Post on 02-Jun-2018
8/10/2019 B DVR UserGuide2
1/95
B-DVR
PEG-2
DIGITAL VIDEO RECORDER
Users Guide
Rev. 2.0.0
Darim Vision Co., Ltd.
8/10/2019 B DVR UserGuide2
2/95
B-DVR Users Guideii
8/10/2019 B DVR UserGuide2
3/95
B-DVR Users Guide iii
Notice
The information in this document is subject to change without prior notice in order to improve reliability,
design, or function and does not represent a commitment on the part of this company.
In no event will we be liable for direct, indirect, special, incidental, or consequential damages arising out
of the use or the inability to use the product or documentation, even if advised of the possibility of such
damages.
Copyright 2001 Darim Vision Co., Ltd.
All Rights Reserved.
No part of this reference manual may be reproduced or transmitted in any form or by any means without
the prior written permission of this company.
Throughout this manual, we make reference to product names that are trademarks of other companies.
We are using these names for identification purposes only, with no intention of infringement of the
trademarks.
FCC Information
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy an, if no installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one of more of the following measures:
l Reorient or relocate the receiving antenna.
l Increase the separation between the equipment and receiver.
l Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
l Consult the dealer or an experienced radio/TV technician for help.
8/10/2019 B DVR UserGuide2
4/95
NOTICE
B-DVR Users Guideiv
Shielded cables and I/O must be used for this equipment to comply with the relevant FCC regulations.
Changes or modifications not expressly approved in writing by Darim Vision Co. Ltd. May void the users
authority to operate this equipment.
Limited Warranty
Our company warrants this product against defects in materials and workmanship for a period of one year
from the date of purchase. During the warranty period, products determined by us to be defective in form
or function will be repaired or replaced at our option. This warranty does not apply if the product has
been damaged by accident, abuse misuse, or as a result of service or modification other than by us.
This warranty is in lieu of any other warranty expressed or implied. In no event shall we be held liable
for incidental or consequential damages, such as lost revenue or lost business opportunities arising from
the purchase of this product.
8/10/2019 B DVR UserGuide2
5/95
B-DVR Users Guide v
CONTENTS
1 INTSRUCTION _________________________________________________________ 1
2 SPECIFICATION _______________________________________________________ 3
3 FRONT PANEL AND REAR PANEL _______________________________________ 5
4 PREPARATION AND INSTALLATION _____________________________________ 7
4.1 What is in Package _________________________________________________ 7
4.2 Installation _______________________________________________________ 10
5 B-DVR FUNCTION ____________________________________________________ 17
5.1 Front Panel Button ________________________________________________ 17
5.2 VFD Display _____________________________________________________ 19
5.3 Basic Function ____________________________________________________ 20
5.4 JOG-SHUTTLE Function __________________________________________ 26
5.5 MARK Button ____________________________________________________ 29
5.6 BOOKMARK Button ______________________________________________ 32
5.7 JUMP Function ___________________________________________________ 33
6 B-DVR MENU _________________________________________________________ 35
6.1 Main Menu ______________________________________________________ 35
6.2 DVR Setup _______________________________________________________ 37
6.3 Screen Setup _____________________________________________________ 39
6.4 Video Setup ______________________________________________________ 41
6.5 Schedule Setup ___________________________________________________ 43
8/10/2019 B DVR UserGuide2
6/95
CONTENTS
B-DVR Users Guidevi
6.6 System Info ______________________________________________________ 46
6.7 Play-List _________________________________________________________ 49
6.8 ALL CLIPS ______________________________________________________ 51
6.9 Playing the Play-List _______________________________________________ 52
6.10 Playing the ALLPLAYLISTS _______________________________________ 54
6.11 Editing Play-List __________________________________________________ 55
6.12 Changing names of the Play-List _____________________________________ 58
6.13 Deleting the Clip from the Play-List __________________________________ 60
6.14 Managing Clip-List ________________________________________________ 62
6.15 Play Clip-List Items _______________________________________________ 63
6.16 Change the names of the Clip-List items ______________________________ 64
6.17 Delete Clip-List Items ______________________________________________ 66
7 B-DVR DESKTOP SOFTWARE __________________________________________ 69
7.1 B-DVR Desktop Software ___________________________________________ 70
7.2 Clip-List Menu ___________________________________________________ 71
7.3 Play-List Menu ___________________________________________________ 73
7.4 B-DVR Hard Disk Optimization _____________________________________ 74
7.5 Settings __________________________________________________________ 75
8 HARD DISK MANAGEMENT AND HOW TO USE __________________________ 79
8.1 B-DVR Hard Disk Jumper Setting ___________________________________ 79
8/10/2019 B DVR UserGuide2
7/95
CONTENTS
B-DVR Users Guide vii
8.2 How to use B-DVR HDD on general PC _______________________________ 79
9 TROUBLESHOOTING __________________________________________________ 81
9.1 How to solve the trouble of B-DVR ___________________________________ 81
9.2 Messages occurred B-DVR activation _________________________________ 83
9.3 Upgrade Information and Technical Support __________________________ 86
8/10/2019 B DVR UserGuide2
8/95
CONTENTS
B-DVR Users Guideviii
8/10/2019 B DVR UserGuide2
9/95
8/10/2019 B DVR UserGuide2
10/95
INSTRUCTION
B-DVR Users Guide2
8/10/2019 B DVR UserGuide2
11/95
B-DVR Users Guide 3
2 SPECIFICATION
eature Spec Remark
Storage Removable Hard disk (IDE)
Storage capacity 20GB/40GB/60GB/80GB/120GB/250GB
Compression MPEG-2 Video, MPEG 1 Layer II Audio
Video ormat CCIR601 NTSC/PAL
Video Input
Composite
S-Video
Video Output
Composite
S-Video
YUV Component
RGB
Audio Input
Stereo RCA (47 Unbalanced)
Audio Output Stereo RCA (600 Unbalanced)
Recording ormat
NTSC 704x480 at 30FPS
PAL 704x576 at 25FPS
Compression
(Constant Bit-rate)
Normal Compression rate : 4.5Mbps
Super Compression rate : 6.0Mbps
Maximum recording
time
40hours (30fps, 4.5Mbps, Normal Audio) With 80GB Hard disk
30hours (30fps, 6.0Mbps, Normal Audio)
Scheduled recording Off/Playback/Record (Max.10 Schedules)
Play List
Max 300 Video Clips
Title Edit
List Edit
Making a clip by Mark In/OutPlayback Mode Repeat, Once
ront Panel Time Code/List Information Display
Shuttle
2 ,4x,8x,16x
Slow Motion 1/2x,1/4x,1/8x
Jog Yes
ront Display Device
VFD
OSD Menu Yes
Serial Interface
RS232/RS422 (SONY Protocol)
8/10/2019 B DVR UserGuide2
12/95
8/10/2019 B DVR UserGuide2
13/95
B-DVR Users Guide 5
3 FRONT PANEL AND REAR PANEL
[Picture 3.1] Front Panel and Names
1 POWER button 11 PLAY button
2 Shuttle ring 12 STOP button
3 Jog 13 PASUE/STILL button
4 VFD window 14 DISPLAY button
5 (Right-hand direction) button 15 RECORD button
6 LIST button 16 MARK OUT button
7 (Upward) button 17 (Downward) button
8 MENU button 18 SELECT button
9 (Left-hand direction) button 19 MARK IN button
10 1 ~ 5 button 20 BOOKMARK button
8 7 510 9 6 4 3
11121314151617181920
12
8/10/2019 B DVR UserGuide2
14/95
FRONT PANEL AND REAR PANEL
B-DVR Users Guide6
[Picture 3.2] Rear Panel and Names
1 S-Video input 9 Cooling Fan
2 S-Video output 10 Composite Video input
3 Composite Video output 11 Audio Left input
4 Audio Left output 12 Audio Right input
5 Audio Right output 13 Power cord
6 B/R-Y output
7 G/B-Y output
8 R/Y output
9 2
13 12 11
134
10
8 57 6
8/10/2019 B DVR UserGuide2
15/95
B-DVR Users Guide 7
4 PREPARATION AND INSTALLATION
4.1 What is in Package
[Picture 4.1] B-DVR Power cord 1 unit
[Picture 4.2] Composite cable 2 units
[Picture 4.3] S-Video cable 2 units
8/10/2019 B DVR UserGuide2
16/95
PREPARATION AND INSTALLATION
B-DVR Users Guide8
[Picture .4] 80GB Hard Disk (installed in the B-DVR originally but optional in some
cases)
[Picture 4.5] Hard Disk Rack 1 unit(installed in the B-DVR)
[Picture 4.6] B-DVR Desktop(Hard Disk Utility) Software for PC
8/10/2019 B DVR UserGuide2
17/95
PREPARATION AND INSTALLATION
B-DVR Users Guide 9
[Picture 4.7] Users Guide
[Picture 4.8] Limited Warranty
8/10/2019 B DVR UserGuide2
18/95
PREPARATION AND INSTALLATION
B-DVR Users Guide10
4.2 Installation
4.2.1 Plug in the power cordMake sure to read the installation instruction in detail before plug in the power cord. Before
connecting B-DVR to other device, plug in the power cord according to the instruction in this
chapter. The power cord protects B-DVR from the electrical damage by ground. Follow
the instruction.
