Post on 22-Nov-2015
description
Tower Of RetributionBy BugBait NZ
Plans By Irondad DK
Cut all the way through
Cut through cardboard from this side
Cut through cardboard from other side
1 Inch and 1cm, for scale
Fold Line, score, but do not cut.
Welcome to a really big project!I mean it, this is really really BIG!!Do not attempt this if you are not comfortable with working with foamboard, you need to learn by making mistakes and learning from that experience.I recommend trying the small bugbunker fist. Tools neededInvest in a good snapoff blade and a lot of spare blades, cheap blades only create more work and wasted foamboardPatienceA steal rulePatienceCutting matdid I mention patience? Cutting foamboard 101You can only cut foamboard with a surgicaly sharp knife, as soon as the blade stops sliding smoothly snap off the tip.You should not attempt to cut through on only one passThe first cut should be light to just mark the foamboardsecond cut should get though the first layer of paperNow your blade will follow the cut you need to focus on keeping the blade at the right angle, this takes practice! Feel free to ask questions on either of these forums Warseer Terrain Project Logs "Apocalypse 40k Terrain" http://www.warseer.com/forums/showthread.php?t=109769Terragenesis WIP "Bugbaits random 40k thread" http://www.terragenesis.co.uk/forum/viewtopic.php?t=6372
Legend
4XA1
A
5.0
120.0
110.0
85.0
5mm foamboard
A125.0
125.
0
5.0
A2 1X
5mm foamboard
BB1
4X
355.
517
125
114
15 243.3
28
12
4
5
5mm foamboard
B82.2
82.2
B2 1X
5mm foamboard
1X
C
240
.64
60
C1
5mm foamboard
39
65
5
C2 6X
60
5
180
20
C
C3
5mm foamboard
1X
60
5
20
180 C
C4
5mm foamboard
1X
260
242.4
232.4250
70.6
4
.64
C
C5 Parts C6 and C7 have the same measurementsas part C5, except for the holes.
5mm foamboard
CDO NOT Make this part!Unless:You are extremely accurate,you want the exact layout as shown on the frontpage,and/or you didn't bother to read this. INSTEAD you should make 3 copies of part C5, and make the holes later when you have decided what yourlayout should be. See Bugbaits build log for details howto make the holes.
C6 1X
5mm foamboard
DO NOT Make this part!Unless:You are extremely accurate,you want the exact layout as shown on the frontpage,and/or you didn't bother to read this. INSTEAD you should make 3 copies of part C5, and make the holes later when you have decided what yourlayout should be. See Bugbaits build log for details howto make the holes.
C
1XC7
5mm foamboard
70
.64
7061.2
56.265
C
C8
C9
1X
1X
68.8
25
16.2
C10
2X
5mm foamboard
85.9110
5070
67.9
80
5070
C
C11 1X
5mm foamboard
70 21.2 90 21.2 70
272.4
4.1
45
C
Fold lines - DO NOT CUT!!!
C12 1X
5mm foamboard
49.6
69
49.669
C
C13 1X
5mm foamboard
Strip is longer than needed, cut to fit.
C0.5mm Card
C14 1X C15 1X
C161X
0.5mm Card Decoration - optional
Wall detail, use as guide and cut to fit.
0.5mm Card Decoration - optional
0.5mm Card Decoration - optional
103.
6
1.5
16
82.861.5
2229
39.52.2
58
5mm foamboard D
D1
Make 8 pr. cone.2 of each 8 are used to make parts D2 and D3
16X
33
1956
7
1.5
56.8
88
45.2
1.5
D5mm foamboard
Made from part D1
D2 D32X 2X
50.633
29.547
68.5
68
1.5
46.6 5
3
18.632
D5mm foamboard
D4
D5
Make 6 pr. cone.
Make 1 pr. cone.
12X
2X
64.7
156.
3
64.7156.3
1.5
6
353
52.2
90.2
Make as many as nescessary.
D5mm foamboard
D6
D7
2X
D0.5mm Card
D8 2X
D9 2XD102X
0.5mm Card Decoration - optional
1020.4
51
16.4
69.4
15.6
85
8.8
1X+1 Mirrored
62.8
61.5
50.4
.6
5mm foamboard E
E1/2
E3 1X
165.6
2.4
14
F5mm foamboard
1XF1
194.8
2.4
5.5
F5mm foamboard
F2 1X
193.629.8
.4 1
F5mm foamboard
F3 1X
72.8
62.8
39
75
5
3
Make as many as nescessary.
Make as many as nescessary.Cut to fit. Corner supports are slightlylonger than regular wall supports.
F5mm foamboard
F4 F5
51.5
18
5mm foamboard F
F6 4X
15
27
0.5mm Card Decoration - optional
10.2
19
13.5
301.
5
26.9
13.55.4
1.2 8.21
.5
MixedAccessories - G
5mm foamboard
G1 1X
G2 1X
40
3
0.5mm Card
Strip
is lo
nger
tha
n ne
eded
, cu
t to
fit.
1XG32XG4
SECTION A-ASCALE 1 / 4
SECTION B-BSCALE 1 / 4
A A
B B54
200200
10
215.
6
10
Tip.Begin by marking the outline of a cone on apiece of paper/cardboard/worktable.Place the Roof in the middle of the outline,and raise it to 54mm above the outline.Now you should be able to dryfit the walls, simply by placing them on the outline, and lean them against the roof.
Bottom View
Top View
Cone
Main Tower
Main Gate
Front View
Bottom View
Assembly Details
Tower Assembly