Post on 02-Mar-2016
description
HomeServicesGetting startedDrawing resourcesMaterialsShowcaseVisit usBlogGet a quote
Drawing resources
Drawing resourcesAdobe Illustrator CSAutoCadCorelDRAWInkscapeTurboCadDrawing serviceExpert TipsFAQ'sAbout Cut Laser Cut
Adobe Illustrator CSThe following guidelines give a detailed step by step overview of how to set up your drawings for us using the Adobe IllustratorSoftware. You can download a demo copy of Adobe Illustrator CS6 here that you can use for up to 30 days.
How to set up a file in Adobe Illustrator CS
Using our drawing templatesIf using your materials or not using a templateConfiguring units & colour modeLaser cutting linesVector engraving / scoring linesRaster engraving lines & fillsNesting components & minimum cut widthsMaintaining continuous vector geometryReducing anchor points / simplifying drawingUsing text - outlining your fontsEmbedding images within a drawingLive tracing imagesReleasing all live paint groupsReleasing all clipping masksCleaning up drawing / removing overlapping linesSaving your file
Using our drawing templates
If using our materials, we recommend downloading our drawing templates. You dont have to use them, but it helps to verify scaleand material type. Materials come in all different sizes depending on the maximum sheet size supplied from the manufacturer.
Templates for Adobe Illustrator can be downloaded from the corresponding material page in the materials gallery. Once downloaded,
Adobe Illustrator drawing setup guidelines for laser cutting & engraving... http://www.cutlasercut.com/resources/drawing-guidelines/adobe-illustr...
1 of 11 27-Feb-14 2:20 PM
select and open the sheet size that is large enough for your components.
Working with the drawing templates
Multiple files from same materialIf you want all your parts cut / engraved from the same material, arrange into multiples of the same templates and draw as many asrequired .
Multiple files from different materialsIf you want parts cut / engraved from multiple materials, Use the corresponding templates for chosen material
Template sizesTry and use templates that suit best the scale of you drawings. i.e if your components can fit within a 1000mm x 500mm template,dont position your drawing on a 2000mm x 1000mm template with lots of excess.
If you have lots of small components from the same material its best to draft these on a series of smaller templates approximately1000mm x 500mm rather than on one large template. Cutting & engraving densely populated files over large areas can cause thematerial to warp during the process.
If you have elements of your drawing that will only fit onto a large template but dont need to use a whole sheet, just leave theremaining areas blank. Well only charge you for the amount of material you need.
If using your materials or not using a template
Set art board to match the size of the material in mmSelect File > New > Set width / size from the top menuAllow 5mm from the border of the material.
Multiple art boards:
Select File > New > Number of Artboards from the top menuYou can use multiple on one file if setting up different files to be cut from the all the same material and thickness only.
Configuring units & colour mode
Measurements: 1 unit = 1mmDraw components at actual size.If copying and pasting vectors from another file, make sure that they are at the scale you requireMake sure you are working in RGB modeSelect File > Document Colour Mode > RGB
Adobe Illustrator drawing setup guidelines for laser cutting & engraving... http://www.cutlasercut.com/resources/drawing-guidelines/adobe-illustr...
2 of 11 27-Feb-14 2:20 PM
Laser cutting lines
For everything you would like to have laser cut draw out your vector strokes in:
Red: RGB: 255,0,0Stroke weight: to 0.01mm / 0.25 pt
Cutting and speed:The laser cuts different materials at varying speeds. As a benchmark it generally takes longer to cut thicker materials than thinnerones. The thicker a material the more power is required at a lower speed. The laser is also faster at cutting straight lines than it is atcutting curves.
Vector engraving / scoring lines
We have established optimized vector / scoring settings for all our materials to achieve a consistant result with the best clarity. Thedepth is very shallow and cosmetic just scratching the surface. The Strokes & Fonts engraving sample (line weight 0.25pt)demonstrates the clarity on each material. These can be viewed in the materials gallery.
For everything you would like to be vector engraved / scored set the strokes to:
Blue: RGB: 0,0,255Stroke weight: to 0.01mm / 0.25 pt
Adobe Illustrator drawing setup guidelines for laser cutting & engraving... http://www.cutlasercut.com/resources/drawing-guidelines/adobe-illustr...
