Post on 18-Mar-2020
2014 Ford Fiesta L4-1.6L
Vehicle » Engine, Cooling and Exhaust » Engine » Timing Belt » Service and Repair
Timing Belt
Special Tool(s)/ General Equipment
Removal
NOTICE: Do not loosen or remove the crankshaft pulley bolt without first installing the special tools.
The crankshaft pulley and the crankshaft timing sprocket are not keyed to the crankshaft. Before any
repair requiring loosening or removal of the crankshaft pulley bolt, the crankshaft and camshafts must
be locked in place by the special service tools, otherwise severe engine damage can occur.
NOTICE: During engine repair procedures, cleanliness is extremely important. Any foreign material,
including any material created while cleaning gasket surfaces, that enters the oil passages, coolant
passages or the oil pan can cause engine failure.
1. WARNING: Before beginning any service procedure, refer to Safety Warnings in General
Information See: Testing and Inspection\Initial Inspection and Diagnostic Overview. Failure to follow
this instruction may result in serious personal injury.
Refer to: Health and Safety Precautions See: Service Precautions\Health and Safety Precautions (General
Information, Description and Operation). See: Testing and Inspection\Initial Inspection and Diagnostic
Page 1 of 27ALLDATA Repair - 2014 Ford Fiesta L4-1.6L - Service and Repair
2/18/2017http://alldatapro.com/alldata/PRO~V477018574~C53123~R0~OD~N/0/191164489/19651...
Overview
2. Refer to: Jacking and Lifting - Overview See: Maintenance\Vehicle Lifting\Service and Repair\Jacking
and Lifting (100-02 Jacking and Lifting, Description and Operation).
3. Refer to: Cowl Panel See: Body and Frame\Cowl\Service and Repair\Cowl Panel (501-02 Front End
Body Panels, Removal and Installation).
4. Remove the RH (right-hand) front wheel and tire. Refer to: Wheel and Tire See: Maintenance\Wheels
and Tires\Service and Repair\Removal and Replacement (204-04A Wheels and Tires, Removal and
Installation).
5.
6. Loosen bolts.
Page 2 of 27ALLDATA Repair - 2014 Ford Fiesta L4-1.6L - Service and Repair
2/18/2017http://alldatapro.com/alldata/PRO~V477018574~C53123~R0~OD~N/0/191164489/19651...
7. Refer to: Generator - 1.6L Duratec-16V Ti-VCT (88kW/120PS)- Sigma See: Starting and
Charging\Charging System\Alternator\Service and Repair (414-02 Generator and Regulator, Removal
and Installation).
8.
9. Install the following items: Use the General Equipment: Wooden Block
Use the General Equipment: Trolley Jack
Page 3 of 27ALLDATA Repair - 2014 Ford Fiesta L4-1.6L - Service and Repair
2/18/2017http://alldatapro.com/alldata/PRO~V477018574~C53123~R0~OD~N/0/191164489/19651...
10. NOTICE: The engine mount studs must be held while removing the engine mount nuts or damage
to the powertrain mount may occur.
11.
12.
Page 4 of 27ALLDATA Repair - 2014 Ford Fiesta L4-1.6L - Service and Repair
2/18/2017http://alldatapro.com/alldata/PRO~V477018574~C53123~R0~OD~N/0/191164489/19651...
13.
14.
Page 5 of 27ALLDATA Repair - 2014 Ford Fiesta L4-1.6L - Service and Repair
2/18/2017http://alldatapro.com/alldata/PRO~V477018574~C53123~R0~OD~N/0/191164489/19651...
15.
16.
Page 6 of 27ALLDATA Repair - 2014 Ford Fiesta L4-1.6L - Service and Repair
2/18/2017http://alldatapro.com/alldata/PRO~V477018574~C53123~R0~OD~N/0/191164489/19651...
17. Install Special Service Tool: 303-050 (T70P-6000) Lifting Bracket, Engine.
18. Install Special Service Tool: 303-F072 Support Bar, Engine.
Page 7 of 27ALLDATA Repair - 2014 Ford Fiesta L4-1.6L - Service and Repair
2/18/2017http://alldatapro.com/alldata/PRO~V477018574~C53123~R0~OD~N/0/191164489/19651...
19. Remove the following items: Use the General Equipment: Wooden Block
Use the General Equipment: Trolley Jack
20. NOTE: Only rotate the crankshaft in a clockwise direction.
Page 8 of 27ALLDATA Repair - 2014 Ford Fiesta L4-1.6L - Service and Repair
2/18/2017http://alldatapro.com/alldata/PRO~V477018574~C53123~R0~OD~N/0/191164489/19651...
