Post on 07-Jul-2018
8/18/2019 ALL STA COMPACT INSTALLATION UPDATE
1/24
Installation/update of online test setups
0931973B
Installation/mise à jour des méthodologies fournies par téléchargement
1/24
Installation/mise à jour des méthodologies fournies par
téléchargement
Historique
0931973 Première diffusion
0931973A Mise à jour suite à la nouvelle version du logiciel TSU. Document non diffusé.
0931973B Ajout d’étapes de vérification/impression/sauvegarde
L’installation et la mise à jour des méthodologies fournies par téléchargement s’effectuent au
moyen du logiciel Test Setup Updater (TSU dans la suite du document), version STB v0.01.01au minimum. Celui-ci est téléchargeable sous forme de fichier .zip. Son contenu devra être copié
sur un support, clé USB ou disquette, en vue de l’installation sur l’instrument. La clé USB sera
alors connectée au boîtier IMP. Voir le schéma ci-dessous.
Vue d’ensemble du transfert des données
Légende :
1 Téléchargement du fichier contenant le logiciel TSU et la MS
2 Téléchargement des BTS/BTA, le cas échéant
3 Décompression et mise sur le support
4 Installation sur l’instrument
20 min
8/18/2019 ALL STA COMPACT INSTALLATION UPDATE
2/24
2/24
Installation/update of online test setups
Installation/mise à jour des méthodologies fournies par téléchargement
0931973B
Etapes de la mise à jour
1. Préparation du support
2. Installation du logiciel TSU
3. Utilisation du logiciel TSU
3.1. Mise à jour de la base des méthodologies
3.2. Changement de conditionnement
3.3. Suppression de méthodologies
3.4. Réinitialisation de la base
3.5. Sortie
4. Définition ou vérification des paramètres des méthodologies
4.1. Pour une installation
4.2. Pour une mise à jour
5. Calibration des tests qui le nécessitent (après une mise à jour)
6. Impression des méthodologies du client
7. Sauvegarde de la nouvelle base de référence des méthodologies du client
Pré-requis
- Instrument version 108.05/208.05 a minima
- PC avec logiciel de compression de données, type Winzip, accès à un site Web Stago et port
USB ou lecteur de disquette
- Se procurer les dernières Procédures Opératoires Standardisées (uniquement pour les
méthodologies Stago)
- S’assurer qu’aucun test, contrôle ou calibration n’est en cours, sinon attendre que ces
opérations soient terminées.
- Décharger les tubes et flacons présents dans les tiroirs échantillons et produits.
- Se munir du code d’accès permettant de modifier les méthodologies
(voir le Manuel de référence, chapitre "Ecrans ETATS et OPTIONS GLOBALES", paragraphe
"Premier écran OPTIONS GLOBALES", sous-paragraphe "Description du premier écran
OPTIONS GLOBALES").
- Certaines opérations impliquent le remplacement des données de méthodologies existantes.
Veiller à toujours effectuer une sauvegarde avant d’effectuer cette procédure. (Voir le Manuel
de référence, chapitre "Maintenance", paragraphe "Utilitaire de maintenance", sous-paragraphe
"Sauvegarde".)
- Imprimer les méthodologies du client (voir paragrahe 6.Impression des méthodologies du
client)
- Imprimer les calibrations et les contrôles qualité pour toutes les méthodologies qui seront mises
à jour. Les calibrations et les contrôles qualité de ces méthodologies seront perdus.
Outils nécessaires
- Clé USB avec boîtier IMP ou disquettes vierges avec lecteur de disquette
8/18/2019 ALL STA COMPACT INSTALLATION UPDATE
3/24
Installation/update of online test setups
0931973B
Installation/mise à jour des méthodologies fournies par téléchargement
3/24
1. Préparation du support
Récupérer l’archive au format .zip contenant la dernière version du logiciel TSU.
Si le support choisi est une clé USB, supprimer de cette clé tout fichier qui proviendrait d’une
version précédente.
Décompresser l’archive en local et copier son contenu (dossier STAGO R, et fichiers
BASEMS.LZH, BASEMUP.LZH, CheckSum.log, EXEBATCH.LZH et install.bat) à la racine
(pas dans un dossier) du support choisi : clé USB ou disquette.