Installation .
Make sure the mentioned usable voltage limit of the B-DVR back panel suits the type of
voltage system to be connected. The voltages (220V/50Hz, 220V/60Hz) are suitable for
B-DVR. Confirm again the voltage type to be connected before connecting.
Installation 2.
Connect the end of B-DVR power cord to the socket of the B-DVR back panel.
Installation 3.
Plug in the other end of power cord into the grounded 3-hole receptacle or the multi-hole
outle .
Note)B-DVR is ground safe and has 3-line grounded plug. Consult to the engineer if you can't
plug the power cord grounded AC receptacle.
[Picture 4.9] Connected power cord to B-DVR
8/10/2019 B DVR UserGuide2
19/95
PREPARATION AND INSTALLATION
B-DVR Users Guide 11
4.2.2 Connection AV device to B-DVR
You can connect various kinds of AV devices including general AV I/O devices mentioned
in the chapter. Please refer the manufacture's guide if you are going to connect other
devices.
The B-DVR can be connected with various I/O devices or its own use. Refer to the following
table according to the type of input or output. There are Composite Cable, S-Video Cable
and RGB Cable in the B-DVR.
Video input Video output Audio input Audio output
Composite cable O O O O
S-Video cable O O X X
RGB cable X O X X
[Table 4.1] Supported input/output cable in B-DVR
8/10/2019 B DVR UserGuide2
20/95
PREPARATION AND INSTALLATION
B-DVR Users Guide12
Follow the instruction to connect each cable at the following.
Sample.1)Connect S-Video into input connector and use the monitor to play from B-DVR
Composite, S-Video and RGB.
[Picture 4.10] In the situation for S Video input and S-Video output
8/10/2019 B DVR UserGuide2
21/95
PREPARATION AND INSTALLATION
B-DVR Users Guide 13
[Picture 4.11] For S-Video input and Composite output
[Picture 4.12] For S-Video input and RGB output
8/10/2019 B DVR UserGuide2
22/95
PREPARATION AND INSTALLATION
B-DVR Users Guide14
Sample.2)Connect Composite to input connector port and use monitor to play from B-DVR
Composite, S-Video and RGB.
[Picture 4.13] For Composite input and S-Video output
8/10/2019 B DVR UserGuide2
23/95
PREPARATION AND INSTALLATION
B-DVR Users Guide 15
[Picture 4.14] For Composite input and Composite output
[Picture 4.15] For Composite input and RGB output
8/10/2019 B DVR UserGuide2
24/95
PREPARATION AND INSTALLATION
B-DVR Users Guide16
8/10/2019 B DVR UserGuide2
25/95
B-DVR Users Guide 17
5 B-DVR FUNCTION
5.1 Front Panel Button
[Picture 5.1] B-DVR Front Panel Button
1 POWER button 11 PLAY button
Press to switch on/off B-DVR. Start to play
2 Shuttle ring 12 STOP button
Shuttle clockwise direction(FF) or
counterclockwise direction(FB) and AV
data is 2x/4x 8x/16x.
Stop playback/recording.
3 Jog 13 PAUSE/STILL button
Searching by one frame forward or
backward after pause.
Pause playing.
4 VFD window 14 DISPLAY button
Display B-DVR information. Display time or List in the VFD
indow.
5 (Right-hand direction) button 15 RECORD button
Moves in the Menu setup and from the list
to the item or to the clip. Search forward by
5% in pause mode.
Record the video source input.
6 LIST button 16 MARK OUT button
Push to convert to the Play-List menu Finish to edit the necessary
ideo source in play mode.
8 7 510 9 6 4 3
11121314151617181920
12
8/10/2019 B DVR UserGuide2
26/95
B-DVR FUNCTION
B-DVR Users Guide18
7 (Upward) button 17 (Downward) button
Change the setup value of item. Change the setup value of item.
8 MENU button 18 SELECT button
Convert to the Main menu. Select the item.
9 (Left-hand direction) button 19 MARK IN buttonMoves to the item in the Menu setup and
List. Moves back to the clip in playback in
the Play-list. Search backward by 5% in
pause mode.
Start to edit the necessary video
source in play mode.
10 1 ~ 5 button 20 BOOKMARK button
Push 1- 5 for bookmark. Bookmark to make it easy to
select in clip play mode.
8/10/2019 B DVR UserGuide2
27/95
B-DVR FUNCTION
B-DVR Users Guide 19
5.2 VFD Display
[Picture 5.2] VFD window display
1) ALARM) display
Indicates the schedule setup for playing or recording on the defined date and time.
2) REC display
Indicates the video source is being recorded.
3) FB, PAUSE, PLAY, FF display
Indicates B-DVR is occupied in Fast backward, Pause, Play and Fast forward.4) Counter display
Indicates the system time display, list information, recording time and playback time.
8/10/2019 B DVR UserGuide2
28/95
B-DVR FUNCTION
B-DVR Users Guide20
5.3 Basic Function
5.3.1 DISPLAY Button
[Picture 5.3] DISPLAY button
DISPLAY button enables users to select the contents of VFD window either Time displayor
List Information display. When you press DISPLAY button once, the Time display
is shown. If you press DISPLAY button again, the List Information display is shown.
Two display contents are shown in terns when you press the button continuously.
Note that DISPLAY button is only activated in the STOP mode. It doesn't work in other
modes.
5.3.1.1 Time Display
The RTC(Real Time Clock)is installed in the B-DVR which is used in the whole system and
user can setup the time and date in the DVR setup from the Main Menu. he setup time and
date run when the power is off and it is used when necessary like schedule function. You can
use this function when you want to display the setup time.
[Picture 5.4] Example of time display
[Picture 5.4] shows the present setup time in the B-DVR. It is 03-12 12:05:25 and means
8/10/2019 B DVR UserGuide2
29/95
8/10/2019 B DVR UserGuide2
30/95
B-DVR FUNCTION
B-DVR Users Guide22
related to playback. It means to proceed for 12 hour 05 minutes 25 seconds from
the starting point of video source. indicates playback. Once you press PLAY button,
it displays the saved MPEG-2 file to a monitor or to other AV device through video output port.
