Audio-Visual Solutions

HDMI Installation TrainingAnalog to Digital, simple to sophisticated, all from one source!

Who is Intelix?

Founded in 1986Based in Middleton, WI USAEngineering heritageHistorically Pro-AudioToday 90% Video

Who is Intelix? Market SegmentsPro AV

Residential CI

DataComSecurity-CCTV

Product Categories

HDMI SystemsDigital Signage SystemsPassive and Active Twisted Pair Extension SolutionsSecurity Distribution ProductsAudio Matrix SystemsRoom Combine SystemsPaging Systems

Who is Intelix?

Before we start…The most current Installation Manuals and Software are located at:www.intelix.com under “Technical Library”

HDMI Product Installation

Installing the DIGI-HD-UHR2 and DIGI-HD-IR2

1080p 1080i 720p 480i/p

Cat 6 (low-skew)

150’ 300’ 300’ 350’

Cat 6 110’ 220’ 220’ 220’

Cat 5e 100’ 200’ 200’ 200’

1080p 1080i 720p 480i/p

Cat 6 (shielded)

150’ 300’ 300’ 350’

Cat 6 110’ 220’ 220’ 220’

Cat 5e 100’ 200’ 200’ 200’

Installation Considerations

Installing the UTP Extenders

Use the EIA/TIA 568B Crimp PatternPower is required on send and receive extendersThird-party IR systems are not compatible with the DIGI-HD-IR2

(Intelix is a 5V system)The extenders will feel warm (98 degrees F)Do not connect the balun to a telecommunication outlet wired to

unrelated equipment. Ensure all connected twisted pair cabling is straight-through

(point-to-point)

Instructions Power off all AV equipment Make sure you have a point-to-point circuit. Make sure source and display work with HDMI cable Test the HDMI patch cables

Instructions Connect the DIGI-HD-UHR2 transmitter to the source then the

receiver to the display (no power) Connect the CAT cable

Instructions Power on the receiver then transmitter Power on the source and display devices Verify picture quality

Copying EDID - DIGI-HD-UHR2

Disconnect the transmitter and receiverConnect transmitter to display with HDMI cable

Copying EDID - DIGI-HD-UHR2

Press “Hand Shake” button LEDs will flash and then remain solidEDID is copied Disconnect transmitter and repeat normal

installation

Bandwidth Shaping DIGI-HR-UHR2

Position 1 Position 2 Mode

Off Off Use copied EDID data from displayOff On Turn on Dolby TrueHD and DTS-HDOn Off Turn on stereo audioOn On No function

Transmitter DIP Switch Positions

Unplug all of the cables to make DIP switch changesChange the DIP switch position Reconnect the transmitter

The UHR2 will not pass EDID information from the display to the source

Bandwidth Shaping DIGI-HR-IR2

Position 1 Position 2 Mode

Off Off Read EDID data from displaysOff On Turn on Dolby TrueHD and DTS-HDOn Off Turn on stereo audioOn On No function

Transmitter DIP Switch Positions

Unplug all of the cables to make DIP switch changesChange the DIP switch position Reconnect the transmitter

The IR2 will pass EDID information from the display to the source.

Using IR with the DIGI-HD-IR2Disconnect power from BalunsAttach emitter to source and eye to display

Plug the emitter into send side of DIGI-HD-IR2Plug the eye into the receive side of DIGI-HD-IR2

Using IR with the DIGI-HD-IR2

Power the extenders and test IR

Installing the DIGI-HD-COAX-S and the DIGI-HD-COAX-R

1080p 1080i 720p

RG6 300’ 675’ 675’

RG59 250’ 675’ 675’

• Will only run at 3 resolutions• 720p-60• 1080i-30• 1080p-60

• DVI will only work at the available resolutions• Source equipment will need to be forced into available

resolutions• No taps, splitters, amps, pads or filters• Works with barrels or F-connectors• Needs a minimum of 50’ of 75 Ohm cable• Does not pass 3D

Installing the DIGI-COAX

Instructions Power off all AV equipment Make sure you have a point-to-point circuit. No taps, splitters, amps, pads or filters Works with barrels or f-connectors

Instructions Connect the transmitter to the source

then the receiver to the display (no power)

Connect the COAX cable to the “A” side of the transmitter (BNC or F-connector)

Connect the Coax to the “input” on the receiver

Instructions Power on the receiver then transmitter Power on the source and display devices Verify picture quality

HDMI Digital Signage Application

Installing the DIGI-SCAL-11x2

Switcher/Format Converter/Scaler

DIGI-SCAL-11x2

• HDMI outputs are mirrored not matrixed• 3 to 5 second switch time• Video blue screen during switch process• Volume cannot be changed• It will not convert audio from digital or analog stereo to multi

channel digital audio• It will only convert analog stereo audio to PCM digital stereo

audio and back.