2. Installation du logiciel TSU
Avant d’installer ou de mettre à jour des configurations de test, effectuer une
sauvegarde des méthodologies et des paramètres système.
La navigation dans le logiciel TSU s’effectue au moyen du clavier de l’instrument.
La langue d’exploitation du logiciel TSU est l’anglais.
Accéder au menu Options globales.
Dans la deuxième page, sous Divers/Support de stockage, configurer le support selon le
type choisi (FLP pour une disquette ou USB pour la clé USB).
Insérer le support.
Accéder au menu Maintenance utilisateur .
Lancer la fonctionnalité Mise à jour des données.
Confirmer l’insertion du support en appuyant sur la touche F10.
Le logiciel TSU s’installe et démarre.
Le menu du logiciel TSU s’affiche et propose différentes commandes :
8/18/2019 ALL STA COMPACT INSTALLATION UPDATE
4/24
4/24
Installation/update of online test setups
Installation/mise à jour des méthodologies fournies par téléchargement
0931973B
3. Utilisation du logiciel TSU
3.1. Mise à jour de la base des méthodologies
Dans le menu du logiciel TSU, taper 1.
La fenêtre suivante s’affiche :
Cette fenêtre indique que la mise à jour de la base des méthodologies entraînera la suppression
des dossiers patients, la suppression des produits à bord et la mise à jour de la base des
produits.
Taper y pour continuer (taper n ramène au menu du logiciel TSU).
Les opérations annoncées s’effectuent et les produits ajoutés ou mis à jour s’affichent.
Le menu Test Setup Update s’affiche ensuite :
8/18/2019 ALL STA COMPACT INSTALLATION UPDATE
5/24
Installation/update of online test setups
0931973B
Installation/mise à jour des méthodologies fournies par téléchargement
5/24
Taper 1.
La fenêtre de sélection des méthodologies s’affiche :
Légende :
1 Méthodologies présentes sur le support
2 Code couleur indiquant le statut de la méthodologie :
jaune = obsolète
blanc = méthodologies à jour
rouge = méthodologies à mettre à jour
vert = méthodologies à ajouter
3 Nom complet de la méthodologie4 Date de la méthodologie
5 Réactif déclenchant
6 Méthode de mesure
7 Mode de calibration
8 Unité principale
9 Critères et taux de redilution, limites d’édition
10 Places disponibles restantes pour ajouter des méthodologies
11 Sélection des méthodologies à ajouter/mettre à jour
12 Exécution de l’ajout/de la mise à jour des méthodologies sélectionnées
13 Retour au menu Test Setup Update
Pour passer à la page suivante et voir la suite de la liste, continuer de faire défiler vers le bas.
Sélectionner les méthodologies à ajouter/mettre à jour avec la touche Entrée.
Appuyer sur la touche F10 pour lancer l’ajout/la mise à jour.
La liste des méthodologies concernées défile.
Un message confirme que la procédure de mise à jour de la base client est terminée : "Test
Setup installation done. Press any key to continue".
Appuyer sur une touche pour revenir au menu principal.
REMARQUE : les méthodologies "Obsolete" et "Up to Date" ne peuvent pas être sélectionnées.
8/18/2019 ALL STA COMPACT INSTALLATION UPDATE
6/24
6/24
Installation/update of online test setups
Installation/mise à jour des méthodologies fournies par téléchargement
0931973B
3.2. Changement de conditionnement
Dans le menu du logiciel TSU, taper 1.
La fenêtre suivante s’affiche :
Cette fenêtre indique que la mise à jour de la base des méthodologies entraînera la suppression
des dossiers patients, la suppression des produits à bord et la mise à jour de la base des
produits.
Taper y pour continuer (taper n ramène au menu du logiciel TSU).
Les opérations annoncées s’effectuent et les produits ajoutés ou mis à jour s’affichent.
Le menu Test Setup Update s’affiche ensuite :
Taper 2.