Press STOP button shown in [Picture 5.7] to stop playback command.
5.3.2.1 SLOW Playback
During play, press button in case that the customer wants slow playback. With the
pressing of button once, twice, and three times, playback goes to 1/2x, 1/4x, 1/8x. To stop
the execution of slow playback, press PAUSE button. as shown at [Picture 5.10].
5.3.3 STOP Button
[Picture 5.7] STOP utton
You can stop the command processing by pressing STOP button in record, playback and pause
modes. When pressing STOP button, the Time-Code information related to the recording,
playback and pause command disappears in the VFD window and the selected Display from
either Time Display or List Information Display appears in the VFD window.
Pressing STOP button to stop all the command processing, MENU button and LIST button areready to activate. Therefore, to setup Main Menu and to command or to edit List Information
are only possible in the stop mode.
8/10/2019 B DVR UserGuide2
31/95
B-DVR FUNCTION
B-DVR Users Guide 23
5.3.4 RECORD Button
[Picture 5.8] RECORD button
The B-DVR can record the video connected from the input port in real time in MPEG-2 file to
the installed Hard Disk. After switching on the power, B-DVR is ready to activate by
initializing the installed Hard Disk or preparing to record. With this function, you can record
video source instantly in real time. Therefore, once B-DVR activates, it is always ready to
record and save.
[Picture 5.9] VFD display in record mode
Press RECORD button to record the video source presently input to the B-DVR. It is shown
in VFD window as [Picture 5.9] simultaneously by pressing RECORD button. The
12:05:25 displays the Time-Code value related to the recording. It means the time to be
recorded for 12 hour 05 minutes 25 seconds from the beginning points. " REC "
displays recording.
When you press RECORD button, it records and saves the input video source from the input
port in real time in MPEG-2 file to the installed Hard Disk. It registers the saves file in the
Clip-List. The latest recording file is registered in No.00 which is highest order of Clip-List.
If you want to play other clip, you can play it in the Clip-List referring playback.
Press STOP button to stop record command processing.
8/10/2019 B DVR UserGuide2
32/95
B-DVR FUNCTION
B-DVR Users Guide24
5.3.5 PAUSE Button
[Picture 5.10] PAUSE button
5.3.5.1 PLAY Pause
You can pause play command processing pressing PAUSE button in play mode. In pause
mode, you can use search function using Jog and Shuttle. The Time-Code value of the
allocated position of video source in pause mode shows in the VFD window and it enables users
to search the file exactly.
[Picture 5.11] VFD display in play pause mode
Press PAUSE button when you want to pause in play mode. The display shown in [Picture
5.11] appears when pressing PAUSE button. The 12:05:25 indicates the Time-Code value
related to pause. It means to pause for processing for 12 hour 05 minutes 25 seconds
from the beginning point. indicates pause.
Press STOP button or PLAY button to stop pause command processing.
5.3.5.2 RECORD Pause
You can pause record command processing pressing PAUSE utton in record mode.
8/10/2019 B DVR UserGuide2
33/95
B-DVR FUNCTION
B-DVR Users Guide 25
[Picture 5.12] VFD display in record pause mode
Press PAUSE button when you want to pause in record mode. The display shown in [Picture
5.12] appears when pressing PAUSE button. The 12:05:25 indicates the Time-Code value
related to pause. It means to pause for processing for 12 hour 05 minutes 25 seconds
from the beginning point. indicates pause.
Press STOP button or RECORD button to stop pause command processing.
8/10/2019 B DVR UserGuide2
34/95
B-DVR FUNCTION
B-DVR Users Guide26
5.4 JOG-SHUTTLE Function
[Picture 5.13] Jog-Shuttle
The B-DVR has Jog-Shuttle function in order to search conveniently. The function of Jog
activates in pause mode, pressing PAUSE button during the play mode. The function ofShuttle activates either in play mode or in pause mode. Jog is used for searching still image,
Shuttle is used for fast searching like at 2x, 4x, 8x, 16x speed.
5.4.1 JOG Function
JOG function activates in pause mode while the video source is playing. You can search by
one frame either forward or backward in the position of pause. When you turn the Jog in
clockwise direction from the front side, the still image being played by one frame in the
direction of normal playback. When you turn the Jog in counter clockwise direction from the
front side, the still image is being played by one frame backward.
5.4.2 SHUTTLE Function
SHUTTLE starts in the play or pause mode. By turning the Shuttle clockwise or
counterclockwise, slowly or fast. The wanted video clip can be searched.
While Shuttle for Fast Forward or Fast Rewind being used, Screen and VFD window show
different signals as following pictures :
Jog
Shuttle
8/10/2019 B DVR UserGuide2
35/95
B-DVR FUNCTION
B-DVR Users Guide 27
[Picture 5.14] Fast Forward on screen
[Picture 5.15] Fast Forward on VFD
[Picture 5.16] Fast Rewind on screen
8/10/2019 B DVR UserGuide2
36/95
B-DVR FUNCTION
B-DVR Users Guide28
[Picture 5.17] Fast Rewind on VFD
8/10/2019 B DVR UserGuide2
37/95
B-DVR FUNCTION
B-DVR Users Guide 29
5.5 MARK Button
[Picture .18] MARK IN, MARK OUT button
Marking can select the wanted video by marking the starting and ending part and then make
new video clip. Using Marking, it is easy to make required clip from already recorded
video clip without using an editing tool or re-recording video. As shown at [Picture 5.18],there are two buttons; MARK IN for indicating the starting part and MARK OUT for the
ending part.
5.5.1 Using Marking Function
Refer to 6.15.1 Play Clip-List Items and select a video clip to apply to the Marking
function.
Make sure that the selected video clip is viewed as pause on the screen. Press the PLAY button and play till new clip is to start or use the Jog & Shuttle to the
starting part for new clip and then press PAUSE button.
Press MARK IN button in the state of pause.
8/10/2019 B DVR UserGuide2
38/95
B-DVR FUNCTION
B-DVR Users Guide30
[Picture 5.19] MARK IN
OSD appears as shown at the [Picture 5.19] in the normal operation and performs Mark In.
Press PLAY button again until the ending part of the video for the new clip or use Jog &
Shuttle and then press PAUSE button.
Press MARK OUT button in the state of pause.
[Picture 5.20] MARK OUT
OSD appears as shown at the [Picture 5.20] in the normal operation and performs Mark
Out.
After Mark In and Mark Out are done, new clip named MARK## is added on the Clip-List.
8/10/2019 B DVR UserGuide2
39/95
B-DVR FUNCTION
B-DVR Users Guide 31
[Picture 5.21] New Clip
8/10/2019 B DVR UserGuide2
40/95
B-DVR FUNCTION
B-DVR Users Guide32
5.6 BOOKMARK Button
[Picture 5.22] BOOKMARK button
BOOKMARK is the function that reminds the information on whereabouts of clips in the work
of Play-List or Clip-List and that helps the clips to directly move the specific clip. The
maximum five units of specific clips can be saved on the BOOKMARK. With the pressing
of number 1 ~ 5 , all the clips move to the specific clip saved previously and standby.
5.6.1 Using Bookmark Function
Refer to 6.15.1 Play Clip-List Items and select a video clip to apply to the Bookmark
function.
Make sure that the selected video clip is viewed as pause on the screen. Press the PLAY button and play till the video clip to be saved to the Bookmark function or
use the Jog & Shuttle and then press PAUSE button.
Press BOOKMARK button in the state of pause. After pressing BOOKMARK button, press umber among 1 ~ 5 .
