Post on 15-Apr-2017
Technical Paper for Texas Tech University
Receiver Front End for 28-30𝑀𝐻# Transceiver Project
Taslim Anupom
R11368261
Texas Tech University
July 27, 2016
1
Abstract
The technical paper describes the process of how a receiver front end of a transceiver
operates and what are the components required to achieve the optimal performance for the
system. The system receives a signal of frequencies between 28𝑀𝐻# – 30𝑀𝐻#. The signal is then
passed through a series of RF filters, amplifier and a mixer to get an output of 9𝑀𝐻# with a
selectable impedances as discussed in the report. The paper elaborates the above mentioned
topologies of how the system is designed along with full detail about how the system operates.
The paper also includes images and schematics along with detailed explanations for each section
for reference.
2
Table of content:
1. List of Figures………………………………………….…………………….…………………3
2. Introduction………………………………………………….………………………………….4
3. RF Bandpass Filter………….…………………………………….……………….……………5
4. RF 2 Stage Amplifier…………………………...……………….….………….……….….…...8
5. SA 612 Frequency Mixer………………………………………………………….….…….…10
6. Conclusion…………………………………………………………………….....……………12
7. References……………………………………..…………………………………..…….….…15
3
List of Figures:
Figure 1: System Block Diagram………………………………………………………………….5
Figure 2: Bandpass Filter LTSpice Circuit Schematic………………...………………………….5
Figure 3: LTSpice Bandpass Filter Simulation…………………………..……………………….6
Figure 4: Bandpass Filter Spectrum Analyzer Image………………………….………………….7
Figure 5: Suppressed Signals Around Center Frequency……………………...………………….8
Figure 6: RF Amplifier LTSpice Circuit Schematic………………………………………………9
Figure 7: RF Amplifier Resultsat-50dBminputsensitivity………………….……………….10
Figure 8: SA612 Internal Block Diagram…………………………………………..……………11
Figure 9: SA612 LTSpice Circuit Schematic………………………………………...………….11
Figure 10: SA612 Output………………………………………………………………………...12
Figure 11: Receiver Front End Schematic………………………………………….……………13
Figure 12: Receiver Front End Prototype……………………………………….……………….13
Figure 13: Receiver Front End Green Board Design…………………………….………………14
Figure14:ReceiverFrontEndOutputfromGreenBoard………………………………………………..14
4
Introduction:
The main objective for the receiver front end system is to receive a signal, of frequency between
28𝑀𝐻# – 30𝑀𝐻# with center frequency at 29𝑀𝐻# having a characteristic impedance of 50Ω. The
signal is received with a power sensitivity of -100dBm and after filtering the 29𝑀𝐻# signal with
the RF bandpass filter, the signal is later amplified with a two stage RF amplifier and passed to a
SA612 dual balanced mixer and oscillator IC. Finally, at the output of the SA612 mixer, the
system generates multiple frequency but only the 9𝑀𝐻# signal with a selectable impedance of
50Ω or 1500Ω is required from the output of the receiver front end. The Local Oscillator (LO) of
the circuit along with the RF filter to suppress the 9𝑀𝐻# signal was achieved from other systems
developed by separate groups. But for testing purpose, a signal generator with a frequency of
20𝑀𝐻# was used for the LO. Figure 1 below represents the block diagram for the entire system.
The system achieves a gain of 40dB at the end of the receiver which is shown in the following
sections.
5
Figure11:SystemBlockDiagram[1]
RF Bandpass Filter:
The RF bandpass filter used for the system is a coupled resonator filter. To maintain the
center frequency of the filter, the equation 𝜔 = '()
with 𝜔 = 2𝜋𝑓 is used. The tank circuit is
resonant with the frequency(f) at 29𝑀𝐻#. Figure 2 below represents the schematic for the filter.
Figure12:BandpassFilterLTSpiceCircuitSchematic[2]
6
The signal is first stepped up using a transformer. A turn ratio of 3:8 was used for
simulation purpose, but to achieve the actual performance a turn ratio of 2:6 was used. At the
output of the filter another steps down transformer was used with a turn ratio of 6:2 in the actual
system. The 50Ω resistor in the schematic acts as a load for simulation purpose only. The actual
circuit does not have the 50Ω resistor as it is compensated by the input impedance used for the
input source.
Figure 3 below shows the result from the simulation done in LTSpice. From the simulation, the
signal out of the filter has a loss of 6.41dBm. But the actual circuit shows a much better
performance. The actual loss out of the filter is 2.47dB which meets the system requirement as
shown in figure 4 below, the image from the spectrum analyzer (The input 29𝑀𝐻# signal was at
a 0dBm for testing purpose).