La fenêtre suivante s’affiche
8/18/2019 ALL STA COMPACT INSTALLATION UPDATE
7/24
Installation/update of online test setups
0931973B
Installation/mise à jour des méthodologies fournies par téléchargement
7/24
Légende :
1 Liste des changements de conditionnement (PPC pour Product Packaging Change)
2 Liste des produits concernés par le changement de conditionnement sélectionné dans la zone
MUPPC
3 Informations sur le produit sélectionné dans la zone PRODUCTS
4 Produit remplacé par le produit sélectionné dans la zone PRODUCTS
La navigation entre les différentes zones de la fenêtre s’effectue au moyen de la touche TAB.
Sélectionner le changement de conditionnement qui vous intéresse (repère 1)
Appuyer sur la touche F10 pour installer le ou les produits concernés par le changement de
conditionnement sélectionné (repère 2).
REMARQUE : Tous les produits visibles sous PRODUCTS (repère 2) sont installés. La sélection
dans cette zone sert uniquement à afficher sous INSTALLATION SETTINGS les options
relatives au produit (repère 3) et le produit de remplacement (repère 4).
Le message de confirmation suivant s’affiche :
Appuyer sur la touche Echap pour revenir à la fenêtre PRODUCT PACKAGING CHANGE et
effectuer le cas échéant d’autres changements de conditionnement.
Appuyer sur la touche Echap à partir de la fenêtre PRODUCT PACKAGING CHANGE
permet de revenir au menu Test Setup Update.
8/18/2019 ALL STA COMPACT INSTALLATION UPDATE
8/24
8/24
Installation/update of online test setups
Installation/mise à jour des méthodologies fournies par téléchargement
0931973B
3.3. Suppression de méthodologies
S’assurer qu’aucun test, contrôle ou calibration n’est en cours, sinon attendre que
ces opérations soient terminées avant d’utiliser l’outil de suppression desconfigurations de tests.
Tests calculés et tests dépendants sont supprimés lorsque l’un des tests à partir
desquels ils ont été configurés est supprimé.
La base d’archives doit être effacée. Procéder comme suit :
Quitter TSU.
Sauvegarder les archives à l’aide du TDex.
Supprimer les archives.
Le code d’accès ou le code du jour seront nécessaires.
Dans le menu du logiciel TSU, taper 2.
Le menu de configuration des tests s’affiche.
Placer le curseur sur le test à supprimer.
Appuyer sur Echap, puis sélectionner Supprimer test.
Valider à l’aide de la touche Entrée.
Taper OUI pour confirmer.
Valider à l’aide de la touche Entrée.
Taper le code d’accès. Il peut s’agir, au choix, du mot de passe du menu Configuration de
tests ou du code du jour.
Valider à l’aide de la touche Entrée.
Le test est supprimé.
Appuyer sur Echap, puis sur Entrée pour revenir à l’application TSU.
3.4. Réinitialisation de la base
Dans le menu du logiciel TSU, taper 3.
Un écran s’affiche, qui informe l’utilisateur des données qui seront réinitialisées :
les méthodologies Stago et client, ainsi que l’historique de mise à jour,
la liste des produits Stago et client,
les calibrations,
les résultats de contrôles,
les dossiers patients.
8/18/2019 ALL STA COMPACT INSTALLATION UPDATE
9/24
Installation/update of online test setups
0931973B
Installation/mise à jour des méthodologies fournies par téléchargement
9/24
REMARQUE : les paramètres système (fichiers de cartographie et autres paramètres utilisateur)
sont conservés.
Taper y pour confirmer le lancement de la réinitialisation de la base de données.
La réinitialisation se lance.
Lorsqu’elle est terminée, un message de confirmation s’affiche : "Database erased. Press any
key to continue".
Appuyer sur une touche pour revenir au menu principal.
3.5. Sortie
Dans le menu du logiciel TSU, taper 4, puis appuyer sur n’importe quelle touche pour revenir
au menu Maintenance de l’instrument.
4. Définition ou vérification des paramètres des méthodologies
A partir de l’écran Configuration des tests, exécuter les opérations suivantes :
Sélectionner la méthodologie voulue (touches , , , ), puis valider par la touche .
4.1. Pour une installation
Adapter la configuration par défaut aux besoins du client. Voir la procédure détaillée dans le
Manuel de référence.
Appuyer sur la touche Echap.
Sélectionner Sauvegarder et quitter (touches ou
), puis valider par la touche
.