In the state of stop or pause from the selected number 1 ~ 5 , video clips can
always be moved to the saved specific clip.
8/10/2019 B DVR UserGuide2
41/95
B-DVR FUNCTION
B-DVR Users Guide 33
5.7 JUMP Function
In case that the size of the recorded clip is large, it takes to long time to move to the certain
position with Jog & Shuttle. JUMP function helps to move to the wanted position with ease.
It searches very fast regardless of the size of the clip. There is a function of skimmingthrough using JUMP function. Out of 100% Clip you can skip 5% or 1% either forward or
backward you can control the JUMP function from 0%95% that you can easily search the
video.
5.7.1 Using JUMP Function
Refer to 6.15 Play Clip-List Items and select a video clip to apply to the JUMP function.
Make sure that the selected video clip is viewed as pause on the screen.
Using button and button, search goes forward or backward by 5% and with
button and button, it goes forward or backward by 1%.
[Picture 5. 3] 50% JUMP example [Picture 5.24] 75% JUMP example
8/10/2019 B DVR UserGuide2
42/95
B-DVR FUNCTION
B-DVR Users Guide34
8/10/2019 B DVR UserGuide2
43/95
B-DVR Users Guide 35
6 B-DVR MENU
6.1 Main Menu
Main Menu appears after pressing the MENU button as shown the below picture. Refer to[Picture 6.2]
[Picture 6.1] MENU button
There are four items on the Main Menu.
DVR Setup : Play mode, Beep, Date and Time can be set.
Screen Setup : OSD related can be set.
Video Setup : Input and output, and video compression rate can be set.
Schedule Setup : Schedules to play or record can be set.
System Info :Displays settings and system version information.
Also Main Menu shows the current B-DVR version. The [Picture 6.2] shows version 2.0.
8/10/2019 B DVR UserGuide2
44/95
B-DVR MENU
B-DVR Users Guide36
[Picture 6.2] Main Menu Screen
6.1.1 General Setting
The above screen appears on pressing MENU utton.
Using , button to move to each item, and select the item and press the SELECT
button.
[Picture 6.3] SELECT button
To move item, use , button.
To change the value, use , button.
To end the Main Menu, press the MENU button again.
8/10/2019 B DVR UserGuide2
45/95
B-DVR MENU
B-DVR Users Guide 37
6.2 DVR Setup
Language, Date and Time, Play Mode and Buzzer can be set in DVR Setup.
[Picture 6.4] DVR Setup
There are five items set in DVR Setup.
Language : Language, used for the entire system, can be set.
Date : Date can be set.
Time : Time can be set.
Play Mode : Play times(Once or Repeat) can be set.
Buzzer : On or Off can be set.
6.2.1 General Setting
Main Menu appears on pressing MENU button.
Using , button, move to the DVR Setup.
On pressing SELECT button, DVR Setup is done as shown on [Picture 6.4].
To change the item, use , button, to move to Language, Date, Time ,
Play Mode, Buzzer.
To change the value, use , button.
8/10/2019 B DVR UserGuide2
46/95
B-DVR MENU
B-DVR Users Guide38
The following shows the value of each item.
Menu Category Value
DVR Setup
Language English, Korean
Year 2002 ~ 2099Month 01 ~ 12
Day 01 ~ 31(30/29/28)
Hour 00 ~ 23
Min 00 ~ 59
Sec 00 ~ 59
Play Mode Repeat : Repeats playing a clip.
1(Pause) : Plays once then pauses at the end of clip.
1(Stop) : P ays once then goes back to live mode.
Buzzer On, Off
After setting all values, press the MENU button to return to Main Menu.
To end the Main Menu, press the MENU button again.
8/10/2019 B DVR UserGuide2
47/95
B-DVR MENU
B-DVR Users Guide 39
6.3 Screen Setup
Screen Setup sets the OSD modes.
[Picture 6.5] Screen Setup
Screen Setup has following items:
Online Info : can set OSD(On Screen Display).
6.3.1 General Setting
Main Menu appears on pressing MENU button.
Using , button, move to the Screen Setup.
On pressing SELECT button, Screen Setup is done as shown on [Picture 6.5].
Using , button, value can be set.
The following shows the value of each item.
Value Contents
Detail
1. Command appears on the upper left.
2. OSD shows the information on Command on the
upper right.
8/10/2019 B DVR UserGuide2
48/95
8/10/2019 B DVR UserGuide2
49/95
B-DVR MENU
B-DVR Users Guide 41
6.4 Video Setup
Video Setup is a port where the input and output are determined. The resolution of video
recording is also selected. B-DVR accepts both PAL(25fps) and NTSC(30fps). When the
NTSC TV set is used, be sure to connect an NTSC video source to the input port becausedefault output is set to the PAL when turning on power without video input signal. B-DVR
default Video Setup input is Composite and out put is S-Video (Composite), respectively.
Such setup is also applied when a new Hard Disk is connected.
Quality represents the degree of compression when digitizing input video the Hard Disk in
MPEG-2 format. The quality is determined by amount of data in MPEG-2 stream per second
measured in Mbps. Higher numbers represent better quality but consume more Hard Disk
space.
In B-DVR the quality level can chosen between 4.5Mbps(Normal) and 6.0Mbps(Super).
[Picture 6.6] Video Setup
There are three items in Video Setup.
Input : can set the video input port.
Output : can set the video output port.
Quality : can set the bit-rate of video.
8/10/2019 B DVR UserGuide2
50/95
B-DVR MENU
B-DVR Users Guide42
6.4.1 General Setting
Main Menu appears on pressing MENU button.
Using , button, move to the Video Setup.
On pressing SELECT, Video Setup is done as shown on [Picture 6.6].
Using , button, move to Input, Output, Quality. To change the value, use , button.
The following shows the value of each item.
Item Value Contents
InputComposite
S-Video
Output
S-Video(Composite)
RGB
Component YUV
Quality Normal Bit-Rate : 4.5MbpsSuper Bit-Rate : 6.0Mbps
After setting all values, press the MENU button to return to Main Menu.
To finish the Main Menu, press the MENU button again.
8/10/2019 B DVR UserGuide2
51/95
B-DVR MENU
B-DVR Users Guide 43
6.5 Schedule Setup
Enables to set up 10 schedules of starting and ending hours. The following steps explain how
to set up for the schedule.
[Picture 6.7] Schedule Setup
6.5.1 General Setting
Press MENU button to display Main Menu.
To go to Schedule Setup, use , buttons.
Press SELECT button, then move to Schedule Setup screen. It displays as shown in
[Picture 6. ].
Use , buttons to move to the category the user needs to change the value.
8/10/2019 B DVR UserGuide2
52/95
B-DVR MENU
B-DVR Users Guide44
[Picture 6.8] Schedule Setup
On Schedule Edit screen showing above, Current Time displays the current hour thatis already setup. Number shows the order of schedule. To move to other schedules,
use , buttons after selecting the menu Number.
Start Time shows the starting hour of recording and playing. To setup the hour of
Start Time , select the menu Hour and Min, then use , buttons to change
the value.
End Time shows the ending hour of recording and playing. To setup the hour of End
Time, select the menu Hour and Min, then use , uttons to change the
value
The menu Mode designates either schedule recording or playback the clips which can
be selected by the user.
In case the value Record is selected, the user enables to select the Bitrate
(Normal/Super) by using , buttons.
In case the value Play is selected, the user enables to select Play List(All Clips/All
PlayLists/PlayList) by using , buttons.
The menu revious shows the starting, ending time and mode of the previous schedule.
The menu Next shows the starting, ending time and mode of the next schedule.
When the starting and ending time for schedule are set as 00:00, the system does not
operate either Recording or Playback.
Press MENU button to return to the Main Menu.
