Post on 27-Mar-2021
www.amp-research.com 1/4 IM75413 rev 07.17.19
BedStep2™ is invented, designed, engineered and manufactured exclusively by AMP Research and may be covered by one of the following patents: 6,641,158; 6,830,257; 6,938,909; 7,055,839; 7,380,807; 7,398,985; 7,584,975. Made in USA © 2011 AMP Research Three-year limited warranty. Professional installation is recommended.
AMP RESEARCH TECH SUPPORT 1-888-983-2204 (Press 2) Monday - Friday, 7:00 AM - 5:00 PM PST
Ford Super Duty 2017 - 2021F-250/350 (Fits all Beds /Cabs)
1
6
5
4
2
3
14
8
9
12
11
13
APPLICATION
7
10
Driver-Side Orientation
Passenger-Side Orientation
Brackets must be configured for Passenger or Driver-Side as shown below:
15
16
�����
Torque wrench
13, 15, 22mm
AMP PART# 75413-01A
7/8”
T25 Torx
Assemble bracket as shown in the next three steps.Note: Driver side shown. Rotate frame spacer 180° for passenger side. (See image in step 1 for passenger orientation).
B. Install bracket to linkage, using supplied bolts (12). Hand tighten bolts then torque from steps A & B. See above for torque spec.
A. Install brackets (3 & 4) with bolts (8) and nuts (9), leave loose.
C. Attach frame spacer to assembled bracket using bolt (10) and spacer (16), hand tighten. See orientation from step 1.2
Swivel Joint
1/8” Drill Bit
11/32” Drill Bit
10” Extension
13mm Box Wrench
3” Extension
13mm torque extension
Torque bolts to 20 Ft-lbs.
Torque bolts to 16 Ft-lbs.
�����
13 & 15mm
3” Extension
13mmTorque wrench
1
www.amp-research.com 2/4 IM75413 rev 07.17.19
Locate mounting point under front bed mount bolt. Bracket assembly will slide over bed stud.
7/8, 22mm
Offset the step pad to the rear position of the lower linkage assembly and secure using provided PT Screws (13). Tighten to 5 Ft-lbs using T25 Torx bit.
T25 Torx
Adjust step pad to be in line with fender .
Snug Sleeve nut (11) with washer (15) to Bed Stud. Do not torque to allow for adjustment in next step. Note: Swivel joint may be necessary on short bed models if emergency brake cable bracket is in the way.
3
4
5
www.amp-research.com 3/4 IM75413 rev 07.17.19
13mm
13mm torque extension
�����
13mm Box Wrench
7/8, 22mm
Verify that step pad (2) is parallel to the bottom of the body line. A shim (14) is provided to level out step pad. See image for explanation.
Torque wrench
Swivel Joint
10” Extension
Torque wrench
7
6
8
Install forward support bracket (5) using supplied M8 hardware (8) bolts and (9) nuts. Torque bolts to 16 Ft-lbs.
Torque both the Sleeve nut (11) and bolt (10) to 30 Ft-lbs.
- Install Shim on right edge to increase the gap on the right side of step pad.
- Install Shim on left edge to increase the gap on the left side of step pad.
www.amp-research.com 4/4 IM75413 rev 07.17.19
To deploy the step, press down using your foot on the outside edge of the step pad.
To retract, gently kick up on the underside of the step pad.
Remove bracket and pre drill hole using a 1/8” drill bit then drill to 11/32”.
Install rearward support bracket (6) using supplied M8 Hardware(8) Bolts and (9) Nuts. Torque to 16 Ft-lbs.
1/8” Drill Bit
11/32” Drill Bit
9
1110
12
Attach rearward support bracket (6) using supplied M8 hardware (8) Bolts and (9) Nuts. Locate bracket as shown. Center punch hole using bracket as a guide as shown.
Thank you for your recent AMP Research Purchase.
REGISTER YOUR PRODUCT TODAY FOR FASTER SERVICE & PRODUCT UPDATES
Please visit: www.amp-research.com/productregistrationor scan the QR Code
Product Registration Benefits: • Ensure we have your purchase receipt and product info in our system which is required for warranty • Faster and easier access to customer service and tech support in the unlikely event you need warranty or product support • Registration helps us keep you up to date on product information and offers
To view other Amp Research products that may be offered for your vehicle. Please visit: www.amp-research.com
AMERICAN DESIGNED, ENGINEERED AND MANUFACTURED.
Rev 01.05.21