Figure13:LTSpiceBandpassFilterSimulation
7
Figure14:BandpassFilterSpectrumAnalyzerImage
For optimal performance of the system, the filter needed to suppress the harmonic
frequencies by a certain power level. Frequencies greater than 2𝑀𝐻#from center was suppressed
by >3dBm, frequencies greater than 5𝑀𝐻# from center was suppressed by >6dBm and signal
greater than 10𝑀𝐻# from center was suppressed by >10dBm. Figure 5 below shows the result
achieved from the filter design. Frequency at 27𝑀𝐻# yields a loss of 9.4dB, 25𝑀𝐻#yields a loss
of 13.34dB, 31𝑀𝐻# yields a loss of 6dB and 33𝑀𝐻# a loss of 12.95 dB, that is all from the
center frequency of 29𝑀𝐻# that only loses 2.47dB.
8
Figure15:SuppressedSignalsAroundCenterFrequency
RF 2 Stage Amplifier:
Following the filter is a 2 stage RF amplifier. The purpose of the two stage amplifier is to
improve the power level of the signal, since the signal coming out of the filter is significantly
weak. The amplifier designed provides a gain of 20 dB which is enough for this part of the
system as more power can be achieved from the latter section of the procedure. Figure 6 below
shows the schematic of the RF amplifier.
9
Figure16:RFAmplifierLTSpiceCircuitSchematic[3]
Signal coming out of the filter goes past a step-up transformer for impedance matching
the filter with the amplifier. To achieve maximum gain from the amplifier along with a 10mA
current stability performance, a 220Ω resistor in parallel with a 1000pF capacitor is used. The
signal output from the amplifier has an impedance of 50Ω on the low side. But for the next part
of the system design, the signal needs to be fed to a 1500Ω mixer. To match the impedance of the
amplifier with the mixer, another step-up transformer was used with a turn ratio of 5:18.
Figure 7 below shows the performance of the amplifier output. The output from the amplifier
gives a gain of 19.5dB from the output of the filter. This time, the 29𝑀𝐻# signal was at a -
50dBm sensitivity. To calculate the turn ratio for the transformers the following equation was
used:
10
𝑧01𝑧234
=𝑁'𝑁6
6
Figure17:RFAmplifierResultsat-50dBminputsensitivity
SA612 Frequency Mixer:
The general description of the mixer “is a low power VHF monolithic double-balanced
mixer with on-board oscillator and voltage regulator.” SA612 is used due to its low cost and low
power communication systems. The frequency mixer is used to produce an intermediate
frequency (IF) of 9𝑀𝐻#. The mixer receives the 29𝑀𝐻# signal from the amplifier and also LO
signal of 20𝑀𝐻#. The output results from the mixer is based on the addition and the subtraction
of the two signals. The signal that is required out of the mixer is the difference between the two,
which is (29-20)𝑀𝐻# = 9𝑀𝐻#. The internal block diagram of the SA612 is shown in figure 8.
11
Figure18:SA612InternalBlockDiagram[4]
The SA612 has two inputs for local oscillator but the project only requires one LO for the
20𝑀𝐻# signal. From the datasheet of the SA612, the single ended untuned configuration was
used due to its simplicity, as well as best fit for the system. The IC is powered using an 8V
regulator which is connected to pin 8. The system uses the same setup configuration provided by
the datasheet for the power. Figure 9 below shows the schematic for the mixer.
Figure19:SA612LTSpiceCircuitSchematic[5]
12
The result from the mixed output is show below in figure 10. This time the input 29𝑀𝐻#signal
was set at -100dBm and from the figure below, at 9𝑀𝐻#a gain of approximate 40dB is achieved.
The output also shows other signals from the mixer as explained earlier but those will be
suppressed from the system added to the output from the mixer from the other group.
Figure20:SA612Output
Conclusion:
The entire system was powered using a 12V source. Figure 11 below shows the entire
circuit schematic combining all the sections that is explained above. The RF filter, amplifier and
mixer schematic contains all the corresponding component values actually used in the system
13
prototype.
Figure11:ReceiverFrontEndCircuitSchematic[6]
Figure 12 below shows the prototype from which all the results have been achieved. A green
board has also been designed as per project requirement which is shown in figure 13 below.
Figure 14 shows the output result from the greenboard system.
Figure12:ReceiverFrontEndPrototype
14
Figure13:ReceiverFrontEndGreenBoardDesign
Figure14:ReceiverFrontEndOutputfromGreenBoard
15
Reference:
1. Dennis F., “System Block Diagram,” (July 02, 2016)
2. Dennis F. & Anupom T., “Bandpass Filter LTSpice Circuit Schematic,” (July 02, 2016)
3. Dennis F. & Anupom T., “RF Amplifier LTSpice Circuit Schematic,” (July 02, 2016)
4. NXP Semiconductors, “SA612A Doubled Balanced Mixer and Oscillator,” 2014,
http://www.nxp.com/documents/data_sheet/SA612A.pdf (July 25, 2016)
5. Dennis F. & Anupom T., “SA612 LTSpice Circuit Schematic,” (July 02, 2016)
6. Dennis F. & Anupom T., “Receiver Front End Circuit Schematic,” (July 02, 2016)