Press MENU button again to finish the Main Menu. If record/play schedule is setup
8/10/2019 B DVR UserGuide2
53/95
B-DVR MENU
B-DVR Users Guide 45
on the specified time, then the alarm in red will be displayed on VFD window as
shown in [Picture 6.9].
[Picture 6.9] Example of Schedule Setup
8/10/2019 B DVR UserGuide2
54/95
B-DVR MENU
B-DVR Users Guide46
6.6 System Info
On System Info screen, it shows the general information of system including hard disk quota.
The menu Factory Setting is to set up to default setting.
[Picture 6.10] System Info
6.6.1 General Setting
Press MENU button to display Main Menu.
To go to System Info screen, use , buttons.
Press SELECT button, then move to System Info screen. It displays as shown [Picture
6.10].
Explanation pertaining to each category is as shown on the following chart.
8/10/2019 B DVR UserGuide2
55/95
B-DVR MENU
B-DVR Users Guide 47
Menu Category Explanation Location Available for
Designation
Date The date that is set up by user. DVR Setup
Time The time that is set up by user. DVR Setup
S/W Ver. Software version of systemTotal Total capacity of using hard disk
Available Remaining capacity of using hard disk
Online Info OSD(On Screen Display) Screen Setup
Input Video input port Video Setup
Output Video output port Video Setup
Quality Bitrate Video Setup
The following picture shows the screen when the menu Factory Setting is selected.
[Picture 6.11] Factory Setting
Use , buttons to select the value YES to initialize the value of menu setup or
select the value NOto keep a current value of the menu.
Setting is completed when Select button is pressed.
Press MENU button to return the Main Menu.
Press MENU button again to finish the Main Menu.
The following table shows the default values of menu.
8/10/2019 B DVR UserGuide2
56/95
B-DVR MENU
B-DVR Users Guide48
Menu Menu Category Initial Value
DVR Setup Play Mode 1 (Pause)
Buzzer On
Screen Setup Online Info DetailVideo Setup Input Composite
Output Composite/S-Video
Quality Normal
Schedule Setup Record on Schedule Off
Start Time 00 : 00
End Time 00 : 00
Mode Record
8/10/2019 B DVR UserGuide2
57/95
B-DVR MENU
B-DVR Users Guide 49
6.7 Play-List
Press LIST button on the B-DVR front panel, then the Play-List Menu(refer to [Picture 6.13])
which you can setup the whole MPEG-2 file saved in the B-DVR displays.
[Picture .12] LIST button
There are 5 commands of the Play-List Menu as followings :
LAY : command to play the selected Play-List.
EDIT : command to edit the selected Play-List.
NAME : command to specify the name of selected Play-List.
CLEAR : command to delete the Play-List.
CLIP : command to move to Clip-List that manages all clips of Hard Disk.
8/10/2019 B DVR UserGuide2
58/95
B-DVR MENU
B-DVR Users Guide50
[Picture 6.13] Play-List Menu Display
6.7.1 General Processing
Press LIST button to display Play-List Menu.
Move to the specified item of Play-List using , button..
After moving to each command using , button, press SELECT button to process
the selected command on the item of Play-List.
Press LIST button again to finish Play-List Menu display.
8/10/2019 B DVR UserGuide2
59/95
B-DVR MENU
B-DVR Users Guide 51
6.8 ALL CLIPS
All the recorded clips of B-DVR are shown in [Picture 6.14]. There is always the item called
ALL CLIPS at No.00 in the Play-List. The item ALL CLIPS means that it includes all the
clips saved in the Hard Disk. You can see all the saved video source of B-DVR in saved order,if selecting the ALL CLIPS item.
[Picture 6.14] ALL CLIPS Display
In the ALL CLIPS item, only PLAY command among PLAY, EDIT, NAME and
CLEAR activates. In PLAYcommand processing, it plays without waiting status unlike the
items of other Play-List. However the latest recorded file appears close to No.00. Although
ALL CLIPS that was recorded in previous times cannot view when it is played after DELETED
from the Clip in the Clip-List, it may appear on the display. The items from No.01 to No.29
of the Play-List can process all the commands of LAY,EDIT, NAMEand CLEAR.In the Play command processing, the item is on waiting status and starts to play pressing PLAY
button.
The information about the total size of installed Hard Disk(total : 37GB in [Picture 6.14]) and
the usable size of Hard Disk storage (free 34GB in [Picture 6.14]) are displayed in the ALL
CLIPS display.
8/10/2019 B DVR UserGuide2
60/95
B-DVR MENU
B-DVR Users Guide52
6.9 Playing the Play-List
You can make total of 29 play lists except ALL CLIPS and ALL PLAYLISTS category.
You can edit from all 29 saved different clips from the lists from 01-29 you can execute
PLAY, EDIT, and CLEAR, CLIP.
[Picture 6.15] Select Play-List PLAY command
If you select any of the clips from 01-29, except ALL CLIPS and ALL PLAYLISTS , you
can view the file size for each selected clips. [Picture 6.15] shows that 134Mbytes are being
used.
6.9.1 Play Command
Press LIST button, Play-List Menu will pop up. Use , button to move up and down to choose to play any Play- Lists from 00 ~ 30
Play-List as shown in [ Picture 6.15], it chose DARIM for your example.
You can use , buttons for play to select the location where to play, as it is shown
in [Picture 6.15].
Press SELECT button to PLAYin any selected from the play list.
WhenPLAYcommand is being activated, Play-list Menu will disappear automatically and
at the same time the screen will show the video in Pause mode to be ready to play from the
paused video screen.
8/10/2019 B DVR UserGuide2
61/95
B-DVR MENU
B-DVR Users Guide 53
Press PLAY button to play the video.
8/10/2019 B DVR UserGuide2
62/95
B-DVR MENU
B-DVR Users Guide54
6.10 Playing the ALLPLAYLISTS
There is always the item called ALL PLAYLISTS at No.30 in the Play-List. The item ALL
PLAYLISTS means that it includes all the Play-Lists saved in the Hard Disk. In the ALL
PLAYLISTS item, only PLAYcommand among PLAY, EDIT, NAME and CLEARactivates.
[Picture 6.16] ALL PLAYLISTS PLAY command
6.10.1 Play Command
Press LIST button, Play-List Menu will pop up.
Use , button to move up and down to choose to play ALL PLAYLISTS.
You can use , buttons for play to select the location where to play, as it is shown
in [ 6.16].
Press SELECT button to PLAY.
WhenPLAYcommand is being activated, Play-list Menu will disappear automatically and
at the same time the screen will show the video in Pause mode to be ready to play from the
paused video screen.
Press PLAY button to play the video.
8/10/2019 B DVR UserGuide2
63/95
B-DVR MENU
B-DVR Users Guide 55
6.11 Editing Play-List
From the Play-List, you can select one Clip to group the related videos to make the one specific
Clip to play repeatedly and continuously.
[Picture 6.17] Select Play-List EDIT Command
6.11.1 EDIT Command
Press LIST button and Play-List Menu to show up on the screen.
Use , button to select any numbers from 01 ~ 29(Except ALL CLIPS and ALL
PLAYLISTS) and move to any of the Play-List to EDIT. Example in [Picture 6.17] it
selected DARIM.
In order toEDITUse , button to select EDIT as shown in [Picture 6.17].
Press SELECT button to EDIT in selected Play-List.
8/10/2019 B DVR UserGuide2
64/95
B-DVR MENU
B-DVR Users Guide56
[Picture 6.18] Play-List for Editing display
WhenEDITcommand is executed, Play-List Menu will disappear automatically and the
display will change to Play-List Edit as shown in the [Picture 6.18]. Use , button
to select OK, EDIT, UP, DOWN,DELETE in the Play-List to locate to place
in designated Clip.