Saisir le code d’accès (modifier les méthodologies), puis valider par la touche .
Appuyer sur la touche Echap.
Sélectionner Quitter (touches ou ), puis valider par la touche .
Appuyer sur la touche Echap.
Le logiciel revient sur l’écran Tableau de bord.
4.2. Pour une mise à jour
Vérifier que le produit s’affiche bien dans la méthodologie
Vérifier les paramètres de la méthodologie en utlisant les Procédures OpératoiresStandardisées et les impressions des méthodologies du client.
Modifier si nécessaire les paramètres selon les notices de contournement éventuellement
mentionnées dans le BTA.
8/18/2019 ALL STA COMPACT INSTALLATION UPDATE
10/24
10/24
Installation/update of online test setups
Installation/mise à jour des méthodologies fournies par téléchargement
0931973B
Vérifier plus particulièrement les paramètres suivants :
- le changement de conditionnement du réactif (voir champ Flac ml page 1/3)
- les déterminations simple/double (pages 1/3 et 2/3)
- les réactifs utilisés par le client (page 1/3 et Lavage)
- les contrôles de calibration utilisés par le client(page 2/3)
- le rang en transmission (page 3/3)
- les contrôles de qualité utilisés par le client
(page 3/3)
- la période (fréquence de passage) des contrôles de qualité (page 3/3)
Appuyer sur la touche Echap.
Sélectionner Sauvegarder et quitter (touches ou ), puis valider par la touche .
Saisir le code d’accès de Configuration des tests (propre à chaque laboratoire), puis valider
par la touche .
Le logiciel revient à l’écran Configuration des tests.
5. Calibration des tests qui le nécessitent (après une mise à jour)
Calibrer les tests qui le nécessitent : voir le Manuel de référence, chapitre "Calibration",
paragraphe "Procédures de lancement et de validation d’une calibration".
EN CAS DE BESOIN
Si le numéro de lot d’un réactif, calibrant ou contrôle (appelé "produit" dans la procédure
ci-dessous) utilisé après la mise à jour est le même que celui utilisé avant la mise à jour,l’opérateur doit simuler un changement de lot en saisissant les 3 derniers numéros du lot.
A partir de l’écran Tableau de bord, exécuter les opérations suivantes :
Appuyer sur la touche Echap pour afficher la barre des menus.
Sélectionner Chargement (touches ou ), puis valider par la touche .
Sélectionner Produits (touches , ), puis valider par la touche .
Le tiroir s’ouvre automatiquement.
Saisir manuellement le code (champ Id), le nom, le volume et la stabilité du produit, ainsique les 3 derniers caractères du numéro de lot, en validant à chaque fois par la touche .
Placer le flacon de produit dans le tiroir.
Taper OUI, puis valider par la touche
.
Passer le papillon code à barres devant le lecteur code à barres, puis valider par la touche
.
Vérifier que le produit précédent (même numéro de lot) est bien annulé.
8/18/2019 ALL STA COMPACT INSTALLATION UPDATE
11/24
8/18/2019 ALL STA COMPACT INSTALLATION UPDATE
12/24
12/24
Installation/update of online test setups
Installation/mise à jour des méthodologies fournies par téléchargement
0931973B
7. Sauvegarde de la nouvelle base de référence des méthodologies du client
Se reporter au Manuel de référence, chapitre "Maintenance", paragraphe "Utilitaire de
maintenance", sous-paragraphe "Sauvegarde".
Fin du document
8/18/2019 ALL STA COMPACT INSTALLATION UPDATE
13/24
Installation/update of online test setups
0931973B
Installation/mise à jour des méthodologies fournies par téléchargement
13/24
Installation/update of online test setups
Revision
0931973 First release
0931973A Update due to new TSU software version - Document not released.
0931973A Addition of verification/printing/backup steps
Installation and update of online test setups are performed through the use of the Test Setup
Updater software (TSU throughout this document), its minimum version being STB v0.01.01. This
software can be downloaded as a .zip file. Its contents will have be copied to a media - USB keyor floppy - so that it can then be installed on the analyzer. The USB key will be connected to the
IMP box. See diagram below.