21.
22. NOTE: The Crankshaft TDC (top dead center) Timing Pin will contact the crankshaft and prevent it from
turning past TDC (top dead center). However, the crankshaft can still be rotated in the counterclockwise
direction. The crankshaft must remain at the TDC (top dead center) position during the crankshaft pulley
removal and installation.
Install Special Service Tool: 303-748 Locking Tool, Crankshaft.
Page 9 of 27ALLDATA Repair - 2014 Ford Fiesta L4-1.6L - Service and Repair
2/18/2017http://alldatapro.com/alldata/PRO~V477018574~C53123~R0~OD~N/0/191164489/19651...
23. NOTE: Only rotate the crankshaft clockwise direction.
Rotate the crankshaft slowly clockwise until the crankshaft balance weight is up against the crankshaft locking
tool. The engine is now at TDC (top dead center).
24.
Page 10 of 27ALLDATA Repair - 2014 Ford Fiesta L4-1.6L - Service and Repair
2/18/2017http://alldatapro.com/alldata/PRO~V477018574~C53123~R0~OD~N/0/191164489/19651...
25. NOTE: It may necessary to rotate the camshafts slightly to install the special tool.
Install Special Service Tool: 303-1097 Locking Tool, Variable Camshaft Timing Oil Control Unit.
26.
Page 11 of 27ALLDATA Repair - 2014 Ford Fiesta L4-1.6L - Service and Repair
2/18/2017http://alldatapro.com/alldata/PRO~V477018574~C53123~R0~OD~N/0/191164489/19651...
27. WARNING: The timing belt tensioner spring is under load. Extra care must be taken at all times
when handling the tensioner. Failure to follow this instruction may result in personal injury.
Installation
1.
Page 12 of 27ALLDATA Repair - 2014 Ford Fiesta L4-1.6L - Service and Repair
2/18/2017http://alldatapro.com/alldata/PRO~V477018574~C53123~R0~OD~N/0/191164489/19651...
2. WARNING: The timing belt tensioner spring is under load. Extra care must be taken at all times
when handling the tensioner. Failure to follow this instruction may result in personal injury.
Page 13 of 27ALLDATA Repair - 2014 Ford Fiesta L4-1.6L - Service and Repair
2/18/2017http://alldatapro.com/alldata/PRO~V477018574~C53123~R0~OD~N/0/191164489/19651...
3. Torque : 80 lb.in (9 Nm)
4. NOTE: The final torque of the crankshaft will be completed in the following steps.
Torque : 74 lb.ft (100 Nm)
Page 14 of 27ALLDATA Repair - 2014 Ford Fiesta L4-1.6L - Service and Repair
2/18/2017http://alldatapro.com/alldata/PRO~V477018574~C53123~R0~OD~N/0/191164489/19651...
5. Remove Special Service Tool: 303-748 Locking Tool, Crankshaft.
6. Remove Special Service Tool: 303-1097 Locking Tool, Variable Camshaft Timing Oil Control Unit.
Page 15 of 27ALLDATA Repair - 2014 Ford Fiesta L4-1.6L - Service and Repair
2/18/2017http://alldatapro.com/alldata/PRO~V477018574~C53123~R0~OD~N/0/191164489/19651...
7. Torque : Stage 1: 90°
Stage 2: Wait 2s
Stage 3: 15°
8. NOTE: Only rotate the crankshaft clockwise direction.
Rotate about 1 3/4 turns.
Page 16 of 27ALLDATA Repair - 2014 Ford Fiesta L4-1.6L - Service and Repair
2/18/2017http://alldatapro.com/alldata/PRO~V477018574~C53123~R0~OD~N/0/191164489/19651...
9. Install Special Service Tool: 303-748 Locking Tool, Crankshaft.
10. Rotate the crankshaft until it stops against the Crankshaft Locking Tool.
Page 17 of 27ALLDATA Repair - 2014 Ford Fiesta L4-1.6L - Service and Repair
2/18/2017http://alldatapro.com/alldata/PRO~V477018574~C53123~R0~OD~N/0/191164489/19651...
11. NOTE: The special tool can only be installed if the valve timing is correct.
Install Special Service Tool: 303-1097 Locking Tool, Variable Camshaft Timing Oil Control Unit.