Installation Instructions

Attach the feet or the rack ears depending on how the unit will be mounted. (The DIGI-SCAL-11X2 requires one rack unit of spacing.)

Power off source and destination devicesConnect input sources Connect output destination(s)

Connect power supply Connect RS232 or IR if the unit is remote controlled Power on DIGI-SCAL-11x2 Power on source and designation devices

Operation – Channel Pairing

• Audio and Video pairing are as follows:

Input Video Format Audio Format1 Compsite Stereo Audio2 Compsite Stereo Audio3 YPbPr Stereo Audio4 YPbPr Stereo Audio5 VGA Stereo Audio6 S-Video Stereo Audio7 DVI-I Stereo Audio & Digital audio8 HDMI Digital audio9 HDMI Digital audio10 HDMI Digital audio

Operation – Channel Pairing

• VGA Audio

• S-video Audio

• DVI-I

Built-in Audio Conversion and Embedding

Analog Stereo Audio In

Analog Audio Out

PCM Digital Audio Out

PCM Digital Audio In

PCM Digital Audio OutAnalog Audio Out

PCM Digital Audio Out

Operation – Front Control Panel

• Power on the unit by selecting the Standby button.• Select the input with the rotary knob.• Select output resolution with the Mode Selection button.

Operation – Supported Signal Formats

Input Signal Format

Composite PAL, NTSC

S-video PAL, NTSC

YPbPr 480i, 480p, 576i, 576p, 720p, 1080i, 1080p

VGA 800x600, 1024x768, 1152x864, 1280x768, 1280x960,1280x1024, 1440x900, 1400x1050, 1600x1200, 1920x1200

DVI-I 800x600, 1024x768, 1152x864, 1280x768, 1280x960,1280x1024, 1440x900, 1400x1050, 1600x1200, 1920x1200

HDMI 480i, 480p, 576i, 576p, 720p, 1080i, 1080p

Output Signal Format

HDMI 720p, 1080p

Operation – Included Remote Control

Function DescriptionA Standby Toggles on and off standby mode (low power mode)B Source Selection Directly selects an audio-visual inputC Menu Toggles the onscreen menuD Info Toggles the input and output messagingE Source Scrolling Toggles the next or previous audio-visual inputF PC Bypass Toggles on and off PC bypass modeG 720p Mode Toggles the output mode to 720pH 1080p Mode Toggles the output mode to 1080p

Operation – PC Bypass Mode• PC Bypass Mode allows a computer’s native resolution to display on the destination monitor.• When using PC Bypass Mode, the front panel indicators will disable. In addition, the default

output will be in 1080p.• PC Bypass mode will only function when a VGA or DVI signal is present and my be activated

from the remote control or the “Mode Selection” button.

Input 800x600, 1024x768, 1152x864, 1280x720, 1280x960,1280x1024, 1440x900, 1600x1200, 1920x1080Output 800x600, 1024x768, 1152x864, 1280x720, 1280x960,1280x1024, 1440x900, 1600x1200, 1920x1081

PC Bypass Supported Resolutions

Operation – On Screen Display

Operation – RS232 Remote Control• The manual has a complete list of the RS232 control codes• Connect a straight-through serial cable directly to the matrix

9600 baud rate8 data bits1 stop bitNo parity bitNo handshake

Installing the DIGI-HD-4X4 and 4X2

DIGI-HD-4X4

Installing the DIGI-HD-4X4

Installation Considerations• “A” and “B” RJ45 jacks on the output will only connect to one

DIGI-HD-UHR2-R or DIGI-HD-IR2-R • You can mix DIGI-HD-UHR2-R or DIGI-HD-IR2-R• Consider buying and extra DIGI-HD-UHR2-S to make copying

EDID from the displays easier.

Installing the DIGI-HD-4X4 and 4X2

Attach the feet or the rack ears depending on how the unit will be mounted. (The DIGI-HD-4X4 requires one rack unit of spacing.)

Power off source and destination devicesConnect input sources Connect output destination to HDMI or twisted pair

Installation InstructionsRecommended Twisted Pair Receivers

1080p 1080i 720p 480i/p

Cat 6 (shielded)

150’ 300’ 300’ 350’

Cat 6 110’ 220’ 220’ 220’

Cat 5e 100’ 200’ 200’ 200’

Twisted Pair Settings-Toggle all Ports1. To toggle between single and dual twisted pair modes,

simultaneously press and hold the Output 3 button and Key-lock button for 3 seconds.

2. Use Output 1 and Output 2 and Key-lock to toggle the DIGI-HD-4X2 3. The default setting of the DIGI-HD-4X4 is double twisted pair mode.