Each command Explanations are in the followings :
OK : After Editing finished, move back to Play-List Menu.
EDIT : Selecting or changing the related Clip from the Clip-List.
UP : Move upward the related Clip
DOWN : Move downward the related Clip
DELETE: Delete the related Clip from the Clip-List
Select EDITfrom the commands above and use , button to located the new Clipin the Clip-List or you can choose to change the Clip if desired. Refer to [Picture 6.19].
8/10/2019 B DVR UserGuide2
65/95
B-DVR MENU
B-DVR Users Guide 57
[Picture 6.19] Play-Lists Clip for Editing Display
Select the new location of the Clip and press SELECT button.
After checking the Changed Clip, select OKto go back to Play-List Menu.
After finishing editing, if you want to check the Clips from the Play-List, go to Play-List
Menu and use , button to select PLAY and press SELECT button.
The edited Play-List is ready to play. Press PLAY button to check to view.
8/10/2019 B DVR UserGuide2
66/95
B-DVR MENU
B-DVR Users Guide58
6.12 Changing names of the Play-List
The name of Play-List can be changed easily except ALL CLIPS and ALL PLAYLISTS.
The maximum 12 characters can be used including alphabet letters and numbers. If the name
is not valid or if the Clip is deleted from the Play-List, the clip PLAYLIST # clip name willappear.
[Picture 6. 0] Changing the name of the Clip in Play-List
6.12.1 NAME Command
Press LIST button. Play-List Menu will appear.
Use , button to select from 01 ~ 29 (Except ALL CLIPS and ALL PLAYLISTS).
For example in [Picture 6.20] , it selected DARIM.
In order to command NAME, use , button as it is shown in the [Picture 6.20],
move to NAMElocation
If NAMEcommand is selected, DARIM there will be a square location where you can
edit. Use , utton to move each characters to change of the NAME. Please
move to the characters you want to change, as it is shown in picture [Picture 6.20] D.
Press SELECT button to execute selected NAMEcommand from the Play-List.
8/10/2019 B DVR UserGuide2
67/95
B-DVR MENU
B-DVR Users Guide 59
[Picture 6.21] Displaying for Changing the Name
If NAMEcommand is executed, Play-List Menu will appear with selection of characters,
as shown in [Picture 6.21]. Use , buttons and , buttons to select characters
or numbers.
To finish press SELECT utton.
The new characters or numbers will appear in the Play-List Menu.
8/10/2019 B DVR UserGuide2
68/95
8/10/2019 B DVR UserGuide2
69/95
B-DVR MENU
B-DVR Users Guide 61
[Picture 6.23] Clear Content Display
If CLEAR command executed, the confirmation question will pop up in the Play-List
Menu as it is shown in [Picture 6.23] . Use , button to select to cancel CLEAR
by selecting NO, to continue CLEAR, select YES.
Press SELECT button after confirmation.
If CLEAR command is executed, the Clip will be cleared from the Play-List and
PLAYLIST # clip names will appear.
8/10/2019 B DVR UserGuide2
70/95
B-DVR MENU
B-DVR Users Guide62
6.14 Managing Clip-List
In Play-List Menu, Clip Menu is included to manage the information of the Clip. All the
Clips which are included in the Clip-List can be inserted by using RECORD button to make
MPEG-2 file or copy MPEG-2 file into B-DVR Hard Disk through B-DVR Desktop program.You can view Clip-List, from Play-List Menu by selecting CLIP.
In the Clip-List Menu, there are 4 different commands.
PLAY : Play the selected Clip.
NAME : Name the selected Clip.
DEL : Delete the selected Clip.
DELALL : Delete Every Clips
[Picture 6.24] Clip-List Menu Display
6.14.1 Overall Execute Summary
Press LIST button to have Play-List Menu.
Use , button and select the CLIPand press SELECT button as it appears in Clip-
List Menu in [Picture 6.24].
To get out of Clip-List Menu, Press LIST button once to go to Play-List Menu. To get out
of Play-List menu, Press LIST button once more.
8/10/2019 B DVR UserGuide2
71/95
B-DVR MENU
B-DVR Users Guide 63
6.15 Play Clip-List Items
You can make up to 300 different items in Clip-List Menu. You can execute PLAY,
NAME, DEL, DELALL for every item in Clip-List.
[Picture 6.25] Select PLAY in CLIP-LIST.
In addition, for all the items, if one item is selected, the date and the size of the Clip can be seen
on the display. In [Picture 6.25], it is displaying that the item was recorded on June 26h, 2003
and 21Mbytes data are being used.
6.15.1 PLAY Command
Press LIST button to go to Play-List Menu.
Use , button to place CLIPcommand.
Press SELECT button to go to Clip-List Menu.
In Clip-List Menu, use , utton to select the item to give PLAYcommand from
00 ~ 99. For example, in [Picture 6.25] FASHIONM10 is selected.
To play use , button to move to PLAY like in [Picture 6.25].
Press SELECT button to PLAYthe selected Clip.
When PLAYexecuted, Clip-List Menu automatically disappear and selected Clip is ready
to play from start from the beginning of the clip from the pause mode.
Press PLAY button to play the video
8/10/2019 B DVR UserGuide2
72/95
B-DVR MENU
B-DVR Users Guide64
6.16 Change the names of the Clip-List items
It is possible to change the names of the saved items from the Clip-List. Maximum of 12
characters can be used including alphabets and numbers.
[Picture 6.26] Change the names of the Clip-List items
6.16.1 NAME Command
Press LIST button to go to Play-List Menu.
Use , button to place CLIPcommand.
Press SELECT button to go to Clip-List Menu.
In Clip-List Menu, use , utton to select the item to give PLAYcommand from
00 ~ 99. For Example, in [Picture 6.26] FASHIONM10 is selected.
To select NAME, use , button as [Picture 6.26] to place NAME.
When cursor is placed on NAME, editing box will appear for you to change the names as
shown in the [Picture 6.26], 0217_155602. Use , button to move to each
different characters. Move to the character you wish to change. For example, in [Picture
6.26] 0 is selected.
Press SELECT button to place the name that had created in the Play-List.
8/10/2019 B DVR UserGuide2
73/95
B-DVR MENU
B-DVR Users Guide 65
[Picture 6.27] Display for changing the names
If NAME command is executed, selected characters are displayed in Clip-List Menu to
choose (Refer to [Picture 6.27]). Use , button and , button to characters
or numbers which you wish to change.
After finishing press SELECT button.
The newly changed characters or numbers will be appeared in the Clip-List Menu.
8/10/2019 B DVR UserGuide2
74/95
B-DVR MENU
B-DVR Users Guide66
6.17 Delete Clip-List Items
It is easy to delete the saved clips from the Clip-List. There are two commands for deleting
Clip-List Items, DEL command is to delete only selected items from the Clip-List, and
DELALL is to delete all clips in Clip-List in B-DVR. These two commands delete theclips from the hard disk, so any important or necessary clips are always suggested to back
up to PC hard disk using B-DVR Desktop program. Once it is deleted, the clips can
never be restored.
[Picture 6.28] Display for deleting from the clip items from the Clip-List
6.17.1 DEL(Delete), DELALL(Delete All) Command
Press LIST button to go to Play-List Menu.
Use , button to place CLIPcommand
In Clip-List Menu, use , button to select the item to give DEL or DELALL
command from 00~99. For example, in [Picture 6.28] 0217_155602is selected.
To DELor DELALL use , button to move to DELor DELALL like in [Picture
6.28].
Press SELECT button to delete for DELfor selected Clip and DELALLfor deleting all
clips.
