Basic Guide for GENEX Assistant 3.5.pdf

Post on 01-Feb-2016

327 views 118 download

Tags:

Transcript of Basic Guide for GENEX Assistant 3.5.pdf

Technology changes. Communication lasts 1

Basic Guide for

GENEX Assistant 3.5

HUAWEI TECHNOLOGIES CO., LTD.

Technology changes. Communication lasts 2

1. How to make a New Project… (step 1)

Click on New Project (Ctrl+N)

OR

Technology changes. Communication lasts 3

(step 2)

Insert your project name

Browse your target location

to save

Check your binning

Then…click “OK”

Technology changes. Communication lasts 4

2. How to load the logfiles…(step 1)

Click on Logfile Manager (Ctrl+F)

Technology changes. Communication lasts 5

(step 2)

Click “Add Logfile…” and browse

your location for target logfiles

Technology changes. Communication lasts 6

(step 3)

choose all your target logfiles and

click “Open”

Technology changes. Communication lasts 7

(step 4)

wait until all the logfiles loaded

and click “OK”

Technology changes. Communication lasts 8

3. How to group your test cases… (step 1)

Click on Analysis Group Manager (Ctrl+G)

Technology changes. Communication lasts 9

(step 2)

click “Add”

Technology changes. Communication lasts 10

(step 3)

step 1: insert the name of your test cases

step 2: select the test cases you want to grouping

step 3: click the arrow button in the middle and your selected test cases will move to the right

step 4: click “OK”

1

23

4

Note: In this cases, the Group Name is “2G UL” and the test cases for 2G UL is from MS1

based on the logfiles name [Q3_C4_SC02_2G_L4_MS1_UL_MS2_IDLE_SCANNER].

That’s why MS1 was moved to the right

Technology changes. Communication lasts 11

(step 4)

then click “OK”

Technology changes. Communication lasts 12

(step 5)

all the test cases you grouped will show here

Technology changes. Communication lasts 13

4. How to “Run” the logfiles…(step 1)

right click on “Analysis Group”, and click on “Run Analysis”

Technology changes. Communication lasts 14

(step 2)

Click “OK”

Technology changes. Communication lasts 15

(step 3)

wait until all the logfiles

finish to analyze

Technology changes. Communication lasts 16

(step 4)

this “KPI Result” table will appear once your

logfiles have been finish to analyze

Technology changes. Communication lasts 17

5. How to load the map… (step 1)

click on “View Map”

Technology changes. Communication lasts 18

(step 2)

click on “Layer Control” symbol

Technology changes. Communication lasts 19

(step 3)

Click “Add” and browse the location

of your map (.tab) files

Technology changes. Communication lasts 20

(step 4)

then click “OK”

Technology changes. Communication lasts 21

6. How to show the plotting…(step 1 - 4)

step 1: go to “Project” sidebar and select your grouped test cases

step 2: make sure your test cases is correct before you choose the plotting value

step 3: expand the features in the group

1

2

3

step 4: drag your chosen value into the map

Technology changes. Communication lasts 22

7. How to see the legend…(step 1)

click on “Enable/disable Legend” symbol

Technology changes. Communication lasts 23

(step 2)

then click “OK”

Select “Legend With Count And Percent”

Technology changes. Communication lasts 24

(step 3)

The legend will show like this

Technology changes. Communication lasts 25

8. How to modify the legend… (step 1)

Expand the “Data Layer” checkbox

click on “Map Layers” at the right side

of your GENEX Assistant

Technology changes. Communication lasts 26

(step 2)

Right click on the target legend

that you want to modify

Choose and click “Modify Legend”

Technology changes. Communication lasts 27

(step 3)

double click on the legend

you need to modify

Modify the legend that you need

Then, click “OK”

1

2

3Then, click “OK”4

Technology changes. Communication lasts 28

9. How to load Engineering Parameter… (step 1)

go to “Engineering Parameter” toolbar and choose which parameter

you want to load (GSM/WCDMA/LTE) depending on your project

Technology changes. Communication lasts 29

(step 2)

click on the GSM/WCDMA/LTE and click on “View Engineering Parameter”

Technology changes. Communication lasts 30

(step 3)

click on “Import BTS Config file” symbol

Technology changes. Communication lasts 31

(step 4)

then click “OK”

Browse your Engineering Parameter (.csv) file

Technology changes. Communication lasts 32

(step 5)

Make sure all the column name is synchronize

Then, click on “Apply the BTS Config” symbol

Technology changes. Communication lasts 33

(step 6)

Then, click “No”

wait until your Engineering Parameter loaded and

the below message box will appear once the process

is finish.

Technology changes. Communication lasts 34

10. How to edit Cell Label… (step 1)

right click on the map and click

on “Edit Cell Label”

Technology changes. Communication lasts 35

(step 2)

choose the value for

“DataSet:” and “Field” you

need to view.

then , click “OK”

Technology changes. Communication lasts 36

11. How to copy the map… (step 1)

click on this symbol to copy the current map

and paste on your document

Technology changes. Communication lasts 37

12. How to region the target analysis…(step 1)

click on “Add Region” symbol

Technology changes. Communication lasts 38

(step 2)

draw the border for your region and double click at the end of the border you draw

Technology changes. Communication lasts 39

(step 3)

click on “Save Region” symbol

Technology changes. Communication lasts 40

(step 4)

put the name for the region

cropped

then , click “OK”

Technology changes. Communication lasts 41

(step 5)

go to “Project” sidebar, right click on “Query” and

click on “New Query” to create a query for region

cropped

Technology changes. Communication lasts 42

(step 6)

Put the name for the query

Thick on the selected

region to use in the query

and click “Next”

Technology changes. Communication lasts 43

(step 7)

1

2

4

step 1: expand the features in “Available IE” box to

select the value you need to use in the region

step 2: select the value you need

step 3: click the arrow button in the middle and your

selected value will move to the right

step 4: click “OK”3

Note: In this cases, the value selected is “ServCellID”, “RxLev Sub” and “RxLev Qual” only

Technology changes. Communication lasts 44

(step 8)

Expand the “Query” and you can see the value

added to the region (only “ServCellID”, “RxLev

Sub” and “RxQual Sub” is shown). Only the plot

and value inside the region will be shown. All

plotting and value outside the region will be

excluded/dissappear.