3 of 11 27-Feb-14 2:20 PM
Raster engraving lines & fills
While we can raster engrave thin vector strokes, its advised that you vector engrave/ score them. All vectors you would like rasterengraved must be indicated by a vector fill.
To turn a stroke into a filled shape:
Set strokes to a minimum of 0.40mm. / 1pt (anything thinner wont engrave)Expand strokes. Select Object > Expand > Stroke / Fill
Set all fill colours to:
Black: RGB: 0,0,0
Arrange parts economically
When arranging artwork for engraving that have a few components on one sheet, its best to keep all of the raster engraving as closetogether as possible and in horizontal row. See more on nesting components for raster engraving
Raster engraving standard appearance & depth
We have established optimized settings for all materials. In raster engraving terms the marking is cosmetic, shallow and typically abalance between legibility and cleanliness. The Strokes & Fonts sample on the material pages demonstrates the clarity achievable oneach material.
Bespoke depths / treatments:
If you would like to achieve a deeper result or an engraving a little heavier let us know your specification. In laser terms depth isusually specified in microns.
Up to 2mm is considered deep for most materials:
It is achievable, but the laser has to run slowly meaning the concentrated heat build up makes the material appear quite burnt / heatscorched. It is also more expensive to process. Raster and vector engraving is not absolute science in terms of depth specification andtherefore not suitable for making mechanical grooves or any features requiring precise depths. Achieving a certain depth is a balancein variation between the laser power and speed. A depth of engraving will always be within a tolerance of +/-0.2mm.
Nesting components & minimum cut widths
Nesting:
If compiling a file with lots of components on one sheet of material, make sure there is a gap of at least 2mm between thecomponents.
Small details / cut widths:
Adobe Illustrator drawing setup guidelines for laser cutting & engraving... http://www.cutlasercut.com/resources/drawing-guidelines/adobe-illustr...
4 of 11 27-Feb-14 2:20 PM
As a benchmark, we recommend that minimum cut widths be no smaller than the thickness of the material. E.G. If cutting from3mm acrylic, its best not to allow cut widths less than 3mm. We can go smaller but things can get quite fragile and in somecases can cause the material to warp whilst cutting. You can browse the minimum cut width tests in the materials galley.
Maintaining continuous vector geometry
Try and make sure that all your vector paths are continuous. If strokes / closed shapes are constructed from more than one path,make sure that you join / close the paths.
To do this, use the Direct Selection Tool and select the open endpoints.Select Object > Path > Join (Ctrl+J) from the top menu
Reducing anchor points / simplifying drawing
Draw with the least amount of anchor points possible without sacrificing the drawing appearance. If you can reduce them, we suggestyou do. The machines will process your drawings quicker. Too many anchor points can also impact quality.
You can reduce the number of points with the Simplify toolSelect the stroke path you wish to simplify and select Object > Path > Simplify from the top menuAdjust the sliders until you have maintained a balance between preserving appearance and reducing the number of anchorpoints
Adobe Illustrator drawing setup guidelines for laser cutting & engraving... http://www.cutlasercut.com/resources/drawing-guidelines/adobe-illustr...
5 of 11 27-Feb-14 2:20 PM
Using text - outlining your fonts
All text used needs to be Outlined / converted to paths.
Select Type > Font > Create outlines from the top menu
This is to convert the text to vectors and preserve your font. If you dont do this and we dont have your font installed on ourcomputers, the file will open in default font Myriad or Arial. The middle islands of some letters will fall out when laser cut which canmake the text difficult to read. If you would like to prevent this one option is to use a stencil font.
Embedding images within a drawing
There are 2 options when working with images in illustrator, embedding and using live trace. In both cases images need to be at least300 dpi and in grayscale. We recommend you carry out any image editing in photoshop or Gimp or any other image editingsoftware.
Import your image into your file Select File > Place.* from the top menu barYou can lay vectors over the top of the image for laser cutting of vector engraving
Embedding Linked Images
Adobe Illustrator drawing setup guidelines for laser cutting & engraving... http://www.cutlasercut.com/resources/drawing-guidelines/adobe-illustr...
6 of 11 27-Feb-14 2:20 PM
Select the image you placed in the fileThe Linked File editing tools will appear in the Panel BarSelect the Embed buttonThe Embedded Link icon will appear next to the Linked File in the links window, (Window > Links). Select the icon to embedthe link
Live tracing images
You can also live trace (convert to vectors) the image you want to incorporate within your file.