8/10/2019 B DVR UserGuide2
75/95
B-DVR MENU
B-DVR Users Guide 67
[Picture 6.29] Display for Deleting Clip
If DELor DELALLcommand has executed, the confirmation question will pop up in the
Play-List Menu as it is shown in [Picture 6.29]. Use , button to select to
cancel DEL or DELALL by selecting NO, to continue DEL or DELALL, select
YES
Warning : All deleted clips CANNOT be restored.
Press SELECT button to finish.
DELor DELALLcommand is executed Clips from the Clip-List are deleted.
8/10/2019 B DVR UserGuide2
76/95
B-DVR MENU
B-DVR Users Guide68
8/10/2019 B DVR UserGuide2
77/95
B-DVR Users Guide 69
7 B-DVR DESKTOP SOFTWARE
Darim is providing with B-DVR Desktop software to install in P.C. You must install this software to
use MPEG 2 file that had been recorded and played from B-DVR in your PC. The Hard Disk that
had been recorded and played in B-DVR s set as MASTERmode so before connecting to the PC,check the jumper setting in IDE mode. Default is set as either MASTER or SLAVE mode.
Depending on how IDE is stored in PCs select appropriate mode, MASTER or SLAVE.
You cannot use the file more than 4GB in FAT16 and FAT32 Operating system in Microsoft PC. In
addition, it is optimized play in over 4GB file supported NTFS format Hard Disk in Windows 2000 or
Windows NT.
Every MPEG-2 file saved into the Hard Disk in B-DVR can be copied into PC using B-DVR Desktop
software and MPEG 2 file saved into PC can be copied into B-DVR hard Disk. When B-DVR
Desktop software is used, MPEG-2 file from B-DVR Hard Disk can be played in PC and you can edit
and manage the Play-List and Clip-List in your PC.
The advantage of using Hard Disk of B-DVR is that any Clip that has been deleted appeared as free
space to optimize the function of Hard Disk. You can add Clip in your PC using B-DVR Desktop
software for any MPEG-2 file. However, in some occasions, some of the clips which had not been
recorded nor added through B-DVR but in PC using B-DVR Desktop software, PLAY or Mark In/Out
would not be able to function in B-DVR.
8/10/2019 B DVR UserGuide2
78/95
B-DVR DESKTOP SOFTWARE
B-DVR Users Guide70
7.1 B-DVR Desktop Software
In order to install B-DVR Desktop software which is included in B-DVR package, run the B-
DVR Desktop.exe then it starts to install.
[Picture 7.1] B DVR Desktop S/W Installation
It is possible to access to the B-DVR Hard Disk on PC via B-DVR Desktop when you
finish the installation B-DVR Desktop software.
After switching off power, make sure that the Hard Disks jumper setting in order not to
collide with other IDE device as the B-DVR Hard Disk is in set up in MASTER.
Although Hard Disk doesnt appear on the Windows Explore, it must be recognized inCMOS Setup.
In general, run Start ProgramB-DVR DesktopB-DVR Desktop, then B-DVR
Desktop software is run.
There are 2 items in B-DVR Desktop S/W, which are Play-List and Optimization.
8/10/2019 B DVR UserGuide2
79/95
B-DVR DESKTOP SOFTWARE
B-DVR Users Guide 71
7.2 Clip-List Menu
These are the Clip-List menu which have functions like PLAY, NAME, DEL in B-DVR ( Refer
6.14 ).
[Picture 7.2] Clip-List Menu
Save Clip to Local HDD Save the selected Clip of B-DVR Hard Disk to PC
Hard Disk as *.mpg(MPEG-2) file.
It can be saved by double click the selected Clip.
Rename Change the name of selected Clip.
Delete Clip Delete the selected Clip.
Delete All Clips Delete the all Clip.Play Play the selected Clip.
Add Clip to B-DVR HDD Add *.mpg(MPEG-2) file in PC Hard Disk to B-
DVR Hard Disk. It can be added by dragging a file
with a mouse.
8/10/2019 B DVR UserGuide2
80/95
B-DVR DESKTOP SOFTWARE
B-DVR Users Guide72
7.2.1 Marking and Play a Clip on B-DVR HDD with MPEG- Viewer
[Picture 7.3] MPEG2 Viewer
Mark In Indicate the starting part.
Mark Out Indicate the ending part.
Crop Operate Marking.
Snap Shot Save the selected picture of B-DVR Hard Disk to PC
Hard Disk as *.bmp(BMP) or *.jpg(JPEG) file.Play Play the selected Clip.
Stop Stop the played Clip.
Close MPEG2 Viewer Close the MPEG2 Viewer window.
8/10/2019 B DVR UserGuide2
81/95
B-DVR DESKTOP SOFTWARE
B-DVR Users Guide 73
7.3 Play-List Menu
These are Play-List menu which have functions like EDIT, NAME, CLEAR.
[Picture 7.4] Play-List Menu
Rename Change the name of Play-List.
Delete Play-List Delete Play-List.
Save Clips to Local HDD Save Clips in the selected Play-List of B-DVR Hard
Disk to PC Hard Disk as *.mpg(MPEG-2) file.
8/10/2019 B DVR UserGuide2
82/95
B-DVR DESKTOP SOFTWARE
B-DVR Users Guide74
7.4 B-DVR Hard Disk Optimization
The optimization is in Item.
Press icon, then you can move to the window for optimization of Hard Disk.
Press icon to go back to Play-List.
[Picture 7.5] Optimization
The space of deleted clips may be remained as occupied in the Hard Disk. B-DVR uses the
data in order and only has the information of deleting of Clip. You must optimize to use
Hard Disk effectively.
8/10/2019 B DVR UserGuide2
83/95
8/10/2019 B DVR UserGuide2
84/95
B-DVR DESKTOP SOFTWARE
B-DVR Users Guide76
[Picture 7.7] B-DVR Settings
7.5.2 Scheduler
When Scheduler icon is selected, the following dialogue will be shown.
8/10/2019 B DVR UserGuide2
85/95
B-DVR DESKTOP SOFTWARE
B-DVR Users Guide 77
[Picture 7.8] Scheduler
[Picture 7.9] Schedule Setting
The user can setup the menus including the Mode, Starting Time, Ending Time, Play list/Bitrate
8/10/2019 B DVR UserGuide2
86/95
B-DVR DESKTOP SOFTWARE
B-DVR Users Guide78
by double-click of desired item as shown in the [Picture 7.9]
[Picture 7.10] Scheduler Menu
Clear Selected Schedule Deletes the selected schedule
Clear Schedule From Selected Deletes the schedule list from the selected one to the
last one.
Clear All Schedule Deletes all schedule list
Delete Same as Clear Selected Schedule Menu
Save To File Saves the schedule list as a file.
Load From File Load the schedule list from a schedule file which ispreviously saved.
OK Applies the setting value of schedule
Cancel Exits from the dialog box without applying new
setting value of schedules
8/10/2019 B DVR UserGuide2
87/95
B-DVR Users Guide 79
8 HARD DISK MANAGEMENT AND HOW TO USE
8.1 B-DVR Hard Disk Jumper Setting
The Hard Disk can be used in B-DVR is one of most general IDE type hard disk.The general IDE Type hard disk doesnt need any special format or changing to file
system to use easily by inserting to Hard Disk rack. Make sure that the jumper
setting of Hard Disk must be setup in Master mode among Master/Slave modes. If
it is in Slave mode or jumper setting is not right, the message Err 01 is displayed in
the VFD of front panel when switching on power of system.
8.2 How to use B-DVR HDD on general PC
Make sure that you use Software provided by Darim Vision Co. Ltd. in order to use
B-DVR HDD in general PC. If not, all the information of HDD can be deleted.
