diagram
27
6 Hardware block diagram
Figure 5. SPBT2632C1A.AT2 module block diagram
Hardware design SPBT2632C1A
16/27 DocID022930 Rev 5
7 Hardware design
The SPBT2632C1A module without AT2 command embedded FW, supports UART, I2C and GPIO hardware interfaces. Note that the use of these interfaces is dependent upon the firmware that is loaded into the module, and is beyond the scope of this document. The AT2 command interface uses the main UART by default.
Note: 1 All unused pins should be left floating; do not ground.
2 All GND pins must be well grounded.
3 The area around the module should be free of any ground planes, power planes, trace routings, or metal for 6 mm from the antenna in all directions.
4 Traces should not be routed underneath the module.
7.1 Module reflow installationThe SPB2632C1A is a high temperature-strength surface-mount Bluetooth module supplied on a 24-pin, 6-layer PCB. The final assembly recommended reflow profiles are indicated below.
The soldering phase must be executed with care. In order to avoid an undesired melting phenomenon, particular attention must be paid to the setup of the peak temperature.
Table 8 contains some suggestions for the temperature profile based on IPC/JEDEC J-STD-020C, July 2004 recommendations.
Table 8. Soldering
Profile feature PB-free assembly
Average ramp-up rate (TSMAX to TP) 3 °C/sec max.
Preheat:– Temperature min. (TS min.)
– Temperature max. (TS max.)– Time (ts min. to ts max.)(ts)
150 °C
200 °C60-100 sec
Time maintained above:– Temperature TL
– Temperature TL
217 °C60-70 sec
Peak temperature (TP) 240 + 0 °C
Time within 5 °C of actual peak temperature (TP) 10-20 sec
Ramp-down rate 6 °C/sec
Time from 25 °C to peak temperature 8 minutes max.
DocID022930 Rev 5 17/27
SPBT2632C1A Hardware design
27
Figure 6. Soldering profile
7.2 GPIO interfaceAll GPIOs are capable of sinking and sourcing 8 mA of I/O current. GPIO [0] to GPIO [7] are internally pulled down with 100 kW (nominal) resistors, GPIO [8] to GPIO [15] are internally pulled up with 100 kW (nominal) resistors.
7.3 GPIO configurationModule GPIO configuration depends on the FW embedded.
For example, the following table summarizes the GPIO configuration set by the standard FW version, the .AT2
GPIO4: active status probe (MCU RUN): always on when the radio is in active mode;
Blinking when the radio is in deep sleep mode
GPIO1: connection status probe: always on when the module is connected
GPIO can be reconfigured using the following commands:
• At+ab gpioconfig [GPIO pin] [I/O]
• At+ab gpioRead [GPIO pin]
• At+ab gpioWrite [GPIO pin] [1/0]
GPIO1 GPIO2 GPIO3 GPIO4 GPIO5-7 GPIO8-16
SPBT2632C1A.AT2
Output/
connection status probe
Input/
pulled-downBOOT
Input/
pulled-down
Output/active status
probe
Input/
pulled-down
Input/
pulled-up
Hardware design SPBT2632C1A
18/27 DocID022930 Rev 5
For additional details, refer to user manual UM1547.
7.4 UART interfaceThe UART is compatible with the 16550 industry standard. Four signals are provided with the UART interface. The TXD and RXD pins are used for data while the CTS and RTS pins are used for flow control.
Figure 7. Connection to host device
Figure 8. Typical RS232 circuit
DocID022930 Rev 5 19/27
SPBT2632C1A Hardware design
27
7.5 PCB layout guidelines
Figure 9. PCB layout guidelines
7.6 Reset circuitTwo types of system reset circuits are detailed below. The maximum voltage that can be supplied to the RESET pin is 2.5 V. As shown in Figure 9 and Figure 10 the RESET is active low, in absence of a reset circuit the pin is internally pulled up and therefore inactive.
7.6.1 External reset circuit
Figure 10. External reset circuit
Hardware design SPBT2632C1A
20/27 DocID022930 Rev 5
Note: RPU ranges from 30 kW to 50 kW internally.
7.6.2 Internal reset circuit
Figure 11. Internal reset circuit
Note: 1 RPU ranges from 30 kW to 50 kW internally.
2 RRST should be from 1 kW to 10 kW.
7.7 Apple iOS CP reference designThe figures below give an indicative overview of what the hardware concept looks like. A specific MFI co-processor layout is available for licensed MFI developers from the MFI program.
Figure 12. BT module
DocID022930 Rev 5 21/27
SPBT2632C1A Hardware design
27
Figure 13. Co-processor
Figure 14. Power switch
C?
100n
R?10k
R?10k
C?100n
R?10kU?