Overview of data transfer
Legend:
1 Download of file containing the TSU software and the MS
2 Download of TSB/TAB if needed
3 Decompression and copy to the media
4 Installation on analyzer
20 min
8/18/2019 ALL STA COMPACT INSTALLATION UPDATE
14/24
14/24
Installation/update of online test setups
Installation/mise à jour des méthodologies fournies par téléchargement
0931973B
Update steps
1. Preparing the media
2. Installing the TSU software
3. Using the TSU software
3.1. Updating the test setup base
3.2. Packaging modification
3.3. Deleting test setups
3.4. Resetting the base
3.5. Exit
4. Setting or checking the parameters of the methodologies
4.1. For an installation
4.2. For an update
5. Calibration of the concerned tests (after an update)
6. Printing the customer methodologies
7. Saving the new customer methodology reference base
Prerequisites
- Minimum analyzer version: 108.05/208.05
- PC with Winzip-type data compression software, access to a Diagnostica Stago website, and
equipped with a USB port or a floppy drive
- Get the latest Standardized Operating Procedures (only for Stago methodologies)
- Make sure neither tests, controls, nor calibrations are in progress. If necessary, wait until these
operations are complete.
- Unload all of the tubes and vials from the sample and product drawers.
- The access code allowing the modification of methodologies will be required (see the Reference
Manual, chapter "STATUS and GLOBAL OPTIONS Screens", paragraph "GLOBAL OPTIONS
Screen, page 1", subparagraph "Description of the GLOBAL OPTIONS Screen, page 1").
- Some operations will cause the existing methodology data to be erased. Ensure you always
make a backup copy before proceeding with the steps that are described in this document. Seethe Reference Manual (chapter "Maintenance", paragraph "Maintenance Utility", subparagraph
"Saving").
- Print the customer methodologies (see paragraph 6.Printing the customer methodologies)
- Print the calibrations and quality controls for the methodologies to be updated. Calibrations and
quality controls for these methodologies will be lost.
Necessary tools
- USB key with IMP box or blank floppies with floppy drive
8/18/2019 ALL STA COMPACT INSTALLATION UPDATE
15/24
Installation/update of online test setups
0931973B
Installation/mise à jour des méthodologies fournies par téléchargement
15/24
1. Preparing the media
Get the .zip archive that contains the latest version of the TSU software.
If the chosen media is a USB key, make sure you delete the files from a previous version, if
any.
Locally decompress the archive and copy its contents (folder STAGO R, and files
BASEMS.LZH, BASEMUP.LZH, CheckSum.log, EXEBATCH.LZH, install.bat) to the root (not
a folder) of the chosen media: USB key or floppy.
2. Installing the TSU software
Before installing or updating test setups, make a backup copy of the test setups, and
of the system parameters.
Navigation through the TSU software uses the analyzer keyboard.
English is the operating language of the TSU software.
Go to the Global Options menu.
On the second page, under Miscellaneous/Backup medium, set the appropriate media type
(FLP for a floppy or USB for the USB key).
Insert the media.
Access the User maintenance menu.
Start the Data update feature.
Confirm the media insertion by pressing F10.
The TSU software installs and starts.
The TSU software menu is displayed and offers several commands:
8/18/2019 ALL STA COMPACT INSTALLATION UPDATE
16/24
16/24
Installation/update of online test setups
Installation/mise à jour des méthodologies fournies par téléchargement
0931973B
3. Using the TSU software
3.1. Updating the test setup base
In the TSU software menu, type 1.
The following window is displayed:
Type y to proceed (typing n returns to the TSU software menu).
The listed operations are carried out and the products that were added or updated are
displayed.
The Test Setup Update menu is then displayed:
8/18/2019 ALL STA COMPACT INSTALLATION UPDATE
17/24
Installation/update of online test setups
0931973B
Installation/mise à jour des méthodologies fournies par téléchargement
17/24
Type 1.
The Test setup selection window is displayed:
Legend:
1 Test setups that are on the media
2 Color code indicating the status of the test setup:
yellow = obsolete
white = test setups that are up to date
red = test setups to be updated
green = test setups to be added
3 Full name of the test setup4 Test setup date
5 Start reagent
6 Measurement method
7 Calibration mode
8 Main unit
9 Redilution criteria and rates, edition limits
10 Number of remainging places for adding test setups
11 Selection of test setups to be added/updated
12 Execution of addition/update of selected test setups
13 Back to Test Setup Update menu
To go to the next page and see the continuation of the list, keep scrolling down.