The HDD used in general PC can be used in B-DVR right away by installing it toHDD rack in MASTER mode setup.
8/10/2019 B DVR UserGuide2
88/95
HARD DISK MANAGEMENT AND HOW TO USE
B-DVR Users Guide80
8/10/2019 B DVR UserGuide2
89/95
B-DVR Users Guide 81
9 TROUBLESHOOTING
B-DVR, a MPEG-2 capture device is run by separate S/W with no related with Windows and it
is designed not to collide with other device if possible. Most troubles can be occurred when
unskilled operation or unbalanced situation of system is run.
9.1 How to solve the trouble of B-DVR
How to solve that video Clip of B-DVR is not displayed
The trouble happens when setting up hardware and Menu of B-DVR. B-DVR Video Input
supports 2 types such as Composite and S-Video and Video Output supports 4 types such as
Composite, S-Video, RGB and Component.
Make sure to set up Video Input and Video Output properly in Video Set up Main Menu.
When new Hard Disk is connected to B-DVR, Video Input supports Composite and Video
Output supports S- ideo(Composite). Refer to 6.4 Video Setup.
How to solve that Playlist of B-DVR is not displayed
Make sure that clips are set up in the Play-List item in the List menu. If the Clip is not
inserted in Play-List, that Play-List can be played.
How to recover the deleted Clip in Play-List
The Clips in HDD are not deleted really although it is deleted from the Play-List. But the
Clips deleted on the Clip-List can not be recovered as it is deleted from the HDD.
Therefore note that you must be careful to delete Clip on the Clip-List.
How to do when the HDD used in B-DVR can not be used in PC
Make sure that you change the jumper(Refer to HDD information) of HDD type to Slave
mode when you want to use B-DVR HDD in general PC. The OS(Operating System) of
B-DVR is different from the OS of general Windows or Dos, so B-DVR HDD itself is not
booted in general PC. You must use the S/W provided by Darim Vision Co. Ltd. in order
to use B-DVR HDD in general PC.
You can use the HDD used in general PC in the B-DVR by installing hard rack. Darim
Vision is not responsible for the damage of HDD caused by customers fault. You must
inquire to the dept. of customer support of Darim Vision Co. Ltd. about the change of HDD.
When the recording time is over 13 hours
8/10/2019 B DVR UserGuide2
90/95
TROUBLESHOOTING
B-DVR Users Guide82
The present B-DVR decides the recording time of one Clip depending on the remaining
space of HDD. It is possible to record for a long time if the space of HDD is enough. But
do not try to record one Clip for over 13 hours. When you play the Clip recorded for over
13 hours, the displayed time in VFD of front panel is initialized to 00:00:00 after the time of
13:14:34. It is caused by the trouble of MPEG-2 Encoder of B-DVR. Therefore it isdesigned to record for less 13 hours. Refer the messages in recording from [9.2 essage
occurred in B-DVR activation].
When the deleted Clip plays All Clips in playback mode
You can PLAY, NAME, DEL and ALLDEL all Clips in Clip-List. If you record at the
latest or add MPEG-2 file using B-DVR Desktop software, it is located in the closest to
Clip-List No.00. The Clip of the last no is the recorded Clip at the first time. Though
it is deleted once, it can be appeared in the Play-List by selecting All Clips to playback.
It is suggested to optimize using B-DVR Desktop.
How to do when less storage space in HDD
B-DVR saves Clips in order when recording or adding Clips using B-DVR Desktop.
Therefore, it can be happened to have less remaining space of HDD than calculated from the
whole space.
In order to use Hard Disk effectively, it is suggested to optimize HDD by connecting to PC
and using B-DVR Desktop
In case there is incorrect Time-Code in front VFD panel
For Users friendly, when playing or recording MPEG-2 file in B-DVR, Time-Code
indicates in VFD. Any information related in Time-Code in current used MPEG-2 file in
B-DVR includes maximum about 13 hours. There are 2 cases of initialization of Time-Code
of B-DVR. When user records and playback over 13 hours, the value of Time-Code
converts to the initialized value. Another case, it happens in pause even though userrecorded under 13 hours. According to these phenomena, the real recording time cannot
be same with the Time-Code in VFD. It is caused by the inaccurate calculation of Time-
Code information in MPEG-2 file and cannot be fixed under the existing system.
However, the related Time-Code information in VFD supports to search image and
find the general location. User can use this Time-Code information for Mark In/Out
and simple reference.
8/10/2019 B DVR UserGuide2
91/95
TROUBLESHOOTING
B-DVR Users Guide 83
9.2 Messages occurred B-DVR activation
When switching on B-DVR
message symptom solution
Rec:LoadClip error Cannot read Information from HDD Make sure HDD jumper is in MASTERmode and reboot B-DVR again. The
same symptom is occurred again, set up
HDD in Low Level Format. Needs A/S
of HDD when still having problem.
Please, backup clips HDD is not compatible with older B-
DVRs HDD.
Clips were made in older B-DVR, HDD
is not compatible with used before.
Please save clips by using B-DVR
desktop software then make all clips in
B-DVR HDD to use properly.
When pressing Menu button
Config save error!!!
Config read error!!!
Cannot read or save Information
from HDD
Make sure HDD jumper is in MASTER
mode and reboot B-DVR again. The
same symptom is occurred again, set up
HDD in Low Level Format. Needs A/S
of HDD when still having problem.
Messages in palying
No MPEG Clips No saved MPEG-2 video clip in HDD
Ready Being ready for playing MPEG-2 video
clip
"Begin ing of clip" Located in the beginning position of
MPEG-2 video clip
"End of clip" Located in the last position of MPEG-2
ideo clip
"Forced Stop" Play mode is forced to stop due to error
of B-DVR
Messages in recording
"End of HDD" Full of MPEG-2 video clips in HDD
Reached max-time of Stop recording due to over 13 hours
8/10/2019 B DVR UserGuide2
92/95
TROUBLESHOOTING
B-DVR Users Guide84
a clip recording.
"Reached max. number
of clips "
100 MPEG-2 video clips in HDD
"File Writing Error!!!"
"Writing error""File System error"
Error in HDD. Make sure HDD jumper is in MASTER
mode and reboot B-DVR again. Thesame symptom is occurred again, set up
HDD in Low Level Format. Needs A/S
of HDD when still having problem
"Recording error" Error in Streaming board. Reboot B-DVR and record. Ask the
nearest dealer when still having
problem.
"No input signal" Try to recording without Video In Connect camera to Video In and
confirm the power.
"Failed to save clip Cannot recording 1) Error in HDD
Make sure HDD jumper is in MASTER
mode and reboot B-DVR again. The
same symptom is occurred again, set up
HDD in Low Level Format. Needs A/S
of HDD when still having problem
2) No Video In.
3) Recording Time is less than 1
second.
4) Over 100 clips or HDD is full.
Messages in BookMark
"Failed to save
bookmark"
Can not save the information of
BookMark.
Press Stop utton to finish Play and
ookmark again in the same position.
"Bookmark doesnt
exist"
BookMark does not exist.
"IsBooked read error"
"GetAllBookMarkClip
read error"
Failed to read the information of
BookMark in HDD.
Messages in Mark In/Out
"Marking failed" Failed Marking. Press Stop utton to finish Play mode
and mark again in the same position of
8/10/2019 B DVR UserGuide2
93/95
TROUBLESHOOTING
B-DVR Users Guide 85
marking.
8/10/2019 B DVR UserGuide2
94/95
8/10/2019 B DVR UserGuide2
95/95
TROUBLESHOOTING
Note) he improvement of design and specification can be changed as upgraded without
rior notification.