Twisted Pair Settings-Using ComCtl software

Signal Mode Settings set by DIP switches: HDshāk Inside

EDID CopyBandwidth Shaping

DIP Switch Mode SettingsDIP 1 DIP 2 DIP 3 EDID Function

off off off Dual Twisted Pair Mix ModeThe matrix mixes the EDID data of all destinationswhich choosing the same source. This data is thentransmitted by the matrix to the source device. Tocopy and sync the EDID data, simultaneously pressand hold the Output 1 button and Keylock buttonfor 3 seconds.off off on EDID Copy ModeEDID data is copied from the selected output andtransmitted to the desired input. To copy and syncthe EDID data, press and hold the output button ofthe selected output for 3 seconds.

off on off Factory Default: 1080p with stereo audioThe matrix is preset with EDID data for 1080pvideo and stereo audio.

off on on Factory Default: 1080i with stereo audioThe matrix is preset with EDID data for 1080i videoand stereo audio.

on off off Factory Default: 1080p with 5.1 audioThe matrix is preset with EDID data for 1080pvideo and 5.1 audio.

on off on Factory Default: 1080p with 7.1 audioThe matrix is preset with EDID data for 1080pvideo and 7.1 audio.

Connect the included 12 VDC power supply to the DIGI-HD-4x4.

If controlling remotely, connect RS232, Ethernet, or IR control cables.

Power-on the DIGI-HD-4x4. Power-on the source and destination audio and

video devices. Power off DIGI-HD-4X4 before changing the DIP

switches to change signal mode. Power up to have changes take effect.

Operation

Front Panel Control Basics

Operation• Included Remote Control

Operation - SetupIR Remote Control

Operation - SetupRS232 and Ethernet Remote Control

Web Control

DHCP or Static IP address

DIGI-HD-8X8

Installation Considerations• “A” and “B” RJ45 jacks on the output will only connect to one

DIGI-HD-UHR2-R or DIGI-HD-IR2-R • Use only DIGI-HD-UHR2-R or DIGI-HD-IR2-R for all 8 extension

out puts. Do not mix.• Consider buying and extra DIGI-HD-UHR2-S to make copying

EDID from the displays easier.

Attach the feet or the rack ears depending on how the unit will be mounted. (The DIGI-HD-8X8 requires four rack units of spacing.)

Power off source and destination devicesConnect input sources Connect output destination to HDMI or twisted pair

Installation InstructionsRecommended Twisted Pair Receivers

1080p 1080i 720p 480i/p

Cat 6 (shielded)

150’ 300’ 300’ 350’

Cat 6 110’ 220’ 220’ 220’

Cat 5e 100’ 200’ 200’ 200’

Signal Mode Settings set by DIP switches: HDshāk Inside

Single or Dual EDID CopyBandwidth Shaping

DIP Switch Mode Settings

With DIGI-HR-UHR2-R

Example setup:Inputs (3) Satellite boxes (1) DVD PlayerOutputs (2) Local TVs (2) Remote TVs

Example setup:Inputs (3) Satellite boxes (1) DVD PlayerOutputs (2) Local TVs (1) Remote TVs with IR remote

With DIGI-HR-IR2-R

Connect the included 12 VDC power supply to the DIGI-HD-8X8.

If controlling remotely, connect RS232, Ethernet, or IR control cables.

Power-on the DIGI-HD-8X8. Power-on the source and destination audio and

video devices. Power off DIGI-HD-8X8 before changing the DIP

switches to change signal mode. Power up to have changes take effect.

Operation

Front Panel Control Basics

Default PasswordsUser: 1234Admin: HDMI

Operation

Selection using “Room View”

Operation

Selection using “Matrix View”

OperationSelect a “Preset”

OperationSet a new “Preset”

Operation – User access Lock Screen

Unlock Screen

Operation - SetupOpening the “Utilities” menu as administrator

Operation - SetupSet User and Admin passwords

Operation - SetupDefine Input Icons

Operation - SetupDefine Input Text Label

Operation - SetupCopy EDID when using DIGI-HD-UHR2-R receivers

Operation - SetupDefine Output Icons

Operation - SetupDefine Output Text Label

Operation - Setup

Reset System Settings

Operation - Setup

Included Remote Control• Directly with Matrix

– Buttons 1 to 8 are destinations– Arrows are “previous” and “next” source

• Through Extender– Extender location defines output– Buttons 1 to 8 represent inputs– Discretely choose inputs

Operation - SetupIR Remote Control

Extend the IR sensor with the included “eye” -Plug it directly into the 3.5mm jack in the

back of the unit-Third-party IR devices are not

compatible with the 3.5mm jack

Using third-party IR control-Connect from base IR control unit using

Ethernet or RS232-IR control – attached emitter to IR pickup

on the front for the unit

Operation - Setup

RS232 Remote Control

• RS232 programming and command information is Appendix A of the manual• Must receive all messages in hexadecimal number code.• If messages are transmitted in decimal or ASCII codes, they will fail to work.