12. Remove Special Service Tool: 303-1097 Locking Tool, Variable Camshaft Timing Oil Control Unit.
Page 18 of 27ALLDATA Repair - 2014 Ford Fiesta L4-1.6L - Service and Repair
2/18/2017http://alldatapro.com/alldata/PRO~V477018574~C53123~R0~OD~N/0/191164489/19651...
13. Remove Special Service Tool: 303-748 Locking Tool, Crankshaft.
14. Torque : 177 lb.in (20 Nm)
Page 19 of 27ALLDATA Repair - 2014 Ford Fiesta L4-1.6L - Service and Repair
2/18/2017http://alldatapro.com/alldata/PRO~V477018574~C53123~R0~OD~N/0/191164489/19651...
15. Install the following items: Use the General Equipment: Wooden Block
Use the General Equipment: Trolley Jack
16. Remove Special Service Tool: 303-F072 Support Bar, Engine.
Page 20 of 27ALLDATA Repair - 2014 Ford Fiesta L4-1.6L - Service and Repair
2/18/2017http://alldatapro.com/alldata/PRO~V477018574~C53123~R0~OD~N/0/191164489/19651...
17. Remove Special Service Tool: 303-050 (T70P-6000) Lifting Bracket, Engine.
18.
1. Torque : 41 lb.ft (55 Nm)
2. Torque : 41 lb.ft (55 Nm)
Page 21 of 27ALLDATA Repair - 2014 Ford Fiesta L4-1.6L - Service and Repair
2/18/2017http://alldatapro.com/alldata/PRO~V477018574~C53123~R0~OD~N/0/191164489/19651...
19. Hand start the bolts in the sequence shown. Torque :
Stage 1: 1 and 3-8: 89 lb.in (10 Nm)
Stage 2: 2: 89 lb.in (10 Nm)
20. Finger tight.
Page 22 of 27ALLDATA Repair - 2014 Ford Fiesta L4-1.6L - Service and Repair
2/18/2017http://alldatapro.com/alldata/PRO~V477018574~C53123~R0~OD~N/0/191164489/19651...
21. Finger tight.
22. NOTICE: The 2 engine mount studs must be torqued or damage to the powertrain mount may
occur.
Torque : 71 lb.in (8 Nm)
Page 23 of 27ALLDATA Repair - 2014 Ford Fiesta L4-1.6L - Service and Repair
2/18/2017http://alldatapro.com/alldata/PRO~V477018574~C53123~R0~OD~N/0/191164489/19651...
23. Torque : 35 lb.ft (48 Nm)
24. Torque : 59 lb.ft (80 Nm)
Page 24 of 27ALLDATA Repair - 2014 Ford Fiesta L4-1.6L - Service and Repair
2/18/2017http://alldatapro.com/alldata/PRO~V477018574~C53123~R0~OD~N/0/191164489/19651...
25. Remove the following items: Use the General Equipment: Wooden Block
Use the General Equipment: Trolley Jack
26.
Page 25 of 27ALLDATA Repair - 2014 Ford Fiesta L4-1.6L - Service and Repair
2/18/2017http://alldatapro.com/alldata/PRO~V477018574~C53123~R0~OD~N/0/191164489/19651...
27. Refer to: Generator - 1.6L Duratec-16V Ti-VCT (88kW/120PS)- Sigma See: Starting and
Charging\Charging System\Alternator\Service and Repair (414-02 Generator and Regulator, Removal
and Installation).
28. Torque : 18 lb.ft (24 Nm)
29. Torque : 80 lb.in (9 Nm)
Page 26 of 27ALLDATA Repair - 2014 Ford Fiesta L4-1.6L - Service and Repair
2/18/2017http://alldatapro.com/alldata/PRO~V477018574~C53123~R0~OD~N/0/191164489/19651...
30. Install the RH (right-hand) front wheel and tire. Refer to: Wheel and Tire See: Maintenance\Wheels and
Tires\Service and Repair\Removal and Replacement (204-04A Wheels and Tires, Removal and
Installation).
31. Refer to: Cowl Panel See: Body and Frame\Cowl\Service and Repair\Cowl Panel (501-02 Front End
Body Panels, Removal and Installation).
32. Perform the Misfire Monitor Neutral Profile Correction procedure.
Page 27 of 27ALLDATA Repair - 2014 Ford Fiesta L4-1.6L - Service and Repair
2/18/2017http://alldatapro.com/alldata/PRO~V477018574~C53123~R0~OD~N/0/191164489/19651...