NC5
NC3
RST7
VCC8
VSS1
I2C_SCL6
I2C_SDA2
NC4
SDA
SCL
1.8V
1.8V
1.8V
datasheet_x_ipod.DSN
Apple MFICO-Processor 2.0c
Regulatory compliance SPBT2632C1A
22/27 DocID022930 Rev 5
8 Regulatory compliance
8.1 FCC and IC– This module has been tested and found to comply with the FCC part 15 and IC
RSS-210 rules. These limits are designed to provide reasonable protection against harmful interference in approved installations. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference may not occur in a particular installation. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Modifications or changes to this equipment not expressly approved by the part responsible for compliance may render void the user’s authority to operate this equipment.
– Modular Approval, FCC and IC
FCC ID: X3ZBTMOD3
IC: 8828A-MOD3
In accordance with FCC part 15, the SPT2632C1A.AT2 is listed above as a modular transmitter device.
– Label instructions:
When integrating the SPBT2632C1A.AT2 into the final product, it must be
ensured that the FCC labelling requirements, as specified below, are satisfied.
Based on the public notice from FCC, the product into which the ST transmitter module is installed must display a label referring to the enclosed module.
The label should use wording such as the following:
Contains transmitter module
FCC ID: X3ZBTMOD3
IC: 8828A-MOD3
Any similar wording that expresses the same meaning may be used.
8.2 Bluetooth certificationModule with embedded stack and profile has been qualified according to SIG qualification rules:
– Bluetooth SIG qualified design, QD ID: B019224
– Product type: end product
– TGP version: Core 3.0
– Core spec version: 3.0
– Product descriptions: Bluetooth module, spec V3.0
DocID022930 Rev 5 23/27
SPBT2632C1A Regulatory compliance
27
8.3 CE certificationModule has been certified according to following certification rules:
– CE Expert opinion: 0447-ARSO00093-r
– Measurements have been performed in accordance with (report available on
request):
– EN 300 328 V 1.8.1 (2012:06) (a)
– EN 301 489-17 V 2.2.1 (2012:09) (b)
– EN 301 489-1 V1.9.2 (2011:09) (c)
– EN60950-1:2006 +A12:2011 (d)
• CE certified:
a. EN 300 328 V 1.8.1 (2012:06): “electromagnetic compatibility and radio spectrum Matters (ERM); Wideband transmission systems; data transmission equipment operating in the 2.4 GHZ ISM band and using wideband modulation techniques; harmonized EN covering essential requirements under article 3.2 of the R&TTE directive”.
b. EN 301 489-17 V 2.2.1 (2012:09): “electromagnetic compatibility and radio spectrum Matters (ERM); electromagnetic compatibility (EMC) standard for radio equipment and services; part 17: specific condition for 2.4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment”.
c. EN301 489-1 V 1.9.2 (2011 09): “electromagnetic compatibility and radio spectrum Matters (ERM); electromagnetic compatibility (EMC) standard for radio equipment and services; part 1: Common technical requirements”.
d. EN60950-1:2006 +A12:20011: “Information technology equipment - safety”.
Traceability SPBT2632C1A
24/27 DocID022930 Rev 5
9 Traceability
Each module is unambiguously identified by serial number stored in a 2D data matrix laser mark on the bottom side of the module itself.
The serial number has the following format:
WW YY D FF NNN
where
WW = week
YY = year
D = product ID family
FF = production panel coordinate identification.
NNN = progressive serial number.
Each module bulk is identified by a bulk ID.
BULK ID and module 2D data matrix are linked by a reciprocal traceability link.
The module 2D data matrix traces the lot number of any raw material used.
DocID022930 Rev 5 25/27
SPBT2632C1A Ordering information
27
10 Ordering information
Table 9. Ordering information
Order code Description Packing MOQ
SPBT2632C1A.AT2 Class 1 OEM Bluetooth antenna module JEDEC tray 1020 pcs
Revision history SPBT2632C1A
26/27 DocID022930 Rev 5
11 Revision history
Table 10. Document revision history
Date Revision Changes
23-Apr-2012 1 Initial release.
12-Jun-2012 2– Document status promoted from preliminary data to production
data
– Modified: Figure 1
07-Aug-2012 3– Added: notes in Table 6 and 7
– Modified: Section 7
29-Oct-2013 4 Added new section: Section 5.8, Section 7.3 and Section 9
12-Jun-2014 5 Updated: Features
DocID022930 Rev 5 27/27
SPBT2632C1A
27
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve theright to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at anytime, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes noliability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of thisdocument refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party productsor services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of suchthird party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIEDWARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIEDWARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWSOF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFESUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B)AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONSOR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS ATPURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT ISEXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRYDOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED AREDEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately voidany warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, anyliability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2014 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com