To do this first select the inserted image, then:
Select Object > Live Trace > Tracing Options. from the top menu barExperiment with the tracing options for the desired effect.Make sure your traced shapes are a solid Black RGB 0,0,0
Releasing all live paint groups
You cant use the live paint function to draft a drawing for laser cutting or engraving. Live paint is an appearance tool specific toillustrator.
Make sure you release all live paint groups. The appearance will not be preserved when saving your file for the laser machine.
View in Outlines (toggle Ctrl+Y.) This mimics how the laser cutter will view and process your drawing.To release Live Paint groups select all vector strokes and fills, Select Object > Live Paint > ReleaseYou can then either then trace or re-draw theses areas
Adobe Illustrator drawing setup guidelines for laser cutting & engraving... http://www.cutlasercut.com/resources/drawing-guidelines/adobe-illustr...
7 of 11 27-Feb-14 2:20 PM
To merge shapes you can also play around with the Pathfinder. Select your vectors then Select Effects > Pathfinder > playaround with the options.Vector strokes can be also be trimmed using the Scissors Tool
Releasing all clipping masks
You cant use the clipping mask function to draft a drawing for laser cutting. Clipping masks are an appearance tool specific toillustrator.
View in Outlines (toggle Ctrl+Y) This mimics how the laser cutter will view and process your drawing.To release clipping masks select all vector strokes and fills, Select Object > Clipping mask > ReleaseYou can then either then trace or redraw them.To merge shapes you can also play around with the Pathfinder Select vectors, Select Effects > Pathfinder > play around withthe options.Vector strokes can be also be trimmed using the Scissors Tool
Cleaning up drawing / removing overlapping lines
When drafting your drawing ensure that there are no duplicate vector strokes stacked up on one another. If you dont get rid of themthe laser will cut / score these lines repeatable, ruining the material and damaging the laser bed.
Adobe Illustrator drawing setup guidelines for laser cutting & engraving... http://www.cutlasercut.com/resources/drawing-guidelines/adobe-illustr...
8 of 11 27-Feb-14 2:20 PM
You can spot duplicates quite easily as the stokes appear darker than other cutting lines.To remove them use the Direct Select tool and delete until you have single lines remaining.
Checking outlines
View in Outlines (toggle Ctrl+Y.) This mimics how the laser cutter will view and process your drawing.If there are any vectors strokes that you dont want to have cut or engraved trim using the Scissors Tool.
Purge your file: Clear the all guides and stray vector points:
Select Select > Object > Stray Points to delete stray vectors not attached to a path.Select View > Guides > Clear Guides to delete all guides.
Saving your file
Select File > Save AsFormat Adobe Illustrator (ai)Any version.
File nameSave your files in the following named format, replacing the fields with the relevant information:
MATERIAL_THICKNESS_ARTBOARDDIMENSION_DRAWINGNAME
The material drawing templates already have the material category name and art-board dimension by default, you will just need toenter your individual material specification and drawing name. Make sure you give easily identifiable names to your drawings:
For example:BIRCH PLYWOOD_3MM_1200x600MM_ARCH MODEL1OF5
Upload your files for a quote
Adobe Illustrator drawing setup guidelines for laser cutting & engraving... http://www.cutlasercut.com/resources/drawing-guidelines/adobe-illustr...
9 of 11 27-Feb-14 2:20 PM
Browse
HomeServicesGetting startedDrawing resourcesMaterialsShowcaseVisit usBlogGet a quote
Get in touchCLCArch 45b South Lambeth Place London SW8 1SR
Follow us
TumblrTwitterFlickrVimeoLinkedInGoogle+
Our newsletter
We hate spam too and will never share your personal details
2011 CLC Creative Ltd. All Rights reserved.Company registration no: 7461306VAT no: 104 8752 20 Terms & conditions
Elsewhere
Adobe Illustrator drawing setup guidelines for laser cutting & engraving... http://www.cutlasercut.com/resources/drawing-guidelines/adobe-illustr...
10 of 11 27-Feb-14 2:20 PM
Raster engraving timelapse.Posted in 1 years on Vimeo
cutlasercut on Flickr
Posted in 1 years on Tumblr
Adobe Illustrator drawing setup guidelines for laser cutting & engraving... http://www.cutlasercut.com/resources/drawing-guidelines/adobe-illustr...
11 of 11 27-Feb-14 2:20 PM