Select the test setups to be added/updated using the Enter key.
Press F10 to start adding/updating the test setups.
The list of the affected test setups scrolls down.
A message confirms the customer base was updated: "Test Setup installation done. Press
any key to continue".
Press any key to return to the main menu.
NOTE: "Obsolete" and "Up to Date" test setups cannot be selected.
8/18/2019 ALL STA COMPACT INSTALLATION UPDATE
18/24
18/24
Installation/update of online test setups
Installation/mise à jour des méthodologies fournies par téléchargement
0931973B
3.2. Packaging modification
In the TSU software menu, type 1.
The following window is displayed:
Type y to proceed (typing n returns to the TSU software menu).
The listed operations are carried out and the products that were added or updated are
displayed.
The Test Setup Update menu is then displayed:
Type 2.
The following window is displayed:
8/18/2019 ALL STA COMPACT INSTALLATION UPDATE
19/24
Installation/update of online test setups
0931973B
Installation/mise à jour des méthodologies fournies par téléchargement
19/24
Legend:
1 List of Product Packaging Changes (PPC)
2 List of products concerned by the packaging change that is selected in the MUPPC area
3 Information about the product that is selected in the PRODUCTS area
4 Product replaced with the product that is selected in the PRODUCTS area
Navigation from one area of the window to another is done using the TAB key.
Select the packaging change you want (mark 1)
Press F10 to install the product(s) concerned by the selected packaging change (mark 2).
NOTE: All the products that are displayed under PRODUCTS (mark 2) are installed. Theselection in this area is only for displaying under INSTALLATION SETTINGS the parameters
related to the product (mark 3) and the replacement product (mark 4).
The following confirmation message is displayed:
Press the Esc key to return to the PRODUCT PACKAGING CHANGE window and if
necessary proceed with other packaging changes.
Pressing the Esc key from the PRODUCT PACKAGING CHANGE returns you to the TestSetup Update menu.
8/18/2019 ALL STA COMPACT INSTALLATION UPDATE
20/24
20/24
Installation/update of online test setups
Installation/mise à jour des méthodologies fournies par téléchargement
0931973B
3.3. Deleting test setups
Make sure neither tests, controls, nor calibrations are in progress. If necessary, wait
until these operations are complete before using the test setup deletion tool.
Calculated and dependent tests will be deleted when one of the tests from which
they were setup is deleted.
The archive base has to be deleted. Do the following:
Exit TSU.
Make a backup copy of the archives using the TDex.
Delete the archives.
The access code is required.
In the TSU software menu, type 2.
The test Setup menu is displayed.
Position the cursor on the test to be deleted.
Press the Esc key, and then select Delete test.
Validate using the Enter key
Type YES to confirm.
Validate using the Enter key Type the access code. You can also choose to use the test Setup menu password.
Validate using the Enter key
The test is deleted.
Press the Esc key, and then the Enter key to return to the TSU software.
3.4. Resetting the base
In the TSU software menu, type 3.
A screen is displayed, which informs the user of the data that will be reset:
the Stago and customer test setups, as well as the update history,
the Stago and customer product list,
the calibrations,
the control results,
the patient files.
8/18/2019 ALL STA COMPACT INSTALLATION UPDATE
21/24
Installation/update of online test setups
0931973B
Installation/mise à jour des méthodologies fournies par téléchargement
21/24
NOTE: the system parameters (mapping files and other user settings) remain unchanged.
Type y to confirm the database reset.
Reset starts.
When it is done, a confirmation message is displayed: "Database erased. Press any key to
continue".
Press any key to return to the main menu.
3.5. Exit
In the TSU software menu, type 4, and then press any key to return to the analyzer
Maintenance menu.
4. Setting or checking the parameters of the methodologies
From the Test panel screen, perform the following operations:
Select the wanted methodology ( ,, , keys), then confirm by pressing the key.
4.1. For an installation
Adjust the default methodology to the customer’s needs. See detailed procedure in the
Reference manual.