Operation - Setup

Ethernet Remote Control• Connect an Ethernet cable directly to the matrix. • The DIGI-HD-8X8 will automatically be assigned an IP address when connected to a

DHCP-enabled network. By default, DHCP is enabled.• Within 10 seconds of connecting the DIGI-HD-8X8 to the LAN, the yellow LED on the

matrix’s Ethernet port will stop blinking and the green LED will blink intermittently.• For Ethernet programming and command information, see Appendix A

Operation - Setup

Web Control

Operation - Setup

IR Twisted Pair Pass-Through Determine which devices you wish to control via the IR pass-through outputs. Connect an IR emitter to the desired IR transmit output port. Repeat for up to eight devices. All of the remote receive baluns transmit IR commands from the included remote

control, thereby allowing remote control of the matrix itself. Verify that IR pass-through is enabled in the front panel LCD Utilities screen.

Why Intelix?

Maximize Performance:Complete integrated solution approach

Why Intelix?

Insured Reliability:Multi Stage Quality Assurance Process

Less than a 1% return rate

Why Intelix?

World Class Support:Pre and post sales technical

and applications support90 day advanced replacement2 year warranty on all products

Intelix ContactsTechnical Sales /Training: Brad Weisbrod | bradw@intelix.comOrder Status: Ellen Domine | ellend@intelix.comPricing Inquiries: Beth Green | bethg@intelix.comTechnical Support: Sterling Glass | sterlingg@intelix.comMarketing Inquiries: Eric Lang | ericl@intelix.com

Domestic Sales Questions: Cameron Smith | camerons@intelix.com

International Sales Questions: Steve Cohan | stevec@intelix.com

608-831-0880 phone | 608-831-1833 fax | www.intelix.com

Intelix

Resources

608-831-0880 phone | 608-831-1833 fax | www.intelix.com

Intelix

Literature Library: http://www.intelix.com/tech_library/marketing_lit.aspx

Product Technical Literature: http://www.intelix.com/tech_library.htm

Audio-Visual Solutions

Documents

Transcript of Audio-Visual Solutions

nevayacast. - Lumino AV | Audio and Visual Solutions | UK

AUDIO & VISUAL

Audio-Visual, Staging, and Seating Requestskathleenpassanisi.com/files/Audiovisual_staging.pdf · Audio-Visual, Staging, and Seating Requests ... Good audio-visual equipment and a

Audio Visual Solutions for Business

AUDIO / VISUAL – AUDIO AND VISUAL SYSTEM AV–1 AUDIO AND ...

Audio VisuAl solutions for diGitAl siGnAGE APPliCAtions€¦ · Audio VisuAl solutions for diGitAl siGnAGE APPliCAtions digital signage Collection. 2 UNPARALLELED PEOPLE, PROCESSES

Authentic Audio Visual Private Limited, New Delhi, Audio-Visual Security

Audio Visual System Solutions for Education… · SOLUTION GUIDE LECTURE HALLS Audio Visual System Solutions for Education

AUDIO-VISUAL · Audio Visual By Rickiell & Co. AVR is an Anguillian-based creative audio-visual services provider that specializes in producing audio and visual content for individuals

Professional Audio Visual Solutions - Home - Voitech Solutions

· 2014-04-06 · Audio-Visual Aids Technician I Audio-V'sual Alds Technician Il Audio-Visual Aids Technician Ill Audic-Visual Aids Techn.cian IV Audio-Visual Equipment Operator

Audio Visual - appliedelectronics.com · AUDiO VisUAL sOLUTiONs DiGiTAL siGNAGE sYsTEMs Creating vitality in any environment through the use of interactive digital displays. Incorporating

NEW ZEALAND ADVERTISING AUDIO VISUAL …apraamcos.co.nz/media/3561/nz_pmratecard2014_final.pdfnew zealand advertising audio visual gaming & mobile apps audio ... advertising audio

A Guide To Office Based Audio Visual Solutions

AGC’s Audio Visual Integration Solutions.

Flexible Professional Audio Solutions · acoustic engineering in flexible audio solutions for ... an Audio-Visual system playing back film ... 85mm diameter ceiling spotlight cut-out

AUDIO / VISUAL – AUDIO AND VISUAL SYSTEM AV–1 AUDIO AND ...static.hybrids.ru/files/OfficialToyotaInfo... · AUDIO / VISUAL – AUDIO AND VISUAL SYSTEM AV–7 AV • A disc may

Audio-Visual Solutions Digital Signage Solutions Discover Intelix, Discover Reliability!

Statewide Term Contract for Audio/Visual # 4400013021 ......Statewide Term Contract for Audio/Visual # 4400013021 BridgeTek Solutions, LLC. 110 Connector Park Ct Piedmont, SC 29673

Audio Visual System Solutions for Business