Press the Esc key.
Select Save before Quitting, (
or
keys), then confirm by pressing the
key.
Type the access code (modification of test setup), then confirm by pressing the key.
Press the Esc key.
Select Quit ( or keys), then confirm by pressing the key.
Press the Esc key.
The software returns to the Test panel screen.
4.2. For an update
Make sure the product is displayed in the methodology.
Check the parameters of the methodology with the help of the Standardized Operatingprocedures and the printouts of the customer's methodologies.
If necessary, modify the parameters of the methodologies as per the test setting value
instruction sheets referred to in the TAB, if any.
8/18/2019 ALL STA COMPACT INSTALLATION UPDATE
22/24
22/24
Installation/update of online test setups
Installation/mise à jour des méthodologies fournies par téléchargement
0931973B
Check more particularly the following parameters:
- the reagent package update (see the Vial field, page 1/3)
- the single/duplicate determinations (pages 1/3 and 2/3)
- the reagents used by the customer (page 1/3 and Washing)
- the calibration controls used by the customer(page 2/3)
- the transmission rank (page 3/3)
- the quality control used by the customer
(page 3/3)
- the frequency of the quality controls (page 3/3)
Press the Esc key.
Select Save before Quitting, ( or keys), then confirm by pressing the key.
Type the access code for the Test Setup (adapted to each laboratory), then confirm by
pressing the key.
The software returns to the Test Setup screen.
5. Calibration of the concerned tests (after an update)
Calibrate the tests which require it: see the Reference Manual, chapter "Calibration",
paragraph "Procedures to run and validate a Calibration".
IF NEEDED
If the lot number of a reagent, calibrator or control ("product" in the steps described below)
used after the update is the same as the one used before the update, the operator mustsimulate a change of lot by typing the last 3 numbers of the lot.
From the Test panel screen, perform the following operations:
Press the Esc key to show the menu bar.
Select Loading ( or keys), then confirm by pressing the key.
Select Products ( , , keys), then confirm by pressing the key.
The drawer opens automatically.
Type the code (Id field), name, volume and stability for the product, as well as the last 3
digits of the lot, confirming each entry by pressing the key.
Put the product vial in the drawer.
Type YES, then confirm by pressing the
key.
Pass the Assay value insert over the reader, then confirm by pressing the key.
Make sure the previous product (same lot number) is cancelled.
8/18/2019 ALL STA COMPACT INSTALLATION UPDATE
23/24
Installation/update of online test setups
0931973B
Installation/mise à jour des méthodologies fournies par téléchargement
23/24
Press the Esc key.
Select YES ( or keys), then confirm by pressing the key.
Press the Esc key.
Press the Y key, then confirm by pressing the key.
The software returns to the Test panel screen.
6. Printing the customer methodologies
From the Test panel screen, perform the following operations:
Select the wanted methodology ( ,, , keys), then confirm by pressing the key.
Print page 1/3:
- Make sure On line is displayed on the printer (see the printer User Manual).
- Press the Alt and Print screen keys.
Page 1/3 is printed.
Eject the printed page with the Form feed function (see the printer User Manual).
Move the cursor to the Washing before or Washing after field, if the Special or Intensive
parameters are selected ( , ,, keys).
Press the Del key to display the Washing page.
Print the Washing page (see page 1/3).
Press the Esc key to display page 1/3.
Press the key to display page 2/3.
Print page 2/3 (see page 1/3).
Press the key to display page 3/3.
Print page 3/3 (see page 1/3).
Keep the methodology printouts with the other documents delivered during the installation of
the analyzer.
Press the Esc key.
Select Quit without saving, then confirm by pressing the key.
Press the Esc key.
Select Quit, then confirm by pressing the key.
Press the Esc key.
The software returns to the Test panel screen, after the analyzer initialization.
8/18/2019 ALL STA COMPACT INSTALLATION UPDATE
24/24
Installation/update of online test setups
Installation/mise à jour des méthodologies fournies par téléchargement
7. Saving the new customer methodology reference base
See the STA Compact® Reference Manual, chapter "Maintenance", paragraph "Maintenance
Utility", subparagraph "Saving".
End of the document